UWT1V470MCL1GS

**ALUMINUM  ELECTROLYTIC  CAPACITORS** 

## **UWT** 

Chip Type, Wide Temperature Range 

Chip type operating over wide temperature range of to –55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). 

**==> picture [22 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
UWZ<br>**----- End of picture text -----**<br>


**==> picture [103 x 41] intentionally omitted <==**

**----- Start of picture text -----**<br>
High<br>Temperature<br>Reflow<br>UWF  Lowimpeadance<br>UWT<br>**----- End of picture text -----**<br>


**UUT** Long Life Smaller to} **UZT** 

## Specifications 

|Item<br>~~Fe~~<br>~~ne~~|Performance Characteristics<br>~~Fe~~|
|---|---|
|CategoryTemperature Range<br>~~Fe~~<br>~~ne~~<br>~~Re~~|–55 to +105°C<br>~~Fe~~|
|Rated Voltage Range<br>~~ne~~<br>~~Re~~<br>~~a~~|4 to 50V|
|Rated Capacitance Range<br>~~Re~~<br>~~a~~<br>~~a~~|1 to 1500µF|
|Capacitance Tolerance<br>~~a~~<br>~~a~~|±20% at 120Hz,20°C|
|Leakage Current<br>~~a~~|After 2 minutes' application of rated voltage,  leakage current is not more than 0.01CV or 3(µA),  whichever isgreater.|
|Tangent of loss angle (tanδ)<br>~~oe~~|Measurement frequency : 120Hz at 20°C<br>Rated voltage(V)<br>tanδ(MAX.)<br>4<br>0.40<br>6.3<br>0.30<br>10<br>0.24<br>16<br>0.20<br>25<br>0.16<br>35<br>0.14<br>50<br>0.14<br>~~oe~~|
|Stability at Low Temperature<br>~~oe~~|Measurement frequency : 120Hz<br>Z–25°C / Z+20°C<br>Z–40°C / Z+20°C<br>Rated voltage(V)<br>Impedance ratio<br>ZT / Z20 (MAX.)<br>4<br>7<br>15<br>6.3<br>4<br>8<br>10<br>3<br>8<br>16<br>2<br>4<br>25<br>2<br>4<br>35<br>2<br>3<br>50<br>2<br>3<br>~~oe~~|
|Endurance|The specifications listed at right shall be<br>met when the capacitors are restored to<br>20°C after the rated voltage is applied for<br>1000 hours at 105°C.<br>Capacitance<br>change<br>Leakage current<br>tanδ<br>Within ±25% of the initial capacitance value for capacitors ofφ3mm unit,  and 16V or less.<br>Within ±20% of the initial capacitance value for capacitors of 25V or more.<br>200% or less than the initial specified value<br>Less than or equal to the initial specified value|
|Shelf Life|After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4<br>clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.|
|Resistance to soldering<br>heat<br>~~a~~<br>~~a~~|The capacitors are kept on a hot plate for 30 seconds, which<br>is maintained at 250°C. The capacitors shall meet the<br>characteristic requirements listed at right when they are<br>removed from theplate and restored to 20°C.<br>Capacitance change<br>Leakage current<br>tanδ<br>Within ±10% of the initial capacitance value<br>Less than or equal to the initial specified value<br>Less than or equal to the initial specified value|
|Marking<br>~~a~~<br>~~a~~|Black print on the case top.|



## Chip Type 

Type numbering system  (Example : 16V 10µF) 

**==> picture [509 x 221] intentionally omitted <==**

**----- Start of picture text -----**<br>
(φ3 to φ8 × 5.4 ) Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 φD code<br>Capacitance " 1 Plastic platform U W T 1 C 1 0 0 M C L 1 G B 3 to 8 (5.4L) GB<br>105˚C Marking Voltage 0.3 MAX. C±0.2 6.3 to 10 (L    5.8)Package codeGS<br>Size code<br>Configuration φD code<br>© - : ogc coo Capacitance tolerance (±20%) φD code 3 2<br>Rated capacitance (10µF) 3 to 8 (L   7.7) CL 4 to 10 1<br>Lot No. oO 2 (L±0.3)L +0.1–0.2 3 H ice Negative KS Rated voltage (16V) 8 to 10 (L = 10) NL<br>Series name<br>3 Apply to φ6.3 × 5.8, φ6.3 × 7.7<br>a Se Type<br>(φ8 × 10,  φ10 × 10 ) Positive<br>Capacitance (mm)<br>105Trade mark˚C Marking Voltage1 Plastic platform0.3 MAX. C±0.2 φD × L 3 × 5.4 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4 8 × 10 10 × 10<br>A 1.5 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2<br>B 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3<br>- Rew) L±0.5 H ee C 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3<br>Lot No. Pressure relief vent a SS Negative i E 0.8 OO 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5<br>= Pp | | | | | | ff<br>L 5.4 5.4 5.4 5.4 5.8 7.7 5.4 10 10<br>ee<br>. ee ee ee<br>1.  Voltage mark for 6.3V is   6V .  In case of marking for  φ3 units,  “V” for ratedφ3 units,  “V” for rated3 units,  “V” for rated H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1<br>0.5 MAX.<br>A±0.2<br>E<br>A2P 10 16V D±0.5φ B±0.2 A±0.2<br>0.5 MAX.<br>A±0.2<br>E<br>A2P 100 35V D±0.5φ B±0.2 A±0.2<br>**----- End of picture text -----**<br>


1.  Voltage mark for 6.3V is   6V .  In case of marking for  φ3 units,  “V” for ratedφ3 units,  “V” for rated3 units,  “V” for rated voltage is omitted. 2.  In case of marking for  φ3 units. Lot No is expressed by a digit (month code). 

eo Dimension table in next page. 

110 | 

CAT.8100F ~~—~~ 

**ALUMINUM  ELECTROLYTIC  CAPACITORS** 

## **UWT** 

## Dimensions 

|V<br>Code<br>Cap.(µF)|V<br>Code<br>Cap.(µF)|**4**|**4**|**6.3**|**6.3**|**10**|**10**|**16**|**16**|**25**|**25**|**35**|**35**|**50**|**50**|
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|||0G||0J||1A||1C||1E||1V||1H||
|**1**|010|||||||||||||4×5.4(3)|6.3 (5.9)|
|**2.2**|2R2|||||||||||3×5.4|7.5|4×5.4(3)|11 (9)|
|**3.3**|3R3|||||||||||3×5.4|9|4×5.4|14|
|**4.7**|4R7|||||||||4×5.4(3)|13(10)|4×5.4|15|5×5.4|19|
|**10**|100|||||||4×5.4(3)|18(14)|5×5.4|23|5×5.4|25|6.3×5.4|30|
|**22**|220|4×5.4|22|4×5.4|22|5×5.4|27|5×5.4|30|6.3×5.4|38|6.3×5.4|42|8×5.4|51(45)|
|**33**|330|5×5.4|30|5×5.4|30|5×5.4|35|6.3×5.4|40|6.3×5.4|48|8×5.4|59 (52)|6.3×7.7<br>|60|
|**47**|470|5×5.4|36|5×5.4|36|6.3×5.4|46|6.3×5.4|50|8×5.4|66(59)|6.3×5.8|63|6.3×7.7|63|
|**100**|101|6.3×5.4|60|6.3×5.4|60|6.3×5.4|60|6.3×5.4|<br>60|6.3×7.7|91|6.3×7.7|84|8×10|140|
|**150**|151|6.3×5.8|86|6.3×5.8|86|6.3×5.8|86|6.3×7.7|95|8×10|140|8×10|155|10×10|180|
|**220**|221|8×5.4|102(91)|8×5.4|102(91)|6.3×7.7<br>|105|6.3×7.7|105|8×10|155|8×10|190|10×10|220|
|**330**|331|6.3×7.7|105|6.3×7.7|105|8×10<br>|195|8×10|195|8×10|190|10×10|300|||
|**470**|471|8×10|210|8×10|210|8×10<br>|210|8×10|<br>230|10×10|300|||||
|**680**|681|8×10|210|8×10|210|10×10<br>|310|10×10|310|||||||
|**1000**|102|8×10|230|8×10|230|10×10<br>|310|||||||Case size<br>φD×L (mm)|Rated<br>ripple|
|**1500**|152|10×10|310|10×10|310|||||||||||



(   ) is also available with φ3mm upon request.  In such a case, 2 will be put at 12th digit of type numbering system. 

Rated ripple current (mArms) at 105°C 120Hz 

Size φ6.3 × 5.8 is available for capacitors marked.   " "   In such a case, 6 will be  put at 12th digit of type numbering system. 

## Frequency coefficient of rated ripple current 

|Frequency|50 Hz|120 Hz|300 Hz|1 kHz|10 kHz or more|
|---|---|---|---|---|---|
|Coefficient|0.70|1.00|1.17|1.36|1.50|



Taping specifications are given in page 23. 

Recommended land size, soldering by reflow are given in page 18, 19. 

Please select UUX(p.152), UUJ(p.158) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. 

CAT.8100F 

111