VESIM-PT

BARN NEE. 

## **VESIM-PT Sensor Interface Module** 

## **Datasheet** 

_DC-Powered Interface for VE Sensors_ 

The VESIM-PT sensor interface module is a passive DIN-rail-mount or wall-mount module. It enables remote external trigger capability. 

## **Models** 

|**Models**|**Trigger**|**Connections**|
|---|---|---|
|VESIM-PT|Current Sourcing (PNP)|Two 13-pin Terminals|



## **Features** 

**==> picture [25 x 117] intentionally omitted <==**

**----- Start of picture text -----**<br>
1<br>2<br>3<br>4<br>**----- End of picture text -----**<br>


1. Terminal Block 

2. Power LED (Green: Power on) 

3. External Trigger Button 

4. Terminal Block 

## **Terminal Block Wiring Table** 

_Table 1: Power and I/O Pinouts_ 

|**Wire Color**|**Description**|**Direction**|
|---|---|---|
|White|Discrete I/O #3|Input/Output|
|Brown|12 V dc to 30 V dc|Input|
|Green|I/O output common|-|
|Yellow|RS-232 transmit|Output|
|Gray|Discrete I/O #5|Input/Output|
|Pink|Trigger input|Input|
|Blue|Common (signal ground)|Input|
|Red|Discrete I/O #2|Input/Output|
|Orange|I/O input common|-|
|Light Blue|Discrete I/O #4|Input/Output|
|Black|Discrete I/O #1|Input/Output|
|Violet|RS-232 receive|Input|
|Bare metal|Chassis ground|-|



Original Document 193821 Rev. B 

6 April 2016 

193821 

VESIM-PT Sensor Interface Module 

## **Install the Interface Module** 

For mounting to a flat surface: 

1. Unscrew one of the end caps. 

2. Slide the DIN clips off of the housing. 

3. Replace the end cap. 

4. Position the interface module in the desired location. 

5. Insert and tighten screws through the end caps to secure the interface module in position. 

## **Specifications** 

**NOTE:** See the VE Sensor specifications for sensor data, available at _www.bannerengineering.com_ . 

## **Input Supply Voltage** 

## **Connections** 

12 to 30 V dc **Terminal Strip:** Accepts 12 to 24 gauge wire 

**Adjustments Operating Conditions** External PNP Trigger button **Temperature:** 0 °C to +50 °C (+32 °F to +122 °F) **Humidity:** 90% maximum relative humidity (non-condensing) 

## **Construction** 

PCB circuit board; plastic housing, end caps, and DIN rail mounting **Weight** hardware Approximately 135 grams (0.3 lb) 

**Environmental Rating** IEC IP00 NEMA 1 

## **Dimensions** 

All measurements are listed in millimeters [inches], unless noted otherwise. 

**==> picture [345 x 171] intentionally omitted <==**

**----- Start of picture text -----**<br>
49.5 mm<br>127.5 mm (1.95")<br>(5.02")<br>29.5 mm<br>2X 2.7 mm  (1.16")<br>(0.11")<br>2X R 2.7 mm<br>(R 0.11") a<br>| fa) = — 4<br>86.4 mm<br>P}} (3.40")<br>[0] a a !<br>43.2 mm<br>(1.70")<br>ee \ e |<br>2X 11.8 mm<br>(0.46")<br>103.7 mm  17.5 mm<br>(4.08") (0.69")<br>137.6 mm<br>(5.42")<br>**----- End of picture text -----**<br>


## **Banner Engineering Corp. Limited Warranty** 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

**THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.** 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. **IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.** 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. 

www.bannerengineering.com - Tel: +1-763-544-3164 

more sensors, more solutions