RCL175PQ47-C

**175 Watts** 

xppower.com 

## **RCL Series** 

- 200 W Peak Rating 

- Up to 120 W Convection-cooled 

- IT, Industrial and Medical Safety Approvals 

- Class I & Class II Installations 

- Single, Dual, Triple and Quad Outputs 

- Connector & Mechanical Options 

- 3 Year Warranty 

## **Sp** ~~**ecification**~~ 

## **Input** 

- Input Voltage • 85-264 VAC (120-370 VDC) (see note 3) Input Frequency • 47-63 Hz; 400 Hz[(1)] Input Current • 2.1 A max at 115 VAC 0.9 A max at 230 VAC 

- Inrush Current • 17 A max at 115 VAC, 35 A max at 230 VAC, cold start at +25 °C 

- Power Factor • >0.9 Earth Leakage Current • 120 μ A max at 115 VAC / 50 Hz 200 μ A max at 230 VAC / 50 Hz 

- Input Protection • Internal T3.15 A/250 V in line and neutral 

## **Output** 

- Output Voltage • See models and ratings table and note 2 Output Voltage Trim • ±10% output 1, outputs 2-4 track by same percentage 

- Initial Set Accuracy • ±1% of nominal at 50% load Minimum Load • See models & ratings table Start Up Delay • 2 s max Start Up Rise Time • 100 ms max Hold Up Time • 20 ms min at nominal low line & max power Drift • <±0.2% after 20 mins warm up Line Regulation • ±0.5% of nominal over full input range Load Regulation • PQ42 & 43: V1 & V2 ±3%, V3 & V4 ±5% of nominal, all other models: V1 ±1%, V2, V3 & V4 ±5% of nominal 

- Transient Response • 4% max deviation, recovery to within 1% in 500 μ s for a 25% load change at 1 A/ μ s 

- Ripple & Noise • 50 mV (Vo ≤ 5 V), 120 mV (Vo = 12, 15 V), 200 mV (Vo = 24, 48 V). Measured pk-pk with a 20 MHz bandwidth 

- Overvoltage Protection • 115-140% on V1 only, recycle input to reset 

- Overtemperature • Fitted with auto restart Protection Overload Protection • 110-125% - Primary side power limiting with auto recovery. Constant current limit for single output models and foldback current limit for multi output models. V3 & V4 PTC resetting fuses 

Temperature • 0.02%/°C Coefficient 

## ~~**Notes**~~ 

_1. Safety approvals cover frequency 47-63 Hz._ 

## **General** 

- Efficiency • 80-90% depending on model Isolation • 4000 VAC Input to Output 2 x MOPP (1 x MOPP Class II), 1500 VAC Input to Ground, 1 x MOPP 1500 VAC Output to Ground open frame 500 VAC Output to Ground U channel & covered 

- Switching Frequency • PFC 75 kHz typical, PWM 60 kHz typical Signals • Power fail - open collector output referenced to 0 V sense 

- Remote Sense • See application notes Remote On/Off • See application notes MTBF • 385 kHrs typical to MIL-HDBK-217F at 25 °C, GB 

- Power Density • 7.1 W/in[3] 

## **Environmental** 

- Operating Temperature • -10 °C to +50 °C at full power, derate to 50% power at +70 °C 

- Operating Humidity • 5-95% RH, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 3000 m Shock • 30 g peak, half sine, 6 axes Vibration • 2 g rms, 5-500 Hz, 3 axes 

## **EMC & Safety** 

- Emissions • EN55011/32 class B conducted, class A radiated 

- Harmonic Currents • EN61000-3-2 class A EN61000-3-2 class C for loads ≥ 20% 

- Voltage Flicker • EN61000-3-3 ESD Immunity • EN61000-4-2, level 3 Perf Criteria A Radiated Immunity • EN61000-4-3, 10 V rms 80% mod, Perf Criteria A 

- EFT/Burst • EN61000-4-4, level 3 Perf Criteria A Surge • EN61000-4-5, installation class 3 Perf Criteria A 

- Conducted Immunity • EN61000-4-6, level 3 Perf Criteria A Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B EN60601-1-2, 30% 500 ms, 60% 100 ms, 100% 10 ms, 100% 5000 ms, Perf Criteria A, A, A, B - 230 VAC Contact sales for 115 V operation 

- Safety Approvals • EN60601-1, ANSI/AAMI ES60601-1, CSA22.2 No.60601-1 per cUL, Including Risk Management, UL62368-1, EN62368-1, CE & UKCA meets all applicable directives & legislation 

**RCL175** 

## ~~**Models and Ratings**~~ 

|Total Power|Total Power|Total Power|Output 1|Output 1|Output 1|Output 1|Output 2(5,6)|Output 2(5,6)|Output 2(5,6)|Output 2(5,6)|Output 3(6,8)|Output 3(6,8)|Output 3(6,8)|Output 4(6,8)|Output 4(6,8)|Output 4(6,8)|Model Number|
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|Max(7)<br>~~Pp~~<br>~~|~~|Peak(1)|Conv.(4,5)|V|Min|Max(4,5)|Peak(1)|V|Min|Max|Peak(1)|V|Min|Max|V|Min|Max||
|175 W<br>~~Pp~~<br>~~|~~<br>~~pT~~|204 W<br>~~pT~~|120 W|12.0 V|0.0 A|14.5 A|17.0 A|||||||||||RCL175PS12|
|175 W<br>~~Pp~~<br>~~|~~<br>~~pT~~<br>~~poTT~~|195 W<br>~~pT~~<br>~~TT~~|120 W<br>~~TT~~|15.0 V|0.0 A|11.6 A|13.0 A|||||||||||RCL175PS15|
|175 W<br>~~pT~~<br>~~poTT~~<br>~~P~~~~**p**TCT~~|200 W<br>~~pT~~<br>~~TT~~<br>~~TCT~~|120 W<br>~~TT~~<br>~~TCT~~|24.0 V|0.0 A|7.2 A|8.3 A|||||||||||RCL175PS24|
|175 W<br>~~po TT~~<br>~~P~~~~**p**TCT~~|200 W<br>~~TT~~<br>~~TCT~~|120 W<br>~~TT~~<br>~~TCT~~|28.0 V|0.0 A|6.2 A|7.1 A|||||||||||RCL175PS28|
|175 W<br>~~P~~~~**p** TCT~~<br>~~pT~~|202 W<br>~~TCT~~<br>~~pT~~|120 W<br>~~TCT~~|48.0 V|0.0 A|3.6 A|4.2 A|||~~o~~|~~o~~|~~o~~|~~o~~|~~o~~|~~o~~|~~o~~|~~o~~|RCL175PS48<br>~~o~~|
|175 W<br>~~pT~~|200 W<br>~~pT~~|110 W|+5.0 V|1.5 A|15.0 A|-|+12.0 V|0.1 A|8.3 A|10.4 A|||||||RCL175PD22|
|175 W<br>~~pT~~<br>~~pT~~|200 W<br>~~pT~~<br>~~pT~~|110 W<br>|+5.0 V<br>|1.5 A<br>|15.0 A<br>|-<br>|+12.0 V<br>|0.1 A<br>|6.3 A<br>|8.4 A<br>|F 12 V<br>|0.1 A<br>|2.0 A<br>||||RCL175PT31<br>|
|175 W<br>~~pT~~|200 W<br>~~pT~~|110 W<br>~~pT~~|+5.0 V<br>~~pT~~|1.5 A<br>~~pT~~|15.0 A<br>~~pT~~|-<br>~~pT~~|+15.0 V<br>~~pT~~|0.1 A<br>~~pT~~|4.6 A<br>~~pT~~|6.6 A<br>~~pT~~|F 15 V<br>~~pT~~|0.1 A<br>~~pT~~|2.0 A<br>~~pT~~|~~pT~~|~~pT~~|~~pT~~|RCL175PT32<br>~~pT~~|
|175 W<br>~~pT~~<br>~~pT~~|200 W<br>~~pT~~<br>~~pT~~|90 W|+5.0 V|1.5 A|15.0 A|-|+12.0 V|0.1 A|5.5 A|7.6 A|F 5 V|0.1 A|2.0 A|F 12 V|0.1 A|2.0 A|RCL175PQ44|
|175 W<br>~~pT~~<br>~~**p**ot~~|200 W<br>~~pT~~<br>~~ot~~|90 W|+5.0 V|1.5 A|15.0 A|-|+15.0 V|0.1 A|4.0 A|6.0 A|F 5 V|0.1 A|2.0 A|F 15 V|0.1 A|2.0 A|RCL175PQ45|
|175 W<br>~~pT~~<br>~~**p**ot~~|200 W<br>~~pT~~<br>~~ot~~|90 W|+5.0 V|1.5 A|15.0 A|-|+24.0 V|0.1 A|3.2 A|5.0 A|F 12 V|0.1 A|2.0 A|F 12 V|0.1 A|2.0 A|RCL175PQ46|
|175 W<br>~~**p**ot~~|200 W<br>~~ot~~|90 W|+5.0 V|1.5 A|15.0 A|-|+24.0 V|0.1 A|3.0 A<br>~~o~~|5.0 A<br>~~o~~|F 15 V<br>~~o~~|0.1 A<br>~~o~~|2.0 A<br>~~o~~|F 15 V<br>~~o~~|0.1 A<br>~~o~~|2.0 A<br>~~o~~|RCL175PQ47<br>~~o~~|



## ~~**Notes**~~ 

_1. Peak rating can be taken for 5 seconds in every minute. Average power not to exceed maximum power._ 

_2. User-accessible fan supply rated at 12 V at 350 mA (not available on fan-cooled units)._ 

_3. For operation at 85 VAC output power is derated to 95%._ 

_4. Output 1 10 A max convection-cooled._ 

   _6. A minimum load of 100 mA is required on output 2, 3 and 4 to maintain the regulation figures._ 

   _7. 12 CFM airflow required for maximum power._ 

   _8. Outputs 3 & 4 are floating, they can be connected externally for positive or negative output._ 

   _9. Connector kits and cable harnesses available. Consult sales for options._ 

_5. 20 A max from output 1 and 2 combined convection-cooled._ 

## ~~**Pin Connectors**~~ 

||INPUT CONNECTOR - P1|INPUT CONNECTOR - P1|
|---|---|---|
|Pin||Function|
|1||Live|
|2||N/C|
|3||Neutral|



P1 is a 3-way 0.156" pitch square pin header Molex housing 09-91-0300 pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) 

|OUTPUT CONNECTOR - P2|OUTPUT CONNECTOR - P2|
|---|---|
|Molex P/No. 26-60-4060 - Single Ouput<br>Molex P/No. 26-60-4120 - Dual Ouput<br>Molex P/No. 26-60-4140 - Triple Output +PD22<br>Molex P/No. 26-60-4160 - Quad Ouput||
|Pin|Function|
|1|+Output 1|
|2|+Output 1|
|3|+Output 1|
|4|0 V|
|5|0 V|
|6|0 V|
|7|0 V|
|8|0 V|
|9|0 V|
|10|+Output 2|
|11|+Output 2|
|12|+Output 2|
|13|-Output 3|
|14|+Output 3|
|15|-Output 4|
|16|+Output 4|



P3 is a 6-way 0.1" pitch square pin header Molex housing 22-01-2065 pins 08-50-0032 (30-22 AWG) 

## ~~**Application Notes**~~ 

Remote Sense - Power Fail - Remote On/Off - 

V1 only, compensates for 0.5 V or 10% whichever is lower. 

Open collector output referenced to 0 V sense (when using the power fail signal, -Sense must be connected to 0 V). 

Connect pin 1 (P3) to 0 V to disable unit (optional remote enable specify suffix ‘-E’ with the model number). Applying a logic ‘0’ will also disable the unit. 

## ~~**Options**~~ 

- For U-channel version, add suffix ‘-U’ to the model number. 

- For U-channel version with cover kit, add suffix ‘-C’ to the model number. 

- For U-channel version with fan cover kit, add suffix ‘-F’ to the model number. 

- For screw terminals (output connector P2 only). Contact Sales. 

- For versions with remote enable. Contact Sales. 

- For foldback current limit on single output models, contact sales. 

- For constant current limit (output 1 & 2) on multi-output models, contact sales. 

## ~~**Connector Information**~~ 

For all formats, output connector P2 mating halves: 

Single Output Models: Molex housing 09-50-3061 or equivalent Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) 

## Dual Output Models: 

Molex housing 09-50-3221 or equivalent (except model PD22 which has a 14-way connector) Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) 

Triple Output Models: 

Molex housing 09-50-3141 or equivalent Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) 

Quad Output Models: Molex housing 09-50-3161  or equivalent Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) 

For mating connectors, use pinouts as detailed in this datasheet. May not match manufacturers mold marks on connector. 

**RCL175** 

## ~~**Mechanical Details**~~ 

## **Open Frame** 

**==> picture [514 x 178] intentionally omitted <==**

**----- Start of picture text -----**<br>
5.50<br>(139.7)<br>Pin 16 Voltage Adj.<br>Beto. ANDNIA<br>Ø 0.14 (3.5) Pin 6<br>3.70 3.26 Mounting hole  1.28 P3<br>(93.9) (82.9) P2 (4 positions) (32.4) Pin 1<br>1<br>P1<br>3<br>0.10<br>Pin 1 (2.5)<br>Earth/Safety Ground Tag (Class I Operation) Notes<br>0.22(5.5) 5.23 1. Suitable for class I and class II operation, for class II<br>(132.7) applications contact sales.<br>**----- End of picture text -----**<br>


2. All dimensions are in inches (mm) 

3. Weight: 1.10 lbs (500 g) approx. 

4. Tolerance ±0.02 (0.5) 

5. Overall height: 1.36 (34.6). 

## **U-channel** 

**==> picture [460 x 288] intentionally omitted <==**

**----- Start of picture text -----**<br>
5.71<br>(145.0)<br>0.89 3.94<br>0.24 5.23 (22.5) (100.0)<br>(6.2) (132.7) 0.47<br>(12.0)<br>Pin 16 8-32 UNC Mounting hole (in 4 positions)<br>+ BAU gga °<br>Ø 0.14 (3.5)<br>3.90 3.26 Mounting hole  2.95<br>(99.0) (82.8) @ ae P2 (4 positions) (75.0)<br>1<br>P1 3 M3 Mounting hole (in 4 positions)<br>Pin 1<br>Earth/Safety Ground Tag<br>1.18 3.35 M3 Mounting hole<br>(30.0) (85.0) (in 2 positions each side)<br>0.55 4.60<br>(14.1) (116.8)<br>1.50 Notes<br>(38.1)<br>0.74 1. Suitable for class I operation only.<br>(18.7)<br>\ 2. All dimensions are in inches (mm)<br>3. Weight: 1.54 lbs (700 g) approx.<br>| scr (40.8)1.60 (63.5)2.50 ee 8-32 UNC Mounting hole 4. Tolerance ±0.02 (0.5)<br>(in 2 positions each side)<br>**----- End of picture text -----**<br>


5. Mounting screws must not penetrate by more than 0.12” (3.0 mm) max 

**RCL175** 

## ~~**Mechanical Details**~~ 

## **U-channel & Cover** 

**==> picture [517 x 286] intentionally omitted <==**

**----- Start of picture text -----**<br>
5.71<br>(145.0)<br>0.24 5.23 0.89 3.94<br>(6.1) (132.7) 0.47 (22.5) (100.0)<br>(12.0)<br>= = ne 737 =<br>Pin 16<br>8-32 UNC Mounting hole<br>(in 4 positions)<br>Ø 0.14 (3.5)<br>3.90 3.26 ‘i Mounting hole  2.95 el<br>(99.0) (82.9) P2 (4 positions) (75.0)<br>1<br>P1 3 M3 Mounting hole<br>(in 4 positions)<br>et ol Pin 1<br>es<br>Earth/Safety Ground Tag M3 Mounting hole<br>(in 2 positions each side) 0.55 4.60<br>1.18 3.35 (14.1) (116.8)<br>(30.0) (85.0)<br>Notes<br>1. Suitable for class I operation only.<br>1.59 2. All dimensions are in inches (mm)<br>(40.4)<br>0.74 3. Weight: 1.76 lbs (800 g) approx.<br>(1.87) 4. Tolerance ±0.02 (0.5)<br>5. Mounting screws must not penetrate by<br>1.60 2.50 8-32 UNC Mounting hole(in 2 positions each side) more than 0.12” (3.0 mm) max.<br>(40.8) (63.5)<br>**----- End of picture text -----**<br>


## **U-channel & Fan Cover** 

**==> picture [525 x 308] intentionally omitted <==**

**----- Start of picture text -----**<br>
5.71<br>(145.0) 0.89 3.94<br>(22.5) (100.0)<br>0.24 5.23<br>(6.1) (132.7) 0.47<br>(12.0)<br>Pin 16<br>8-32 UNC Mounting hole<br>(in 4 positions)<br>2.95<br>(99.0)3.90 (82.9)3.26 P2 Ø 0.14 (3.5) (75.0)<br>Mounting hole<br>1 M3 Mounting hole<br>P1 3 (4 positions) (in 4 positions)<br>Pin 1<br>=<br>Earth/Safety Ground Tag<br>1.18 3.35 0.55 4.60<br>(30.0) (85.0) (14.1) (116.8)<br>M3 Mounting hole<br>(in 2 positions each side)<br>a|<br>2.14<br>(54.4) 1.57 Notes<br>(40.0) 0.74 1. Suitable for class I operation only.<br>(18.7)<br>\ 2. All dimensions are in inches (mm)<br>3. Weight: 1.98 lbs (900 g) approx.<br>4. Tolerance ±0.02 (0.5)<br>ey7 (40.8)1.60 (63.5)2.50 8-32 UNC Mounting hole(in 2 positions each side) 5. Mounting screws must not penetrate by more than<br>0.12” (3.0 mm) max<br>**----- End of picture text -----**<br>


09 May 2023