SLB300S48K

## **SL POWER SLB300 SERIES** 

300 Watts Single Output Medical & Industrial Grade 

Advanced Energy’s SL Power SLB300 medically-approved AC-DC power supplies are available with a nominal main output of 12 V, 15 V, 18 V, 24 V, 36 V, 48 V or 56 V. SLB300 power supplies provide up to 300 Watts with air flow. All models have output overvoltage, short circuit and overload protection and a 3 x 5 x 1.22 inch form factor. 

## **AT A GLANCE** 

## **Total Power** 

**300 Watts** 

## **Input Voltage** 

**80 to 264 VAC** 

**# of Outputs** 

**Single** 

## **SPECIAL FEATURES** 

>  190 Watts Convection 

- 300 Watts with 100 LFM Airflow 

## **SAFETY** 

   - EN/CSA/IEC/UL62368-1 

   - EN/CSA/IEC/UL60601-1-1, 3rd Ed 

- 3” x 5” x 1.22” Form Factor 

- Universal Input 80 to 264 VAC 

- For 1U Applications 

- Class B Conducted and Radiated EMI 

- 3 Years Warranty 

- RoHS Compliant 

©2023 Advanced Energy Industries, Inc. 

**SLB300** 

## **ELECTRICAL SPECIFICATIONS** 

|**Input**|**Input**|
|---|---|
|Input ra nge|80 to 264 VAC, 47 to 63 Hz, 1Ø. 120 to 370 VDC|
|Earth leakage current|<300 μA @ 264 VAC, 60 Hz, NC; <600 μA SFC|
|Efficiency|92% typical|
|Isolation voltage (Class I version)|Input/Ground: 1800 VAC (1 MOPP)<br>Output/Ground: 1800 VAC (1 MOPP)|
|Isolation voltage (Class II version)|Input/Output: 4300 VAC (2 MOPP)|
|**Output**||
|Maximum power|Max of 190 Watts for convection cooled, 300 Watts with 100 LFM air flow. See "Ordering Information" section<br>for specific voltage model ratings|
|Output voltage|See "Ordering Information" section|
|Voltage adjustability|Fixed output|
|Ripple and noise|0.5% RMS, 1% pk-pk for all models. See "Ordering Information" section for details. (20 MHz bandwidth,<br>differential mode. Measured with noise probe directly across output terminals, and load terminated with<br>0.1μF ceramic and 10μF low ESR capacitors)|
|Total regulation|±3% (combined line, load and initial setting)|
|Minimum load|Not required|
|Switching frequency|PFC: fixed, 65 kHz. Main Converter: variable 35 to 200 kHz, 65 to 70 kHz at full load|
|Transient response|500 μs response time for return to within 0.5% of final value for a 50% load step change,∆i/∆t<0.2 A/μs. Max.<br>voltage deviation is ±3%|
|Hold-up time|16 ms at 190 W, 120 VAC, 60Hz|
|Turn on time|<3 s @ 115 VAC, full load|
|**Reliability**||
|MTBF|250K hours, 25°C, 110 VAC|
|**Protection**||
|Overvoltage protection|Latch mode. See "Ordering Information" for trip range.|
|Short circuit protection|Short across the output terminals will not cause damage to the unit. Hiccup mode. Auto recovery.|
|Thermal protection|Will shutdown upon an over temperature condition.|
|Overload protection|130% to 180% of rated output current value. Hiccup mode.|



## **DERATING CURVE** 

Notes: 190 W convection cooled and 300 W continuous with 100 LFM airflow, derate output power to 50% at 70°C. 

Notes: Tested at 300 LFM airflow. Other values available upon request. 

**2 advancedenergy.com** 

**SLB300** 

## **ORDERING INFORMATION** 

**==> picture [479 x 137] intentionally omitted <==**

**----- Start of picture text -----**<br>
With Air Flow Convection Conduction<br>Model Output<br>Fan Output<br> Number Voltage Output Output Output Output Output Output<br>Current  Power  Current  Power  Current  Power<br>SLB300S12x   12 V 22.5 A 270 W 15.4 A 185 W 15.4 A 185 W<br>SLB300S15x   15 V 20.0 A 300 W 12.7 A 190 W 12.7 A 190 W<br>SLB300S18x   18 V 16.7 A 300 W 10.6 A 190 W 10.6 A 190 W Custom<br>modifications<br>SLB300S24x   24 V 12.5 A 300 W 7.9 A 190 W 7.9 A 190 W<br>available upon<br>SLB300S36x   36 V 8.3 A 300 W 5.3 A 190 W 5.3 A 190 W request<br>SLB300S48x   48 V 6.3 A 300 W 4.0 A 190 W 4.0 A 190 W<br>SLB300S56x 56 V 5.4 A 300 W 3.4 A 190 W 3.4 A 190 W<br>**----- End of picture text -----**<br>


Notes: 

1. Consult factory for availability of all models as some models will be part of the initial product release. 

2. Total convection power is 190 Watts. 

## **EMI/EMC COMPLIANCE** 

**==> picture [479 x 200] intentionally omitted <==**

**----- Start of picture text -----**<br>
Conducted emissions EN55011/22/32 Class B, FCC Part 15, Subpart B, Class B<br>Radiated emissions  EN55011/22/32 Class A, FCC Part 15, Subpart B, Class A w/6db margin<br>Harmonic current emissions EN61000-3-2, Class A<br>Voltage fluctuations & flicker IEC61000-3-3<br>Static Discharge Immunity EN55024/IEC61000-4-2, Level 4: ±8kV contact, ±15kV air, Crit. A; IEC60601-1-2,<br>Electro static discharge immunity<br>4th Ed. Table 4<br>Radiated RF immunity  EN55022/EN61000-4-3, 10V/m, 80MHz-2.7GHz, 80% AM at 1kHz; IEC60601-1-2, 4th Edition, Table 4<br>Electrical fast transients / bursts EN55024/IEC61000-4-4, Level 4, ±4kV, 100Khz rep rate, 40A, Criteria A; IEC60601-1-2, 4th Edition, Table 5<br>EN55024/IEC61000-4-5, Level 4, ±2kV DM, ±4kV CM, Criteria A; Surpasses IEC60601-1-2, 4th Ed.<br>Surge susceptibility<br>requirements.<br>EN55022/IEC61000-4-6, 3V/m – Level 4, 0.15 to 80Mhz; and 12V/m in ISM and amateur radio bands<br>Conducted RF susceptibility<br>between 0.15Mhz and 80Mhz, 80% AM at 1KHz; IEC60601-1-2, 4th Edition, Table 5.<br>Power frequency magnetic fields test EN55024/IEC1000-4-8, Level 4: 30A/m, 50/60 Hz; IEC60601-1-2, 4th Edition, Table 4<br>EN55024/IEC/EN61000-4-11: 100% dip for 10 ms, at 0, 45, 90, 135, 180, 225, 270 and 315 degrees; 100%<br>Voltage dip immunity dip for 20ms, 0 deg., Crit. A; 100% dip for 5000ms (250/300 cycles), Crit. B; 60% dip for 100ms, Criteria B;<br>30% dip for 500ms, Crit. A; IEC60601-1-2, 4th Edition, Table 5<br>**----- End of picture text -----**<br>


Notes: 

Performance criteria are based on EN55024. According to the standards, performance criteria are decoded as following: 

- A. Normal performance during and after the test 

- B. Temporary degradation, self-recoverable 

- C. Temporary degradation, operator intervention required to recover the operation 

- D. Permanent damage 

**advancedenergy.com       3** 

**SLB300** 

## **ENVIRONMENTAL SPECIFICATIONS** 

**==> picture [479 x 118] intentionally omitted <==**

**----- Start of picture text -----**<br>
Operating: 0.003g2/Hz, 1.5grms overall, 3 axes, 10 min/axis<br>Vibration Non-operating: 0.026g2/Hz, 5.0grms overall, 3 axes, 1 hr/axis<br>Operating: Half-sine, 20gpk, 10ms, 3 axes, 6 shocks total<br>Shock<br>Non-operating: Half-sine, 40 gpk, 10ms, 3 axes, 6 shocks total<br>Operating temperature  -10°C to +70°C. Start up at -40°C, Full load<br>Temperature derating Derate output power linearly above 40°C to 50% at 70°C<br>Storage temperature  -40°C to +85°C<br>Altitude Operating: -500 to 15,000 ft (5000 m). Non-operating: -500 to 40,000 ft<br>Relative humidity 5% to 95%, non-condensing<br>**----- End of picture text -----**<br>


## **PIN ASSIGNMENTS** 

**==> picture [479 x 192] intentionally omitted <==**

**----- Start of picture text -----**<br>
Type  Connector Pin Assignments Mating Connector<br>TE# 640445-3 PIN 1 AC Neutral TE/AMP# 640250-3<br>J100 (Input connector, Class II)<br>(1 pin removed) PIN 3 AC Line Pins: 640252-1<br>J101 (Ground, Class I only)23 AMP 1217125-1 - Functional Ground (FG) MOLEX# 19002-0001<br>PIN 1 RTN<br>PIN 2 RTN<br>PIN 3 RTN<br>PIN 4 +Vo MOLEX# 39-01-2105<br>MOLEX# PIN 5 +Vo Or<br>J300 (Output connector) CviLux# CP-01110030<br>87427 (2x5) PIN 6 RTN<br>Pins: CP-01100106-HC<br>PIN 7 RTN<br>PIN 8 +Vo<br>PIN 9 +Vo<br>PIN 10 +Vo<br>**----- End of picture text -----**<br>


Notes: 

1. Contact AE for other compatible connector options. 

2. For Class I: the power supply should be mounted on a conducted plate for better EMI performance. 

3. FG is safety ground connection, Class I only. 

4. This power supply requires mounting on standoffs 0.20” (5mm) minimum in height. 

**4 advancedenergy.com** 

**SLB300** 

## **MECHANICAL DRAWING** 

Notes: 

1. All dimensions in mm (inches). 

2. Mounting holes should be grounded for EMI purpose. 

3. FG is safety ground connection. 

4. This power supply requires mounting on metal standoffs 0.20” (5mm) min. in height. 

5. Dimensions: W: 3.0” x L: 5.0” x H: 1.22” 

6. Weight: 370 g. 

**advancedenergy.com       5** 

**==> picture [596 x 270] intentionally omitted <==**

## **ABOUT ADVANCED ENERGY** 

Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. 

Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. 

## **TRUST** 

For international contact information, visit advancedenergy.com. 

powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 

Specifications are subject to change without notice. Not responsible for errors or omissions. ©2023 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, and AE® are U.S. trademarks of Advanced Energy Industries, Inc. 

ENG-SLB300-04.27.23