UUT1A101MCL1GS

**ALUMINUM  ELECTROLYTIC  CAPACITORS** 

## **UUT** 

6mmL Chip Type,  Wide Temperature Range 

Chip type with load life 2000 hours at +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). Values marked with an in the dimension table are scheduled to be **UUA** Long Life discontinued and are not recommended **UUT** Long Life **UWT** for new designs. **UUX** an. Higher C/V | ¥ Specifications & Item Performance Characteristics ~~sh~~ Category Temperature Range –55 to +105°C Rated Voltage Range 4 to 50V ~~ot~~ Rated Capacitance Range 0.1 to 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. ~~LN~~ Measurement frequency :120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) 4 6.3 10 16 25 35 50 tan  δ (MAX.) 0.37 0.28 0.24 0.20 0.16 0.13 0.12 ~~eee~~ Measurement frequency :120Hz Rated voltage (V) 4 6.3 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C 6 3 3 2 2 2 2 ZT / Z20 (MAX.) Z–40°C / Z+20°C 12 8 5 4 3 3 3 ~~a __—_———_——_-ee~~ The specifications listed at right shall be met Capacitance Within ±25% of the initial capacitance value (16V or less) Endurance when the capacitors are restored to 20°C after change Within ±20% of the initial capacitance value (25V or more) the rated voltage is applied for 2000 hours at tan δ 200% or less than the initial specified value 105°C. Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 ~~a~~ clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value Resistance to soldering maintained at 250°C. The capacitors shall meet the characteristic tan δ Less than or equal to the initial specified value heat requirements listed at right when they are removed from the plate and restored to 20°C. Leakage current Less than or equal to the initial specified value Marking Black print on the case top. ~~eee~~ 

> Chip Type Type numbering system  (Example : 16V 10µF) 105°C Marking Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U U T 1 C 1 0 0 M C L 1 G S Capacitance Plastic platform Lot No. Voltage 0.3MAX. C±0.2 (mm) Taping code 

> φD 4 5 6.3 Configuration A 1.8 2.1 2.4 Capacitance tolerance (±20%) B 4.3 5.3 6.6 Rated capacitance (10μF) C 4.3 5.3 6.6 E 1.0 1.3 2.2 Rated voltage (16V) ~~“~~ | 0.5 to 0.8 ~~Mel~~ Series name ~~“S~~ h ~~t~~ g 5.8±0.3 g ~~ees||~~ Negative Type 

> Voltage mark for 6.3V is   6V  . - ~~| +~~ h-X ~~5~~ Dimensions 

> V **4 6.3 10 16 25 35 50** Cap.(µF) Code 0G 0J 1A 1C 1E 1V 1H ~~SS~~ **0.1** 0R1 ~~ee~~ 4 1.0 **0.22** R22 4 2.6 ~~ee~~ **0.33** R33 4 3.2 **0.47** R47 4 3.8 ~~re~~ **1** 010 ~~eee ee eee eee~~ 4 6.2 **2.2** 2R2 4 11 ~~————————~~ **3.3** 3R3 4 14 **4.7** 4R7 4 13 4 15 5 19 ~~—————_——————~~ **10** 100 4 18 5 23 5 25 6.3 30 **22** 220 4 22 4 22 5 27 5 30 6.3 38 6.3 42 ~~a~~ **33** 330 5 30 5 30 5 35 6.3 40 6.3 48 **47** 470 5 36 5 36 6.3 46 6.3 50 AllowableRated **100** 101 6.3 60 6.3 60 6.3 60 Case sizeφ D (mm) rippleripple ~~———ae~~ Rated ripple current (mArms) at 105°C 120Hz 

Frequency coefficient of rated ripple current Taping specifications are given in page 23. Frequency 50 Hz 120 Hz 300 Hz 1 kHz      10 kHz or more Recommended land size, soldering by reflow are given in page 18, 19. Please select UUX(p.152), UUJ(p.158) if high C/V products are required. Coefficient 0.70 1.00 1.17 1.36 1.50 ~~ee e~~ Please refer to page 3 for the minimum order quantity. ~~e~~ | 117 [ CAT.8100E