JPS130PS15-M

**130 Watts** 

xppower.com 

## **JPS Series** 

- High Efficiency - up to 90% 

- Medical Approval (JPS130-M Versions) 

- 3”x 5”Footprint 

- 100 W Convection-cooled 

- 130 W Forced-cooled 

- Single & Multi Outputs 

- 3 Year Warranty 

## **S** ~~**pecification**~~ 

## **Input** 

- Input Voltage • 90-264 VAC (130-370 VDC) Input Frequency • 47-63 Hz Input Current • 2.0/1.0 A max at 115/230 VAC (JPS130) 2.6/1.3 A max at 115/230 VAC (JPS130-M) 

- Inrush Current • 30 A at 115 VAC, 60 A at 230 VAC, cold start at 25 °C 

- Power Factor • 0.9 typical Earth Leakage Current • 1.5 mA max at 264 VAC/60 Hz (JPS130) 260 µA max at 275 VAC/63 Hz (JPS130-M) 

- Input Protection • JPS130 internal T3.15 A/250 VAC fused line, JPS130-M fused line & neutral 

## **Output** 

- Output Voltage • See table Output Voltage Trim • ±10% on single output models, ±5% on multi output models, auxiliary outputs will track by the same percentage 

- Initial Set Accuracy • At 60% rated load ±1% single outputs, ±3% on V1 for multi outputs 

- Minimum Load • Single output: no minimum load required Multi-outputs: (see note 1) 

- Start Up Rise Time • <20 ms Hold Up Time • 16 ms typical at 115 VAC & rated load (JPS130) 20 ms typical at 115 VAC & rated load (JPS130-M) 

- Drift • <±0.2% after 20 mins warm up Line Regulation • ±0.5% Vmin to Vmax Load Regulation • ±1%, ±5% for auxiliary outputs, 20%-100% of rated load 

- Transient Response • 4% max deviation, recovery to within 1% in 500 μ s for a 25% load change 

- Ripple & Noise • ±1% max pk-pk (see note 4) Overvoltage Protection • 110-140% Vnom on V1 only, recycle input to reset 

- Overload Protection • 110-150%, auto recovery Short Circuit Protection • Trip & restart (hiccup mode), auto recovery Temperature • 0.05%/°C Coefficient Remote Sense • Single output models only, compensates for up to 0.5 V drop 

- Fan Output • 12 V, 450 mA multi-output models only 

## **General** 

|**General**||
|---|---|
|Efficiency|• Up to 90% nominal line, full load|
|Isolation|• 3000 VAC Input to Output (JPS130),|
||4000 VAC Input to Output (JPS130-M|
||2 x MOPP), 1500 VAC Input to Ground|
||(JPS130-M 1 x MOPP),|
||500 VAC Output to Ground|
|Switching Frequency|• 120 kHz, ±10% for both active PFC & PWM|
|Power Density|• 6.7 W/In3|
|MTBF|• 200 kHrs to MIL-HDBK-217F at 50 °C, GB|
|**Environmental**||
|Operating Temperature|• 0 °C to +70 °C, (see derating curves)|
|Cooling|• JPS130PS03 83 W convection-cooling,<br>100 W, with 18 CFM airflow.|
||All others, 100 W with convection|
||cooling,130 W with 18 CFM airflow|
|Operating Humidity<br>Storage Temperature<br>Operating Altitude|• 5-95% RH, non-condensing<br>• -40 °C to +85 °C (JPS130)<br>-20 °C to +85 °C (JPS130-M)<br>• 3000 m|



## **Environmental** 

## **EMC & Safety** 

|**EMC & Safetyy**||
|---|---|
|Emissions<br>Harmonic Currents<br>Voltage Flicker|• EN55032, Class B conducted<br>FCC 20780, level B conducted<br>EN60601-1-2, (JPS130-M)<br>• EN61000-3-2 Class A<br>• EN61000-3-3|
|ESD Immunity|• EN61000-4-2, level 3 contact, level 3 air,<br>Perf Criteria A|
|Radiated Immunity|• EN61000-4-3, 10 V/m Perf Criteria A|
|EFT/Burst|• EN61000-4-4, level 3 Perf Criteria A|
|Surge|• EN61000-4-5, Installation Class 3|
||Perf Criteria A|
|Conducted Immunity|• EN61000-4-6, level 2, Perf Criteria A|
|Dips & Interruptions|• EN61000-4-11, 30% 10 ms, 60% 100 ms,|
||95% 5000 ms Perf Criteria A, B, B|
|Safety Approvals|• JPS130:<br>EN60950-1, UL60950-1,|
||CSA C22.2 No. 60950-1,|
||JPS130-M: UL60601-1, EN60601-1,|
||CSA C22.2 No. 601.1|
||CE & UKCA meets all applicable directives|
||& legislation|



**JPS130** 

## ~~**Models and Ratings**~~ 

|Output<br>Power(3)|Output<br>Voltage|Output Current|Output Current|Ripple & Noise<br>Pk-Pk(4)<br>~~a~~|Standard Model<br>Number|Medical Model<br>Number|
|---|---|---|---|---|---|---|
|||Convection-cooled|18 CFM||||
|100 W<br>~~a~~|3.3 V<br>~~a~~<br>~~a~~|25.0 A<br>~~a~~<br>|30.0 A<br>~~a~~<br>|50 mV<br>~~a~~<br>~~a~~|JPS130PS03<br>~~a~~<br>~~sd~~|~~a~~<br>~~sd~~<br>~~———CC*”~~|
|130 W<br>~~a~~|5.0 V<br>12.0 V<br>15.0 V<br>24.0 V<br>28.0 V<br>48.0 V<br>~~a~~<br>~~LOSS~~<br>~~a ~~<br>~~a ~~<br>~~LOSS~~<br>~~a~~<br>~~a~~|20.0 A<br>~~a~~<br>~~LOSS~~<br>~~Oa~~<br>|26.0 A<br>~~a~~<br>~~LOSS~~<br>~~Oa~~<br>|50 mV<br>~~a~~<br>~~a~~<br>~~LOSS~~|JPS130PS05<br>~~a~~<br>~~LOSS~~<br>~~sd~~|JPS130PS05-M<br>~~a~~<br>~~LOSS~~<br>~~sd~~<br>~~———CC*”~~|
|||9.0 A<br>~~Oa~~<br>|10.8 A<br>~~Oa~~<br>|120 mV|JPS130PS12<br>~~sd~~|JPS130PS12-M<br>~~sd~~<br>~~———CC*”~~|
|||7.0 A<br> ~~Oa~~<br> ~~a~~<br>~~LOSS~~|8.7 A<br>~~Oa~~<br>~~a~~<br>~~LOSS~~|120 mV<br>~~LOSS~~|JPS130PS15<br>~~sd~~<br>~~SSeS~~|JPS130PS15-M<br>~~sd~~<br>~~———CC*”~~<br>~~SSeS~~|
|||4.5 A<br>~~LOSS~~|5.4 A<br>~~LOSS~~|200 mV<br>~~LOSS~~|JPS130PS24<br>~~SSeS~~|JPS130PS24-M<br>~~SSeS~~|
|||3.8 A<br>~~LOSS~~<br>~~a~~<br>~~a~~|4.6 A<br>~~LOSS~~<br>~~a~~<br>~~a~~|200 mV<br>~~LOSS~~|~~SSeS~~|JPS130PS28-M<br>~~SSeS~~|
|||2.1 A<br>~~a~~<br>~~a~~|2.7 A<br>~~a~~<br>~~a~~|200 mV|JPS130PS48|JPS130PS48-M|
|130 W|+ 5.0 V(1)<br>+12.0 V(2)<br>-12.0 V(2)<br>~~a~~<br>~~a ~~<br>~~TOTO~~|11.5 A|15.0 A|50 mV|JPS130PT31<br>~~SCS~~||
|||3.0 A<br> ~~Ca~~<br>~~TOTO~~|5.0 A<br>~~Ca~~<br>~~TCOCCOCTCCdT~~|100 mV<br>~~Ca~~<br>~~TCOCCOCTCCdT~~<br>~~SCS~~|||
|||0.5 A<br>~~TOTO~~|0.5 A<br>~~TCOCCOCTCCdT~~|100 mV<br>~~TCOCCOCTCCdT~~<br>~~SCS~~|||
|130 W|+ 3.3 V(1)<br>+5.0 V(2)<br>+12.0 V(2)<br>~~TOTO~~<br>~~a~~<br>~~a a~~<br>~~a~~|10.0 A<br>~~TOTO ~~|15.0 A<br> ~~TCOCCOCTCCdT~~|50 mV<br>~~TCOCCOCTCCdT~~<br>~~SCS~~|JPS130PT30<br>~~SCS~~||
|||8.0 A<br>~~a~~<br>~~Ca~~|15.0 A<br>~~a~~|50 mV<br>~~a~~|||
|||0.5 A<br>~~a~~<br>~~Ca~~|0.5 A<br>~~a~~|100 mV<br>~~a~~|||
|130 W|+ 5.0 V(1)<br>+12.0 V(2)<br>-12.0 V(2)<br>~~a ~~<br>~~a~~<br>~~[DO~~<br>~~a~~|10.0 A<br> ~~Ca~~|15.0 A|50 mV||JPS130PT31-M|
|||3.0 A<br>~~[DO~~|4.1 A<br>~~[DO~~|120 mV<br>~~[DO~~|||
|||0.8 A|1.1 A|120 mV|||
|130 W|+5.0 V(1)<br>+15.0 V(2)<br>-15.0 V(2)<br>~~a ~~<br>~~a ~~<br>~~[OOO~~<br>~~a~~|10.0 A<br>~~a~~|15.0 A|50 mV|~~——S~~|JPS130PT32-M|
|||2.5 A<br> ~~a~~<br> ~~Ca~~|4.1 A<br>~~Ca~~<br>~~OOOO~~<br>~~|.~~|150 mV<br>~~Ca~~<br>~~|.——S~~|||
|||0.8 A<br>~~[OOO~~|1.1 A<br>~~[OOO~~<br>~~OOOO~~<br>~~|.~~|150 mV<br>~~[OOO~~<br>~~|.——S~~|||
|130 W|+5.0 V(1)<br>+24.0 V(2)<br>+12.0 V(2)<br>~~a~~<br>~~a~~<br>~~TOTO~~|2.5 A|4.0 A<br>~~OOOO~~<br>~~|.~~|50 mV<br>~~|.——S~~|~~——S~~<br>~~TCS~~|JPS130PT34-M|
|||2.8 A<br>~~TOTO~~|4.0 A<br>~~OCCT~~|240 mV<br>~~OCCTTCS~~|||
|||0.7 A<br>~~TOTO~~|1.0 A<br>~~OCCT~~|120 mV<br>~~OCCTTCS~~|||



## ~~**Notes**~~ 

_1. 20% minimum load required on V1 to maintain stated regulation for auxiliary rails._ 

_2. Load regulation of auxiliary rails is defined over the range of 20%-100% of rated load._ 

_3. Maximum power with 18 CFM of forced air._ 

_4. Ripple and noise measured over 15 MHz bandwidth with a 47 μ F electrolytic capacitor and 0.47 μ F ceramic capacitor._ 

_5. Covers available, order part number ‘JPS130-M COVER’ or add suffix ‘-C’ to receive the unit with cover fitted. Overall dimensions 89.5 x 143.0 x 40.0 mm. For industrial units order part number ‘JPS130 COVER’ or add suffix ‘-C’ to receive the unit with cover fitted. Overall dimensions 90.6 x 142.9 x 39.8 mm. Fixing screws M3, maximum penetration depth 3mm from cover outer surface._ 

_6. Connector kits and cable harnesses available. Consult sales for options._ 

## ~~**Mechanical Details**~~ 

**==> picture [238 x 113] intentionally omitted <==**

**----- Start of picture text -----**<br>
JPS130-M PIN CONNECTIONS<br>TB2 PS05 PS 12 - 48 PT31 PT32 PT34<br>1 Return Return -12 V -15 V +12 V<br>a a<br>2 Return Return +12 V +15 V +24 V<br>a 3 Return a Return Return Return Return<br>a a<br>4 Return +V Return Return Return<br>5 +V +V Return Return Return<br>a 6 a +V a +V a Return Return Return<br>a 788 +V+V+V Ca +5 V+5 V+5 V +5 V+5 V+5 V +5 V+5 V+5 V<br>9 +5 V +5 V +5 V<br>a Type *5273-08A Ca *5273-06A *5273-09A<br>_ Ht<br>**----- End of picture text -----**<br>


**==> picture [559 x 234] intentionally omitted <==**

**----- Start of picture text -----**<br>
— 0.16 (4.0) Dia Mounting Hole (4 Places) 0.22 (5.7) [0.2 (5.0) -M] i<br>— TB2 PS05 PS 12 - 48 PT31 PT32 PT34<br>1 Return Return -12 V -15 V +12 V<br>° O OTF a a<br>2 Return Return +12 V +15 V +24 V<br>TB2 TB2 a 3 Return a Return Return Return Return<br>“Vj L = J oO 1 a 4 Return a +V Return Return Return<br>N TB1 5 +V +V Return Return Return<br>ef fe a 6 a +V a +V a Return Return Return<br>1<br>Own lel) -M version a 788 +V+V+V Ca +5 V+5 V+5 V +5 V+5 V+5 V +5 V+5 V+5 V<br>Voltage Trim 9 +5 V +5 V +5 V<br>SC TB3 1 | a Type *5273-08A Ca *5273-06A *5273-09A<br>CIENNNS oP_ O _ Ht<br>4.55 (115.6)  [4.60 (117.0) -M]<br>JPS130 PIN CONNECTIONS<br>5.00 (127.0)<br>To Chassis Grounding x 2 a TB21 PS05+V a PS03,+V 12 - 48 PT31+5 V +3.3 VPT30<br>i 2 +V +V +5 V +3.3 V<br>3 a +V a +V +5 V Return<br>0.10(2.5) max a 4  a +V a Return Return Return<br>1+ 5 Return Return Return Return<br>6 Return Return Return Return<br>7 a Return a Return Return<br>All dimensions are in inches (mm).Tolerance: 0.02 (0.4) max.  Pin1TB3 PIN CONNECTIONS- SenseSingle  Multi 0 V aa 89 aa Return aa a +12 V-12 V +5 V+5 V<br>Weight: 0.5 lbs (240 g) approx. 2 + Sense +12 V Fan a 10 +12 V<br>a Type a *5273-08A a *5273-06A *5273-09A *5273-10A<br>3.00 (76.2) 2.55 (64.8)<br>[2.60 (66.2) -M]<br>(1)<br>1.18 (30.0) max<br>**----- End of picture text -----**<br>


## ~~**Notes**~~ 

* Note: MOLEX connector type 

1. Single output industrial model shown, add extra 0.08” (2.0 mm) to overall height for multi-output models. Dimensions followed by ‘-M’ apply for medical units (note output connector orientation). 

## ~~**Derating Curves**~~ 

2. AC input connector (TB1): Molex 5277-02A or equivalent. Mates with 5196-N housings/5194/5225 crimps. 

**==> picture [533 x 88] intentionally omitted <==**

**----- Start of picture text -----**<br>
3. DC output connector (TB2): Molex 5273 or equivalent, mates with 5195-N 5196-N housings/5194/5225 crimps.  100130 a+f + Fs A O A JPS130 and ‘-M’ with 18 CFM fan(except JPS130PS03).<br>housing/5194/5225 crimps and 5239-N housing/5167/5168/2478/2578 crimps. Except JPS130PS03 which has a 6-position terminal screw  80 po NSIS D C B O B JPS130PS12, PS15, PS24 and PS48and ‘-M’ with convection cooling.<br>block: Dinkle part number EHK508V Series accepts 24-12 AWG wire.  60 SSE JPS130PS03 with 18 CFM fan.<br>Terminal screw tightening torque 4 lbs-in (0.45 Nm) maximum.   40 C JPS130PS05, PT30, PT31, PT32 and<br>4. TB3: Molex 5045-02A or equivalent. Mates with KK 51191 housings/50802 crimps and KK 5051 housings/2759/5159 crimps. Single  200 aNoee ee ee ee e e D PT34 and ‘-M’ with convection cooling.JPS130PS03 with convection cooling.<br>output units - TB3 is remote sense. Multi-output units - TB3 is 12 V,   -10 0 10 20 30 40 50 60 70<br>450 mA fan output.  Ambient Temp (˚C)<br>Load (W)<br>**----- End of picture text -----**<br>


06 July 2022