Z00607MA 1BA2

**Z00607** 

## Standard 0.8 A Triacs 

**Datasheet** - **production data** 

**==> picture [162 x 161] intentionally omitted <==**

**----- Start of picture text -----**<br>
A2<br>G<br>™<br>A1<br>A2<br>G<br>A2 A2<br>G A1<br>A1<br>TO-92 SOT-223<br>Z00607MA Z00607MN<br>**----- End of picture text -----**<br>


## **Description** 

The Z00607 is suitable for low power AC switching applications. Typical applications include home appliances (electrovalve, pump, door lock, small lamp control), fan speed controllers,... 

Thanks to the low gate triggering current these triacs can be driven directly by microcontrollers. 

## **Features** 

- On-state rms current = 0.8 A 

- Repetitive peak off-state voltage = 600 V 

- Gate triggering current = 5 mA 

June 2014 

DocID6629 Rev 9 

1/8 

This is information on a product in full production. 

_www.st.com_ 

**Characteristics** 

**Z00607** 

## **1 Characteristics** 

**Table 1. Absolute maximum ratings** 

||**Table 1. Absolute maximum ratings**|**Table 1. Absolute maximum ratings**|**Table 1. Absolute maximum ratings**|||
|---|---|---|---|---|---|
|**Symbol**|**Parameter**|||**Value**|**Unit**|
|IT(RMS)|On-state rms current<br>(full sine wave)|SOT-223|Ttab= 85 °C|0.8|A|
|||TO-92|TL= 50 °C|||
|ITSM|Non repetitive surge peak on-state<br>current  (full cycle, Tjinitial = 25 °C)|F = 50 Hz|t = 20 ms|9|A|
|||F = 60 Hz|t = 16.7 ms|9.5||
|I²t|I²t Value for fusing|tp= 10 ms||0.45|A²s|
|dI/dt|Critical rate of rise of on-state current IG<br>= 2 x IGT, tr ≤100 ns|F = 120 Hz|Tj= 110 °C|20|A/µs|
|IGM|Peak gate current|tp= 20 µs|Tj= 110 °C|1|A|
|PG(AV)|Average gate power dissipation||Tj= 110 °C|0.1|W|
|Tstg<br>Tj|Storage junction temperature range<br>Operating junction temperature range|||- 40 to + 150<br>- 40 to + 110|°C|



**Table 2. Electrical characteristics (Tj = 25 °C, unless otherwise specified)** 

|**Symbol**|**Test Conditions**|**Quadrant**||**Value**|**Unit**|
|---|---|---|---|---|---|
|IGT<br>(1)|VD= 12 V, RL= 30Ω|I - II - III|MAX|5|mA|
|||IV||7||
|VGT||ALL|MAX|1.3|V|
|VGD|VD= VDRM,RL= 3.3 kΩ, Τj= 110 °Χ|ALL|MIN|0.2|V|
|IH<br>(2)|IT= 200 mA||MX.|5|mA|
|IL|IG= 1.2 IGT|I - III - IV|MAX|10|mA|
|||II||20||
|dV/dt<br>(2)|VD=  67% VDRM, gate openΤj= 110 °Χ||MIN|10|V/µs|
|(dV/dt)c<br>(2)|(δς/δτ)χ = 0.35 Α/μσ, Τj= 110 °Χ||MIN|1.5|V/µs|



1. minimum IGT is guaranteed at 5% of IGT max. 

2. for both polarities of A2 referenced to A1. 

**Table 3. Static characteristics** 

||**Table 3. Static characteristics**|**Table 3. Static characteristics**|**Table 3. Static characteristics**|||
|---|---|---|---|---|---|
|**Symbol**|**Test Conditions**|||**Value**|**Unit**|
|VTM<br>(1)|ITM= 1.1 A        tp= 380 µs|Tj= 25 °C|MAX.|1.5|V|
|Vto<br>(1)|Threshold voltage|Tj= 110 °C|MAX.|0.95|V|
|Rd<br>(1)|Dynamic resistance|Tj= 110 °C|MAX.|420|mΩ|
|IDRM<br>IRRM|VDRM= VRRM= 600 V|Tj= 25 °C|MAX.|5|µA|
|||Tj= 110 °C||0.1|mA|



1. for both polarities of A2 referenced to A1. 

2/8 

DocID6629 Rev 9 

**Characteristics** 

**Z00607** 

**Table 4. Thermal resistances** 

|**Symbol**||**Parameter**|**Parameter**|**Value**|**Unit**|
|---|---|---|---|---|---|
|Rth(j-t)|Junction to tab (AC)||SOT-223|25|°C/W|
|Rth(j-I)|Junction to lead (AC)||TO-92|60||
|Rth(j-a)|Junction to ambient|S(1)= 5 cm²|SOT-223|60|°C/W|
||||TO-92|150||



1. S = Copper surface under tab. 

**Figure 1. Maximum power dissipation versus RMS on-state current (full cycle)** 

**Figure 2. Relative variation of gate trigger, holding and latching current versus junction temperature** 

**==> picture [462 x 147] intentionally omitted <==**

**----- Start of picture text -----**<br>
P(W) IGT, IH, IL [T ] /j IGT, IH, IL [T =25°C]j<br>1.0 2.5<br>0.9 Typical values<br>0.8 2.0<br>0.7 I GT<br>0.6 1.5<br>0.5<br>IH & IL<br>0.4 1.0<br>0.3<br>0.2 0.5<br>0.1 I T(RMS) (A) T j (°C)<br>0.0 0.0<br>0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 -40 -20 0 20 40 60 80 100 120<br>**----- End of picture text -----**<br>


**Figure 3. Surge peak on-state current versus number of cycles** 

**Figure 4. Non-repetitive surge peak on-state current and corresponding value of I[2] t** 

**==> picture [462 x 146] intentionally omitted <==**

**----- Start of picture text -----**<br>
ITSM (A) ITSM (A), I2t (A2s)<br>10 200.0<br>9 100.0 Tj initial = 25°C<br>8 t=20ms dI/dt limitation:<br>76 TNon repetitivej initial = 25°C One cycle 10.0 20A/µs ITSM<br>5<br>4 Repetitive<br>3 T amb = 25°C 1.0<br>2 I2t<br>1<br>0 Number of cycles 0.1 Sinusoidal pulse with width tp < 10 ms tp (ms)<br>1 10 100 1000 0.01 0.10 1.00 10.00<br>**----- End of picture text -----**<br>


DocID6629 Rev 9 

3/8 

**Characteristics** 

**Z00607** 

**Figure 5. On-state characteristics (maximum values)** 

**Figure 6. Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values)** 

**==> picture [462 x 340] intentionally omitted <==**

**----- Start of picture text -----**<br>
ITM(A) (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c<br>10.0 10.0<br>8.0<br>Tj = Tjmax. 6.0<br>1.0<br>4.0<br>T =max. j<br>Tj = 25°C RVdt0=420 m=0.95 V Ω 2.0<br>0.1 VTM (V) 0.0 (dV/dt)c (V/µs)<br>0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.1 1.0 10.0<br>Figure 7. Relative variation of critical rate of  Figure 8. SOT-223 Thermal resistance junction<br>decrease of main current versus junction  to ambient versus copper surface under tab<br>temperature<br>(dI/dt)c [T ] /j (dI/dt)c [Tj Specified] Rth(j-a)(°C/W)<br>6 130<br>120 Printed circuit board FR4,<br>5 110 copper thickness = 35 µm<br>100<br>90<br>4<br>80<br>70<br>3<br>60<br>50<br>2 40<br>30<br>1 20<br>T j (°C) 10 S(cm²)<br>0 0<br>0 10 20 30 40 50 60 70 80 90 100 110 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0<br>**----- End of picture text -----**<br>


4/8 

DocID6629 Rev 9 

**Ordering information scheme** 

**Z00607** 

## **2 Ordering information scheme** 

## **Figure 9. Ordering information scheme** 

**==> picture [312 x 183] intentionally omitted <==**

**----- Start of picture text -----**<br>
Z   006   07   M   A   Blank   1BA2<br>Triac series<br>Current<br>006 = 0.8A<br>Sensitivity<br>07 = 5mA<br>Voltage<br>M = 600V<br>Package<br>A = TO-92<br>N = SOT-223<br>Packing mode<br>1BA2 = TO-92 Bulk<br>2BL2 = TO-92 Ammopack<br>5BL2 = TO-92 Tape and reel<br>5AA4 = SOT-223 Tape and reel<br>**----- End of picture text -----**<br>


DocID6629 Rev 9 

5/8 

**Packaging information** 

**Z00607** 

## **3 Packaging information** 

- Epoxy meets UL94, V0 

- Lead-free package 

In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK[®] packages, depending on their level of environmental compliance. ECOPACK[®] specifications, grade definitions and product status are available at: www.st.com. ECOPACK[®] is an ST trademark. 

**Table 5. SOT-223 dimensions** 

|**A**<br>**H**||||||||**V**<br>**c**|**V**<br>**c**|**V**<br>**c**|**Ref.**|**Dimensions**|**Dimensions**|**Dimensions**|**Dimensions**|**Dimensions**|**Dimensions**|
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|||||||||||||**Millimeters**|||**Inches**|||
|||||||||||||**Min.**|**Typ.**|**Max.**|**Min.**|**Typ.**|**Max.**|
|||||**e1**<br>**D**<br>**B1**<br>**e**<br>**2**<br>**4**<br>**3**<br>**B**<br>||||**V**||||||||||
|||||||||||||||||||
||**A1**||||||||||A|||1.80|||0.071|
||||||||||||A1||0.02|0.10||0.001|0.004|
||||||||||||B|0.60|0.70|0.85|0.024|0.027|0.033|
||||||||||||B1|2.90|3.00|3.15|0.114|0.118|0.124|
|||||**B1**||||||||||||||
||**E**||||||||||c|0.24|0.26|0.35|0.009|0.010|0.014|
|||||||||||||||||||
||||||**4**||||||D(1)|6.30|6.50|6.70|0.248|0.256|0.264|
||||**1**||**2**<br>**3**||||||e||2.3|||0.090||
|||||||||||||||||||
||||||||||||e1||4.6|||0.181||
|||||||||||||||||||
||||||||||||E(1)|3.30|3.50|3.70|0.130|0.138|0.146|
||||||||||||H|6.70|7.00|7.30|0.264|0.276|0.287|
||||||||||||V|10° max||||||



1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches) 

**Figure 10. Footprint (dimensions in mm)** 

**==> picture [160 x 155] intentionally omitted <==**

**----- Start of picture text -----**<br>
3.25<br>1.32<br>5.16 7.80<br>1.32<br>2.30 0.95<br>**----- End of picture text -----**<br>


6/8 

DocID6629 Rev 9 

**Ordering information** 

**Z00607** 

**Table 6. TO-92 dimensions** 

|**A**<br>**F**<br>**C**<br>**B**||||**a**<br>**E**|**Ref.**|**DIMENSIONS**|**DIMENSIONS**|**DIMENSIONS**|**DIMENSIONS**|**DIMENSIONS**|**DIMENSIONS**|
|---|---|---|---|---|---|---|---|---|---|---|---|
|||||||**Millimeters**|||**Inches**|||
|||||||**Min.**|**Typ.**|**Max.**|**Min.**|**Typ.**|**Max.**|
|||||||||||||
||||||A<br>B||1.35|4.70||0.053|0.185|
||||||C||2.54|||0.100||
||||||D|4.40|||0.173|||
||||**D**|||||||||
||||||E|12.70|||0.500|||
||||||F|||3.70|||0.146|
||||||a|||0.50|||0.019|



## **4 Ordering information** 

**Table 7. Ordering information** 

|**Ordering type**|**Marking**|**Package**|**Weight**|**Base**<br>**quantity**|**Delivery**<br>**mode**|
|---|---|---|---|---|---|
|Z00607MA 1BA2|Z0607MA|TO-92|0.2 g|2500|Bulk|
|Z00607MA 2BL2|Z0607MA|||2000|Ammopack|
|Z00607MA 5BL2|Z0607MA|||2000|Tape and reel|
|Z00607MN 5AA4|Z06M|SOT-223|0.12 g|1000|Tape and reel|



## **5 Revision history** 

**Table 8. Document revision history** 

|**Date**|**Revision**|**Changes**|
|---|---|---|
|Oct-2001|4|Last update.|
|25-Mar-2005|5|Package: TO-92 tape and reel delivery mode 5BL2 added.|
|21-Jun-2005|6|Markings updated from Z006xxxx to Z06xxxx|
|13-Sep-2005|7|Z00607MA 2BL2: marking corrected from 00607mA to<br>Z0607MA|
|12-Apr-2007|8|Reformatted to current standard. Added SOT-223 package.<br>Changed Tj from +125 to +110 in_Table 1_|
|19-Jun-2014|9|Updated marking for Z00607MN 5AA4 in_Table 7_.|



DocID6629 Rev 9 

7/8 

**Z00607** 

## **Please Read Carefully:** 

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. 

All ST products are sold pursuant to ST’s terms and conditions of sale. 

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. 

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. 

**UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.** 

**ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.** 

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. 

ST and the ST logo are trademarks or registered trademarks of ST in various countries. 

Information in this document supersedes and replaces all information previously supplied. 

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 

© 2014 STMicroelectronics - All rights reserved 

STMicroelectronics group of companies 

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 

## **www.st.com** 

8/8 

DocID6629 Rev 9