RID-85A

**- RID 85 series** 

85W Dual Output Switching Power Supply Caen eee e eee eee e rere reer rere errr 

## ■ 

* 100% . full load burn-in. test ℃ 

℃ 

|**MODEL**<br>**RID-85A**<br>**RID-85B**<br>**DC VOLTAGE**<br>**RATED CURRENT**<br>**CURRENT RANGE**<br>**Note.3**<br>**RATED POWER**<br>**Note.6**<br>**OUTPUT**<br>**VOLTAGE ADJ. RANGE**<br>**SETUP, RISE TIME**<br>**HOLD UP TIME (Typ.)**<br>**VOLTAGE RANGE**<br>**FREQUENCY RANGE**<br>**EFFICIENCY(Typ.)**<br>**AC CURRENT (Typ.)**<br>**INPUT**<br>**INRUSH CURRENT (Typ.)**<br>**LEAKAGE CURRENT**<br>**SAFETY STANDARDS**<br>**WORKING TEMP.**<br>**WORKING HUMIDITY**<br>**STORAGE TEMP., HUMIDITY**<br>**TEMP. COEFFICIENT**<br>**VIBRATION**<br>**MTBF**<br>**DIMENSION**<br>**OTHERS**<br>**NOTE**<br>**PACKING**<br>**OVERLOAD**<br>**OVER VOLTAGE**<br>5V<br>12V<br>CH2<br>5V<br>CH1<br>24V<br>CH2<br>8A<br>4A<br>8A<br>2A<br>0 ~ 10A<br>0 ~ 5A<br>0 ~ 10A<br>0 ~ 2.5A<br>88W<br>88W<br>80mVp-p<br>120mVp-p<br>80mVp-p<br>120mVp-p<br>CH1: 4.75 ~ 5.5V<br>CH1: 4.75 ~ 5.5V<br>±2.0%<br>±8.0%<br>±2.0%<br>±5.0%<br>±0.5%<br>±1.0%<br>±0.5%<br>±1.0%<br>±1.0%<br>±3.0%<br>±1.0%<br>±5.0%<br>500ms, 20ms/230VAC          1200ms, 30ms/115VAC at full load<br>100ms/230VAC          18ms/115VAC at full load<br>88 ~ 264VAC          125 ~ 373VDC (Withstand 300VAC surge for 5sec. Without damage)<br>47 ~ 63Hz<br>80%<br>81%<br>CH1: 5.75 ~ 6.75V<br>2.5A/115VAC          1.5A/230VAC<br>COLD START 50A/230VAC<br><2mA / 240VAC<br>110 ~ 150% rated output power<br>Protection type : Hiccup mode, recovers automatically after fault condition is removed<br>UL62368-1, TUV EN62368-1<br>approved<br>,EAC TP TC 004<br>Compliance to EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020<br>Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020<br>-25 ~ +70<br>(Refer to "Derating Curve")<br>℃<br>20 ~ 90% RH non-condensing<br>-40 ~ +85<br>, 10 ~ 95% RH<br>℃<br>±<br>℃<br>℃<br>0.03%/<br>(0 ~ 50<br>)on +5V output<br>10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes<br>239.4Khrs min.      MIL-HDBK-217F (25<br>)<br>℃<br>159*97*38mm (L*W*H)<br>℃<br>(as available on http://www.meanwell.com)<br>℃<br>℃<br>※<br>：<br>https://www.meanwell.com/serviceDisclaimer.aspx<br>0.6Kg; 24pcs/15.4Kg/0.83CUFT<br>Protection type : Hiccup mode, recovers automatically after fault condition is removed<br>**RIPPLE & NOISE (max.) Note.2**<br>**VOLTAGE TOLERANCE Note.3**<br>**LINE REGULATION**<br>**Note.4**<br>**LOAD REGULATION**<br>**Note.5**<br>**WITHSTAND VOLTAGE**<br>**ISOLATION RESISTANCE**<br>I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC<br>I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25<br>/ 70% RH<br>℃<br>**ENVIRONMENT**<br>**PROTECTION**<br>**SAFETY &**<br>**EMC**<br>**(Note 7)**<br>CH1<br>**OUTPUT NUMBER**<br>**EMC IMMUNITY**<br>**EMC EMISSION**<br>1. All parameters NOT specially mentioned are measured at230VAC input, rated load and 25<br>of ambient temperature.<br>2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.<br>3. Tolerance: includes set up tolerance, line regulation and load regulation. (In order to meet tolerance, it is recommended that CH1 load > 20% rated current.)<br>4. Line regulation is measured from low line to high line at rated load.<br>5. Load regulation is measured from 20% to 100% rated load, and other output at60% rated load.<br>6. Each output can work within current range. But total output power can't exceed rated output power.<br>7. The power supply is considered a componentwhich will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on<br>a360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to<br>perform these EMC tests, please refer to “EMI testing of component power supplies.”<br>8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.<br>9. The ambient temperature derating of 3.5<br>/1000m with fanless models and of<br>5<br>/1000m with fan models for operating altitude higher than 2000m(6500ft).<br>10<br>his power supply does not meet the harmonic current requirements outlined by EN61000-3-2. Please do not use this power supply<br>under the following conditions:<br>a) the end-devices is used within the European Union, and<br>b) the end-devices is connected to public mains supply with 220Vac or greater rated nominal voltage, and<br>c) the power supply is:<br>- installed in end-devices with average or continuous input power greater than 75W, or<br>- belong to part ofa lighting system<br>Exception:<br>Power supplies used within the following end-devices do not need to fulfill EN61000-3-2<br>a) professional equipment with a total rated input power greater than 1000W;<br>b) symmetrically controlled heating elements with a rated power less than or equal to 200W<br>Product Liability Disclaimer<br>For detailed information, please refer to|**MODEL**<br>**RID-85A**<br>**RID-85B**<br>**DC VOLTAGE**<br>**RATED CURRENT**<br>**CURRENT RANGE**<br>**Note.3**<br>**RATED POWER**<br>**Note.6**<br>**OUTPUT**<br>**VOLTAGE ADJ. RANGE**<br>**SETUP, RISE TIME**<br>**HOLD UP TIME (Typ.)**<br>**VOLTAGE RANGE**<br>**FREQUENCY RANGE**<br>**EFFICIENCY(Typ.)**<br>**AC CURRENT (Typ.)**<br>**INPUT**<br>**INRUSH CURRENT (Typ.)**<br>**LEAKAGE CURRENT**<br>**SAFETY STANDARDS**<br>**WORKING TEMP.**<br>**WORKING HUMIDITY**<br>**STORAGE TEMP., HUMIDITY**<br>**TEMP. COEFFICIENT**<br>**VIBRATION**<br>**MTBF**<br>**DIMENSION**<br>**OTHERS**<br>**NOTE**<br>**PACKING**<br>**OVERLOAD**<br>**OVER VOLTAGE**<br>5V<br>12V<br>CH2<br>5V<br>CH1<br>24V<br>CH2<br>8A<br>4A<br>8A<br>2A<br>0 ~ 10A<br>0 ~ 5A<br>0 ~ 10A<br>0 ~ 2.5A<br>88W<br>88W<br>80mVp-p<br>120mVp-p<br>80mVp-p<br>120mVp-p<br>CH1: 4.75 ~ 5.5V<br>CH1: 4.75 ~ 5.5V<br>±2.0%<br>±8.0%<br>±2.0%<br>±5.0%<br>±0.5%<br>±1.0%<br>±0.5%<br>±1.0%<br>±1.0%<br>±3.0%<br>±1.0%<br>±5.0%<br>500ms, 20ms/230VAC          1200ms, 30ms/115VAC at full load<br>100ms/230VAC          18ms/115VAC at full load<br>88 ~ 264VAC          125 ~ 373VDC (Withstand 300VAC surge for 5sec. Without damage)<br>47 ~ 63Hz<br>80%<br>81%<br>CH1: 5.75 ~ 6.75V<br>2.5A/115VAC          1.5A/230VAC<br>COLD START 50A/230VAC<br><2mA / 240VAC<br>110 ~ 150% rated output power<br>Protection type : Hiccup mode, recovers automatically after fault condition is removed<br>UL62368-1, TUV EN62368-1<br>approved<br>,EAC TP TC 004<br>Compliance to EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020<br>Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020<br>-25 ~ +70<br>(Refer to "Derating Curve")<br>℃<br>20 ~ 90% RH non-condensing<br>-40 ~ +85<br>, 10 ~ 95% RH<br>℃<br>±<br>℃<br>℃<br>0.03%/<br>(0 ~ 50<br>)on +5V output<br>10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes<br>239.4Khrs min.      MIL-HDBK-217F (25<br>)<br>℃<br>159*97*38mm (L*W*H)<br>℃<br>(as available on http://www.meanwell.com)<br>℃<br>℃<br>※<br>：<br>https://www.meanwell.com/serviceDisclaimer.aspx<br>0.6Kg; 24pcs/15.4Kg/0.83CUFT<br>Protection type : Hiccup mode, recovers automatically after fault condition is removed<br>**RIPPLE & NOISE (max.) Note.2**<br>**VOLTAGE TOLERANCE Note.3**<br>**LINE REGULATION**<br>**Note.4**<br>**LOAD REGULATION**<br>**Note.5**<br>**WITHSTAND VOLTAGE**<br>**ISOLATION RESISTANCE**<br>I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC<br>I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25<br>/ 70% RH<br>℃<br>**ENVIRONMENT**<br>**PROTECTION**<br>**SAFETY &**<br>**EMC**<br>**(Note 7)**<br>CH1<br>**OUTPUT NUMBER**<br>**EMC IMMUNITY**<br>**EMC EMISSION**<br>1. All parameters NOT specially mentioned are measured at230VAC input, rated load and 25<br>of ambient temperature.<br>2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.<br>3. Tolerance: includes set up tolerance, line regulation and load regulation. (In order to meet tolerance, it is recommended that CH1 load > 20% rated current.)<br>4. Line regulation is measured from low line to high line at rated load.<br>5. Load regulation is measured from 20% to 100% rated load, and other output at60% rated load.<br>6. Each output can work within current range. But total output power can't exceed rated output power.<br>7. The power supply is considered a componentwhich will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on<br>a360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to<br>perform these EMC tests, please refer to “EMI testing of component power supplies.”<br>8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.<br>9. The ambient temperature derating of 3.5<br>/1000m with fanless models and of<br>5<br>/1000m with fan models for operating altitude higher than 2000m(6500ft).<br>10<br>his power supply does not meet the harmonic current requirements outlined by EN61000-3-2. Please do not use this power supply<br>under the following conditions:<br>a) the end-devices is used within the European Union, and<br>b) the end-devices is connected to public mains supply with 220Vac or greater rated nominal voltage, and<br>c) the power supply is:<br>- installed in end-devices with average or continuous input power greater than 75W, or<br>- belong to part ofa lighting system<br>Exception:<br>Power supplies used within the following end-devices do not need to fulfill EN61000-3-2<br>a) professional equipment with a total rated input power greater than 1000W;<br>b) symmetrically controlled heating elements with a rated power less than or equal to 200W<br>Product Liability Disclaimer<br>For detailed information, please refer to|**RID-85A**|**RID-85A**|**RID-85B**|**RID-85B**|
|---|---|---|---|---|---|
||**OUTPUT NUMBER**|CH1|CH2|CH1|CH2|
||**DC VOLTAGE**|5V|12V|5V|24V|
||**RATED CURRENT**|8A|4A|8A|2A|
||**CURRENT RANGE**<br>**Note.3**|0 ~ 10A|0 ~ 5A|0 ~ 10A|0 ~ 2.5A|
||**RATED POWER**<br>**Note.6**|88W||88W||
||**RIPPLE & NOISE (max.) Note.2**|80mVp-p|120mVp-p|80mVp-p|120mVp-p|
||**VOLTAGE ADJ. RANGE**|CH1: 4.75 ~ 5.5V||CH1: 4.75 ~ 5.5V||
||**VOLTAGE TOLERANCE Note.3**|±2.0%|±8.0%|±2.0%|±5.0%|
||**LINE REGULATION**<br>**Note.4**|±0.5%|±1.0%|±0.5%|±1.0%|
||**LOAD REGULATION**<br>**Note.5**|±1.0%|±3.0%|±1.0%|±5.0%|
||**SETUP, RISE TIME**|500ms, 20ms/230VAC          1200ms, 30ms/115VAC at full load||||
||**HOLD UP TIME (Typ.)**|100ms/230VAC          18ms/115VAC at full load||||
||**VOLTAGE RANGE**|88 ~ 264VAC          125 ~ 373VDC (Withstand 300VAC surge for 5sec. Without damage)||||
||**FREQUENCY RANGE**|47 ~ 63Hz||||
||**EFFICIENCY(Typ.)**|80%||81%||
||**AC CURRENT (Typ.)**|2.5A/115VAC          1.5A/230VAC||||
||**INRUSH CURRENT (Typ.)**|COLD START 50A/230VAC||||
||**LEAKAGE CURRENT**|<2mA / 240VAC||||
||**OVERLOAD**|110 ~ 150% rated output power<br>Protection type : Hiccup mode, recovers automatically after fault condition is removed||||
||**OVER VOLTAGE**|CH1: 5.75 ~ 6.75V<br>Protection type : Hiccup mode, recovers automatically after fault condition is removed||||
||**WORKING TEMP.**|-25 ~ +70<br>(Refer to "Derating Curve")<br>℃||||
||**WORKING HUMIDITY**|20 ~ 90% RH non-condensing||||
||**STORAGE TEMP., HUMIDITY**|-40 ~ +85<br>, 10 ~ 95% RH<br>℃||||
||**TEMP. COEFFICIENT**|±<br>℃<br>℃<br>0.03%/<br>(0 ~ 50<br>)on +5V output||||
||**VIBRATION**|10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes||||
||**SAFETY STANDARDS**|UL62368-1, TUV EN62368-1<br>approved<br>,EAC TP TC 004||||
||**WITHSTAND VOLTAGE**|I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC||||
||**ISOLATION RESISTANCE**|I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25<br>/ 70% RH<br>℃||||
||**EMC EMISSION**|Compliance to EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020||||
||**EMC IMMUNITY**|Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020||||
||**MTBF**|239.4Khrs min.      MIL-HDBK-217F (25<br>)<br>℃||||
||**DIMENSION**|159*97*38mm (L*W*H)||||
||**PACKING**|0.6Kg; 24pcs/15.4Kg/0.83CUFT||||
||℃<br>(as available on http://www.meanwell.com)<br>℃<br>℃<br>※<br>：<br>https://www.meanwell.com/serviceDisclaimer.aspx<br>1. All parameters NOT specially mentioned are measured at230VAC input, rated load and 25<br>of ambient temperature.<br>2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.<br>3. Tolerance: includes set up tolerance, line regulation and load regulation. (In order to meet tolerance, it is recommended that CH1 load > 20% rated current.)<br>4. Line regulation is measured from low line to high line at rated load.<br>5. Load regulation is measured from 20% to 100% rated load, and other output at60% rated load.<br>6. Each output can work within current range. But total output power can't exceed rated output power.<br>7. The power supply is considered a componentwhich will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on<br>a360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to<br>perform these EMC tests, please refer to “EMI testing of component power supplies.”<br>8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.<br>9. The ambient temperature derating of 3.5<br>/1000m with fanless models and of<br>5<br>/1000m with fan models for operating altitude higher than 2000m(6500ft).<br>10<br>his power supply does not meet the harmonic current requirements outlined by EN61000-3-2. Please do not use this power supply<br>under the following conditions:<br>a) the end-devices is used within the European Union, and<br>b) the end-devices is connected to public mains supply with 220Vac or greater rated nominal voltage, and<br>c) the power supply is:<br>- installed in end-devices with average or continuous input power greater than 75W, or<br>- belong to part ofa lighting system<br>Exception:<br>Power supplies used within the following end-devices do not need to fulfill EN61000-3-2<br>a) professional equipment with a total rated input power greater than 1000W;<br>b) symmetrically controlled heating elements with a rated power less than or equal to 200W<br>Product Liability Disclaimer<br>For detailed information, please refer to|||||



## **SPECIFICATION** 

**NOTE** 

“EMI testing of component power supplies.” (as available on http://www.meanwell.com) first start. Turning ON/OFF the power supply very quickly may lead to increase of the ℃ /1000m with fanless models and of 5 ℃ /1000m with fan models for operating altitude 

※ Product Liability Disclaimer ： 

https://www.meanwell.com/serviceDisclaimer.aspx 

_File Name:RID-85-SPEC   2021-03-12_ 

**- RID 85 series** 

## 85W Dual Output Switching Power Supply 

**==> picture [511 x 668] intentionally omitted <==**

**----- Start of picture text -----**<br>
Mechanical Specification Case No. 901C     Unit:mm<br>152.5<br>1<br>2<br>3<br>4<br>5<br>6<br>7<br>4.5<br>24 78<br>159<br>6.5 150<br>Terminal Pin No. Assignment<br>Pin No. Assignment Pin No. Assignment<br>1 AC/L 5 DC OUTPUT +V2<br>2 AC/N 6 DC OUTPUT G1<br>3 FG 7 DC OUTPUT +V1<br>4 DC OUTPUT G2<br>22 117<br>Block Diagram fosc : 60KHz<br>RECTIFIERS<br>+V2<br>&<br>COM2<br>FILTER<br>EMI RECTIFIERS POWER RECTIFIERS +V1<br>I/P FILTER & SWITCHING & COM1<br>FILTER FILTER<br>DETECTION<br>FG<br>CIRCUIT<br>O.L.P. CONTROL<br>O.V.P.<br>Derating Curve Static Characteristics<br>100<br>100<br>90<br>80<br>80<br>60 70<br>60<br>40<br>50<br>20<br>40<br>-25 0 10 20 30 40 50 60 70 (VERTICAL) 88 95 100 115 120 140 160 180 200 220 240 264<br>AMBIENT TEMPERATURE ( ℃ ) INPUT VOLTAGE (VAC) 60Hz<br>3.5<br>ψ<br>2-M3<br>3-M3<br>ψ<br>3.5<br>LOAD (%) LOAD (%)<br>3.5<br>9.5<br>65<br>84.5 97<br>8.2<br>18.5<br>18 3.5 28.5 38<br>7<br>9 9<br>**----- End of picture text -----**<br>


_File Name:RID-85-SPEC   2021-03-12_