NO5-Q08-AP7-78758

## **Q08 Series Diffuse-Mode Sensors** 

## **Datasheet** 

Low-profile infrared sensors in rugged metal housings 

- Miniature right-angle dc photoelectric sensors in rugged die-cast metal housings 

- Ultra-thin; only 8 mm (0.3 in) deep 

- Totally self-contained; 10 to 30 V dc operation 

- Easy mechanical alignment 

- Circuitry is completely sealed and epoxy-encapsulated; rated IP67 and NEMA 6 

- Select models with NPN (sinking) or PNP (sourcing) output 

- Select light operate or dark operate models 

- 3-wire hookup; output load capacity to 150 milliamps 

- LED indicators for Power ON and Output ON; Output indicator may be used for alignment 

- Infrared, 880 nm 

- Range of 2.5 mm to 61 mm (0.1 in to 2.4 in) 

**==> picture [27 x 5] intentionally omitted <==**

**----- Start of picture text -----**<br>
DIFFUSE<br>**----- End of picture text -----**<br>


|**Models**|**Cable**<br>1|**Output**<br>**Type**|**Performance Curves**<br>2|**Performance Curves**<br>2|
|---|---|---|---|---|
||||**Excess Gain**|**Beam Pattern**|
|NO5-Q08-AN7<br>NO5-Q08-AN7V1131|2 m (6.5 ft)<br>3-Pin Pico QD|NPN/LO|1<br>10<br>100<br>10 mm<br>0.4 in<br>100 mm<br>4.0 in<br>1000 mm<br>40 in<br>1 mm<br>0.04 in<br>1000<br>E<br>X<br>C<br>E<br>S<br>S<br>G<br>A<br>I<br>N<br>DISTANCE<br>~~Q08~~<br>~~Diffuse Mode~~<br>~~a~~<br>~~Se eee~~<br>~~740~~<br>~~_— SSS~~<br>~~Sass~~<br>~~sel~~<br>~~Fae~~<br>~~atm Saale~~<br>~~CT~~<br>PENT TTT|52.5 mm<br>2.5 in<br>40.0 mm<br>2.0 in<br>37.5 mm<br>1.5 in<br>25.0 mm<br>1.0 in<br>12.5 mm<br>0.5 in<br>0<br>0<br>2.5 mm<br>5.0 mm<br>7.5 mm<br>2.5 mm<br>5.0 mm<br>7.5 mm<br>0<br>.1 in<br>.2 in<br>.3 in<br>.1 in<br>.2 in<br>.3 in<br>~~Q08~~<br>~~Diffuse Mode~~<br>DISTANCE<br>~~‘~~<br>~~a~~<br>~~[Zo~~<br>~~Ke~~<br>~~[SNE~~<br>~~a~~<br>~~el a~~<br>~~ee~~<br>~~————~~|
|NO5-Q08-RN7<br>NO5-Q08-RN7V1131|2 m (6.5 ft)<br>3-Pin Pico QD|NPN/DO|||
|NO5-Q08-AP7<br>NO5-Q08-AP7V1131|2 m (6.5 ft)<br>3-Pin Pico QD|PNP/LO|||
|NO5-Q08-RP7<br>NO5-Q08-RP7V1131|2 m (6.5 ft)<br>3-Pin Pico QD|PNP/DO|||



## **WARNING: Not To Be Used for Personnel Protection** 

**Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death.** This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. 

> 1 To order the 9 m (30 ft) cable model, add suffix "W/30" to the cabled model number. For example, NO5-Q08-AN7 W/30. Models with a QD connector require a mating cable. 2 Performance based on 90% reflective white test card. 

Original Document 03558 Rev. E 

10 July 2014 

03558 

Q08 Series Diffuse-Mode Sensors 

## **Overview** 

This small, rugged infrared diffuse proximity mode sensor is contained within an 8-mm deep die-cast metal housing. It is totally self-contained and is powered by 10 to 30V dc. It is ideal for sensing of any reflective surface at up to 2 inches from the sensor face. Typical applications include parts detection on small conveyors and in robot grippers, and other similar short-range sensing applications. 

**==> picture [131 x 15] intentionally omitted <==**

**----- Start of picture text -----**<br>
2<br>1<br>**----- End of picture text -----**<br>


Q08 diffuse sensors have a solid-state output capable of switching loads of up to 150 mA dc, continuous. Four output types are available: NPN sinking/light operate, NPN sinking/dark operate, PNP sourcing/light operate, and PNP sourcing/dark operate. 

A light-operate output conducts when the sensor sees the reflection of its own modulated light (an object is present). A dark-operate output conducts when the sensor does not see the reflection of its own modulated light (no object is present). A green LED indicator, visible from the front and left side of the sensor, lights whenever dc power is applied to the sensor. An amber LED, visible from the front and right side of the sensor, lights whenever the sensor output is conducting. 

## **Specifications** 

## **Supply Voltage and Current** 

10 to 30 V dc at 25 mA; 10% maximum ripple 

## **Supply Protection Circuitry** 

Protected against reverse polarity 

## **Indicators** 

Two LED indicators: 

Green: Lights to indicate dc power ON 

Amber: Lights when sensor output is conducting (in “light” condition for light operate models; in “dark” condition for dark operate models) 

## **Construction** 

Black epoxy-painted die-cast zinc housing, polysulfone thermoplastic lens with two through-mounting holes to accommodate M3 (#4) hardware 

## **Environmental Rating** 

Meets NEMA standards 1, 2, 4, 6, 12 and 13; IEC IP67 

## **Connections** 

PVC-jacketed 2 m (6.5 ft) or 9 m (30 ft) cable or 3-pin Pico-style quickdisconnect (QD) fitting available. Cable is 4.0 mm (0.16 inches) diameter. 

## **Operating Conditions** 

Temperature: 0 °C to +50 °C (+32 °F to +122 °F) Maximum relative humidity: 90% at 50 °C (non-condensing) 

## **Output Configuration** 

Solid-state dc output, with four output types available: NPN sinking/light operate PNP sourcing/light operate NPN sinking/dark operate 

PNP sourcing/dark operate 

Light operate outputs conduct when the receiver sees the reflection of its own modulated light source; Dark operate outputs conduct when the sensor sees dark. 

## **Output Rating** 

150 mA maximum, continuous 

Off-state leakage current is 100 microamps at 30 V dc 

On-state saturation voltage is < 200 millivolts at 10 mA dc and < 1 volt at 150 mA dc 

## **Output Response Time** 

1 millisecond ON and OFF independent of signal strength 

## **Repeatability** 

200 microseconds (0.2 milliseconds), independent of signal strength 

## **Application Notes** 

The horizontal axis of the beam pattern represents a line extending outward from the optical center of the Q08 sensor, and perpendicular to the sensor’s lens. For purposes of mounting and alignment, note that the optical center of the Q08’s lens is not the same as its mechanical center. 

## **Certifications** 

www.bannerengineering.com - Tel: +1-763-544-3164 

P/N 03558 Rev. E 

2 

Q08 Series Diffuse-Mode Sensors 

## **Dimensions** 

**==> picture [515 x 185] intentionally omitted <==**

**----- Start of picture text -----**<br>
Cabled Models Quick-Disconnect Models Optical Center of Beam<br>8.0 mm (0.32")<br>20.0 mm (0.79")<br>32.0 mm 9.7 mm<br>(1.26") 39.1 mm (0.38")<br>(1.54")<br>7.7 mm Optical<br>Center of<br>(0.30")<br>Beam<br>3.00 mm (0.118")<br>ø 3.40 mm (0.134")<br>(2 Holes)<br>2 m (6.5') Cable<br>#4 (M3) Screw Clearance<br>3-pin Pico-Style<br>13.00 mm  (0.512") Quick-Disconnect<br>**----- End of picture text -----**<br>


## **Wiring Diagrams** 

## **NPN (Sinking Models)** 

**==> picture [500 x 105] intentionally omitted <==**

**----- Start of picture text -----**<br>
Cabled Quick Disconnect (3-pin Pico-style)<br>bu – bu –<br>10-30V dc 10-30V dc<br>bn bn<br>+ +<br>bk bk<br>Load Load<br>**----- End of picture text -----**<br>


## **PNP (Sourcing Models)** 

**==> picture [500 x 104] intentionally omitted <==**

**----- Start of picture text -----**<br>
Cabled Quick Disconnect (3-pin Pico-style)<br>bn bn<br>+ +<br>10-30V dc 10-30V dc<br>bu – bu –<br>bk bk<br>Load Load<br>**----- End of picture text -----**<br>


P/N 03558 Rev. E 

www.bannerengineering.com - Tel: +1-763-544-3164 

3 

Q08 Series Diffuse-Mode Sensors 

## **Accessories** 

|**3-Pin Snap/Pico-Style Cordsets**|**3-Pin Snap/Pico-Style Cordsets**|**3-Pin Snap/Pico-Style Cordsets**|**3-Pin Snap/Pico-Style Cordsets**|**3-Pin Snap/Pico-Style Cordsets**|
|---|---|---|---|---|
|**Model**|**Length**|**Style**|**Dimensions**|**Pinout**|
|**PKG3Z-2**|2 m (6.56 ft)|Straight|28 mm max.<br>(1.1")<br>ø 10 mm max.<br>(0.4")|**4**<br>**3**<br>**1**<br>1 = Brown<br>3 = Blue<br>4 = Black|
|**PKW3-2**|2 m (6.56 ft)|Right-Angle|20 mm<br>(0.8")<br>25 mm max.<br>(1.0")<br>ø 12 mm max.<br>(0.5")||



## **Banner Engineering Corp Limited Warranty** 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

## **THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.** 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. **IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.** 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. 

www.bannerengineering.com - Tel: +1-763-544-3164