PD98CNT30QMU

## **Photoelectrics Through-beam, Relay Output Type PD98CNT30QMU** 

- **Domestic garage door control** 

- **Range 15 m or 30 m** 

- **Modulated, infrared light** 

- **Supply voltage: 12 to 24 VAC/DC** 

- **SPDT relay output** 

- **LED for output indication** 

- **Protection: reverse polarity, transients** 

- **Connection, terminal block** 

- **Emitter mute and gain adjustment** 

- **CE and UL325 approved** 

## **Product Descri tion p** 

The PD98CNT30QMU senIncreased safety by build-in: sor is developed specifically - Sensor test function; the for the domestic and indusemitter has a built-in test trial door market. The seninput designed to mute the sor meets the new regulaemitter and thus evaluate the tions for industrial doors in sensor function. Test funcEurope . The compact size tion is to be activated by the of the outdoor sensor allows door controller. easy on-wall-mounting withHigh neighbour immunity out building the sensor into can be achieved using the the wall. The sensor is easy synchronization feature. to use and no sensitivity The sensor works with a adjustments are necessary. power-supply from 12 to 24 The spherical lens design is VAC/DC. The housing is superior to previous design made of Polycarbonate for of sensors with built-in maximum lifetime and outparabolic reflectors that had standing impact strength. corrosion and dust problems. 

High neighbour immunity can be achieved using the synchronization feature. The sensor works with a power-supply from 12 to 24 VAC/DC. The housing is made of Polycarbonate for maximum lifetime and outstanding impact strength. 

**Ordering Key PD98CNT30QMU Type** ~~el~~ **Housing style Housing size Housing material Sensor code Detection principle Sensing distance Output type Output configuration Mute function** 

## **T e Selection yp** 

|**Housing**|**Range**|**Ordering no.**|
|---|---|---|
|**size**|**Sn**|**Receiver + Emitter**|
|**98 x 56 x 37 mm**|**30 m**|**PD98CNT30QMU**|



## **S ecifications Emitter p** 

|**Rated operational volt.** (Ue)|12 V to 24 VAC/DC|
|---|---|
|**Ripple** (Urrp)|≤10%|
|**Supply current**|≤20 mA|
|**Protection**|Reversepolarity,transients|
|**Control input**<br>Normal oper.|< 1.5 VAC or < 1 VDC|
|Mute|> 3.5 VAC or > 2 VDC|



|**Light source**|LED,880 nm|
|---|---|
|**Light type**|Infrared,modulated|
|**Optical angle**|± 5°(usingaperture)*|
|**Synchronization**||
|Sync. ON|PCB patch** “SYNC”|
||closed|
|Sync. OFF|PCB patch** “SYNC”|
||open (factory settings)|



- With aperture the distance is reduced by 30 % 

- ** Solder bridge 

**1** 

Specifications are subject to change without notice (12.02.2010) 

**PD98** 

## **S ecifications Receiver p** 

|**Rated operating dist.**(Sn)|30 m with open PCB gain|
|---|---|
||patch**|
|**Blind zone**<br>**Temperature drift**<br>**Hysteresis** (H)|15 m with closed PCB gain<br>patch**(factorysettings)<br>None<br>≤0.4%/°C<br>3 - 20%|
|**Rated operational volt.** (Ue)|12 to 24 VAC/DC|
|**Ripple** (Urrp)|≤10%|
|**Output current**||
|Continuous (Ie)<br>Lifetime contacts|1 A / 30 VDC<br>0,5 A / 30 VAC<br>> 100 000 AC11 or DC11|
|**No load supply current**(Io)|≤30 mA|



** Solder bridge 

|**Ambient light**||>20.000 LUX|
|---|---|---|
|**Optical angle**||± 5°(usingaperture)***|
|**Protection**||Reversepolarity,transients|
|**Operating frequency** (f)||25 Hz|
|**Response time**|OFF-ON (tON)|≤20 ms|
||ON-OFF(tOFF)|≤20 ms|
|**Power ON delay** (tv)||≤300 ms|
|**Indication function**|||
|Output ON||LED, yellow|
|**Synchronization**|||
|Sync. ON||PCB patch** “SYNC”|
|||closed|
|Sync. OFF||PCB patch** “SYNC”|
|||open (factory settings)|



*** With aperture removed the distance and angle will be increased, and the sensor no longer meets ESPE type 2. 

## **General S ecifications p** 

|**Environment**||
|---|---|
|Overvoltage category|II (IEC 60664/60664A,<br>60947-1)|
|Pollution degree<br>Degree ofprotection<br>**Temperature**<br>Operating<br>Storage<br>**Vibration**<br>**Shock**|3 (IEC 60664/60664A,<br>60947-1)<br>IP 54(IEC 60529,60947-1)<br>-20° to +60°C (-4° to +140°F)<br>-25° to +80°C(-13° to +176°F)<br>10 to 150 Hz, 0.5 mm/7.5 g<br>(IEC 60068-2-6)<br>2 x 1 m & 100 x 0.5 m<br>(IEC 60068-2-32)|



|**Rated insulation voltage**|**Rated insulation voltage**|50 VDC|
|---|---|---|
|**Housing material**|||
|Front||PC black|
|Backpart||ABS|
|**Connection**|||
|Emitter||3 pole terminal block|
|Receiver||5pole terminal bock|
|**Weight**|||
|Set||185g|
|**CE-marking**||EN12445, EN12453,|
|||EN12978|
|**UL-Approval**|c�us|UL325, CSA-C22.2 No.247|



## **O eration Descri tion p p** 

- The sensor shall be mounted with the draininghole facing down. 

- The sensor must be mounted with silicone between the sensor and mounting wall to avoid water entering the sensor. 

- The cable must be mounted pointing downwards to avoid water entering the sensor (See Dimensions). 

- This product can only be used to detect direct interruption between Tx and Rx; it must not be reflected 

- The sensors must be mounted on a hard vibration-free surface 

- In order to obtain an “ESPE type 2” safety device, the sensors must be connected to a control system fittet with “Photo test” 

## **O eration Dia ram p g** 

tv = Power ON delay Power supply Target emitter present Object present Break (NC) Output ON Make (NO) Output ON Mute active >3.5 VAC OR > 2 VDC 

**==> picture [341 x 89] intentionally omitted <==**

**2** 

Specifications are subject to change without notice (12.02.2010) 

**PD98** 

## **Dimensions** 

## **Detection Diagram** 

**==> picture [229 x 231] intentionally omitted <==**

**----- Start of picture text -----**<br>
56 mm<br>48.6 mm 37 mm<br>UP UP<br>=<br>Ø 3.3 mm<br>@ ) @ !<br>DOWN DOWN<br>98 mm<br>**----- End of picture text -----**<br>


**==> picture [200 x 144] intentionally omitted <==**

**----- Start of picture text -----**<br>
Detection diagram<br>1.5<br>1<br>0.5<br>0<br>-0.5<br>-1<br>-1.5<br>0 10 20 30 40<br>Sensing range [m]<br>30 m 30 m 15 m 15 m<br>[m]<br>**----- End of picture text -----**<br>


## **Excess Gain** 

**==> picture [231 x 99] intentionally omitted <==**

**----- Start of picture text -----**<br>
100000<br>10000<br>1000 30 m<br>100 15 m<br>10<br>1<br>100 1000 10000 100000<br>Sensing Range (mm)<br>**----- End of picture text -----**<br>


## **Wiring Diagram** 

## **Deliver Contents y** 

- PD98 emitter & receiver 

- Installation instruction 

**==> picture [498 x 248] intentionally omitted <==**

**----- Start of picture text -----**<br>
Emitter Receiver<br>• Packaging:  Cardboard box<br>32 12 to 24 VAC/DC +- 54 12 to 24 VAC/DC +- •••  4 pcs raw plugs 4 pcs screws for raw plugs 4 pcs 3 x 14 mm self cutting screws for top mounting<br>1 Mute input 3<br>2 1A 30VDC<br>Relay<br>0.5A 30VAC<br>1<br>Xb = } =<br>Installation Hints<br>To avoid interference from inductive voltage/ Relief of cable strain Protection of the sensing face Switch mounted on mobile carrier<br>current peaks, separate the prox. switch pow-<br>er cables from any other power cables, e.g.<br>motor, contactor or solenoid cables<br>Incorrect<br>Correct<br>The cable should not be pulled A proximity switch should not serve as Any repetitive flexing of the<br>mechanical stop cable should be avoided<br>pe  ea<br>**----- End of picture text -----**<br>


**3** 

Specifications are subject to change without notice (12.02.2010)