PD30CNR06PPM5DU

**Photoelectrics Retro-reflective Type PD30CNR06....DU** 

- **Miniature sensor range** 

- **Range: 6 m, with reflector** 

- **Sensitivity adjustment by Teach-In programming** 

- **Modulated, infrared light 880 nm** 

- **Supply voltage: 10 to 30 VDC** 

- **Output: 100 mA, NPN or PNP preset** 

- **Make and break switching function programmable** 

- **LED indication for output, stability and power ON** 

- **Protection: reverse polarity, short circuit and transients** 

- **Cable and plug versions** 

- **Excellent EMC performance** 

- **• Dust alarm output** CE We 

## **Product Descri tion p** 

The PD30CNR06 sensor The Teach-In function for family comes in a compact adjustment of the sensitivity 10 x 30 x 20 mm reinforced makes the sensors highly PMMA/ABS housing. flexible. The output type is The sensors are useful in preset (NPN or PNP), and the applications where highoutput switching function is accuracy detection as well as one programmable (NO or small size is required. NC) and one dust output NO Compact housing and high or NC. power LED for excellent performance-size ratio. 

## **Ordering Key PD30CNR06PPM5DU** 

**Type Housing style Housing size Housing material Housing length Detection principle Sensing distance Output type Output configuration Connection type Dust output** 

## **T e Selection yp** 

|**Housing**|**Range**|**Connection**|
|---|---|---|
|**W x H x D**|**Sn**||
|10 x 30 x 20 mm|6 m|Cable|
|10 x 30 x 20 mm|6 m|Plug|



**Ordering no. Ordering no. NPN PNP Make or break switching Make or break switching PD 30 CNR 06 NPDU PD 30 CNR 06 PPDU PD 30 CNR 06 NPM5DU PD 30 CNR 06 PPM5DU** 

**Note:** Reflectors to be ordered seperately 

## **S ecifications p** 

|**Rated operating distance**(Sn)|Up to 6 m, with reflector|
|---|---|
||Ø 80 mm (ER4)|
||4 m on ER4060 reflector|
|**Blind zone**<br>**Sensitivity**<br>**Temperature drift**<br>**Hysteresis**(H)<br>(differential travel)<br>**Rated operational volt.**(UB)<br>**Ripple** (Urpp )<br>**Output current**<br>Continuous (Ie)<br>Short-time (I)<br>**Dust output current**<br>Continuous (Ie)<br>Short-time (I)<br>**No load supply current** (Io)|100 mm<br>Adjustable byTeach-In<br>≤0.1%/ºC<br>≤10%<br>10 to 30 VDC<br>(ripple included)<br>≤10%<br>≤100 mA<br>≤100 mA<br>(max. load capacity100 nF)<br>≤20 mA<br>≤20 mA<br>(max. load capacity100 nF)<br>≤30 mA @ 24 VDC|
|**Minimum operational current** (Im)|0.5 mA|
|**OFF-state current** (Ir )|≤100µA|
|**Voltage drop**(Ud)|≤2.4 VDC @ 100 mA|



|**Protection**|Short-circuit, reverse polarity|
|---|---|
||and transients|
|**Light source**|GaAlAs, LED, 880 nm|
|**Light type**|Infrared, modulated|
|**Sensing angle**|± 2º|
|**Ambient light**|10,000 lux|
|**Light spot**|110 mm @ 1.5 m|
|**Operating frequency**|1000 Hz|
|**Response time**||
|OFF-ON (tON)|≤0.5 ms|
|ON-OFF(tOFF )|≤0.5 ms|
|**Power ON delay** (tv)|≤300 ms|
|**Output function**||
|NPN and PNP|Preset|
|NO/NC switching function|Set up by button|
|Output configuration||
|Programming options||
|Output pin 4 black|NO or NC|
|Output|NO or NC (dust)|
|Dust alarm output||
|Delayon operate|20 ms|
|**Indication**||
|Output ON|LED, yellow|
|Signal stability ON and power ON|LED, green|



**1** 

Specifications are subject to change without notice (09.12.2008) 

**PD30CNR06....DU** 

## **Specifications (cont.)** 

|**Environment**||
|---|---|
|Installation category<br>Pollution degree|III (IEC 60664/60664A;<br>60947-1)<br>3 (IEC 60664/60664A;|
|Degree ofprotection|60947-1)<br>IP 67(IEC 60529;60947-1)|
|**Ambient temperature**||
|Operating<br>Storage<br>**Vibration**<br>**Shock**|-25°to +55°C (-13°to +131°F)<br>-40°to +70°C(-40°to +158°F)<br>10 to 55 Hz, 0.5 mm/7.5 g<br>(IEC 60068-2-6)<br>30 g / 11ms, 3 pos, 3 neg<br>per axis|
||(IEC 60068-2-6, 60068-2-32)|



|**Rated insulation voltage**|500 VAC(rms)|
|---|---|
|**Housing material**||
|Body|ABS|
|Front material|PMMA,red|
|**Connection**||
|Cable|PVC, black, 2 m|
||4 x 0.14 mm2, Ø = 3.3 mm|
|Plug|M8,4-pin(CON,54-series)|
|**Weight**|With cable: 40 g|
||Withplug: 10g|
|**CE-marking**|Yes|
|**Approvals**|cULus (UL508)|



## **O eration Dia ram p g** 

tv = Power ON delay 

ON Power supply OFF Present Object Not Present ON Tv Make Output (N.O.) OFF ON Break Output (N.C.) OFF 

**==> picture [8 x 5] intentionally omitted <==**

**----- Start of picture text -----**<br>
Tv<br>**----- End of picture text -----**<br>


## **Wiring Diagrams** 

**==> picture [151 x 103] intentionally omitted <==**

**----- Start of picture text -----**<br>
NPN<br>1 BN V<br>2 WH*<br>4 BK<br>3 BU<br>GND<br>*Dust Output<br>**----- End of picture text -----**<br>


## **Detection Diagram** 

**==> picture [244 x 149] intentionally omitted <==**

**----- Start of picture text -----**<br>
300<br>200<br>100<br>0<br>-100<br>-200<br>-300<br>0 2 4 6 8 10<br>(m)<br>(mm)<br>**----- End of picture text -----**<br>


**==> picture [151 x 103] intentionally omitted <==**

**----- Start of picture text -----**<br>
PNP<br>1 BN V<br>4 BK<br>2 WH*<br>3 BU<br>GND<br>*Dust Output<br>**----- End of picture text -----**<br>


## **Excess Gain** 

**==> picture [245 x 149] intentionally omitted <==**

**----- Start of picture text -----**<br>
100<br>10<br>1<br>0.1 1 10<br>Distance (m)<br>Exess gain<br>**----- End of picture text -----**<br>


**2** 

Specifications are subject to change without notice (09.12.2008) 

**PD30CNR06....DU** 

## **Si nal Stabilit Indication g y** 

**==> picture [244 x 161] intentionally omitted <==**

**----- Start of picture text -----**<br>
Excess Gain<br>1.25 Operation level x 1.25<br>1.0 Operation level<br>0.75 Operation level x 0.75<br>Time<br>Green LED ON<br>Yellow LED ON<br>Dust ON<br>**----- End of picture text -----**<br>


## **Accessories** 

**==> picture [245 x 161] intentionally omitted <==**

**----- Start of picture text -----**<br>
21.2<br>14<br>9° 1.2 32.4<br>25.4<br>3.2 1.2<br>13.5 16.2<br>5.7 6.0 6.0 5.2<br>4.4 4.4<br>Mounting bracket: APD30-MB1 Mounting bracket: APD30-MB2<br>25.4 9°<br>39<br>3.2 26,3 29.3<br>10<br>7.3 10 8.2 4.4<br>16 3 14<br>**----- End of picture text -----**<br>


## **Dimensions** 

**==> picture [502 x 370] intentionally omitted <==**

**----- Start of picture text -----**<br>
Cable version Plug version<br>Teach Button Teach Button<br>Output LED Power / Stability LED Output LED Power / Stability LED<br>Yellow  Green Yellow  Green<br>10.6 10.6<br>10.8 10.8<br>17 17<br>Receiver Two, 9.5 dia. Receiver Two, 9.5 dia.<br>Lenses Lenses<br>Optical axis Optical axis<br>Two M3 Emitter Two M3 Emitter<br>10.25<br>Installation Hints<br>To avoid interference from inductive voltage / Relief of the cable strain Protection of the sensing face Sensor mounted on a mobile carrier<br>current peaks, separate the proximity switch<br>cables from any other power cables. E.g.<br>Engine, contactor or solenoid cables<br>Incorrect<br>Incorrect<br>Incorrect Correct<br>Correct<br>> 100 mm<br>A proximity switch should not serve Any repetitive flexing of the<br>The cable should not be pulled as mechanical stop cable should be avoided<br>10.6 6 10.6 6<br>20 20<br>1.1 1.1<br>5.5 5.5<br>30 25.4 22 30 25.4 22<br>5.5 5.5<br>15 15<br>**----- End of picture text -----**<br>


## **Deliver Contents y** 

- Photoelectric switch: PD 30 CNR 06 ... 

- Installation instruction 

## **Accessories** 

   - Reflector is to be purchased seperately 

   - Mounting bracket APD30-MB2 to be purchased seperately 

- Mountingbracket APD30-MB1 

- **Packaging:** Cardboard box 

**3** 

Specifications are subject to change without notice (09.12.2008) 

**PD30CNR06....DU** 

## **Teach functions** 

## **Normal operation, optimized switching point.** 

1. Line up the sensor with the reflector. Yellow LED and Green LED are ON. 

2. Press the button for 3 seconds until both LEDs flashes simultaneously. 

   - (The first switch point is stored) 

3. Place the object between the sensor and reflector in the detection zone. 

4. Press the button once and the sensor is ready to operate (Green LED ON, Yellow LED ON) (The second switch point is stored) 

**==> picture [196 x 81] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2 3 4<br>3 sec. Push once<br>**----- End of picture text -----**<br>


## **For maximum sensing distance** 

## **(default setting)** 

1. Line up the sensor with the reflector, place the object between the sensor and reflector in the detection zone. Yellow LED is OFF and Green LED is ON. 

2. Press the button for 3 seconds until both LEDs flashes simultaneously. 

   - (The first switch point is stored) 

3. Press the button a second time and the sensor is ready to operate (Green LED ON, Yellow LED ON) (The second switch point is stored) 

**==> picture [162 x 83] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2 3<br>3 sec. Push once<br>**----- End of picture text -----**<br>


## **For minimum detection overhead.** 

1. Line up the sensor with the reflector. Yellow LED and Green LED are ON. 

2. Press the button for 3 seconds until both LEDs flashes simultaneously. 

## **For dynamic set-up (running process)** 

1. Line up the sensor with the reflector. Green LED is ON, status on the yellow LED is not important. 

2. Press the button for 3 second until both LEDs flashes simultaneously. 

3. Press the button a second time for at least one second, both LED’s flashes fast siultainiously and keep the button pressed for at least one process cycle, release the button and the sensor is ready to operate (The second switch point is stored) 

**==> picture [159 x 83] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2 3<br>3 sec. One cycle<br>**----- End of picture text -----**<br>


## **For make or break set-up (N.O. or N.C.)** 

1. Press the button for 10 seconds, until the green LEDs flashes. 

2. While the green LED flashes, the output is inverted each time the button is pressed. Yellow LED indicates N.O. function selected. 

   - If the button is not pressed within the next 10 seconds, the current output is stored. 

**==> picture [133 x 81] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2<br>10 sec. Push once<br>**----- End of picture text -----**<br>


## **For dust output (N.O. or N.C.)** 

      1. Press the button for 15 seconds, until the yellow LEDs flashes. 

      2. While the yellow LED flashes, the dust output is inverted each time the button is pressed. Green LED indicates N.O. function selected. 

         - If the button is not pressed within the next 10 

         - seconds, the current output is stored. 

   - (The first switch point is stored) 

3. Press the button a second time and the sensor is ready to operate (Green LED ON, Yellow LED ON) (The second switch point is stored) 

**==> picture [162 x 81] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2 3<br>3 sec. Push once<br>**----- End of picture text -----**<br>


**==> picture [133 x 81] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2<br>15 sec. Push once<br>**----- End of picture text -----**<br>


**4** 

Specifications are subject to change without notice (09.12.2008)