K3MA-L-C 24VAC/DC

**Temperature Meter K3MA-L** 

CSM_K3MA-L_DS_E_11_1 

## **Highly Visible LCD Display with 2-color (Red and Green) LEDs** 

- Wide input range - select from two types of platinum-resistance thermometers and ten types of thermocouples. 

- Front-panel key operation for easy setting. 

- Average processing function suppresses flicker. 

- Temperature input shift and temperature unit selection functions. 

- Easy confirmation of max/min display. 

- Short 80-mm depth (measured from edge of face plate). 

- Finger protective cover (standard equipment) protects against electric shock. 

- Water- and dust-proof NEMA4X (IP66 equivalent) front panel. 

- Recognized to conform to U.S. and Canadian requirements under the Component Recognition Program of UL. 

For the most recent information on models that have been certified for safety standards, refer to your OMRON website. 

- CE marking. 

Refer to _Safety Precautions for All Digital Panel Meters_ . 

## **Model Number Structure** 

## ■ **Model Number Legend** 

## K3MA-L ~~~~~ -@ ~~EJ~~ 

**1 2 3** 

## **1. Input Type** 

- L: Platinum-resistance thermometer or thermocouple 

## **2. Output Type** 

## **3. Supply Voltage** 

   - 100-240VAC: 100 to 240 VAC 24VAC/VDC: 24 VAC/VDC 

- None: No output 

- C: With relay contact output (SPDT) 

## **Orderin Information g** 

## ■ **List of Models** 

|■**List of Models**||||
|---|---|---|---|
|**Input type**|**Supply voltage**|**Output**|**Model**|
|Platinum-resistance thermometer or thermo-<br>couple|100 to 240 VAC|None|K3MA-L 100-240VAC|
|||1 relay contact output (SPDT)|K3MA-L-C 100-240VAC|
||24 VAC/VDC|None|K3MA-L 24VAC/VDC|
|||1 relay contact output (SPDT)|K3MA-L-C 24VAC/VDC|



**1** 

**K3MA-L** 

## ■ **Accessories (Order Separately)** 

|**Name**|**Name**|**Shape**|**Shape**|**Model**|
|---|---|---|---|---|
|Splash-proof Soft Cover||||K32-49SC|
|Hard Cover||||K32-49HC|
|Watertight Cover||||Y92A-49N|
|Rubber Packing||||K32-P1|
|**Note:**Rubber packing is provided with the Controller.<br>**Specifications**|||||
|■**Ratings**|||||
||**K3MA-L 100-240VAC, K3MA-L-C 100-240VAC**||**K3MA-L 24VAC/VDC, K3MA-L-C 24VAC/VDC**||
|**Supply voltage**|100 to 240 VAC||24 VAC (50/60 Hz), 24 VDC||
|**Operating voltage range**|85% to 110% of the rated supply voltage||||
|**Power consumption**<br>**(under maximum load)**|6 VA max.||4.5 VA max. (24 VAC)<br>4.5 W max. (24 VDC)||
|**Insulation resistance**|20 MΩmin. (at 500 VDC) between external terminal and case.<br>Insulation provided between inputs, outputs, and power supply.||||
|**Dielectric strength**|2,000 VAC for 1 min between external terminal and case.<br>Insulation provided between inputs, outputs, and power supply.||||
|**Noise immunity**|±1,500 V on power supply terminals in normal or com-<br>mon mode.<br>±1μs, or 100 ns for square-wave noise with 1 ns.||±480 V on power supply terminals in normal mode.<br>±1,500 V in common mode.<br>±1μs, or 100 ns for square-wave noise with 1 ns.||
|**Vibration resistance**|Vibration: 10 to 55 Hz, Acceleration: 50 m/s2<br>5 min each in X, Y, and Z directions for 10 sweeps.||||
|**Shock resistance**|150 m/s2(100 m/s2for relaycontact outputs) 3 times each on 3 axes, 6 directions.||||
|**Ambient temperature**|Operating:−10°C to 55°C (with no condensation or icing)<br>Storage:<br>−25°C to 65°C (with no condensation or icing)||||
|**Ambient humidity**|Operating: 25% to 85% (with no condensation)||||
|**Approved safety standards**|UL61010-1, CSA C22.2 No.61010-1-04, conforms to EN61010-1 (Pollution degree 2/overvoltage category II)<br>Conforms to VDE0106/P100 (finger protection)||||
|**EMC**|(EMI)<br>EN61326-1<br>Industrial electromagnetic environment<br>Emission Enclosure:<br>CISPR 11 Group 1 class A<br>Emission AC Mains:<br>CISPR 11 Group 1 class A<br>(EMS)<br>EN61326-1<br>Industrial electromagnetic environment<br>Immunity ESD:<br>EN61000-4-2:<br>4 kV contact discharge<br>8 kV air discharge<br>Immunity RF-interference:<br>EN61000-4-3:<br>10 V/m (amplitude-modulated, 80 MHz to 1 GHz)<br>Electrical Fast Transient Noise:<br>EN61000-4-4:<br>2 kV (power line)<br>Immunity Burst Noise:<br>1 kV line to line (I/O signal line)<br>Immunity Surge:<br>EN61000-4-5:<br>1 kV (power line)<br>2 kV line to ground (power line)<br>Immunity Conducted Disturbance:<br>EN61000-4-6:<br>3 V (0.15 to 80 MHz)<br>ImmunityVoltage Dip/Interrupting:<br>EN61000-4-11: 0.5 cycle, 0, 180°,100%(rated voltage)||||
|**Weight**|Approx. 200g||||



**2** 

**K3MA-L** 

## ■ **Characteristics** 

|■**Characteristics**||
|---|---|
|**Indication accuracy (at 23**±**5**°**C)**<br>**(See note.)**|Thermocouple:<br>(±0.5% of indication value or±1°C, whichever greater)±1 digit max.<br>Platinum-resistance thermometer:<br>(±0.5% of indication value or±1°C, whichevergreater)±1 digit max.|
|**Input**|Thermocouple: K, J, T, E, L, U, N, R, S, B<br>Platinum-resistance thermometer: JPt100, Pt100|
|**Measurement method**|Double integral method|
|**Sampling period**|500 ms|
|**Display refresh period**|Samplingperiod (samplingtimes multiplied by number of averagingtimes if average processingis selected.)|
|**Max. displayed digits**|4 digits (−1999 to 9999)|
|**Display**|7-segment digital display, Character height: 14.2 mm|
|**Polarity display**|“−” is displayed automatically with a negative input signal.|
|**Zero display**|Leading zeros are not displayed.|
|**Input shift**|Input shift equivalent to the settingvalue supported for all points within the sensor measurement range.|
|**Hold function**|Max hold (maximum value), Min hold (minimum value)|
|**Hysteresis setting**|Programmable with front-panel key inputs (0001 to 9999).|
|**Other functions**|Display color change (green (red), green, red (green), red)<br>Average processing (simple average OFF/2/4/8 operations)<br>Setting change lockout<br>Parameter initialization|
|**Output**|Relay contact (SPDT)|
|**Delay in comparative outputs**|1 s max.|
|**Degree of protection**|Front panel: NEMA4X for indoor use (equivalent to IP66)<br>Rear case:<br>IEC standard IP20<br>Terminals:<br>IEC standard IP00 + finger protection (VDE0106/100)|
|**Memory protection**|Non-volatile memory (EEPROM) (possible to rewrite 100,000 times) (with terminal cover attached)|



**Note:** The indication accuracy of the K thermocouple at a temperature of − 200 to 1300 ° C is ± 2 ° C ± 1 digit maximum. The indication accuracy of the T and N thermocouples at a temperature of − 100 ° C or less is ± 2 ° C ± 1 digit maximum. The indication accuracy of the U and L thermocouples at any temperature is ± 2 ° C ± 1 digit maximum. The indication accuracy of the B thermocouple at a temperature of 400 ° C or less is unrestricted. The indication accuracy of the R and S thermocouples at a temperature of 200 ° C or less is ± 3 ° C ± 1 digit maximum. 

## ■ **Measuring Ranges** 

## **Platinum-resistance Thermometer** 

|**Input**|**Input**|**Pt100**|**Pt100**|**Pt100**|**JPt100**|**JPt100**|
|---|---|---|---|---|---|---|
|Range|°C<br>|−200 to 850|−199.9 to 500.0|0.0 to 100.0|−199.9 to 500.0|0.0 to 100.0|
||°F<br>|−300 to 1500|−199.9 to 900.0|0.0 to 210.0|−199.9 to 900.0|0.0 to 210.0|
|Parameter||0|1|2|3|4|



## **Thermocouple** 

|**Input**|**Input**|**K**|**K**|**J**|**J**|**T**|**T**|**E**|**L**|**U**|**U**|**N**|**R**|**S**|**B**|
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|Range|°C|−200<br>to<br>1300|−20.0<br>to<br>500.0|−100<br>to<br>850|−20.0<br>to<br>400.0|−200<br>to<br>400|−199.9<br>to<br>400.0|0<br>to<br>600|−100<br>to<br>850|−200<br>to<br>400|−199.9<br>to<br>400.0|−200<br>to<br>1300|0<br>to<br>1700|0<br>to<br>1700|100<br>to<br>1800|
||°F|−300<br>to<br>2300|0.0<br>to<br>900.0|−100<br>to<br>1500|0.0<br>to<br>750|−300<br>to<br>700|−199.9<br>to<br>700.0|0<br>to<br>1100|−100<br>to<br>1500|−300<br>to<br>700|−199.9<br>to<br>700.0|−300<br>to<br>2300|0<br>to<br>3000|0<br>to<br>3000|300<br>to<br>3200|
|Parameter||5|6|7|8|9|10|11|12|13|14|15|16|17|18|



## ■ **Input/Output Ratings** 

## **Relay Contact Output** 

|**Relay Contact Output**|||
|---|---|---|
|**Item**|**Resistive load (cos**φ**= 1)**|**Inductive load (cos**φ**= 0.4, L/R = 7 ms)**|
|**Rated load (UL ratings)**|5 A at 250 VAC, 5 A at 30 VDC|1.5 A at 250 VAC, 1.5 A at 30 VDC|
|**Min. permissible load**<br>**(P level, reference value)**|10 mA at 5 VDC||
|**Mechanical life**|20,000,000 times min.||
|**Electrical life**|100,000 times min.||



**3** 

**K3MA-L** 

## **Connections** 

## ■ **Terminal Arrangement** 

**==> picture [512 x 204] intentionally omitted <==**

**----- Start of picture text -----**<br>
Models with<br>A1 comparative  E1<br>output<br>Power<br>A2 OUT1 E2<br>supply Output  100- to 240-VAC type or<br>terminals 24-VAC/VDC type E3<br>(No polarity for 24-VDC<br>connection.) E4 E4 A<br>Input<br>terminals + B<br>E5 E5<br>B<br>E6 − E6<br>For thermocouple  For platinum-<br>input resistance<br>thermometer input<br>Terminal No. Name Description<br>A1 - A2 Operation power Connects the operation power supply.<br>E4 - E6 - E5 Thermocouple or platinum-resistance ther-mometer input Connects the thermocouple or platinum-resis-tance thermometer input.<br>E1 , E2 - E3 Outputs Outputs the relay outputs.<br>**----- End of picture text -----**<br>


## ■ **Block Diagram** 

**==> picture [266 x 166] intentionally omitted <==**

**----- Start of picture text -----**<br>
Key<br>Input Input<br>Micro-<br>computer Display<br>EEPROM Output circuit X Contact output (See<br>note.)<br>5 V 12 V<br>Constant voltage circuit<br>Power supply circuit<br>**----- End of picture text -----**<br>


**Note:** Relay output models only. 

**4** 

**K3MA-L** 

## **O eration p** 

## ■ **Main Functions** 

## **Input Types and Ranges** 

|**Parameter**|**Setting**|**Input type**||**Meaning**|**Meaning**|
|---|---|---|---|---|---|
|in-t|0|Platinum-resistance<br>thermometer|Pt100|−200 to 850°C|−300 to 1500°F|
||1|||−199.9 to 500.0°C|−1999 to 900.0°F|
||2|||0.0 to 100.0°C|0.0 to 210.0°F|
||3||JPt100|−199.9 to 500.0°C|−199.9 to 900.0°F|
||4|||0.0 to 100.0°C|0.0 to 210.0°F|
||5|Thermocouple|K|−200 to 1300°C|−300 to 2300°F|
||6|||−20.0 to 500.0°C|0.0 to 900.0°F|
||7||J|−100 to 850°C|−100 to 1500°F|
||8|||−20.0 to 400.0°C|0.0 to 750.0°F|
||9||T|−200 to 400°C|−300 to 700°F|
||10|||−199.9 to 400.0°C|−199.9 to 700.0°F|
||11||E|0 to 600°C|0 to 1100°F|
||12||L|−100 to 850°C|−100 to 1500°F|
||13||U|−200 to 400°C|−300 to 700°F|
||14|||−199.9 to 400.0°C|−199.9 to 700.0°F|
||15||N|−200 to 1300°C|−300 to 2300°F|
||16||R|0 to 1700°C|0 to 3000°F|
||17||S|0 to 1700°C|0 to 3000°F|
||18||B|100 to 1800°C|300 to 3200°F|



**Note:** The initial value is “ 5: thermocouple K ( − 200 to 1300 ° C/ − 300 to 2300 ° F).” 

## **Temperature Unit Selection** 

Either centigrade ( ° C) or fahrenheit ( ° F) can be selected as the temperature unit. 

|<br>perature unit.|||
|---|---|---|
|**Parameter**|**Setting**|**Meaning**|
|d-u<br><br>|c|Displayin°C.|
||f|Displayin°F.|



## **OUT Types (Comparative Output Models Only)** 

OUT 1 can be set to operate in one of the three following modes in accordance with the compared values: 

- Upper limit (High Acting): The output is turned ON when the measurement value is greater than its set value. 

- Lower limit (Low Acting): 

The output is turned ON when the measurement value is less than its set value. 

- Upper and lower limits (Outside Band Acting): An upper limit (H set value) and lower limit (L set value) can be set independently. 

The output is turned ON when the measurement value is greater than the upper-limit set value or less than the lower-limit set value. 

|**Parameter**|**Setting**|**Meaning**|
|---|---|---|
|out 1.t|hi|Upper limit: Alarm op-<br>erates at upper limit.|
||lo|Lower limit: Alarm op-<br>erates at lower limit.|
||hi-lo|Upper and lower lim-<br>its: Alarm operates at<br>upper and lower lim-<br>its.|



## **Upper Limit (High Acting)** 

## **Lower Limit (Low Acting)** 

## **Upper and Lower Limits (Outside Band Acting)** 

**==> picture [484 x 72] intentionally omitted <==**

**----- Start of picture text -----**<br>
OUT1 value Hysteresis OUT1 upper-limit value Hysteresis<br>Measurement<br>Measurement<br>value<br>Measurement value OUT1 value Hysteresis valueOUT1 lower-limit  Hysteresis<br>value<br>Output ON Output ON Output ON<br>OFF OFF OFF<br>**----- End of picture text -----**<br>


**5** 

**K3MA-L** 

## **Temperature Input Shift** 

## **Changing the Display Color** 

Input shift equivalent to the setting value supported for all points within the sensor measurement range. 

The color of the value displayed can be set to either red or green. For comparative output models, the display color can be set to change from green to red, or from red to green, according to the status of the comparison criterion. 

**==> picture [511 x 145] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Setting comparison criterion.<br>ins -1999  to  9999<br>Red<br>258.9<br>Temperature<br>OUT1 value<br>Green<br>Before shift<br>192.0<br>After shift<br>Temperature input<br>shift value Display Auto-return Time<br>Input This function automatically returns the display to the operation level’s<br>ae a<br>current value if no keys are pressed for a preset time (called the dis-<br>play auto-return time).<br>**----- End of picture text -----**<br>


## **Parameter Initialization** 

## **Move-to-Protect-Level Time** 

This function returns all of the parameters to their initial values. 

The time required to shift to the protect level can be set as desired. 

|**Parameter**|**Setting**|**Meaning**|
|---|---|---|
|init|off|---|
||on|Initializes all parame-<br>ters.|



## **MAX/MIN Display** 

The maximum and minimum measurement (display) values from the time the power is turned ON until the current time can be stored and displayed. This is useful, for example, when measuring the maximum value. 

Use this to reset the K3MA-L after returning it to its factory-set condition. 

## **Average Processing** ~~a~~ 

**==> picture [107 x 132] intentionally omitted <==**

**----- Start of picture text -----**<br>
Current value<br>MAX/MIN<br>SHIFT UP “=<br>MAX value<br>MAX/MIN<br>SHIFT UP<br>MIN value<br>) ) =<br>Ee»<br>MAX/MIN<br>**----- End of picture text -----**<br>


Average processing stabilizes displayed values to minimize flicker by averaging the fluctuating input signals. Average processing can be performed for the measurement values in either of four steps (OFF, 2 times, 4 times, or 8 times). 

This is useful for ignoring rapid fluctuations, e.g., eliminating spike noise. 

## **Hysteresis (Comparative Output Models Only)** 

The hysteresis of comparative outputs can be set to prevent chattering in the output when the measurement value fluctuates finely near the OUT value. 

**Upper limit (high acting)** 

**==> picture [129 x 82] intentionally omitted <==**

**----- Start of picture text -----**<br>
Set value<br>Hysteresis<br>Measurement value<br>ON<br>Output F<br>OFF<br>**----- End of picture text -----**<br>


**6** 

**K3MA-L** 

## **Nomenclature** 

|**K3MA-L**<br>**Nomenclature**|**K3MA-L**<br>**Nomenclature**|**K3MA-L**<br>**Nomenclature**|**K3MA-L**<br>**Nomenclature**|
|---|---|---|---|
|**1**<br>Max<br>Min<br>**SV**<br>**MAX/MIN**<br>**LEVEL**<br>**MODE**<br>**SHIFT**<br>**UP**<br>2. Operation indicators<br>3. Level indicator<br>4. MAX/MIN key<br>5. Level key<br>6. Mode key<br>7. Shift key<br>8. Up key<br>1. Main indicator||||
|**Name**||**Functions**||
|1. Main indicator||Displays current values, parameters, and set values.||
|2. Opera-<br>tion indica-<br>tors|1|Lit when output 1 is ON.||
||SV|Lit when a set value is beingdisplayed or changed.||
||Max|Lit when the main indicator is showingthe MAX value.||
||Min|Lit when the main indicator is showingthe MIN value.||
|3. Level indicator||Displays the current level that the K3MA-L is in. (See below for details.)||
|4. MAX/MIN Key||Used to displaythe MAX and MIN values when a measurement value is beingdisplayed.||
|5. Level Key||Used to change the level.||
|6. Mode Key||Used to allow the main indicator to indicate parameters sequentially.||
|7. Shift Key||Used to enable a set value to be changed. When changinga set value, this keyis used to move alongthe digits.||
|8. Up Key||Used to change a set value. Used to set or clear a forced-zero function when a measurement value is beingdisplayed.||
|**Level indicator**<br>**Level**<br>p<br>Protect<br>Not lit<br>Operation<br>a<br>Adjustment<br>s<br>Initial setting<br>f<br>Advanced-function setting||||
|**Level indicator**|||**Level**|
|p|||Protect|
|Not lit|||Operation|
|a|||Adjustment|
|s|||Initial setting|
|f|||Advanced-function setting|



**7** 

**K3MA-L** 

**(Unit:mm)** 

## **Dimensions** 

**==> picture [381 x 171] intentionally omitted <==**

**----- Start of picture text -----**<br>
101.2  Finger protective  Main indicator  Panel cut-out<br>91  cover (provided)<br>character size 120 min.<br>14.2 mm<br>85<br>97<br>7.6 mm 75 min. 92 + 0 0.5<br>An 12  | [= 45+0.50<br>1.3<br>———=—Es 80 ry<br>96  Mounting Recommended Panel Thickness<br>1 to 8 mm.<br>— —T BE=FaI 44.8 Mount the product horizontally.<br>48<br>| al | G Ee<br>MAX/MIN  LEVEL  MODE  SHIFT  UP  The K3MA-L uses M3 terminals.<br>A terminal cover is provided.<br>E  D  C  B  A<br>**----- End of picture text -----**<br>


## **A lication Exam les pp p** 

**Monitoring the temperature of an industrial furnace** 

**Sending a temperature alarm for molding equipment** 

**Monitoring the bearing temperature for a generator motor** 

**==> picture [270 x 95] intentionally omitted <==**

**----- Start of picture text -----**<br>
PID control<br>Temperature<br>Controler<br>r K3MA-L<br>K3MA-L<br>Industrial furnace | Alarm output<br>Molding equipmentAlarm output<br>**----- End of picture text -----**<br>


**==> picture [130 x 36] intentionally omitted <==**

**----- Start of picture text -----**<br>
Generator motor<br>Alarm output<br>K3MA-L<br>**----- End of picture text -----**<br>


- Monitoring the temperature of an industrial furnace/sintering furnace. 

- Monitoring/alarm function for disinfecting equipment. 

- Monitoring (failsafe checking) abnormal temperatures in molding equipment. 

- Monitoring the liquid temperature for cleaning devices. 

- Monitoring temperature rises in electric power generating facilities. 

- Inspecting temperatures in machines and devices. 

**8** —_ 

**K3MA-L** 

## **Installation** 

**1.** Insert the K3MA-L into the panel cut-out hole. 

**2.** For a waterproof installation, insert the rubber gasket onto the body of the K3MA-L. 

**==> picture [177 x 124] intentionally omitted <==**

**3.** Fit the adaptor into the grooves on the left and right sides of the rear case, then push it until it contacts the panel to secure the K3MA-L. 

**==> picture [122 x 106] intentionally omitted <==**

## ■ **LCD Angle of View** 

The K3MA is designed to provide the best visibility at the angles shown in the following diagram. 

## ■ **Wiring Precautions** 

- Use crimp terminals. 

- Tighten the terminal screws to a torque of approximately 0.5 N ⋅ m. 

- To avoid the influence of noise, route signal lines and power lines separately. 

## ■ **Wiring** 

- Use the following M3 crimp terminals. 

**==> picture [107 x 52] intentionally omitted <==**

**----- Start of picture text -----**<br>
5.8 mm max.<br>5.8 mm max.<br>**----- End of picture text -----**<br>


## ■ **Unit Labels (Provided)** 

- The unit labels are not attached to the K3MA-L. Select the desired labels from the provided sheet. 

**==> picture [108 x 100] intentionally omitted <==**

**Note:** For scales and gauges, use the unit labels that are specified by the relevant laws or regulations. 

**==> picture [148 x 52] intentionally omitted <==**

**----- Start of picture text -----**<br>
10°<br>30°<br>**----- End of picture text -----**<br>


## ■ **Watertight Cover** 

## **Y92A-49N** 

**==> picture [89 x 65] intentionally omitted <==**

## ■ **Rubber Packing** 

## **K32-P1** 

**==> picture [68 x 77] intentionally omitted <==**

If the rubber packing is lost or damaged, it can be ordered using the following model number: K32-P1. 

(Depending on the operating environment, deterioration, contraction, or hardening of the rubber packing may occur and so, in order to ensure the level of waterproofing specified in NEMA4, periodic replacement is recommended.) 

**Note:** Rubber packing is provided with the Controller. 

**9** 

**K3MA-L** 

## **O eratin Procedures p g** 

## ■ **Operations in Run Mode** 

## **Checking the Maximum and Minimum Values** 

The maximum and minimum values can be displayed by pressing the MAX/MIN Key while the measurement is being displayed. 

**==> picture [282 x 34] intentionally omitted <==**

**----- Start of picture text -----**<br>
MAX/MIN Key MAX/MIN Key MAX/MIN Key<br>Measurement MAX value MIN value<br>value<br>**----- End of picture text -----**<br>


The maximum and minimum values can be reset by pressing the MAX/MIN Key for 1 s min. when the maximum or minimum value is displayed. 

## **Checking and Setting Comparative Set Values (for Models with the Comparative Output Function)** 

Each time the Mode Key is pressed when the measurement value, maximum value, or minimum value is displayed, the comparative values will be displayed in the following order: OUT1 value (or OUT1 upper-limit value, OUT1 lower-limit value). 

**==> picture [223 x 76] intentionally omitted <==**

**----- Start of picture text -----**<br>
OUT1<br>value<br>Measurement<br>value<br>MAX value<br>MIN value OUT1 upper- OUT1 lower-  Mode Key<br>limit value limit value<br>Mode Key Mode Key<br>**----- End of picture text -----**<br>


## ■ **Adjustment Level Operation** 

## **Setting Temperature Input Shift Values** 

## **Temperature Input Shift** 

A shift value can be set for a temperature input. 

**==> picture [173 x 121] intentionally omitted <==**

**----- Start of picture text -----**<br>
After shift<br>Before shift<br>Input shift value<br>Input<br>Temperature<br>**----- End of picture text -----**<br>


The value set for the temperature input shift is applied to the entire measurement range of the temperature sensor. 

**10** 

**K3MA-L** 

## ■ **Levels** 

“Level” refers to a grouping of parameters. The following table lists the operations that are possible in each of the levels, and the diagram tells how to move between levels. There are some parameters that are not displayed for certain models. 

|**Level name**|**Function**|**Measurement**|
|---|---|---|
|Protect|Settinglockouts.|Continue|
|Operation|Displayingcurrent values, and settingOUT 1 value.|Continue|
|Adjustment|Settingcommunications writingcontrol.|Continue|
|Initial setting|Making initial settings of input type, output operating action, and other<br>parameters.|Stopped|
|Advanced-function setting|Setting average processing, display color settings, and other ad-<br>vanced function parameters.|Stopped|



**==> picture [384 x 300] intentionally omitted <==**

**----- Start of picture text -----**<br>
Power ON<br>Operation level Adjustment level<br>+<br>Time set  Less than 1 s<br>by user<br>(See note.) Flashing stops if key<br>1 s min.  is released.<br>Protect level<br>1 s min.<br>+<br>1 s min.  - 123.4<br>Indicates change of level.<br>Continue to press the key for 2 s<br>min.<br>Initial setting level<br>Password "−0169"<br>1 s min.<br>Advanced-function<br>setting level<br>**----- End of picture text -----**<br>


**Note:** The move-to-protect-level time can be set in the advanced-function setting level. 

**11** 

**K3MA-L** 

## ■ **Parameters** 

**Note:** 1.   Some parameters are not displayed for certain models. 

2.   The K3MA-L will stop measurement if the level is changed to the initial setting level or the advanced-function setting level. 

3.   If the input range is changed, some parameters are set to default values. Therefore, set the input range first. 

4.   Settings displayed in reversed colors are defaults. 

**==> picture [522 x 306] intentionally omitted <==**

**----- Start of picture text -----**<br>
Power ON<br>         Press Level Key<br>for less than 1 s.<br>Adjustment level Operation level<br>         Press Level Key<br>for less than 1 s.<br>Current value<br>Temperature input shift MODE<br>For models with the<br>− 0 − comparative output function OUT1 value  −<br>MODE<br>Set one of these.<br>OUT1<br>upper-limit  −<br>value<br>MODE<br>OUT1 lower-limit  −<br>value<br>MODE<br>**----- End of picture text -----**<br>


**12** 

**K3MA-L** 

**==> picture [560 x 378] intentionally omitted <==**

**----- Start of picture text -----**<br>
Press Level  To change a setting, press the Shift Key         again, and then<br>make the change with the Up Key        .<br>Key         for<br>more than 3 s.<br>Press Level Key        for less than 1 s.<br>Initial setting level Advanced-function<br>setting level<br>Press Level<br>Key         for Enter<br>more than 1 s. password "−0169"<br>Input type − − Parameter initialization /<br>MODE<br>Temperature unit MODE<br>Temperature<br>unit −<br>MODE Average processing / / /<br>Models  OUT1 type Unit: times<br>with the compara- OUT1 type Upper Limit MODE OUT1 hysteresis<br>tive out- Lower Limit Models<br>put function MODE Upper/Lower Limits with the compar-ative out- OUT1 Hysteresis − −<br>Move to  put<br>advanced- function  − function MODE<br>setting level<br>MODE Display  Green (red)<br>color  Green<br>change<br>Red (green)<br>Password: −0169<br>MODE Red<br>Display<br>auto-return time − −<br>Unit: s<br>MODE<br>Move-to-<br>protect-level time − −<br>Unit: s<br>MODE<br>Settings displayed in reversed colors are initial settings.<br>**----- End of picture text -----**<br>


**13** 

**K3MA-L** 

**==> picture [162 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
Press             Level Key +           Mode Key for more than 1 s.<br>**----- End of picture text -----**<br>


**==> picture [358 x 134] intentionally omitted <==**

**----- Start of picture text -----**<br>
Operation Level Protect level<br>Press           Level Key +           Mode Key<br>for more than preset time.<br>Operation/adjustment   / /<br>lockouts<br>MODE<br>Setting level lockouts / /<br>MODE<br>Setting change lockout /<br>MODE<br>**----- End of picture text -----**<br>


## **Operation/Adjustment Lockouts** 

Restricts key operations for operation level and adjustment level. 

|**Parame-**<br>**ter**|**Setting**|**Operation level**|**Operation level**|**Moving to**<br>**adjustment**<br>**level**|
|---|---|---|---|---|
|||**Process value**<br>**display**|**Set value**<br>**display**||
|oapt|0|Allowed|Allowed|Allowed|
||1|Allowed|Allowed|Prohibited|
||2|Allowed|Prohibited|Prohibited|



- Initial setting is 0. 

- This cannot be displayed on models not equipped with the comparative output function. 

## **Setting Level Lockouts** 

## ■ **Initial Settings** 

**==> picture [223 x 67] intentionally omitted <==**

**----- Start of picture text -----**<br>
Power ON<br>Press the Level Key        for 3 s min. to move to the initial setting<br>level.<br>**----- End of picture text -----**<br>


Select the input type. If desired, shift to the adjustment level to set the temperature input shift value. 

Restricts shifting to initial setting level or advanced-function setting level. 

|**Parameter**|**Setting**|**Shift to initial**<br>**setting level**|**Shift to**<br>**advanced-**<br>**function**<br>**setting level**|
|---|---|---|---|
|icpt|0|Allowed|Allowed|
||1|Allowed|Prohibited|
||2|Prohibited|Prohibited|



## **Setting Change Lockout** 

Restricts setting changes by key operation. When this lockout is set, it is no longer possible to shift to a setting change mode. 

|**Parameter**|**Setting**|**Setting change by key**<br>**operation**|
|---|---|---|
|wtpt|off|Allowed|
||on|Prohibited|



**==> picture [223 x 46] intentionally omitted <==**

**----- Start of picture text -----**<br>
If required, shift to the advanced-function setting level to set the<br>number of measurements for averaging, hysteresis values,<br>auto-zero time, display color change, display auto-return time,<br>or move-to-protect-level time.<br>**----- End of picture text -----**<br>


Press the Level Key        for less than 1 s min. to return to the operation level. 

Set the OUT values. Measurement starts. 

However, all protect level parameters can still be changed. 

**14** 

**K3MA-L** 

## ■ **Setting Example** 

## **Initial Settings** 

The settings for the following example are shown here. 

## **Example: Monitoring the temperature of an industrial furnace** 

**==> picture [172 x 96] intentionally omitted <==**

**----- Start of picture text -----**<br>
E52-PR Thermocouple<br>Industrial furnace<br>1 MaxMin<br>SV<br>MAX/MIN LEVEL MODE SHIFT UP<br>K3MA-L-C 100-240VAC<br>**----- End of picture text -----**<br>


Here, the temperature inside the furnace is to be displayed in centigrade ( ° C). 

Temperature sensor: E52-PR Thermocouple, Measurement range: 0 to 1,400 ° C. 

**1.** Set the K3MA-L input type to the thermocouple R input range. Parameter: in-t (input type), Setting value: 16 

**2.** Select centigrade ( ° C) as the temperature unit. Parameter: d-u (temperature unit), Setting value: c 

If you are using a comparative output model, make the setting as desired. 

## ■ **Troubleshooting** 

When an error occurs, error details will be displayed on the main indicator. Confirm the error from the main indicator and take the appropriate countermeasures. 

|<br>countermeasures.||||
|---|---|---|---|
|**Level display**|**Main indicator**|**Error contents**|**Countermeasures**|
|Not lit|e111|RAM memory error|Repair is necessary.<br>Consult your OMRON sales repre-<br>sentative.|
|5|e111|EEPROM memory error|When this error is displayed, press<br>the Level Key for 3 seconds, and<br>the settings will be restored to the<br>factory settings.<br>If the error cannot be recovered, re-<br>pair is necessary.<br>Consult your OMRON sales repre-<br>sentative.|
|Not lit|Flashess.err|Input error|Confirm that the temperature sen-<br>sor is correctly connected, and that<br>there are no broken signal lines to<br>the temperature sensor.<br>Input value is out of the specified<br>range (control range). Set the value<br>within the range immediately.<br>If the condition does not return to<br>normal, repair is necessary.<br>Consult your OMRON sales repre-<br>sentative.|
|Not lit|Flashes9999|The measurement value after tem-<br>perature input correction exceeds<br>9999.|The temperature input correction<br>value may be inappropriate.<br>Use the adjustment level to review<br>the temperature input correction<br>value.|
|Not lit|Flashes-1999|The measurement value after tem-<br>perature input correction is lower<br>than−1999.|The temperature input correction<br>value may be inappropriate.<br>Use the adjustment level to review<br>the temperature input correction<br>value.|



ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. 

In the interest of product improvement, specifications are subject to change without notice. 

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. 

**15** 

## Terms and Conditions Agreement 

## Read and understand this catalog. 

Please read and understand this catalog before purchasing the products.  Please consult your OMRON representative if you have any questions or comments. 

## Warranties. 

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. 

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE 

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. 

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. 

See http://www.omron.com/global/ or contact your Omron representative for published information. 

## Limitation on Liability; Etc. 

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. 

## Suitability of Use. 

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. 

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 

## Programmable Products. 

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. 

## Performance Data. 

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. 

## Change in Specifications. 

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. 

## Errors and Omissions. 

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 

**In the interest of product improvement, specifications are subject to change without notice.** 

## **OMRON Corporation** 

## **Industrial Automation Company** 

2017.4 

**http://www.ia.omron.com/** 

(c)Copyright OMRON Corporation 2017 All Right Reserved.