K50BCLS1XBXPQ

EZ-LIGHT® K50 Rotating and Strobing Beacon 

## Features 

Daylight-visible, general-purpose indicators for indoor or outdoor use 

- Intense levels of light output for areas with high ambient light - even outdoors 

- • Viewable around entire perimeter; strobing models also emit light from top • Rotating and strobing models • Rugged, sealed thermoplastic housing rated for IP67 and IP69K per DIN 40050-9 • Bright, even light • 12 V DC to 30 V DC operation • 12 V DC operation useful for applications on mobile vehicles 

## WARNING: 

- Do not use this device for personnel protection 

- Using this device for personnel protection could result in serious injury or death. 

- This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition. 

## Models 

**==> picture [465 x 315] intentionally omitted <==**

**----- Start of picture text -----**<br>
Model  [(1)] Function Connection LED Color Input Voltage<br>K50BLR1XGXPQ Green<br>K50BLR1XRXPQ Red<br>Rotating<br>K50BLR1XYXPQ Yellow<br>K50BLR1XBXPQ Integral 5-pin M12 male quick-disconnect  Blue 12 V DC to 30 V DC<br>K50BCLS1XGXPQ connector Green<br>K50BCLS1XRXPQ Red<br>Strobing<br>K50BCLS1XYXPQ Yellow<br>K50BCLS1XBXPQ Blue<br>Wiring<br>Wire Color Function for Rotating Models Function for Strobing Models<br>Blue (3) 0 V DC Common Common<br>Black (4) +V DC ON continuous ON continuous<br>Brown (1) +V DC Rotating at 90 rpm Single pulse strobe at 1 Hz<br>White (2) +V DC Rotating at 180 rpm Double pulse strobe at 1 Hz<br>Integral 5-pin M12 male quick-disconnect<br>PNP Input connector Wiring Key<br>bu (3)<br>12–30 V DC 1<br>bn (1)<br>wh (2) 2 1 = Brown2 = White<br>bk (4) 4 3 = Blue4 = Black<br>r REY @ 5 = Gray (Not Used)<br>gy (5) 3 5<br>**----- End of picture text -----**<br>


## Wiring 

- (1) 

- To order the 150 mm (6 in) PVC-jacketed cable with a 5-pin M12 male quick-disconnect connector model, replace Q with QP in model number (example, K50BLR1XGXPQP ). 

- To order the 2 m (6.5 ft) cable model, omit suffix Q from model number (example, K50BLR1XGXP ). 

- Models with a quick-disconnect connector require a mating cable (refer to the Accessories list). 

Original Instructions 30-Jun-25 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

p/n: 159966 Rev. G 

EZ-LIGHT® K50 Rotating and Strobing Beacon 

_Timing diagram for 1 pulse or 2 pulses_ 30 ms 1 sec 1-Pulse Strobe eee 0 70 ms 30 ms 30 ms 1 sec 2-Pulse Strobe JrIR {. —Il 

## Specifications 

Supply Voltage and Current 

**==> picture [311 x 164] intentionally omitted <==**

**----- Start of picture text -----**<br>
Application Note<br>12 V DC to 30 V DC Light emits 360° from housing sides and from<br>Rotating models:  140 mA maximum at 12 V DC, 70  housing top, some models<br>mA maximum at 30 V DC<br>Rotating Models Strobing Models<br>Strobing models:  160 mA maximum at 12 V DC,<br>100 mA maximum at 30 V DC<br>Protected against reverse polarity and transient<br>voltages<br>LED function depends on the model and wiring  LIGHT DIRECTION LIGHT DIRECTION<br>(see )<br>Indicator Power-Up Response Time Vibration and Mechanical Shock<br>ON:  250 ms<br>All models meet Mil. Std. 202F requirements<br>method 201A (vibration: 10 to 60 Hz max., double<br>Base and covers: polycarbonate amplitude 0.06", maximum acceleration 10G). Also<br>meets IEC 947-5-2; 30G 11 ms duration, half sine<br>wave.<br>Integral 5-pin M12 male quick-disconnect  Certifications<br>**----- End of picture text -----**<br>


Supply Protection Circuitry 

Indicators 

Indicator Power-Up Response Time 

Construction 

## Connections 

Integral 5-pin M12 male quick-disconnect connector, 150 mm (6 in) PVC-jacketed cable with a 5-pin M12 male quick-disconnect connector, or 2 m (6.5 ft) integral cable, depending on model 

**==> picture [85 x 24] intentionally omitted <==**

**----- Start of picture text -----**<br>
Banner Engineering BV<br>Park Lane, Culliganlaan 2F bus 3<br>1831 Diegem, BELGIUM<br>**----- End of picture text -----**<br>


Operating Conditions 

–40 °C to +50 °C (–40 °F to +122 °F) 

- 90% at +50 °C maximum relative humidity (noncondensing) 

**==> picture [127 x 82] intentionally omitted <==**

**----- Start of picture text -----**<br>
Required Overcurrent Protection<br>WARNING:  Electrical<br>connections must be<br>made by qualified<br>personnel in<br>accordance with local<br>and national electrical<br>codes and<br>regulations.<br>**----- End of picture text -----**<br>


Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to www.bannerengineering.com. 

**==> picture [125 x 57] intentionally omitted <==**

**----- Start of picture text -----**<br>
Supply  Required  Supply  Required<br>Wiring  Overcurrent  Wiring  Overcurrent<br>(AWG) Protection (A) (AWG) Protection (A)<br>20 5.0 26 1.0<br>22 3.0 28 0.8<br>24 1.0 30 0.5<br>**----- End of picture text -----**<br>


Environmental Rating 

Rated IP67 and IP69K per DIN 40050 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

page 2 

30-Jun-25 

EZ-LIGHT® K50 Rotating and Strobing Beacon 

## Dimensions 

All measurements are listed in millimeters [inches], unless noted otherwise. The measurements provided are subject to change. 

**==> picture [281 x 233] intentionally omitted <==**

**----- Start of picture text -----**<br>
50<br>[ 1.97 ]<br>29<br>[1.14]<br>49<br>[1.93]<br>11<br>[.43]<br>M12<br>**----- End of picture text -----**<br>


## Accessories 

## Cordsets 

**==> picture [500 x 271] intentionally omitted <==**

**----- Start of picture text -----**<br>
4-Pin Single-Ended M12 Female Cordsets<br>Model  Length  Style  Dimensions  Pinout (Female)<br>MQDC-406 2 m (6.56 ft)  44 Typ.<br>MQDC-415 5 m (16.4 ft)<br>MQDC-430 9 m (29.5 ft)  2<br>1<br>M12 x 1<br>Straight  ø 14.5 3<br>Ø5.2 mm 4 5<br>MQDC-450 15 m (49.2 ft)<br>7 mm<br>58 mm 1 = Brown<br>2 = White<br>3 = Blue<br>MQDC-406RA 2 m (6.56 ft)  32 Typ. 4 = Black<br>MQDC-415RA 5 m (16.4 ft)  [1.26"] 5 = Not used<br>MQDC-430RA 9 m (29.5 ft)<br>30 Typ. 2<br>[1.18"] 3<br>1<br>Right-Angle  4<br>M12 x 1<br>MQDC-450RA 15 m (49.2 ft)  ø 14.5 [0.57"]<br>Ø5.2 mm<br>7 mm<br>58 mm<br>**----- End of picture text -----**<br>


© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

30-Jun-25 

page 3 

EZ-LIGHT® K50 Rotating and Strobing Beacon 

## LMB Sealed Right-Angle Bracket 

- Model Description • Direct-Mount Models 

- LMB30RA - Black polycarbonate • Bracket kit with base, 30 mm adapter, set screw, LMB30RAC - Gray polycarbonate fasteners, O-rings, and gaskets. • Pipe-Mount Models 

- LMBE12RA - Black polycarbonate • Bracket kit with base, ½-14 pipe adapter, set screw, LMBE12RAC - Gray polycarbonate • fasteners, O-rings, and gasketsFor use with stand-off pipe (listed and sold separately) 

**==> picture [149 x 59] intentionally omitted <==**

## Mounting Brackets 

All measurements are listed in millimeters, unless noted otherwise. The measurements provided are subject to change. 

- 45 

- SMB30A • Right-angle bracket with curved slot for versatile orientation C • Clearance for M6 (¼ in) hardware 61 • Mounting hole for 30 mm sensor • 12-gauge stainless steel B A 

- Hole center spacing: A to B=40 Hole size: A=ø 6.3, B= 27.1 × 6.3, C=ø 30.5 69 

- SMB30FA 83.2 • Swivel bracket with tilt and pan movement for precise adjustment • Mounting hole for 30 mm sensor • 12-gauge 304 stainless steel • Easy sensor mounting to extrude rail T-slot • Metric- and inch-size bolt available 36.3 B 68.9 A 

- Bolt thread: SMB30FA, A= 3/8 - 16 × 2 in; SMB30FAM10, A= M10 - 1.5 × 50 Hole size: B= ø 30.1 70 57 

- SMB30MM • 12-gauge stainless steel bracket with curved mounting slots for versatile orientation • Clearance for M6 (¼ in) hardware C • Mounting hole for 30 mm sensor 57 B 

- Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 × 7, B = ø 6.4, C = ø 30.1 A 67 

- SMB30SC • Swivel bracket with 30 mm mounting hole for sensor B • Black reinforced thermoplastic polyester 58 • Stainless steel mounting and swivel locking hardware included 

- Hole center spacing: A=ø 50.8 Hole size: A=ø 7.0, B=ø 30.0 29 A 

- 55 

- LMBE12RA35 35 38.25 • Direct mounting of stand-off pipe, with common bracket type • Zinc-plated steel • 1/2-14 NPSM nut • Mounting distance from the wall to the center of the 1/2-14 NPSM nut is 35 mm 57 

- Hole center spacing: 20.0 2X Ø9 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

30-Jun-25 

page 4 

EZ-LIGHT® K50 Rotating and Strobing Beacon 

## LMBE12RA45 

- Direct mounting of stand-off pipe, with common bracket type 

- • Zinc-plated steel • 1/2-14 NPSM nut • Mounting distance from the wall to the center of the 1/2-14 NPSM nut is 45 mm 

Hole center spacing: 35.0 

**==> picture [65 x 81] intentionally omitted <==**

**----- Start of picture text -----**<br>
65<br>45<br>38.25<br>81<br>2X Ø11<br>**----- End of picture text -----**<br>


## Elevated Mount System 

Model Description Components SA-M30TE12 - Black Acetal • Streamlined black acetal or white UHMW stand-off pipe adapter/cover • Connects between 30 mm light base and ½ in. NPSM/ SA-M30TE12C - White UHMW DN15 pipe • Mounting hardware included Polished 304 Stainless Black Anodized Aluminum Clear Anodized Aluminum Steel SOP-E12-150SS SOP-E12-150A SOP-E12-150AC •• Elevated-use stand-off pipe (½ in. NPSM/DN15)Polished 304 stainless steel, black anodized aluminum, 150 mm (6 in) long 150 mm (6 in) long 150 mm (6 in) long or clear anodized aluminum surface • ½ in. NPT thread at both ends: one end screws into the SOP-E12-300SS SOP-E12-300A SOP-E12-300AC internal threads of the light's base, and one end screws into the mounting base adapter/cover 300 mm (12 in) long 300 mm (12 in) long 300 mm (12 in) long • Compatible with most industrial environments SOP-E12-900SS SOP-E12-900A SOP-E12-900AC 900 mm (36 in) long 900 mm (36 in) long 900 mm (36 in) long SA-E12M30 - Black Acetal • Streamlined black acetal or white UHMW mounting base adapter/cover • Connects between ½ in. NPSM/DN15 pipe and 30 mm SA-E12M30C - White UHMW (1-3/16 in) drilled hole 

- Streamlined black acetal or white UHMW mounting base adapter/cover 

- • Connects between ½ in. NPSM/DN15 pipe and 30 mm (1-3/16 in) drilled hole 

- • Mounting hardware included 

## Banner Engineering Corp Limited Warranty 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. 

For patent information, see www.bannerengineering.com/patents. 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

30-Jun-25 

page 5