R45C-MII-IIQ

R45C Modbus® to Dual Analog Input-Output Converter Quick Start Guide 

## Features 

This guide is designed to help you set up and install the R45C ModBus to Dual Analog Input-Output Converter. For complete information on programming, per­ formance, troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at www.bannerengineering.com. Search for part num­ ber 232576 to view the Instruction Manual. Use of this document assumes familiarity with pertinent industry standards and practices. 

## Overview 

Analog In Analog Out PDO Outside Valid Range (POVR) When an analog input value is received by this converter, This converter also allows for the user to output an analog val­ If the Process Data Out (PDO) value sent to this converter is outside the numerical representational value is sent to the appropri­ ue by sending the numerical analog value by entering the ana­ of the PDO Analog Range value, then the actual analog output value ate ModBus register. log value into the appropriate ModBus register. will be set to the one of the three selectable POVR levels after a 2 second delay: Analog Input Ranges: Analog Output Ranges: • Low (default): 0 V or 3.5 mA • Voltage = 0 mV to 11,000 mV • Voltage = 0 mV to 11,000 mV • High: 10.5 V or 20.5 mA • Current = 0 µA to 24,000 µA • Current = 0 µA to 24,000 µA • Hold: Level retains previous value indefinitely 

## Mechanical Installation 

Install the R45C to allow access for functional checks, maintenance, and service or replacement. Do not install the R45C in such a way to allow for intentional defeat. 

Fasteners must be of sufficient strength to guard against breakage. The use of permanent fasteners or locking hardware is recommended to prevent the loosen­ ing or displacement of the device. The mounting hole (4.5 mm) in the R45C accepts M4 (#8) hardware. 

**==> picture [32 x 38] intentionally omitted <==**

CAUTION: Do not overtighten the R45C's mounting screw during installation. Overtightening can affect the performance of the R45C. 

## Status Indicators 

The R45C ModBus to Dual Analog Input-Output Converter has four amber LED indicators on both sides for IO­Link and analog communications to allow for in­ stallation needs and still provide adequate indication visibility. There is also a green LED indicator on both sides of the converter, which signals the device's pow­ er status. 

## ModBus Amber LED 

**==> picture [500 x 239] intentionally omitted <==**

**----- Start of picture text -----**<br>
Indication  Status<br>Off  ModBus communications are not present<br>Flashing Amber (4 Hz)  ModBus communications are active<br>Solid for 2 Seconds to Off  ModBus communications are lost after connection<br>Solid for 2 Seconds to Flashing Amber (4 Hz)  ModBus communications momentarily lost, but communication reestablished<br>Analog In Amber LED<br>Indication  Status<br>Off  Analog current value is less than setpoint SP1 OR analog value is greater than setpoint SP2<br>Solid Amber  Analog current value is between setpoint SP1 AND setpoint SP2<br>Default Current Values: Default Voltage Values:<br>• SP1 = 0.004 A  • SP1 = 0 V<br>• SP2 = 0.02 A  • SP2 = 10 V<br>Analog Out Amber LED<br>Indication  Status<br>Off  Turns off if written PDO analog value is outside the allowable output range<br>Solid Amber  Turns on if written PDO analog value is inside the allowable output range<br>Allowable Current Range: 0 mA to 24 mA<br>Allowable Voltage Range: 0 V to 11 V<br>**----- End of picture text -----**<br>


## Specifications 

Supply Voltage 12 V DC to 30 V DC at 50 mA maximum Power Pass-Through Current 4 A maximum 

Analog Input Impedance Current version: Approximately 250 ohms Voltage version: Approximately 14.3K ohms 

## Analog Output Load Resistance 

Current version: 1 kilo­ohm maximum load resis­ tance at 24 V DC Maximum Load Resistance = [(Vcc - 4.5) ÷ 0.02 ohms] Voltage version: 2.5 kilo­ohms minimum load resis­ tance 

Original Instructions November 14, 2023 

© Banner Engineering Corp. 

p/n: 232575 Rev. B 

R45C Modbus® to Dual Analog Input-Output Converter Quick Start Guide 

Supply Protection Circuitry Protected against reverse polarity and transient voltages 

Leakage Current Immunity 400 µA 

Accuracy 0.5% 

Vibration and Mechanical Shock 

Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 0.5 mm amplitude, 5 minutes sweep, 30 minutes dwell) 

Meets IEC 60068-2-27 requirements (Shock: 15G 11 ms duration, half sine wave) 

Resolution 

## Product Identification 

Required Overcurrent Protection 

WARNING: Electrical connections must be made by qualified personnel in accor­ dance with local and national electrical codes and regula­ tions. 

Certifications Banner Engineering BV Park Lane, Culliganlaan 2F bus 3 1831 Diegem, BELGIUM C € 

14 bits 

Connections 

(1) Integral 5­pin M12 male quick­disconnect con­ nector 

(2) Integral 4-pin M12 female quick-disconnect connector 

Construction Coupling Material: Nickel-plated brass Connector Body: PVC translucent black 

Environmental Rating IP65, IP67, IP68 UL Type 1 

Operating Conditions 

- Temperature: –40 °C to +60 °C (–40 °F to +140 °F) 

90% at +60 °C maximum relative humidity (noncondensing) Storage Temperature: –40 °C to +80 °C (–40 °F to 

Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with exter­ nal fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to www.bannerengineering.com. 

**==> picture [130 x 61] intentionally omitted <==**

**----- Start of picture text -----**<br>
Supply  Required Over­ Supply  Required Over­<br>Wiring  current Protection  Wiring  current Protection<br>(AWG) (A) (AWG) (A)<br>20 5.0 26 1.0<br>22 3.0 28 0.8<br>24 1.0 30 0.5<br>**----- End of picture text -----**<br>


+176 °F) 

## Banner Engineering Corp Limited Warranty 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engi­ neering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMI­ TATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PER­ FORMANCE, COURSE OF DEALING OR TRADE USAGE. 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCI­ DENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. 

For patent information, see www.bannerengineering.com/patents. 

Document title: R45C Modbus® to Dual Analog Input­Output Converter Quick Start Guide Part number: 232575 

Revision: B Original Instructions © Banner Engineering Corp. All rights reserved. 

**==> picture [30 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
232575<br>**----- End of picture text -----**<br>


page 2 

November 14, 2023 

© Banner Engineering Corp. All rights reserved.