K50PFF100AMGRY3Q

K50 Pro with Optical Sensor 

## Features 

50 mm Programmable Multicolor RGB Device with Optical Sensor 

- Programmable using Banner's Pro Editor software and Pro Converter Cable 

- • Up to 14 default colors with flash input in one unit • Devices are completely self-contained—no controller needed • Rated IP67 and IP69K per ISO 20653 • Immune to ambient light, EMI, and RFI interference • 12 V DC to 30 V DC operation 

WARNING: 

- Do not use this device for personnel protection 

- • Using this device for personnel protection could result in serious injury or death. • This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition. 

## Models 

**==> picture [488 x 108] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||||||||
|---|---|---|---|---|---|---|---|
|Family|Style|Activation method|Output State|Output Function|Color Control|Connector|[(1)]|
|K50|P|FF50|A|M|GRY3|Q|
|Blank = 2 m (6.5 ft) integral PVC-|
|FF50 = 50 mm Fixed|jacketed cable|
|Field|[(2)]|
|GRY3 = Progammable|Q = Integral 5-pin or 8-pin M12|
|FF100 = 100 mm Fixed|M = Momentary|Multicolor (3 colors, 5-pin)|male quick-disconnect connector,|
|K50|P = Pro|Field|[(2)]|A = Normally Open|depending on model|
|L = Latching|RGB14 = Programmable|
|FF200 = 200 mm Fixed|Multicolor (14 colors, 8-pin)|QP = 150 mm (6 in) PVC-jacketed|
|cable with a 5-pin or 8-pin M12|
|Field|[(2)]|
|male quick-disconnect connector,|
|depending on model|

**----- End of picture text -----**<br>


## Pro Editor 

Use Banner's Pro Editor software and Pro Converter Cable to create custom configurations by selecting different colors, flash patterns, and animations. For more information visit www.bannerengineering.com/proeditor. 

> (1) Models with a quick-disconnect connector require a mating cordset. 

> (2) Cutoff distance varies from specified range based on target and tolerances. 

Original Instructions 17-Jun-25 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

p/n: 221058 Rev. A 

K50 Pro with Optical Sensor 

## Wiring Diagrams 

**==> picture [46 x 6] intentionally omitted <==**

**----- Start of picture text -----**<br>
GRY3 Models<br>**----- End of picture text -----**<br>


**==> picture [500 x 132] intentionally omitted <==**

**----- Start of picture text -----**<br>
NPN PNP Key<br>bn (1) – bn (1) +<br>12-30 V DC 12-30 V DC<br>bu (3) + bu (3) – Pin 1 = BrownPin 2 = White*<br>Pin 3 = Blue<br>bk (4) bk (4) Pin 4 = Black<br>Load Load Pin 5 = Gray<br>Activation toggles output<br> 1* wh (2)  1* wh (2)<br>*Can be configured as an output<br> 2 gy (5)  2 gy (5) using Pro Editor software<br>**----- End of picture text -----**<br>


GRY3 Multicolor Color/Function Definition 

**==> picture [500 x 44] intentionally omitted <==**

**----- Start of picture text -----**<br>
Green Yellow Red<br>Input 1 X X<br>Input 2 X X<br>**----- End of picture text -----**<br>


RGB14 Models 

**==> picture [500 x 289] intentionally omitted <==**

**----- Start of picture text -----**<br>
NPN PNP Key<br>bn (2) – bn (2) +<br>12-30 V DC 12-30 V DC<br>bu (7) + bu (7) –<br>Pin 1 = White<br>wh (1) Load wh (1) Load Pin 2 = Brown<br>Pin 3 = Green<br> 1 gn (3)  1 gn (3) Pin 4 = YellowPin 5 = Gray*<br>Pin 6 = Pink<br>rd (8) rd (8) Pin 7 = Blue<br> 2  2 Pin 8 = Red<br>ye (4) ye (4) Activation toggles output<br> 3  3<br>*Can be configured as an output<br>gy (5) gy (5) using Pro Editor software<br> 4*  4*<br>pk (6) pk (6)<br>Flash Input Flash Input<br>RGB Multicolor Color/Function Definition<br>Red Yellow Green Cyan Blue Magenta White Amber Rose GreenLime  Orange Sky Blue Violet Spring Green<br>Input 1 X X X X X X X<br>Input 2 X X X X X X X<br>Input 3 X X X X X X X<br>Input 4 X X X X X X X<br>**----- End of picture text -----**<br>


## Specifications 

## Supply Voltage 

12 V DC to 30 V DC 

Supply Current 

150 mA maximum current at 12 V DC (exclusive of load) 

Supply Protection Circuitry 

Protected against reverse polarity and transient voltages Leakage Current Immunity 400 µA 

## Output Rating 

Maximum load: 150 mA 

ON-state saturation voltage: < 2 V DC at 10 mA; <2.5 V DC at 150 mA 

OFF-state leakage current: <10 µA at 30 V DC 

Output Response Time 

Power-Up Delay: 500 milliseconds maximum Input Response: 40 milliseconds maximum Output Response: 300 milliseconds maximum 

page 2 of 8 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

17-Jun-25 

K50 Pro with Optical Sensor 

## Operating Conditions 

–40 °C to +50 °C (–40 °F to +122 °F) 

Humidity: 90% at +50 °C maximum relative humidity (noncondensing) 

## Environmental Rating 

Standard Models: IP67, IP69K per ISO 20653 

Cabled models also meet IP69K per ISO 20653 if the cable and cable entrance are protected from high-pressure spray 

## Mounting 

## Connections 

2 m (6.5 ft) integral PVC-jacketed cable, integral 5-pin or 8-pin M12 male quick-disconnect connector, or 150 mm (6 in) PVCjacketed cable with a 5-pin or 8-pin M12 male quickdisconnect connector, depending on model 

Models with a quick disconnect require a mating cordset 

## Storage 

–40 °C to +70 °C (–40 °F to +158 °F) 

Required Overcurrent Protection 

M30 × 1.5 threaded base, maximum torque 4.5 N·m (40 in·lbf) 

Pro Editor Configuration 

Connection to Pro Editor software enables control of: 

- Animation: Steady, Flash, Two Color Flash, 50/50, 50/50 Rotate, Chase, Intensity Sweep, Demo 

- Color: Green, Red, Yellow, Blue, White, Cyan, Magenta, Amber, Rose, Lime Green, Orange, Sky Blue, Violet, Spring Green 

- Intensity: Low, Medium, High 

- Speed: Slow, Standard, Fast 

- Output State: Normally Open, Normally Closed, Momentary, Latching, On Delay, Off Delay 

- Logic Type: Three State Advanced Control (F2 Mode), Seven State Advanced Control (F2 Mode), Four State Full Logic (Custom) 

- One pin configurable as either an input or an output 

Pro Converter Cable required to interface between PC and indicator, see accessories 

## Construction 

Standard Model Base, Dome, and Nut: Polycarbonate 

## Vibration and Mechanical Shock 

Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 1.0 mm amplitude, 5 minutes sweep, 30 minutes dwell) Meets IEC 60068-2-27 requirements (Shock: 30G 11 ms duration, half sine wave) 

WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. 

Overcurrent protection is required to be provided by end product application per the supplied table. 

Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. 

Supply wiring leads < 24 AWG shall not be spliced. 

For additional product support, go 

to www.bannerengineering.com. 

|Supply<br>Wiring<br>(AWG)<br>20|Required Overcurrent<br>Protection (A)<br>5.0|Required Overcurrent<br>Protection (A)<br>5.0|Supply<br>Wiring<br>(AWG)<br>26|Required Overcurrent<br>Protection (A)<br>1.0|Required Overcurrent<br>Protection (A)<br>1.0|
|---|---|---|---|---|---|
|22|3.0||28|0.8||
|24|1.0||30|0.5||



Certifications 

Banner Engineering BV Park Lane, Culliganlaan 2F bus 3 1831 Diegem, BELGIUM 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

page 3 of 8 

17-Jun-25 

K50 Pro with Optical Sensor 

## Default Indicator Characteristics 

**==> picture [483 x 244] intentionally omitted <==**

**----- Start of picture text -----**<br>
Color Coordinates [(3)]<br>Color Dominant Wavelength (nm)or Color Temperature  Lumen Output (Typical at 25 °C)<br>(CCT) x y<br>Green 522 0.154 0.700 14.2<br>Red 620 0.689 0.309 7.1<br>Yellow 576 0.477 0.493 20.5<br>Blue 466 0.140 0.054 4.0<br>White 5700K 0.328 0.337 21.6<br>Cyan 493 0.170 0.340 15.8<br>Magenta – 0.379 0.172 9.5<br>Amber 589 0.556 0.420 13.5<br>Rose – 0.515 0.220 7.8<br>Lime Green 562 0.388 0.561 18.4<br>Sky Blue 486 0.155 0.247 16.8<br>Orange 599 0.616 0.370 10.4<br>Violet – 0.217 0.089 8.3<br>Spring Green 508 0.177 0.536 14.6<br>**----- End of picture text -----**<br>


## FCC Part 15 Class B for Unintentional Radiators 

(Part 15.105(b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

- Reorient or relocate the receiving antenna. 

- Increase the separation between the equipment and receiver. 

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

- Consult the dealer or an experienced radio/TV technician for help. 

(Part 15.21) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. 

## Industry Canada ICES-003(B) 

This device complies with CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and 2) This device must accept any interference received, including interference that may cause undesired operation. 

Cet appareil est conforme à la norme NMB-3(B). Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne peut pas occasionner d'interférences, et (2) il doit tolérer toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité du dispositif. 

## Dimensions 

All measurements are listed in millimeters [inches], unless noted otherwise. The measurements provided are subject to change. 

**==> picture [245 x 115] intentionally omitted <==**

**----- Start of picture text -----**<br>
36.3 mm<br>[1.43”]<br>56.3 mm<br>[2.22”]<br>68.3 mm<br>[2.69”]<br>Ø50.0 mm M30 × 1.5<br>[1.97”]<br>M12 × 1<br>**----- End of picture text -----**<br>


- (3) Refer to the CIE 1931 (x,y) Chromaticity Diagram to show equivalent color with indicated color coordinates. Actual coordinates may differ ± 5%. 

page 4 of 8 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

17-Jun-25 

K50 Pro with Optical Sensor 

## Accessories 

## Pro Editor Hardware 

## PRO-KIT 

Includes: 

- Pro Converter Cable (MQDC-506-USB) 

- • Splitter (CSB-M1251FM1251M) • Power Supply (PSW-24-1) 

**==> picture [58 x 39] intentionally omitted <==**

## MQDC-506-USB 

- Pro Converter Cable 

- • 1.83 m (6 ft) length 5-pin M12 quick disconnect to Device and USB to PC • Required for connection to the configuration software 

**==> picture [91 x 38] intentionally omitted <==**

## CSB-M1251FM1251M 

- 5-pin parallel Y splitter (Male-Male-Female) 

- • For full Pro Editor preview capability • Requires external power supply, sold separately 

## PSW-24-1 

- 24 V DC, 1 A power supply 

- • 2 m (6.5 ft) PVC cable with M12 quick disconnect • Provides external power with splitter cable, sold separately 

## ACC-PRO-CABLE5 

- Mating accessory for cabled and terminal models 

- • 150 mm (6 inch) PVC cable with M12 quick disconnect • Lever wire nuts included (qty 5) • Required to connect cabled models and screw terminal models to Pro Converter Cable, sold separately 

**==> picture [10 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
x5<br>**----- End of picture text -----**<br>


## MQDC-801-5M-PRO 

- 8-pin to 5-pin double-ended cordset 

- 0.31 m (1 ft) PVC cable with M12 quick disconnects 

- • Required to connect 8-pin Pro Series-enabled devices to Pro Converter Cable (MQDC-506USB), sold separately 

## Cordsets 

**==> picture [500 x 152] intentionally omitted <==**

**----- Start of picture text -----**<br>
5-Pin Single-Ended M12 Female Cordsets<br>Model  Length  Style  Dimensions  Pinout (Female)<br>MQDC1-501.5 0.5 m (1.5 ft)<br>2<br>MQDC1-503 0.9 m (2.9 ft)  1<br>MQDC1-506 2 m (6.5 ft)  44 Typ. 3<br>MQDC1-515 5 m (16.4 ft)  4 5<br>MQDC1-530 9 m (29.5 ft)  Straight  M12 x 1 1 = Brown 2 = White<br>3 = Blue<br>MQDC1-560 18 m (59 ft)  ø 14.5 4 = Black<br>5 = Gray<br>MQDC1-5100 31 m (101.7 ft)<br>Continued on page 6<br>**----- End of picture text -----**<br>


© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

page 5 of 8 

17-Jun-25 

K50 Pro with Optical Sensor 

**==> picture [500 x 629] intentionally omitted <==**

**----- Start of picture text -----**<br>
Continued from page 5<br>5-Pin Single-Ended M12 Female Cordsets<br>Model  Length  Style  Dimensions  Pinout (Female)<br>MQDC1-506RA 2 m (6.5 ft)<br>32 Typ.<br>MQDC1-515RA 5 m (16.4 ft)  [1.26"]<br>MQDC1-530RA 9 m (29.5 ft)<br>30 Typ.<br>Right-Angle  [1.18"]<br>MQDC1-560RA 19 m (62.3 ft)<br>M12 x 1<br>ø 14.5 [0.57"]<br>5-Pin Single-Ended M12 Female Stainless Steel Washdown Cordsets<br>Model  Length  Style  Dimensions  Pinout (Female)<br>MQDC-WDSS-0506 2 m (6.56 ft)  2<br>1<br>MQDC-WDSS-0515 5 m (16.4 ft)<br>3<br>Ø15.5 mm 4 5<br>Straight<br>Ø4.8 mm 1 = Brown<br>MQDC-WDSS-0530 9 m (29.5 ft)  2 = White<br>43.5 mm 3 = Blue<br>4 = Black<br>5 = Gray<br>8-Pin Single-Ended M12 Female Open-Shielded Cordsets<br>Model  Length  Style  Dimensions  Pinout (Female)<br>MQDC2S-806 2.04 m (6.7 ft)<br>44 Typ.<br>MQDC2S-815 5.04 m (16.54 ft)<br>MQDC2S-830 10.04 m (32.95 ft)<br>Straight  2<br>3<br>M12 x 1<br>MQDC2S-850 16 m (52.49 ft)  ø 14.5 1 4<br>7<br>5<br>6<br>MQDC2S-806RA 2 m (6.56 ft)  32 Typ. 8<br>[1.26"]<br>MQDC2S-815RA 5 m (16.4 ft)  1 = White<br>2 = Brown<br>MQDC2S-830RA 10 m (32.81 ft)  3 = Green<br>30 Typ. 4 = Yellow<br>Right-Angle  [1.18"] 5 = Gray 6 = Pink<br>7 = Blue<br>8 = Red<br>MQDC2S-850RA 16 m (52.49 ft)  M12 x 1<br>ø 14.5 [0.57"]<br>8-Pin Single-Ended M12 Female Open-Shielded, Washdown, Stainless Steel Cordsets<br>Model  Length  Style  Dimensions  Pinout (Female)<br>MQDC-WDSS-0806 2 m (6.56 ft)  2<br>3<br>44 Typ. 1 4<br>MQDC-WDSS-0815 5 m (16.4 ft)  7 5<br>6<br>Straight  8<br>M12 x 1<br>ø 14.5<br>1 = White  5 = Gray<br>2 = Brown  6 = Pink<br>MQDC-WDSS-0830 9 m (29.53 ft)  3 = Green  7 = Blue<br>4 = Yellow  8 = Red<br>**----- End of picture text -----**<br>


page 6 of 8 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

17-Jun-25 

K50 Pro with Optical Sensor 

## Brackets 

**==> picture [500 x 612] intentionally omitted <==**

**----- Start of picture text -----**<br>
45<br>SMB30A<br>• Right-angle bracket with curved slot for versatile orientation<br>•• Clearance for M6 (¼ in) hardwareMounting hole for 30 mm sensor 61 C<br>• 12-gauge stainless steel B<br>A<br>Hole center spacing:  A to B=40<br>Hole size:  A=ø 6.3, B= 27.1 × 6.3, C=ø 30.5 69<br>SMB30FA 83.2<br>• Swivel bracket with tilt and pan movement for precise adjustment<br>• Mounting hole for 30 mm sensor<br>• 12-gauge 304 stainless steel<br>• Easy sensor mounting to extrude rail T-slot<br>• Metric- and inch-size bolt available 36.3 B 68.9<br>A<br>Bolt thread:  SMB30FA, A= 3/8 - 16 × 2 in; SMB30FAM10, A= M10 - 1.5 × 50<br>Hole size:  B= ø 30.1<br>SMB30FVK 46<br>• V-clamp, flat bracket and fasteners for mounting to pipe or extensions 118<br>•• Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions30 mm hole for mounting sensors A<br>Hole size:  A= ø 31<br>70 57<br>SMB30MM<br>• 12-gauge stainless steel bracket with curved mounting slots for versatile orientation<br>• Clearance for M6 (¼ in) hardware C<br>• Mounting hole for 30 mm sensor 57<br>B<br>Hole center spacing:  A = 51, A to B = 25.4<br>Hole size:   A = 42.6 × 7, B = ø 6.4, C = ø 30.1<br>A<br>A<br>SMB30RAVK<br>• V-clamp, right-angle bracket and fasteners for mounting sensors to pipe or extrusion<br>• Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions 46<br>• 30 mm hole for mounting sensors<br>Hole size:  A = ø 30.5 57 90<br>67<br>SMB30SC<br>• Swivel bracket with 30 mm mounting hole for sensor B<br>•• Black reinforced thermoplastic polyesterStainless steel mounting and swivel locking hardware included 58<br>Hole center spacing:  A=ø 50.8<br>Hole size:  A=ø 7.0, B=ø 30.0 29<br>A<br>45<br>SMBAMS30P<br>• Flat SMBAMS series bracket C<br>• 30 mm hole for mounting sensors<br>• Articulation slots for 90°+ rotation A<br>• 12-gauge 300 series stainless steel 93<br>B<br>Hole center spacing:  A=26.0, A to B=13.0<br>Hole size:  A=26.8 × 7.0, B=ø 6.5, C=ø 31.0<br>**----- End of picture text -----**<br>


© Banner Engineering Corp. All rights reserved. 

page 7 of 8 

17-Jun-25 

www.bannerengineering.com 

K50 Pro with Optical Sensor 

## SMBAMS30RA 

- Right-angle SMBAMS series bracket 

- • 30 mm hole for mounting sensors • Articulation slots for 90°+ rotation • 12-gauge (2.6 mm) cold-rolled steel 

- Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 × 7.0, B=ø 6.5, C=ø 31.0 

## TC-K50-CL 

- Touch cover 

**==> picture [77 x 118] intentionally omitted <==**

**----- Start of picture text -----**<br>
45<br>C<br>53 A<br>B<br>48<br>Ø A<br>B<br>**----- End of picture text -----**<br>


Diameter: A = 67 mm Height: B = 42.5 mm 

## Banner Engineering Corp Limited Warranty 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. 

For patent information, see www.bannerengineering.com/patents. 

page 8 of 8 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

17-Jun-25