PCK0E122MCO1GS

**CONDUCTIVE  POLYMER  ALUMINUM  SOLID  ELECTROLYTIC  CAPACITORS** 

## **PCK** 

Chip Type, Ultra-low ESR 

Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. 

SMD type : Lead free reflow soldering condition at 260°C peak correspondence. 

**PCJ** Low ESR **PCK** |]c7 

Compliant to the RoHS directive (2011/65/EU). 

|Item<br>~~|~~<br>~~ee~~|Performance Characteristics<br>~~|~~|
|---|---|
|Category Temperature Range<br>~~ee~~|–55 to +105°C|
|Rated Voltage Range<br>~~ee~~<br>~~ne~~<br>~~a~~|2.5 to 6.3V<br>~~ne~~<br>|
|Rated Capacitance Range<br>~~ne~~<br>~~a~~|220 to 2200µF<br>~~ne~~<br>|
|Capacitance Tolerance<br>~~a|~~<br>~~es~~|± 20%   at 120Hz,20°C<br>~~|~~|
|Tangent of loss angle(tanδ)<br>~~es~~|Less than or equal to the specified value at 120Hz, 20°C|
|ESR(<br>1)<br>~~es~~<br>~~a~~|Less than or equal to the specified value at 100kHz, 20°C|
|Leakage Current (<br>2)<br>~~a~~<br>~~a~~|Less than or equal to the specified value .    After 2 minutes' application of rated voltage at 20°C<br>|
|Temperature Characteristics<br>(Max.Impedance Ratio)<br>~~aee~~|Z+105°C / Z+20°C<br>1.25       (100kHz)<br>Z–55°C / Z+20°C<br>1.25<br>~~ee~~|
|Endurance|The specifications listed at right shall be met when the<br>capacitors are restored to 20°C after the rated voltage is<br>applied for 2000 hours at 105°C.<br>Capacitance change<br>tanδ<br>Leakage current (<br>2)<br>ESR (<br>1)<br>Within ± 20% of the initial capacitance value(<br>3)<br>150% or less than the initial specified value<br>150% or less than the initial specified value<br>Less than or equal to the initial specified value<br>~~a~~|
|Damp Heat<br>(Steady State)|The specifications listed at right shall be met when the<br>capacitors are restored to 20°C after the rated voltage is<br>applied for 1000 hours at 60°C, 90% RH.<br>Capacitance change<br>tanδ<br>Leakage current (<br>2)<br>ESR (<br>1)<br>Within ± 20% of the initial capacitance value(<br>3)<br>150% or less than the initial specified value<br>150% or less than the initial specified value<br>Less than or equal to the initial specified value<br>~~a~~|
|Resistance to<br>Soldering Heat<br>|<br>~~es~~|After soldering the capacitor under the soldering conditions<br>prescribed here, the capacitor shall meet the specifications listed at<br>right.<br>Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.<br>The duration for over +230°C temperature at capacitor surface shall<br>not exceed 60 seconds.<br>In case peak temperature is 250°C or less, reflow soldering shall be<br>two times maximum.<br>In case peak temperature is 260°C or less, reflow soldering shall be<br>once.<br>Measurement for solder temperature profile shall be made at the<br>capacitor top and the terminal.<br>Capacitance change<br>tanδ<br>Leakage current (<br>2)<br>ESR (<br>1)<br>Within ± 10% of the initial capacitance value(<br>3)<br>130% or less than the initial specified value<br>130% or less than the initial specified value<br>Less than or equal to the initial specified value<br>~~=~~<br>~~TT~~|
|Marking<br>~~es~~|Navy blue print on the case top|



1  ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 

2  Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 

3  Initial value : The value before test of examination of resistance to soldering. 

**==> picture [508 x 200] intentionally omitted <==**

**----- Start of picture text -----**<br>
Dimensions Positive Type numbering system  (Example : 6.3V 220µF)<br>Plastic platform 1 2 3 4 5 6 7 8 9 10 11 12 13 14<br>Capacitance Lot No. 0.3 MAX. C±0.2 P C K 0 J 2 2 1 M C O 1 G S<br>Taping code<br>Configuration<br>TeL =} i o | Coco Capacitance tolerance (±20%)<br>Series chewed Voltage ( j:6.3v) L +0.1-0.4 gee] H Negative L Rated capacitance L  (220µF)<br>|__ | t h Xe<br>Rated voltage (6.3V)<br>Series name<br>Type<br> (mm)<br>Size φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L<br>φD 6.3 8.0 10.0 10.0<br>L 5.9 6.9 7.9 9.9<br>A 7.3 9.0 11.0 11.0<br>B 6.6 8.3 10.3 10.3 Voltage<br>C 6.6 8.3 10.3 10.3<br>V  2.5  4  6.3<br>E 2.1 3.2 4.6 4.6<br>H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Code  e  g  j<br>0.5 MAX.<br>0 1<br>K 2 4 E<br>C 2 j 9 D±0.5φ B±0.2 A±0.2<br>**----- End of picture text -----**<br>


Dimension table in next page. 

CAT.8100E 

36 

**CONDUCTIVE  POLYMER  ALUMINUM  SOLID  ELECTROLYTIC  CAPACITORS** 

## **PCK** 

## Standard Ratings 

|Rated Voltage<br>(V)(code)|Surge Voltage<br>(V)|Rated Capacitance<br>(µF)|Case Size<br>φD×L (mm)|tanδ|Leakage Current<br>(µA)|ESR (mΩ)<br>(at 100kHz 20°C)|Rated Ripple<br>(mArms)|Part Number|
|---|---|---|---|---|---|---|---|---|
|2.5<br>(0E)|2.8|390|6.3 × 6|0.12|293|10|3900|PCK0E391MCO1GS|
|||560|8 × 7|0.12|420|9|4500|PCK0E561MCO1GS|
|||680|8 × 7|0.12|510|9|4500|PCK0E681MCO1GS|
|||1200|10 × 8|0.12|900|9|5000|PCK0E122MCO1GS|
|||2200|10 × 10|0.12|1650|8|6000|PCK0E222MCO1GS|
|4<br>(0G)|4.6|330|6.3 × 6|0.12|396|10|3900|PCK0G331MCO1GS|
|||470|8 × 7|0.12|564|9|4500|PCK0G471MCO1GS|
|||560|8 × 7|0.12|672|9|4500|PCK0G561MCO1GS|
|||1000|10 × 8|0.12|1200|9|5000|PCK0G102MCO1GS|
|||1800|10 × 10|0.12|2160|8|6000|PCK0G182MCO1GS|
|6.3<br>(0J)|7.2|220|6.3 × 6|0.12|416|10|3900|PCK0J221MCO1GS|
|||330|8 × 7|0.12|624|9|4500|PCK0J331MCO1GS|
|||390|8 × 7|0.12|737|9|4500|PCK0J391MCO1GS|
|||820|10 × 8|0.12|1550|9|5000|PCK0J821MCO1GS|
|||1500|10 × 10|0.12|2835|8|6000|PCK0J152MCO1GS|



Rated ripple current  (mArms) at 105°C 100kHz 

Taping specifications are given in page 23. 

Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 

CAT.8100E 

37