KTM-WP11181P

KTM-WP11181P KTM Prime 

**CONTRAST SENSORS** 

**KTM-WP11181P | KTM Prime** CONTRAST SENSORS 

Ordering information **Type Part no.** KTM-WP11181P 1062199 Other models and accessories www.sick.com/KTM_Prime 3 ~~li-ion~~ 

## CE® 

## Detailed technical data 

## Features 

|**Dimensions (W x H x D)**|12 mm x 31.5 mm x 21 mm|
|---|---|
|**Sensing distance**|12.5 mm|
|**Housing design (light emission)**|Rectangular|
|**Sensing distance tolerance**|± 3 mm|
|**Light source**|LED, RGB1)|
|**Wave length**|470 nm, 525 nm, 625 nm|
|**Light spot size**|1.5 mm x 6.5 mm|
|**Light spot direction**|Vertical2)|
|**Max. web speed tech-in (dynamic)**|1 m/s3)|
|**Adjustment**|Teach-in button|
|**Teach-in mode**|2-point teach-in static/dynamic + proximity to mark|
|**Output function**|Light/dark switching|



- 1) Average service life: 100,000 h at TU = +25 °C. 

- 2) In relation to long side of housing. 

- 3) At a mark size of 4 mm. 

## Mechanics/electronics 

|**Supply voltage**|12 V DC ... 24 V DC1)|
|---|---|
|**Ripple**|≤ 5 Vpp 2)|
|**Power consumption**|< 50 mA3)|
|**Switching frequency**|15 kHz4)|



- 1) Limit values: DC 12 V (–10 %) ... DC 24 V (+20 %). Operation in short-circuit protected network max. 8 A. 

- 2) May not exceed or fall below Uv tolerances. 

- 3) Without load. 

- 4) With light/dark ratio 1:1. 

- 5) Signal transit time with resistive load. 

- 6) At supply voltage > 24 V, Imax = 30 mA. Imax is consumption count of all Qn. 

**Online data sheet | 2017-07-05 10:40:09 Subject to change without notice** 

**2 REGISTRATION SENSORS | SICK** 

**KTM-WP11181P | KTM Prime** CONTRAST SENSORS 

|**Response time**|35 µs5)|
|---|---|
|**Jitter**|15 µs|
|**Output type**|PNP|
|**Switching output (voltage)**|PNP: HIGH = VS– ≤ 2 V / LOW approx. 0 V|
|**Switching output**|Light/dark switching|
|**Output current Imax.**|50 mA6)|
|**Input, dynamic teach-in (ET)**|PNP: Teach: U = 10,8 V ... < UV<br>Run: U < 2 V or open|
|**Retention time (ET)**|28 ms, non-volatile memory|
|**Connection type**|Connector M8, 4-pin|
|**Protection class**|III|
|**Circuit protection**|UVconnections, reverse polarity protected<br>Output Q short-circuit protected<br>Interference pulse suppression|
|**Enclosure rating**|IP67|
|**Weight**|20 g|
|**Housing material**|ABS|



- 1) Limit values: DC 12 V (–10 %) ... DC 24 V (+20 %). Operation in short-circuit protected network max. 8 A. 

- 2) May not exceed or fall below Uv tolerances. 

- 3) Without load. 

- 4) With light/dark ratio 1:1. 

- 5) Signal transit time with resistive load. 

- 6) At supply voltage > 24 V, Imax = 30 mA. Imax is consumption count of all Qn. 

## Ambient data 

|**Ambient operating temperature**|–10 °C ... +55 °C|
|---|---|
|**Ambient storage temperature**|–20 °C ... +75 °C|
|**Shock load**|According to IEC 60068|
|**UL File No.**|NRKH.E348498 & NRKH7.E348498|



## Classifications 

|**ECl@ss 5.0**|27270906|
|---|---|
|**ECl@ss 5.1.4**|27270906|
|**ECl@ss 6.0**|27270906|
|**ECl@ss 6.2**|27270906|
|**ECl@ss 7.0**|27270906|
|**ECl@ss 8.0**|27270906|
|**ECl@ss 8.1**|27270906|
|**ECl@ss 9.0**|27270906|
|**ETIM 5.0**|EC001820|
|**ETIM 6.0**|EC001820|
|**UNSPSC 16.0901**|39121528|



**2017-07-05 10:40:09 | Online data sheet Subject to change without notice** 

**REGISTRATION SENSORS | SICK** 

**3** 

**KTM-WP11181P | KTM Prime** CONTRAST SENSORS 

Dimensional drawing (Dimensions in mm (inch)) 

KTM Prime 

**==> picture [236 x 254] intentionally omitted <==**

**----- Start of picture text -----**<br>
21<br>(0.83)<br>9.9<br>0.5<br>12 (0.39)<br>(0.02)<br>fe<br>al | D<br>18.3<br>(0.72)<br>3<br>9.7 (0.12)<br>(0.38)<br>Wg. yo<br>-<br>|_ _ |<br>①   Optical axis receiver<br>②   Optical axis sender<br>) (0.04)<br>0.5 0.02(  0.9<br>9 )<br>(0.35) (1.00) 1.12( (1.24)<br>25.4  28.5  31.5<br>9.7 0.38)( 11.4 (0.45)<br>(12.01)<br> 305<br>**----- End of picture text -----**<br>


- ③ M3 mounting hole 

- ④ Cable with male connector M12 (only KTM-xxxxx2x) 

Adjustments 

KTM Prime 

- ① Status indicator LED, yellow: Status switching output Q (dark switching) 

- ② LED indicator green: Supply voltage active 

- ③ Teach-in button 

## Connection diagram 

Cd-092 

**==> picture [48 x 58] intentionally omitted <==**

**----- Start of picture text -----**<br>
brn 1<br>+ (L+)<br>wht 2<br>Teach<br>blu 3<br>-  (M)<br>blk 4<br>Q<br>**----- End of picture text -----**<br>


**Online data sheet | 2017-07-05 10:40:09 Subject to change without notice** 

**4 REGISTRATION SENSORS | SICK** 

**KTM-WP11181P | KTM Prime** CONTRAST SENSORS 

## Concept of operation 

Teach-in dynamic 

## **1. Position background** 

## **2. Move at least the mark** 

## **and background using the light spot.** 

Press the teach-in button and keep it pressed. LED flashing slowly. 

Keep the teach-in button > 3 < 30 s pressed. 

Release the teach-in button. 

Yellow LED will illuminate, when emitted light is on the mark. 

## **Example** 

**==> picture [339 x 92] intentionally omitted <==**

**----- Start of picture text -----**<br>
Dark switching Light switching<br>Internal signal<br>received<br>Switching  Switching<br>threshold threshold<br>Internal signal<br>received<br>Output Q Hi Output Q<br>**----- End of picture text -----**<br>


## **Switching characteristics** 

The optimum emitted light is selected automatically (at RGB variants). Static teach-in: light/dark setting is defined using teach-in sequence. Dynamic teach-in: switching output active on mark, if background is longer in the field of view during the teach-in. The switching threshold is set in the center between the background and the mark. 

If the button is pressed again within 10 s of the teach (> 20 ms < 10 s), the relative switching threshold is placed 75 % between mark (100 %) and background (0 %) (dotted line in Figure). Teach-in can also be performed using an external control signal. 

Keylock activation and deactivation: hold down teach-in button > 30 s. 

Teach-in failure: yellow LED indicator and the transmitted light of the sensor flashing quickly. For dynamic teach-in with ET signal (5 Hz) via switching output Q. 

**2017-07-05 10:40:09 | Online data sheet Subject to change without notice** 

**REGISTRATION SENSORS | SICK** 

**5** 

**KTM-WP11181P | KTM Prime** CONTRAST SENSORS 

## Teach-in static 

## **1. Position mark** 

## **2. Position background** 

Press and hold teach-in Press and hold teach-in button > 1 < 3 s. button < 3 s. Yellow LED flashes slowly. Yellow LED goes out. 

## Characteristic curve 

Sensing distance 

**==> picture [222 x 216] intentionally omitted <==**

**----- Start of picture text -----**<br>
110<br>100<br>| tt pe<br>90<br>| | If, EN<br>80706050403020 P|P|P|P|P|P|Pt Pt ||||||| | |||||| | Vi[||||f[| [| |ff|ffffftjf | fnftftft[|[|ffftfetf ]<br>0 5 10 15 20<br>(0.20) (0.39) (0.59) (0.79)<br>Sensing distance in mm (inch)<br>Relative sensitivity in %<br>**----- End of picture text -----**<br>


## Recommended accessories 

Other models and accessories www.sick.com/KTM_Prime 

||**Brief description**|**Type**|**Part no.**|
|---|---|---|---|
|Device protection (mechanical)||||
||Stainless steel 1.4301 (SVS 304), 3 mm thick protective sleeve for G6, stainless steel<br>1.4301, mounting hardware included|BEF-SG-G6|2069044|



**Online data sheet | 2017-07-05 10:40:09 Subject to change without notice** 

**6** 

**REGISTRATION SENSORS | SICK** 

**KTM-WP11181P | KTM Prime** CONTRAST SENSORS 

|||**Brief description**|**Type**|**Part no.**|
|---|---|---|---|---|
||Mounting brackets and plates||||
|||Mounting bracket for wall mounting, Stainless steel, mounting hardware included|BEF-W100-A|5311520|
|||Mounting bracket for floor mounting, steel, zinc coated, mounting hardware included|BEF-W100-B|5311521|
|||Adapter plate KT3 to KTM, Stainless steel, fastening screws included|BEF-AP-KTMS01|2068786|
||Plug connectors and cables||||
|Head A: female connector, M8, 4-pin, straight<br>Head B: cable<br>Cable: PVC, unshielded, 5 m<br>~~Nw~~|||DOL-0804-G05M|6009872|
|||Head A: female connector, M8, 4-pin, straight|DSL-8204-G0M6|6022571|
|||Head B: male connector, M12, 4-pin, straight|||
||\|Cable: PVC, unshielded, 0.6 m|||



**2017-07-05 10:40:09 | Online data sheet Subject to change without notice** 

**REGISTRATION SENSORS | SICK** 

**7** 

## SICK At A GlAnCe 

SICK is one of the leading manufacturers of intelligent sensors and sensor solutions for industrial applications. A unique range of products and services creates the perfect basis for controlling processes securely and efficiently, protecting individuals from accidents and preventing damage to the environment. 

We have extensive experience in a wide range of industries and understand their processes and requirements. With intelligent sensors, we can deliver exactly what our customers need. In application centers in Europe, Asia and North America, system solutions are tested and optimized in accordance with customer specifications. All this makes us a reliable supplier and development partner. 

Comprehensive services complete our offering: SICK lifetime Services provide support throughout the machine life cycle and ensure safety and productivity. 

For us, that is “Sensor Intelligence.” 

## WOrldWIde preSenCe: 

Contacts and other locations www.sick.com 

SICK AG | Waldkirch | Germany | www.sick.com