PH18CNP50PASA

## **Photoelectrics Retro-reflective, Polarized Type PH18CNP..., DC** 

- **Miniature sensor range** 

- **Range: 5 m** 

- **Sensitivity adjustment by potentiometer** 

- **Modulated, red light 625 nm** 

- **Supply voltage: 10 to 30 VDC** 

- **Output: 100 mA, NPN or PNP, N.O & N.C.** 

- **Degree of protection: IP67, IP69K** 

- **LED indication for output, stability and power ON** 

- **Protection: reverse polarity, short circuit and transients** 

- **Cable, plug and pigtail versions** 

- **Excellent EMC performance** C€ @« EC@LAB 

**Product Descri tion Orderin Ke p g y PH18CNP50PAM1SA** The PH18CNP... is part of a Compact housing and high **Type** ~~—_—_—______~~ family of inexpensive general power LED for excellent ~~——_—_~~ **Housing style square** ~~Ff~~ purpose retro-reflective senperformance-size ratio. **Housing size** sors in industrial standard 18 The potentiometer used for **Housing material** mm cylindrical and square adjustment of the sensitivi- **Housing type neutral** ABS housing. ty makes the sensors highly **Detection principle** The sensors are useful in flexible. The output type is **Sensing distance** applications where high-acNPN or PNP and the output **Output type** curacy detection as well as switching function is NO and **Output configuration** small size is required. NC. **Connection type Sensitive adjustment** 

## **Product Descri tion p** 

## **T e Selection yp** 

|**Housing style**|**Range**|**Connection**|
|---|---|---|
||**Sn**||
|M18 Square type|5.0 m|Cable|
|M18 Square type|5.0 m|Plug|
|M18 Square type|5.0 m|Pigtail M12|



**Ordering no. Ordering no. NPN PNP Make & break switching Make & break switching PH 18 CNP 50 NASA PH 18 CNP 50 PASA PH 18 CNP 50 NAM1SA PH 18 CNP 50 PAM1SA PH 18 CNP 50 NAT1SA PH 18 CNP 50 PAT1SA** 

## **Specifications** according to EN60947-5-2 

|**Rated operating distance**(Sn) Up to 5.0 m,|) Up to 5.0 m,|
|---|---|
||Reference target: ER4<br>reflector ø 80 mm|
|**Blind zone**|50 mm @ Sn max.|
|**Sensitivity control**<br> Electrical adjustment<br>Mecanical adjustment<br>Adjustable distance to target<br>**Temperature drift**<br>**Hysteresis**(H)<br> (differential travel)<br>**Rated operational volt.**(UB)<br>**Ripple**(Urpp)<br>**Output current**<br>Continuous (Ie)<br>Short-time (I)|Adjustable by potentiometer<br>210˚<br>240˚<br>50-500 cm<br>≤ 0.2%/ºC<br>≤ 20%<br>10 to 30 VDC<br>(ripple included)<br>≤ 10%<br>≤ 100 mA<br>≤ 100 mA|
||(max. load capacity100 nF)|
|**No load supply current**(Io)|≤ 25 mA @ 24 VDC|
|**Minimum operational current**(Im)<br>**OFF-state current**(Ir)|0.5 mA<br>≤ 100 µA|



|**Voltage drop **(Ud)|≤ 2.0 VDC @ 100 mA|
|---|---|
|**Protection**|Short-circuit, reverse|
||polarityand transients|
|**Light source**|InGaAIP,LED,625 nm|
|**Light type**|Red,modulated|
|**Sensing angle**|± 2º|
|**Ambient light**|30.000 lux|
||Incandescent lamp|
|**Light spot Diameter**|Ø 150 mm @ 2.5 m|
|**Operating frequency**|500 Hz|
|**Response time**||
|OFF-ON (tON)|≤ 1.0 ms|
|ON-OFF(tOFF)|≤ 1.0 ms|
|**Power ON delay **(tv)|≤ 100 ms|
|**Output function**||
|Type|NPN or PNP|
|Switchingfunction|NO and NC|
|**Indication**||
|Output ON|LED, yellow|
|Signal stability and power ON|LED, green|



Specifications are subject to change without notice (12.06.2017) 

**1** 

**PH18CNP...** 

## **Specifications (cont.)** 

|**Environment**|||||
|---|---|---|---|---|
|Installation category|III (IEC 60664/60664A;||||
||60947-1)||||
|Pollution degree|3 (IEC 60664/60664A;||||
||60947-1)||||
|Degree ofprotection|IP 67,IP 69K*||||
|**Ambient temperature**|||||
|Operating|-25°to +60°C (-13°to +140°F)||||
|Storage<br>**Vibration**<br>**Shock**<br>**Rated insulation voltage**|-40°to +70°C(-40°to +158°F)<br>10 to 150  Hz, 1.0 mm/15 g<br>(IEC 60068-2-6)<br>30 g / 11ms, 3 pos, 3 neg<br>per axis<br>(IEC 60068-2-6,60068-2-32)<br>500 VAC (rms)<br>IECprotection class III||||
|**Housing material**|||||
|Body|ABS, grey||||
|Backpart|PC-Transparent||||
|Front material|PMMA, red||||



|Cable gland|POM, Black|
|---|---|
|Trimmer shaft|POM, Dark Grey|
|Locknuts|PP, black|
|Mountingbracket|PPA,black|
|**Connection**||
|Cable|PVC, grey, 2 m|
||4 x 0.25 mm2, Ø = 4.5 mm|
|Plug|M12, 4-pin|
||(CONB14NF-series)|
|Pigtail|PUR, grey, 30 cm|
||4 x 0.25 mm2, Ø = 4.5 mm|
||M12, 4-pin|
||(CONB14NF-series)|
|**Weight**|With cable: 85 g|
||With pigtail: 40 g|
||Withplug: 25g|
|**CE-marking**|Yes|
|**Approvals**|cULus (UL508)|
||supply class 2|



* The IP69K test according to DIN 40050-9 for high-pressure, high-temperature wash-down applications. The sensor must not only be dust tight (IP6X), but also able to withstand high-pressure and steam cleaning. The sensor is exposed to high pressure water from a spray nozzle that is fed with 80°C water at 8’000– 10’000 KPa (80–100bar) and a flow rate of 14–6L/min. The nozzle is held 100 –150 mm from the sensor at angles of 0°, 30°, 60° and 90° for 30s each. The test device sits on a turntable that rotates with a speed of 5 times per minute. The sensor must not suffer any damaging effects from the high pressure water in appearance and function. 

**==> picture [62 x 80] intentionally omitted <==**

**----- Start of picture text -----**<br>
90°<br>60°<br>30°<br>0°<br>**----- End of picture text -----**<br>


## **O eration Dia ram p g** 

tv = Power ON delay 

**==> picture [483 x 84] intentionally omitted <==**

**----- Start of picture text -----**<br>
ON<br>Power supply OFF ee<br>Present<br>Target Not Present<br>es es es<br>Present<br>Object Not Present<br>ON Tv a<br>Break Output (N.C.) OFF ne<br>ON SS Tv<br>Make Output (N.O.)  OFF<br>a es ee ee —E>E—Eeee a Oe<br>**----- End of picture text -----**<br>


## **Wiring Diagrams** 

**==> picture [405 x 95] intentionally omitted <==**

**----- Start of picture text -----**<br>
NPN PNP<br>1 BN V 1 BN V<br>4 BK<br>2 WH<br>2 WH<br>4 BK<br>3 BU 3 BU<br>V GND V GND<br>**----- End of picture text -----**<br>


Specifications are subject to change without notice (12.06.2017) 

**2** 

**PH18CNP...** 

## **Detection Diagram** 

## **Excess Gain** 

**==> picture [481 x 366] intentionally omitted <==**

**----- Start of picture text -----**<br>
Sensor<br>Y<br>X ER4<br>Reflector (feet) (feet)<br>0,0 3,3 6,6 9,8 13,1 16,4 19,7 23,0 0,0 3,3 6,6 9,8 13,1 16,4 19,7 23,0<br>150 5,9 100<br>100 3,9<br>50 2,0<br>0 Pas (ite]|  dT 0,0 10 PN<br>-50 -2,0<br>-100 SS -3,9 ————_——<br>-150 Se -5,9 1 SS<br>0,0 1,0 2,0 3,0 4,0 5,0 6,0 7,0 0,0 1,0 2,0 3,0 4,0 5,0 6,0 7,0<br>Distance (m) Distance (m)<br>gnal Stability Indicationnal Stability Indicationy Indication Indication APH18-MB1<br>Excess Gain<br>1.1 Operation level x 1.1<br>1.0 Operation level<br>0.9 Operation level x 0.9<br>Time 6.5<br>Green LED ON FreS || Qe) Ø 27 |<br>Yellow LED ON<br>(mm) (inch)<br>Excess Gain<br>Ø 27<br>6.5<br>**----- End of picture text -----**<br>


## **Signal Stability Indicationnal Stability Indicationy Indication Indication** 

## **Mountin S stems g y** 

**==> picture [135 x 91] intentionally omitted <==**

**----- Start of picture text -----**<br>
M18 Locknut<br>APH18-MB1<br>Min. 1.0 mmMax. 4.5 mm<br>**----- End of picture text -----**<br>


PH18 mounting with a combination of 1 x APH18-MB1 and 1 x M18 locknut. Maximum torque 0.9 NM 

Specifications are subject to change without notice (12.06.2017) 

**3** 

**PH18CNP...** 

## **Dimensions** 

**==> picture [72 x 72] intentionally omitted <==**

**==> picture [500 x 424] intentionally omitted <==**

**----- Start of picture text -----**<br>
Cable/Pigtail version<br>31.5 Power and Stability  15 Operation  Power and Stability  Pigtail M12<br>10.5 17.5 Indicator (Green) Indicator (Yellow) Indicator (Green)<br>3.4<br>3 Emitter<br>Sensitivity Control 240°<br>Receiver<br>Optical Axis<br>Ø 9.9<br>Ø 4.5<br>Plug version<br>31.5 Power and Stability  15 Operation  Power and Stability<br>10.5 17.5 Indicator (Green) Indicator (Yellow) Indicator (Green)<br>3.4<br>3 Emitter<br>Sensitivity Control 240°<br>Receiver<br>Optical Axis<br>M12 x 1 plug<br>1<br>2 4<br>3<br>1<br>2 4<br>3<br>1.5<br>5.45<br>11<br>3.5<br>24.1 35<br>M18 x 1 3.5<br>6.3<br>1.5<br>5.45<br>11<br>3.5<br>24.1 35<br>M18 x 1 3.5<br>10.8<br>**----- End of picture text -----**<br>


## **Installation Hints** 

**==> picture [500 x 118] intentionally omitted <==**

**----- Start of picture text -----**<br>
To avoid interference from inductive voltage / Relief of the cable strain Protection of the sensing face Sensor mounted on a mobile carrier<br>current peaks, separate the proximity switch<br>cables from any other power cables. E.g.<br>Engine, contactor or solenoid cables<br>Incorrect Incorrect<br>Incorrect<br>Correct Correct<br>> 100 mm<br>A proximity switch should not serve Any repetitive flexing of the<br>The cable should not be pulled as mechanical stop cable should be avoided<br>**----- End of picture text -----**<br>


Specifications are subject to change without notice (12.06.2017) 

**4** 

## **Deliver Contents y** 

- Photoelectric switch: PH 18 CNP... 

- Installation instruction on plastic bag 

**==> picture [72 x 72] intentionally omitted <==**

## **Accessories** 

   - Connector type CONG1A.. / CONB14NF.. series 

   - Reflector type ER.. - to be purchased separately 

- Screwdriver 

- Mounting bracket APH18-MB1 

- 1 M18 lock nuts 

- **Packaging:** Plastic bag 

Specifications are subject to change without notice (12.06.2017) 

**5**