ULP442M035DBF1A0

**Type ULP, 2 and 3 mm Ultra Low Profile Aluminum Electrolytic Capacitor, 85 ºC High Energy Density, REACH Compliant** 

At 2 and 3 mm thin, type ULP offers the highest energy density available in a low profile aluminum electrolytic.    It’s ideal for the lowest profile circuits where high capacitance is needed for bulk storage. Look to type ULP to replace arrays of SMT solid tantalum capacitors. 

## **Highlights** 

-  2 or 3 mm profile - High energy density .4 J/cc - Replaces banks of solid tantalum chips - 3000 hr life @ 85 ºC without voltage derating - REACH Compliant 

## **Specifications** 

|**Specifications**||
|---|---|
|**Temperature Range**|–40 °C to 85 °C, at 100% rated voltage|
|**Surge Voltage**|120% of the rated working Vdc|
|**Capacitance Range**|500 μF to 24,000 μF|
|**Capacitance Tolerance**|±20%  at 120 Hz and 25 °C|
|**DC Leakage Current**|After a five minute application of the rated working voltage at +25 °C :<br>ɪ≤ 0.001CV|
|**Moisture Resistance**|After 500 hours storage at +60°C and 90% to 95% RH with or without load, the<br>capacitor will meet the following limits:<br>∆C = +20%/–20% of the initial measured value.<br>ESR ≤ the initial specified value<br>DCL ≤ the initial specified value|
|**DC Life Test**|Apply rated DC working voltage at 85°C for 3000 hours, and then stabilize<br>them to +25°C.<br>Capacitors will meet the following limits:<br>ΔC = ±20% of the initial measured value<br>ESR ≤ the initial specified value<br>DCL ≤ the initial specified value|
|**Shelf Life Test**|Shelf life is typically 5 to 10 years.  Accelerated test:<br>After 500 hours at 85°C, capacitors will meet the initial limits after stabilization<br>at 25°C.|
|**Vibration**<br>_Mounting: Vibration capability is dependent upon mounting restraint. To_<br>_achieve the high vibration levels as published on right, additional mounting_<br>_restraint is required._|MIL-STD-202, Meth. 204, Sine Swept, IEC 60068-2-6 Standard ULP: 10g|
|**Low Temperature Characteristics**|Impedence Ratio Z-40 º/ Z+25 ºC @120 Hz<br>≤ 10 (4 Vdc - 10 Vdc)<br>≤ 4 (16 Vdc - 63 Vdc)|
|**Altitude**|60,000  feet max|



**CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800** 

**Type ULP, 2 and 3 mm Ultra Low Profile Aluminum Electrolytic Capacitor, 85 ºC** 

|**Vibration Test**|**Level**<br>The specimens, while deenergized or operating under the load conditions<br>specifed, shall be subjected to the vibration amplitude, frequency range,<br>and duration specifed for each case size.<br>**Amplitude**<br>The specimens shall be subjected to a simple harmonic motion having an<br>amplitude of either 0.06-inch double amplitude (maximum total excursion)<br>or peak level specifed above, whichever is less. The tolerance on vibration<br>amplitude shall be ±10 percent.<br>**Frequency Range**<br>The vibration frequency shall be varied logarithmically between the<br>approximate limits of 10 to 2,000 Hz.<br>**Sweep Time and Duration**<br>The entire frequency range of 10 to 2,000 Hz and return to 10 Hz shall be<br>traversed in 20 minutes. This cycle shall be performed 12 times in each<br>of three mutually perpendicular directions (total of 36 times), so that<br>the motion shall be applied for a total period of approximately 12 hours.<br>Interruptions are permitted provided the requirements for rate of change<br>and test duration are met.|
|---|---|
|**Typical Weight**|Case DA - 17g, Case DB - 22g|
|**Terminals**|Flexible printed circuit 16 Amps for 1 second Max  (ɪ2t = 250 A2s)|
|**Case Material**|Cu/Ni/Zn (nickel - silver)|



**CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800** 

## **Type ULP, 2 and 3 mm Ultra Low Profle Aluminum Electrolytic Capacitor, 85 ºC** 

## **Part Numbering System** 

**==> picture [552 x 89] intentionally omitted <==**

**----- Start of picture text -----**<br>
ULP 243 M 4R0 DB F2 A 0<br>Type Capacitance Tolerance Rated Voltage Case Lead Mounting Style Insulation<br>ULP 243 = 24,000 µF ±20% 4R0 = 4.0 Vdc DA = 42 x  62 x 2 mm F1 = Flex - 20pin (20 x 21 mm) A = None 0 = None<br>016 = 16 Vdc DB = 42 x  62 x 3 mm F2 = Flex - 20pin (42 x 21 mm) 1 = Polywrap<br>**----- End of picture text -----**<br>


## **Outline Drawing** 

**==> picture [534 x 330] intentionally omitted <==**

**----- Start of picture text -----**<br>
  2x 10.5mm±1<br>  31mm±1<br>  21mm     42mm<br>  1.9mm<br>20mm±1(F1)<br>42mm±1(F2)<br>  62mm<br>A<br>   1-9  = Negative<br>Pin 1 10,11 = NC<br>2.2mm Max (DA Case) 12-20 = Positive<br>3.2mm Max (DB Case)<br>Mating Connector<br>(Molex 0522712079 or equivalent)<br>DETAIL A<br>SCALE 2 : 1<br>**----- End of picture text -----**<br>


**CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800** 

**Type ULP, 2 and 3 mm Ultra Low Profile Aluminum Electrolytic Capacitor, 85 ºC** 

## **Ratings** 

|**Voltage**|**Cap (µF)**|**Catalog Part Number**|**ESR max**<br>**25 °C mΩ**<br>**120 Hz**|**ESR max**<br>**Surge**<br>**25 ºC Vdc**|
|---|---|---|---|---|
|**2 mm**|||||
|**4**<br>7,800<br>ULP782M4R0DAF1A0<br>210<br>4.8<br>**6.3**<br>6,600<br>ULP662M6R3DAF1A0<br>210<br>7.56<br>**10**<br>5,200<br>ULP522M010DAF1A0<br>210<br>12<br>**16**<br>3,600<br>ULP362M016DAF1A0<br>210<br>19.2<br>**25**<br>2,300<br>ULP232M025DAF1A0<br>210<br>30|||||
|**35**<br>1,400<br>ULP142M035DAF1A0<br>210<br>42<br>**50**<br>700<br>ULP701M050DAF1A0<br>210<br>60<br>**63**<br>500<br>ULP501M063DAF1A0<br>420<br>75.6|||||
|**3 mm**|||||
|**4**<br>24,000<br>ULP243M4R0DBF1A0<br>80<br>4.8<br>**6.3**<br>20,000<br>ULP203M6R3DBF1A0<br>80<br>7.56<br>**10**<br>15,000<br>ULP153M010DBF1A0<br>80<br>12<br>**16**<br>11,000<br>ULP113M016DBF1A0<br>80<br>19.2<br>**25**<br>6,900<br>ULP692M025DBF1A0<br>80<br>30|||||
|**35**<br>4,400<br>ULP442M035DBF1A0<br>80<br>42<br>**50**<br>2,200<br>ULP222M050DBF1A0<br>80<br>60<br>**63**<br>1,500<br>ULP152M063DBF1A0<br>160<br>75.6|||||



## **Typical Performance Curves** 

**CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800** 

**Type ULP, 2 and 3 mm Ultra Low Profile Aluminum Electrolytic Capacitor, 85 ºC** 

## **Typical Performance Curves** 

**CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800** 

**Notice and Disclaimer:** All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements  (“Cornell Dubilier”) has of  operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of  any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained.  Although Cornell Dubilier strives to apply  the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required.