W33-T4B1Q-15

Catalog 1308242 Issued 3-03 (PDF Rev. 9-05) 

_P&B_ 

## W33 series 

## **One- and Two-Pole, Switchable Thermal Circuit Breaker / Power Switch With Optional Indicator Lamp** 

## **Features** 

- Combines on/off switch and circuit protection in a single unit. 

- 2 to 20 amp ratings (<2A types available as special order). 

- One or two pole sensing. 

- Lighted or non-lighted rocker actuator in various colors. 

- Convenient, snap-in mounting. 

- Optional auxiliary switch available. 

- Trip-free operation. 

## **Electrical Data @ 25°C** 

**Calibration:** Breaker will continuously carry 100% of rated load. It may trip between 101% and 135%, but must trip at 135% within one hour at +25°C. 

**Dielectric Strength:** Over 2,000 volts RMS. 

**Maximum Operating Voltages:** 50VDC; 250VAC to 400 Hz. 

**Interrupt Capacity:** 1,000 amps at 50VDC; 250VAC, 60 Hz. and 125/250VAC, 400 Hz. 1,500 amps at 125/250VAC, 60 Hz. **Resettable Overload Capacity:** Ten times rated current. 

## **Agency Approvals** 

**W33 series is UL 1077 Recognized as Supplementary Protectors, File E69543, and CSA Accepted as Supplementary Protectors (Appliance Component Protectors), File LR15734.** 

Users should thoroughly review the technical data before selecting a product part number. It is recommended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. 

## **Mechanical/Environmental Data** 

**Termination: Poles 1&2:** .250” (6.35mm) quick connect/solder terminals. **Opt. Aux. Sw.:** .110”(2.79mm) quick connect terminals. **Mounting:** Snaps into panel from front. **Actuator:** Rocker or lighted rocker **. Shock:** 30g tested to IEC 68-2-27, test Ea **. Vibration:** 8g tested to IEC 68-2-6, test Fc. **Switch Endurance Cycling:** 50,000 operations at rated load. 1,000 operations at 200% rated load **.** 

## **Time vs. Current Trip Curve @ +25°C** 

**==> picture [346 x 170] intentionally omitted <==**

**----- Start of picture text -----**<br>
1000<br>900 _ ne CO OverloadAll ModelsTrip Times<br>100% No Trip<br>800 NS 135% Trip in 1 hour<br>200% 3.0 - 33 Sec.<br>700 AC SPI 400% 0.6 - 10 Sec.<br>N 600% 0.34 - 5 Sec.<br>600 800% 0.25 - 2.2 Sec.<br>NEI 1000% 0.20 - 0.6 Sec.<br>500<br>CAE NTE<br>400<br>CONE CTI<br>300 0  ETT<br>200<br>TISSST TT<br>1000 CCRieSC ri<br>.1 1 10 100 1000<br>Time In Seconds<br>Of Breaker Rating<br>Load Current As A Percent<br>**----- End of picture text -----**<br>


## **Ambient Compensation Chart** 

**==> picture [151 x 111] intentionally omitted <==**

**----- Start of picture text -----**<br>
1.40<br>1.30 NGSeeeeee<br>1.20<br>PEN EEE<br>1.10<br>KEN EE<br>1.00 rt tTEINE<br>0.90 EL LI<br>0.80<br>FECES<br>0.70<br>ECCEECSKES<br>0.60<br>Cerne –20 –10 0 10 20 30 40 50 60<br>Correction Factor<br>**----- End of picture text -----**<br>


**Ambient Temperature In Degrees Centigrade (°C)** 

**To use this chart:** Read up from the ambient temperature to the curve, and across to find a correction factor. Multiply the breaker rating by the correction factor to determine the compensated rating. Calculate the overloads in terms of the compensated rating to use the published trip curve. 

Specifications and availability subject to change. 

Dimensions are in inches over (millimeters) unless otherwise specified. 

Dimensions are shown for reference purposes only. 

www.tycoelectronics.com Technical support: Refer to inside back cover. 

114 

Catalog 1308242 Issued 3-03 (PDF Rev. 9-05) 

_P&B_ 

## ~~**Ordering Information**~~ 

**==> picture [364 x 12] intentionally omitted <==**

**----- Start of picture text -----**<br>
Typical Part No.   B W 33 -S 1 N 1 Q -20<br>**----- End of picture text -----**<br>


**==> picture [467 x 217] intentionally omitted <==**

**----- Start of picture text -----**<br>
1. Designator:<br>W = Circuit breaker<br>2. Series Number:<br>33 = Two pole, rocker actuated<br>3. Circuit Function:<br>S = Pole 1 – Switch only; Pole 2 – Series trip overload sensing.<br>T = Poles 1 & 2 – Series trip overload sensing.<br>SS = Same as S with auxiliary switch on pole 1.<br>TS = Same as T with auxiliary switch on pole 1.<br>D = 2 Pole switching.<br>4. Rocker Color:<br>1 = Black. 2 = White. 3 = Red.  4 = Amber.  5 = Smoke.<br>5. Light (available only with White, Red, Amber and Smoke rocker colors):<br>A = 24VDC (Incandescent). B = 120VAC (Neon with resistor). C = 240VAC (Neon with resistor). N = No light.<br>6. Marking:<br>1 = International I/O. 2 = Contrasting I/O stamp (white toggle with black stamp).<br>7. Termination:<br>Q = .250” x .032” (6.35 x .813mm) quick connect / solder terminals.<br>8. Amp Rating:<br>2 5 7 10 12 15 16 20 Consult factory for availability of ratings <2A<br>**----- End of picture text -----**<br>


## **Stock Items – Authorized distributors are more likely to stock the following items.** 

W33-S1N1Q-5 W33-S4B1Q-10 W33-T4B1Q-5 W33-S1N1Q-15 W33-S4B1Q-15 W33-T4B1Q-10 W33-S1N1Q-20 W33-T2N1Q-20 W33-T4B1Q-15 

## **Outline Dimensions** 

## **Schematic** 

**==> picture [25 x 5] intentionally omitted <==**

**----- Start of picture text -----**<br>
LINE SIDE<br>**----- End of picture text -----**<br>


**==> picture [416 x 153] intentionally omitted <==**

**----- Start of picture text -----**<br>
ROCKER POLE2 POLE1<br>.980 1.724 .850<br>(24.89) (43.79) (21.59)<br>I<br>1.690<br>1.890 (42.93)<br>(48.01)<br>0 1.120<br>(28.45)<br>)<br>PANEL CLAMPING .250 LOAD SIDE<br>ARRANGEMENT .412 (6.35)<br>(10.46) NEON - AC<br>INCANDESCENT - DC<br>FITS .875 x 1.750 (22.22 x 44.45) PANEL OPENING<br>FROM .032” - .250”(.813mm - 6.35mm) THICK<br>**----- End of picture text -----**<br>


Specifications and availability subject to change. 

Dimensions are in inches over (millimeters) unless otherwise specified. 

Dimensions are shown for reference purposes only. 

www.tycoelectronics.com Technical support: 115 Refer to inside back cover.