VS1RP5C10

## **VS1 Series Sensors** 

## **Datasheet** 

Self-contained Miniature Sensors 

   - 10 V to 30 V dc operation 

   - Visible red or infrared sensing beam, depending on model 

1. Power ON Indicator 

• 10 mm (0.4 in) or 15 mm (0.6 in) convergent point, depending on model • NPN (sinking) or PNP (sourcing) output, and dark or light operate, depending on model • 3-wire connection; output load capacity to 50 mA • Choice of integral cable or quick-disconnect connector **WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death.** This device does not include the self-checking ° redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. 

2. Received Signal Indicator 

3. 2 m Cable or 150 mm (6 inch) Quick-Disconnect 

|**Visible Red (860 nm) Beam**<br>**Models**<br>**CONVERGENT**<br>**VISIBLE RED**<br>a|**Infrared (865 nm) Beam**<br>**Models**<br>**CONVERGENT**<br>i|**Focus**|**Output Type**|**Cable**<br>1|
|---|---|---|---|---|
|**VS1AN5CV10**|**VS1AN5C10**|10 mm (0.4 in)|NPN/LO|2 m (6.5 ft)|
|**VS1RN5CV10**|**VS1RN5C10**||NPN/DO||
|**VS1AP5CV10**|**VS1AP5C10**||PNP/LO||
|**VS1RP5CV10**|**VS1RP5C10**||PNP/DO||
|**VS1AN5CV20**|**VS1AN5C20**|15 mm (0.6 in)|NPN/LO||
|**VS1RN5CV20**|**VS1RN5C20**||NPN/DO||
|**VS1AP5CV20**|**VS1AP5C20**||PNP/LO||
|**VS1RP5CV20**|**VS1RP5C20**||PNP/DO||



## **Overview** 

VS1 Series miniature self-contained sensors are designed for precision sensing in small areas previously accessible only to remote or fiber optic models. Typical applications include mounting inside vibrating feeders and electronic component handling equipment, where larger sensors will not fit. 

The sensing energy of a convergent-mode sensor is concentrated at the specified focus point. Convergent-mode sensors are less sensitive to background reflections, compared with diffuse-mode sensors. Contact the factory if background reflections are a problem. 

1 

- 

   - To order 9 m cables models, add suffix “W/30” to the model number (e.g., VS1AN5CV10 W/30). 

- To order 150 mm (6 inch) cable with threaded 3-pin Pico-style quick disconnect fitting models, add suffix “Q” to the model number (e.g., VS1AN5CV10Q). A model with a QD connector requires a mating cable; see _Accessories_ on page 4. 

Original Document 56465 Rev. E 

18 November 2016 

56465 

VS1 Series Sensors 

## **Installation Notes** 

Included with each sensor is a hardware packet containing two stainless steel M2 × 0.4 × 16 mm Phillips pan-head machine screws, flat washers, lock washers, and hex nuts. To mount the sensor, use the supplied flat washer against the front surface of the sensor housing, between it and the screw head. If mounting to one of the optional brackets, place the lock washer against the back of the bracket, followed by the nut. If mounting directly to a threaded hole, place the lock washer between the screw head and the flat washer. 

For best results, mount the VS1 where it is protected from moisture, high humidity and dirt. 

1. Hex Nut (2) 

2. Lock Washer (2) 

3. Washer (2) 

4. M2 × 0.4 × 16 mm Phillips Pan-head Machine Screw (2) 

**==> picture [119 x 99] intentionally omitted <==**

**----- Start of picture text -----**<br>
1<br>as<br>2<br>TN 3<br>4<br>**----- End of picture text -----**<br>


## **Wiring Diagrams** 

## **NPN Outputs** 

**==> picture [349 x 78] intentionally omitted <==**

**----- Start of picture text -----**<br>
PNP Outputs Key:<br>1 = Brown<br>3 = Blue<br>3 – 1 + 4 = Black<br>1 10-30 V dc 3 10-30 V dc X = Load<br>+ –<br>4 4<br>Load Load<br>ft :<br>**----- End of picture text -----**<br>


**NOTE:** QD hookups are shown. Cabled hookups are functionally identical. 

www.bannerengineering.com - Tel: +1-763-544-3164 

P/N 56465 Rev. E 

2 

VS1 Series Sensors 

## **Specifications** 

|**Specifications**||
|---|---|
|**Supply Voltage and Current**|**Indicators**|
|10 V to 30 V dc (10% maximum ripple) at less than 25 mA (exclusive|Green ON: sensor power ON|
|of load)|Green flashing: output overload|
|**Supply Protection Circuitry**|Amber ON: light is sensed|
|Protected against reverse polarity and transient voltages|Amber flashing: marginal excess gain (1 to 1.5 times) in light condition|
|**Output Protection Circuitry**|**Construction**|
|Protected against false pulse on power-up and continuous overload or|Black ABS/polycarbonate housing with clear acrylic lens|
|short circuit of outputs. Overload trip point ≥ 100 mA.|**Environmental Rating**|
|**Output Configuration**|IEC IP54; NEMA 3|
|SPST solid-state switch|**Connections**|
|NPN (current sinking) or PNP (current sourcing), depending on model|2 m (6.5 ft) attached cable: three #28 ga stranded conductors with PE|
|Light operate (N.O.) or dark operate (N.C.), depending on model|insulation; PVC outer cable jacket; or|
|**Output Rating**<br>50 mA maximum|150 mm (6 inch) cable with 3-pin Pico-style quick-disconnect fitting.<br>QD cables are ordered separately.|
|OFF-state leakage current: < 1 microamp at 24 V dc|**Operating Conditions**|
|ON-state saturation voltage: < 0.25 V at 10 mA dc; < 0.5 V at 50 mA|−20 °C to +55 °C (−4 °F to +131°F)|
|dc|80% at +50 °C maximum relative humidity (non-condensing)|
|**Output Response Time**|**Application Notes**|
|1 millisecond ON and OFF|M2 stainless steel mounting hardware included (see Installation Notes).|
|**Repeatability**<br>250 microseconds|Optional mounting brackets are<br>available (see Accessories list).|
||**Certifications**|



## **Performance Curves** 

_Table 1: Visible Red Beam Models2_ 

||**Excess Gain**|**Excess Gain**|**Beam Pattern**|**Beam Pattern**|
|---|---|---|---|---|
|**VS1...CV10**|**1**<br>**10**<br>**100**<br>**1**<br>**0**<br>**E**<br>**X**<br>**C**<br>**E**<br>**S**<br>**S**<br>**G**<br>**A**<br>**I**<br>**N**<br>**1000**|**10 mm**<br>**0.4"**<br>**100 mm**<br>**4.0"**<br>**1000 mm**<br>**40.0"**<br>**mm**<br>**.04"**<br>**DISTANCE**<br>~~**VS1 SeriesVisible Red**~~<br>~~**10 mm Convergent Mode**~~|**0**<br>**1 mm**<br>**2 mm**<br>**3 mm**<br>**1 mm**<br>**2 mm**<br>**3 mm**|**20 mm**<br>**0.79"**<br>**16 mm**<br>**0.63"**<br>**12 mm**<br>**0.47"**<br>**8 mm**<br>**0.31"**<br>**4 mm**<br>**0.16"**<br>**0**<br>**0**<br>**0.04"**<br>**0.08"**<br>**0.12"**<br>**0.04"**<br>**0.08"**<br>**0.12"**<br>**DISTANCE**<br>~~**VS1 SeriesVisible Red**~~<br>**10 mm Convergent Mode**|
|**VS1...CV20**|**1**<br>**10**<br>**100**<br>**1**<br>**0**<br>**E**<br>**X**<br>**C**<br>**E**<br>**S**<br>**S**<br>**G**<br>**A**<br>**I**<br>**N**<br>**1000**|**10 mm**<br>**0.4"**<br>**100 mm**<br>**4.0"**<br>**1000 mm**<br>**40.0"**<br>**mm**<br>**.04"**<br>**DISTANCE**<br>~~**VS1 SeriesVisible Red**~~<br>~~**20 mm Convergent Mode**~~|**0**<br>**2 mm**<br>**4 mm**<br>**6 mm**<br>**2 mm**<br>**4 mm**<br>**6 mm**|**50 mm**<br>**2.00"**<br>**40 mm**<br>**1.60"**<br>**30 mm**<br>**1.20"**<br>**20 mm**<br>**0.80"**<br>**10 mm**<br>**0.4"**<br>**0**<br>**0**<br>**0.08"**<br>**0.16"**<br>**0.24"**<br>**0.08"**<br>**0.16"**<br>**0.24"**<br>**DISTANCE**<br>**VS1 SeriesVisible Red**<br>**20 mm Convergent Mode**|



_2 Performance based on 90% reflectance white card test_ 

P/N 56465 Rev. E 

www.bannerengineering.com - Tel: +1-763-544-3164 

3 

VS1 Series Sensors 

_Table 2: Infrared Beam Models2_ 

**==> picture [397 x 232] intentionally omitted <==**

**----- Start of picture text -----**<br>
Excess Gain Beam Pattern<br>1000<br>E VS1 Series Infrared 3 mm 0.12"<br>CX ot 10 mm Convergent Mode i 2 mm —— 0.08"<br>E 100 NE 1 mm ——— oo 0.04"<br>S Ne 0 EA 0<br>VS1...C10 GS 10 Coe oer 1 mm2 mm == 10 mm Convergent Mode VS1 Series Infrared i. 0.04"0.08"<br>A<br>NI A 3 mm ee 0.12"<br>1 {VET ALTE TTT 0 4 mm 8 mm 12 mm 16 mm ee 20 mm<br>1 mm 10 mm 100 mm 1000 mm 0.16" 0.31" 0.47" 0.63" 0.79"<br>0.04" 0.4" 4.0" 40" DISTANCE<br>DISTANCE<br>1000<br>EX 20 mm Convergent ModeVS1 Series Infrared 6 mm 0.24"<br>C 4 mm 0.16"<br>E 100 im aNGN ENE 2 mm Sa 0.08"<br>S<br>VS1...C20 GS 10 Se illea Sea 2 mm0 S 20 mm Convergent ModeVS1 Series Infrared == 00.08"<br>A 4 mm 0.16"<br>I 6 mm 0.24"<br>N 1 ABE AN | 0 10 mm 20 mm 30 mm 40 mm 50 mm<br>1 mm 10 mm 100 mm 1000 mm 0.40" 0.80" 1.20" 1.60" 2.00"<br>0.04" 0.4" 4.0" 40"<br>DISTANCE DISTANCE<br>**----- End of picture text -----**<br>


## **Dimensions** 

**==> picture [136 x 162] intentionally omitted <==**

**----- Start of picture text -----**<br>
25.7 mm<br>(1.01")<br>15 mm<br>(0.59")<br>13.5 mm 4.1 mm 8.3 mm<br>(0.53") (0.16") (0.33")<br>9.2 mm<br>ry<br>" * (0.36") 11.6 mm -<br>(0.46")<br>Ø2.2 mm<br>(0.09")<br>**----- End of picture text -----**<br>


**1** 

1. 150 mm (6 in) Cable 

## **Accessories** 

|**3-Pin Threaded M8/Pico-Style Cordsets**|**3-Pin Threaded M8/Pico-Style Cordsets**|**3-Pin Threaded M8/Pico-Style Cordsets**|**3-Pin Threaded M8/Pico-Style Cordsets**|**3-Pin Threaded M8/Pico-Style Cordsets**|
|---|---|---|---|---|
|**Model**|**Length**|**Style**|**Dimensions**|**Pinout (Female)**|
|**PKG3M-2**|2 m (6.56 ft)<br>5 m (16.40 ft)<br>7 m (22.97 ft)<br>9 m (29.53 ft)<br>10 m (32.81 ft)|Straight|**ø 9.5**<br>**35 Typ.**<br>**M8 x 1**<br>a ~~it~~<br>i Ti<br>:|**4**<br>**3**<br>**1**<br>1 = Brown<br>3 = Blue<br>4 = Black<br>ou|
|**PKG3M-5**<br>**PKG3M-7**|||||
|**PKG3M-7**<br>**PKG3M-9**|||||
|**PKG3M-10**|||||



www.bannerengineering.com - Tel: +1-763-544-3164 

P/N 56465 Rev. E 

4 

VS1 Series Sensors 

**==> picture [502 x 248] intentionally omitted <==**

**----- Start of picture text -----**<br>
Brackets<br>SMBVS1T SMBVS1TC<br>• Tall right-angle bracket • Tall right-angle compact<br>• Stainless steel bracket<br>Hole center spacing:  A = 16.8 32 • 300 stainless steel 32<br>Hole size:  A = 3.5 x 12.3 A Hole center spacing:  A = 5.5<br>Hole size:  A = ø 2.8 A<br>25 22 10 9<br>SMBVS1S SMBVS1SC<br>• Short right-angle bracket 12 • Short right-angle bracket<br>• 18-ga. stainless steel • 18-ga. stainless steel<br>Hole center spacing:  A = 16.8 A Hole center spacing:  A = 10.0 A 11<br>Hole size:  A = 3.5 x 12.3 Hole size:  A = ø 2.8<br>19.5<br>25 22 9<br>**----- End of picture text -----**<br>


## **Banner Engineering Corp. Limited Warranty** 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

**THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.** 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. **IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.** 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. 

## **Copyright Notice** 

Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. For the most recent version of any documentation, refer to: _www.bannerengineering.com_ .[©] Banner Engineering Corp. All rights reserved. 

© Banner Engineering Corp. All rights reserved