VS2AP5CV15Q

VS2 Convergent Mode Sensor Product Manual 

## Features 

- Extremely low profile self-contained miniature sensor 

- Visible red sensing beam 

- 10 V DC to 30 V DC supply voltage 

- NPN or PNP output, depending on the model 

- 15 mm or 30 mm convergent point, depending on the model 

- Available in dark-operate or light-operate models 

## WARNING: 

- Do not use this device for personnel protection 

- • Using this device for personnel protection could result in serious injury or death. • This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition. 

## Models 

|Model(1)|Output Type|Range|
|---|---|---|
|VS2AN5CV15|NPN Light Operate|15 mm (0.6 inch) ±5 mm|
|VS2RN5CV15|NPN Dark Operate||
|VS2AP5CV15|PNP Light Operate||
|VS2RP5CV15|PNP Dark Operate||
|VS2AN5CV30|NPN Light Operate|30 mm (1.2 inch) ±10 mm|
|VS2RN5CV30|NPN Dark Operate||
|VS2AP5CV30|PNP Light Operate||
|VS2RP5CV30|PNP Dark Operate||



## Overview 

VS2 Series miniature self-contained sensors are designed for precision sensing in small areas previously accessible only to remote or fiber optic models. Typical applications include mounting inside vibrating feeders and electronic component handling equipment. 

## Wiring 

**==> picture [320 x 67] intentionally omitted <==**

**----- Start of picture text -----**<br>
NPN PNP<br>bu (3) – bn (1) +<br>10–30 V DC 10–30 V DC<br>bn (1) + bu (3) –<br>bk (4) bk (4)<br>Load Load<br>**----- End of picture text -----**<br>


## Specifications 

Supply Voltage and Current 

Supply Voltage and Current Supply Protection Circuitry 10 V DC to 30 V DC (10% max. ripple) at less than 25 mA Protected against reverse polarity and transient voltages (exclusive of load) 

- (1) Integral 2 m (6.5 ft) unterminated cable models are listed. 

   - To order the 3-pin M8 integral quick disconnect model, add the suffix "Q" to the model number. For example, VS2AN5CV15Q. 

   - • Models with a quick disconnect require a mating cordset. 

Original Instructions 07-Aug-24 

© Banner Engineering Corp. All rights reserved. 

p/n: 65411 Rev. C 

VS2 Convergent Mode Sensor Product Manual 

## Output Configuration 

SPST solid-state switch 

Choose NPN or PNP models 

Choose light operate or dark operate models 

## Output Rating 

50 mA maximum 

Off-state leakage current: < 1 microamp at 24 V DC 

On-state saturation voltage: < 0.25 V at 10 mA DC; < 0.5 V at 50 mA DC 

## Output Protection Circuitry 

Protected against output short-circuit, continuous overload, and false pulse on power-up 

Overload trip point ≥ 100 mA 

## Output Response Time 

1 millisecond ON and OFF 

NOTE: 150 millisecond delay maximum on power-up: output does not conduct during this time 

## Repeatability 

160 microseconds 

## Construction 

Black ABS housing with acrylic lens 

## Connections 

2 m (6.5 in) PVC integral cable: three #28 ga stranded conductors with PE insulation; 150 mm (6 in) PVC-jacketed cable with a 3-pin M8 male quick-disconnect connector. Quick disconnect cables are ordered separately. 

## Environmental Rating 

IP67; NEMA 6 

## Operating Conditions 

–20 °C to +55 °C (–4 °F to +131°F) 

80% at +50 °C maximum relative humidity (non-condensing) 

Vibration and Mechanical Shock Vibration and Mechanical Shock Vibration: All models meet IEC 60068-2-6, IEC 60947-5-2, UL491 Section 40, MIL-STD-202F Method 201A; 10 to 60 Hz, 0.5 mm peak to peak 

Shock: All models meet IEC 60068-2-27, IEC 60947-5-2; 30g peak acceleration, 11 millisecond pulse duration, half-sine wave pulse shape 

## Application Notes 

M2 stainless steel mounting hardware included. Optional mounting brackets are available. 

## Certifications 

## Indicators 

Two LEDs: Green and Amber 

Green ON = power to sensor is ON Green flashing = output overload 

Amber ON = light is sensed 

## Dimensions 

**==> picture [374 x 203] intentionally omitted <==**

**----- Start of picture text -----**<br>
12.0 mm<br>4b (0.47")<br>8.0 mm<br>Green Power CL (0.31") 4.7 mm<br>Indicator 3.6 mm (0.19")<br>2.0 mm (0.14")<br>Receiver ff IP<br>(0.08")<br>Amber<br>Signal Indicator 25.1 mm<br>VS2CV30  VS2CV15 (Receiver only) (0.99")<br>21.2 mm 20.6 mm<br>(0.84") (0.81") 10.9 mm<br>Emitter<br>(0.43")<br>ys ae |<br>2x ø2.2 mm<br>4.8 mm (0.09")<br>(0.19")<br>**----- End of picture text -----**<br>


page 2 of 4 

07-Aug-24 

© Banner Engineering Corp. All rights reserved. 

VS2 Convergent Mode Sensor Product Manual 

## Performance Curves 

**==> picture [500 x 403] intentionally omitted <==**

**----- Start of picture text -----**<br>
Excess Gain Curve — 15 mm Models Beam Pattern — 15 mm Models<br>1000<br>VS2CV15 VS2CV15<br>6 mm 0.24 in<br>Convergent Mode 4 mm 0.16 in<br>100 Convergent Mode<br>2 mm 0.08 in<br>0 0<br>2 mm 0.08 in<br>10 4 mm 0.16 in<br>6 mm 0.24 in<br>0 20 mm 40 mm 60 mm 80 mm 100 mm<br>1 .8 in 1.6 in 2.4 in 3.2 in 4.0 in<br>1 mm 10 mm 100 mm 1000 mm DISTANCE<br>0.04 in 0.4 in 4 in 40 in<br>DISTANCE<br>Excess Gain Curve — 30 mm Models Beam Pattern — 30 mm Models<br>1000<br>VS2CV30<br>9 mm 0.36 in<br>VS2CV30<br>6 mm 0.24 in<br>Convergent Mode<br>Convergent Mode 3 mm 0.12 in<br>100<br>0 0<br>3 mm 0.12 in<br>6 mm 0.24 in<br>10<br>9 mm 0.36 in<br>0 40 mm 80 mm 120 mm 160 mm 200 mm<br>1.6 in 3.2 in 4.8 in 6.4 in 8.0 in<br>1<br>DISTANCE<br>1 mm 10 mm 100 mm 1000 mm<br>0.04 in 0.4 in 4 in 40 in<br>DISTANCE<br>EXCESS GAIN<br>EXCESS GAIN<br>**----- End of picture text -----**<br>


## Accessories 

## Quick-Disconnect Cables 

**==> picture [500 x 153] intentionally omitted <==**

**----- Start of picture text -----**<br>
3-pin Single-Ended M8 Female Cordsets<br>Model  Length  Dimensions  Pinout (Female)<br>PKG3M-2 2 m (6.56 ft)<br>35 Typ.<br>PKG3M-4 4 m (13.12 ft)<br>PKG3M-5 5 m (16.4 ft) ø 9.5<br>4<br>PKG3M-7 7 m (22.96 ft) M8 x 1 3 1<br>PKG3M-9 9 m (29.52 ft)<br>4.3 mm Dia<br>1 = Brown<br>3 = Blue<br>4 = Black<br>PKG3M-10 10 m (32.92 ft) 7 mm<br>58 mm<br>**----- End of picture text -----**<br>


page 3 of 4 

07-Aug-24 

© Banner Engineering Corp. All rights reserved. 

VS2 Convergent Mode Sensor Product Manual 

## Brackets 

- SMBVS2RA • Right-angle bracket • Stainless steel 

- Hole center spacing: A = 80.0 Hole size: A = 3.2 x 6.0 

**==> picture [68 x 65] intentionally omitted <==**

**----- Start of picture text -----**<br>
14<br>4 X Ø2.3<br>20<br>2 X Ø3.2<br>20<br>**----- End of picture text -----**<br>


## Banner Engineering Corp Limited Warranty 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. 

For patent information, see www.bannerengineering.com/patents. 

page 4 of 4 

07-Aug-24 

© Banner Engineering Corp. All rights reserved.