UWX1C100MCL2GB

**ALUMINUM  ELECTROLYTIC  CAPACITORS** 

## **UWX** 

5.5mmL Chip Type 

Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Load life of 2000 hours at 85°C. 

Compliant to the RoHS directive (2011/65/EU). **UWT UWJ** High High Values marked with an in the dimension table Temperature Temp reflow are scheduled to be discontinued and are not recommended for new designs. **UWX** Bi-polarized **UWP** —_e Smaller <e ; Specifications **UZS** Item Performance Characteristics ~~Se~~ Category Temperature Range –40 to +85°C Rated Voltage Range 4 to 50V ~~Oo~~ Rated Capacitance Range 0.1 to 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C ~~ot~~ Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) 4 6.3 10 16 25 35 50 tan  δ (MAX.) 0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 0.16 (0.19) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Values in (    ) applicable to WR, φ3 case size. ~~SS~~ Measurement frequency : 120Hz ~~eee~~ Rated voltage (V) 4 6.3 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C 7 4 3 2 2 2 2 ZT / Z20 (MAX.) Z–40°C / Z+20°C 15 8 8 4 4 3 3 ~~ae~~ The specifications listed at right shall be met Capacitance change Within ±20% of the initial capacitance value (Within ±25% for 4 V and φ3,WR series units) Endurance when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at tan δ 200% or  less than the initial specified value 85°C. Leakage Current Less than or equal to the initial specified value ~~|~~ Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. ~~= = ee CLE~~ Resistance to soldering The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the Catan pδacitance change Within ±10% of the initial caLess than or equal to the initial spacitance valuepecified value heat characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Leakage current Less than or equal to the initial specified value ~~|~~ Marking Black print on the case top. ~~S~~ 

Chip Type 

**==> picture [233 x 149] intentionally omitted <==**

**----- Start of picture text -----**<br>
Positive<br>Capacitance<br>: 2 Lot No. [ 1 Voltage Plastic platform<br>C±0.2<br>0.3 MAX.<br>;<br>< i + Al<br>5.4 +0.1–0.2 0.5 to 0.8<br>I A, Negative<br>(mm)<br>φD 3 4 5 6.3 8<br>A 1.5 1.8 2.1 2.4 3.3<br>B 3.3 4.3 5.3 6.6 8.3<br>C 3.3 4.3 5.3 6.6 8.3<br>E 0.8 1.0 1.3 2.2 2.3<br>0.5 MAX.<br>A±0.2<br>A2 10 16V D±0.5φ B±0.2 EA±0.2<br>**----- End of picture text -----**<br>


**==> picture [214 x 156] intentionally omitted <==**

**----- Start of picture text -----**<br>
Type numbering system (Example : 16V 10µF)<br>1 2 3 4 5 6 7 8 9 10 11 12 13 14<br>U W X 1 C 1 0 0 M C L 1 G B<br>Taping code<br>CoCo Size code<br>Configuration φD Code<br>Capacitance tolerance (±20%) 3 2<br>4 to 8 1<br>Rated capacitance (10µF)<br>Rated voltage (16V)<br>Series name<br>Type<br>• [In the case of size ][φ][3 in (   ),parentheses, use WX in the 2nd and 3rd]<br>2 digit and put a in the 12th digit of type numbering system.<br>**----- End of picture text -----**<br>


1.  Voltage mark for 6.3V is   6V  . 

In case of marking for φ3 units,  “V” for rated voltage is omitted. 

2.  In case of marking for φ3 units,  Lot No.is expressed by a digit (month code). 

Dimension table in next page. 

104 | 

Lo CAT.8100E 

**ALUMINUM  ELECTROLYTIC  CAPACITORS** 

## **UWX** 

## Dimensions 

**==> picture [511 x 257] intentionally omitted <==**

**----- Start of picture text -----**<br>
V 4 6.3 10 16 25 35 50<br>Cap. (µF) Code 0G 0J 1A 1C 1E 1V 1H<br>    0.1 0R1 4 (3)  1.0<br>    0.22 R22 4 (3)  2.0<br>    0.33 R33 4 (3)  2.8<br>    0.47 R47 4 (3)  4.0<br>    1 010 [4 (3)] 8.4(8.0)<br>    2.2 2R2  3  8.4       4 (3) 13 (10)<br>    3.3 3R3  3  10    4  17<br>    4.7 4R7 4 (3)  16 (12)  4  18 5  20 (18)<br>  10 100 4 (3)  23     18( ) 5  27 (24) 5  29 (24) 6.3  33 (30)<br>  22 220 3 019 4 (3)  28 (21) 5  33 (30) 5  37 (30) 6.3  42 (38) 6.3  46 (39) 8  52 (43)<br>  33 330 4 028 5  37 (34) 5  41 (34) 6.3  49 (44) 6.3  52 (46) 8  62 (53) 8  71<br>  47 470 4 033 5  45 (40) 6.3  52 (47) 6.3  58 (52) 8  70 (60)  8 80<br>  56 560 5 042 6.3  52 (46) 6.3  57 (50) 6.3  63 (57) 8  76 (65)<br>100 101 5 056 6.3  70 (47) 6.3  76 (54) 6.3  86 8  110<br>150 151     6.3 079 6.3  71 8  111 (76)<br>220 221     6.3 096 8  110 (74)  8  135 Case size Rated<br>330 331 8 145 8  170 φ D(mm) ripple<br> (   ) is also available with φ3mm upon request. Rated ripple current (mArms) at 85°C 120Hz<br>• [In the case of size ][φ][3 in (   ),parentheses, use WX at 2nd and 3rd digit and put] 2 at the 12th digit of type numbering system.  (   ) = φ3 units and UWR<br>Size φ4 is available for capacitors marked.   "    "<br>Size φ5 is available for capacitors marked.   "    "  In such a case,    W R  will be put at 2nd and 3rd digit of type numbering system.<br>Size φ6.3 is available for capacitors marked.   "    " }<br>**----- End of picture text -----**<br>


## Frequency coefficient of rated ripple current 

|Frequency|50 Hz|120 Hz|300 Hz|1 kHz|10 kHz or more|
|---|---|---|---|---|---|
|Coefficient|0.70|1.00|1.17|1.36|1.50|



Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. 

Please select UUR(p.148), UUG(p.156)  if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. 

CAT.8100E 

105