HO 10-P

**Current Transducer HO-P series** 

## _I_ **= 6, 10, 25 A PN** 

## **Ref: HO 6-P, HO 10-P, HO 25-P** 

**For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.** 

## **Features** 

- ●Hall effect measuring principle 

- ●Galvanic separation between primary and secondary circuit 

- ●Insulated test voltage 4300 V 

- ●Low power consumption 

- ●Single power supply +5 V 

- ●Fixed offset & sensitivity 

- ●Over-current detect 2.63 × _I_ PN (peak value) 

- ●Memory check. 

## **Advantages** 

- ●Small size and space saving 

- ●Only one design for wide primary current range 

- ●High immunity to external interference 

- ●8 mm creepage /clearance 

- ●High insulation capability 

- ●Fast response. 

## **Applications** 

- ●AC variable speed drives 

- ●Static converters for DC motor drives 

- ●Battery supplied applications 

- ●Uninterruptible Power Supplies (UPS) 

- ●Switched Mode Power Supplies (SMPS) 

- ●Power supplies for welding applications 

- ●The solar inverter on DC side of the inverter (MPPT) 

- ●Combiner box. 

## **Standards** 

- ●EN 50178: 1997 

- ●IEC 61010-1: 2010 

- ●IEC 61326-1: 2012 

- ●UL 508: 2010. 

## **Application Domain** 

- ●Industrial. 

N°74.54.09.000.0, N°74.54.13.000.0, N°74.54.19.000.0 21October2014/Version 3 

Page 1/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

www.lem.com 

**HO-P series** 

## **Absolute maximum ratings** 

**==> picture [512 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Value<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Value**|
|---|---|---|---|
|||||
|Supply voltage (not operating)|_U_C|V|6.5|
|Primary conductor temperature|_T_B|°C|125|
|ESD rating, Human Body Model (HBM)|_U_ESD|kV|2|



Stresses above these ratings may cause permanent damage. Exposure to absolute maximum ratings for extended periods may degrade reliability. 

## **UL 508: Ratings and assumptions of certification** 

File # E189713 Volume: 2 Section: 5 

## **Standards** 

- CSA C22.2 NO. 14-10 INDUSTRIAL CONTROL EQUIPMENT - Edition 11 - Revision Date 2011/08/01 

- UL  508 STANDARD FOR INDUSTRIAL CONTROL EQUIPMENT - Edition 17 - Revision Date 2010/04/15 

## **Ratings** 

**==> picture [512 x 20] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Value<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Value**|
|---|---|---|---|
|||||
|Primary involved potential||V AC/DC|600|
|Max surrounding air temperature|_T_A|°C|105|
|Primary current|_I_P|A|According to series primary<br>currents|
|Secondary supply voltage|_U_C|V DC|5|
|Output voltage|_V_out|V|0 to 5|



## **Conditions of acceptability** 

When installed in the end-use equipment, consideration shall be given to the following: 

- _1 - These devices have been evaluated for overvoltage category III and for use in pollution degree 2 environment._ 

- _2 -  A suitable enclosure shall be provided in the end-use application._ 

- _3 - The terminals have not been evaluated for field wiring._ 

- _4 - These devices have been evaluated for use in 105°C maximum surrounding air temperature._ 

- _5 -  The secondary (Sensing) circuit is intended to be supplied by a Isolated Secondary Circuit - Limited voltage circuit defined by UL 508 paragraph 32.5. The maximum open circuit voltage potential available to the circuit and overcurrent protection shall be evaluated in the end use application._ 

- _6 -  These devices are intended to be mounted on a printed wiring board of end-use equipment. The suitability of the connections (including spacings) shall be determined in the end-use application._ 

- _7 - Any surface of polymeric housing have not been evaluated as insulating barrier._ 

- _8 - Low voltage circuits are intended to be powered by a circuit derived from an isolating source (such as a transformer, optical isolator, limiting impedance or electro-mechanical relay) and having no direct connection back to the primary circuit (other than through the grounding means)._ 

## **Marking** 

Only those products bearing the UL or UR Mark should be considered to be Listed or Recognized and covered under UL's Follow-Up Service. Always look for the Mark on the product. 

Page 2/12 www.lem.com 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

## **HO-P series** 

## **Insulation coordination** 

**==> picture [512 x 21] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Value Comment<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Value**|**Comment**|
|---|---|---|---|---|
||||||
|RMS voltage for AC isolation test 50/60 Hz/1 min1)|_U_d|kV|4.3||
|Impulse withstand voltage 1.2/50 µs|_ÛW_|kV|8||
|Partial discharge extinction voltage @ 10 pC (rms)|_U_e|V|1650||
|Clearance (pri. - sec.)|_d_CI|mm|8|Shortest distance through air|
|Creepage distance (pri. - sec.)|_d_Cp|mm|8|Shortest path along device<br>body|
|Case material|||V0 according<br>to UL 94||
|Comparative tracking index|_CTI_||600||
|Application example|-|-|600 V<br>CAT III PD2|Reinforced insulation, non<br>uniform feld according to<br>EN 50178|
|Application example|-|-|300 V<br>CAT III PD2|Reinforced insulation, non<br>uniform feld according to<br>IEC 61010|
|Application example|-|-|1000 V<br>CAT III PD2|Simple insulation, non uniform<br>feld according to<br>EN 50178, IEC 61010|



## **Environmental and mechanical characteristics** 

**==> picture [512 x 20] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Min Typ Max Comment<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Min**|**Typ**|**Max**|**Comment**|
|---|---|---|---|---|---|---|
||||||||
|Ambient operating temperature|_T_A|°C|-40||105||
|Ambient storage temperature|_T_S|°C|-40||105||
|Surrounding temperature according to UL 508||°C|||105||
|Mass|_m_|g||10|||



Note: 1) Voltage of Retention pins has to be consider. If it is same as primary electrical potential, insulation is no issue. If it is same as secondary electrical potental, insulation of primary bus bar has to be considered. 

Page 3/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

## **HO-P series** 

## **Electrical data** _I_ PN **= 6 A** 

At _T_ A = 25 °C, _U_ C = +5 V, _N_ P = 1 turn, _R_ L = 10 KΩ unless otherwise noted (see Min, Max, typ. definition paragraph in page 7). 

**==> picture [512 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Min Typ Max Comment<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Min**|**Typ**|**Max**|**Comment**|
|---|---|---|---|---|---|---|
||||||||
|Primary nominal rms current|_I_**PN**|A||6|||
|Primary current, measuring range|_I_PM|A|-20||20||
|Supply voltage|_U_C|V|4.5|5|5.5||
|Current consumption|_I_C|mA||19|25||
|Reference voltage|_V_ref|V|2.475|2.5|2.525|Internal reference|
|External reference voltage|_V_ref|V|0.5||2.65||
|Output voltage range @_I_PM|_V_OUT-_V_ref|V|-2||2||
|Output voltage @_I_P= 0 A|_V_OUT|V||_V_ref+_V_OE|||
|Electrical offset voltage|_V_OE|mV|-10||10||
|Temperature coeffcient of_V_REF|_TCV_ref|ppm/K|||±160|-20 °C .. 85 °C<br>Internal reference|
||||||±190|-40 °C .. 105 °C<br>Internal reference|
|Temperature coeffcient of_V_OE|_TCV_OE|mV/K|||±0.14|-20 °C .. 85 °C|
|||||||-40 °C .. 105 °C|
|Theoretical sensitivity|_G_th|mV/A||100||600 mV/_I_PN@_U_C= 5 V|
|Sensitivity error|_ε_G|%|||±0.85|Factory adjustement|
|Temperature coeffcient of_G_|_TCG_|ppm/K|||±250||
|Linearity error 0 .._I_PN|_ε_L|% of_I_PN|||±0.5|@_U_C= 5 V|
|Linearity error 0 .._I_PM|_ε_L|% of_I_PM|||±0.8|@_U_C= 5 V|
|Gain error with respect to_U_C±10 %||%/%|||±0.05|Gain error per_U_Cdrift|
|Magnetic offset voltage<br>@_I_P= 0 after 2.5× _I_PN|_V_OM|mV|||±5||
|Reaction time @ 10 % of_I_PN|_t_ra|µs|||2|d_i_/d_t_=_I_PN/µs|
|Response time @ 90 % of_I_PN|_t_r|µs|||3.5|d_i_/d_t_=_I_PN/µs|
|Frequency bandwidth (-3 dB)|_BW_|kHz||250|||
|Output voltage noise (spectral density)<br>(DC .. 100 kHz)|_e_no|µVrms/√Hz|||32.9|@_U_C= 5 V|
|Output voltage noise<br>(DC .. 20 MHz)|_V_no|mVpp||80|||
|Over-current detect||V|2.6× _I_PN|2.9× _I_PN|3.2× _I_PN|peak value|
|Accuracy @_I_PN|_X_|% of_I_PN|||±1.35|_ε_G+ _ε_L|
|Accuracy @_I_PN@_T_A= +85°C|_X_|% of_I_PN|||±4.25|See formula note1)|
|Accuracy @_I_PN@_T_A= +105°C|_X_|% of_I_PN|||±5.22|See formula note1)|



Note: 1) Accuracy @ _I_ P and _X_ TA = ± [ _X_ + ( _TCG_ /10000) · ( _T_ A - 25) + _TCV_ OE · 100 · ( _T_ A -25) / ( _G_ th · _I_ P)]. 

Page 4/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

## **HO-P series** 

## **Electrical data** _I_ PN **= 10 A** 

At _T_ A = 25 °C, _U_ C = +5 V, _N_ P = 1 turn, _R_ L = 10 KΩ unless otherwise noted (see Min, Max, typ. definition paragraph in page 7). 

**==> picture [512 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Min Typ Max Comment<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Min**|**Typ**|**Max**|**Comment**|
|---|---|---|---|---|---|---|
||||||||
|Primary nominal rms current|_I_PN|A||10|||
|Primary current, measuring range|_I_PM|A|-25||25||
|Supply voltage|_U_C|V|4.5|5|5.5||
|Current consumption|_I_C|mA||19|25||
|Reference voltage|_V_ref|V|2.475|2.5|2.525|Internal reference|
|External reference voltage|_V_ref|V|0.5||2.65||
|Output voltage range @_I_PM|_V_OUT-_V_ref|V|-2||2||
|Output voltage @_I_P= 0 A|_V_OUT|V||_V_ref+_V_OE|||
|Electrical offset voltage|_V_OE|mV|-10||10||
|Temperature coeffcient of_V_ref|_TCV_ref|ppm/K|||±160|-20 °C .. 85 °C<br>Internal reference|
||||||±190|-40 °C .. 105 °C<br>Internal reference|
|Temperature coeffcient of_V_OE|_TCV_OE|mV/K|||±0.12||
|Theoretical sensitivity|_G_th|mV/A||80||800 mV/_I_PN, @_U_C= 5 V|
|Sensitivity error|_ε_G|%|||±0.85|Factory adjustement|
|Temperature coeffcient of_G_|_TCG_|ppm/K|||±250||
|Linearity error 0 .._I_PN|_ε_L|% of_I_PN|||±0.5|@_U_C= 5 V|
|Linearity error 0 .._I_PM|_ε_L|% of_I_PM|||±0.8|@_U_C= 5 V|
|Gain error with respect to_U_C±10 %||%/%|||±0.05|Gain error per_U_Cdrift|
|Magnetic offset voltage<br>@_I_P= 0 after 2.5× _I_PN|_V_OM|mV|||±6||
|Reaction time @ 10 % of_I_PN|_t_ra|µs|||2|d_i_/d_t_=_I_PN/µs|
|Response time @ 90 % of_I_PN|_t_r|µs|||3.5|d_i_/d_t_=_I_PN/µs|
|Frequency bandwidth (-3 dB)|_BW_|kHz||250|||
|Output voltage noise (spectral density)<br>(DC .. 100 MHz)|_e_no|µVrms/√Hz|||17.5||
|Output voltage noise<br>(DC .. 20 MHz)|_V_no|mVpp||50|||
|Over-current detect||V|2.6× _I_PN|2.9× _I_PN|3.2× _I_PN|peak value|
|Accuracy @_I_PN|_X_|% of_I_PN|||±1.35|_ε_G+ _ε_L|
|Accuracy @_I_PN@_T_A= +85 °C|_X_|% of_I_PN|||±3.75|See formula note1)|
|Accuracy @_I_PN@_T_A= +105 °C|_X_|% of_I_PN|||±4.55|See formula note1)|



Note: 1) Accuracy @ _I_ P and _X_ TA = ± [ _X_ + ( _TCG_ /10000) · ( _T_ A - 25) + _TCV_ OE · 100 · ( _T_ A -25) / ( _G_ th · _I_ P)]. 

Page 5/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

## **HO-P series** 

## **Electrical data** _I_ PN **= 25 A** 

At _T_ A = 25 °C, _U_ C = +5 V, _N_ P = 1 turn, _R_ L = 10 KΩ unless otherwise noted (see Min, Max, typ. definition paragraph in page 7). 

**==> picture [512 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
Parameter Symbol Unit Min Typ Max Comment<br>**----- End of picture text -----**<br>


|**Parameter**|**Symbol**|**Unit**|**Min**|**Typ**|**Max**|**Comment**|
|---|---|---|---|---|---|---|
||||||||
|Primary nominal rms current|_I_PN|A||25|||
|Primary current, measuring range|_I_PM|A|-62.5||62.5||
|Supply voltage|_U_C|V|4.5|5|5.5||
|Current consumption|_I_C|mA||19|25||
|Reference voltage|_V_ref|V|2.475|2.5|2.525|Internal reference|
|External reference voltage|_V_ref|V|0.5||2.65||
|Output voltage range @_I_PM|_V_OUT-_V_ref|V|-2||2||
|Output voltage @_I_P= 0 A|_V_OUT|V||_V_ref+_V_OE|||
|Electrical offset voltage|_V_OE|mV|-10||10||
|Temperature coeffcient of_V_ref|_TCV_ref|ppm/K|||±160|-20 °C .. 85 °C<br>Internal reference|
||||||±190|-40 °C .. 105 °C<br>Internal reference|
|Temperature coeffcient of_V_OE|_TCV_OE|mV/K|||±0.075||
|Theoretical sensitivity|_G_th|mV/A||32||800 mV/_I_PN@_U_C= 5 V|
|Sensitivity error|_ε_G|%|||±0.85|Factory adjustement|
|Temperature coeffcient of_G_|_TCG_|ppm/K|||±250||
|Linearity error 0 .._I_PN|_ε_L|% of_I_PN|||±0.5|@_U_C= 5 V|
|Linearity error 0 .._I_PM|_ε_L|% of_I_PM|||±0.8|@_U_C= 5 V|
|Gain error with respect to_U_C±10 %||%/%|||±0.05|Gain error per_U_Cdrift|
|Magnetic offset voltage<br>@_I_P= 0 after 2.5× _I_PN|_V_OM|mV|||±7||
|Reaction time @ 10 % of_I_PN|_t_ra|µs|||2|d_i_/d_t_=_I_PN/µs|
|Response time @ 90 % of_I_PN|_t_r|µs|||3.5|d_i_/dt =_I_PN/µs|
|Frequency bandwidth (-3 dB)|_BW_|kHz||250|||
|Output voltage noise (spectral density)<br>(DC .. 100 MHz)|_e_no|µVrms/√Hz|||10.5||
|Output voltage noise<br>(DC .. 20 MHz)|_V_no|mVpp||30|||
|Over-current detect||V|2.6× _I_PN|2.9× _I_PN|3.2× _I_PN|peak value|
|Accuracy @_I_PN|_X_|% of_I_PN|||±1.35|_ε_G+ _ε_L|
|Accuracy @_I_PN@_T_A= +85 °C|_X_|% of_I_PN|||±3.42|See formula note1)|
|Accuracy @_I_PN@_T_A= +105 °C|_X_|% of_I_PN|||±4.1|See formula note1)|



Note: 1) Accuracy @ _I_ P and _X_ TA = ±  [ _X_ + ( _TCG_ /10000) · ( _T_ A - 25) + _TCV_ OE · 100 · ( _T_ A -25) / ( _G_ th · _I_ P)]. 

Page 6/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

**HO-P series** 

## **Definition of typical, minimum and maximum values** 

Minimum and maximum values for specified limiting and safety conditions have to be understood as such as well as values shown in “typical” graphs. On the other hand, measured values are part of a statistical distribution that can be specified by an interval with upper and lower limits and a probability for measured values to lie within this interval. 

Unless otherwise stated (e.g. “100 % tested”), the LEM definition for such intervals designated with “min” and “max” is that the probability for values of samples to lie in this interval is 99.73 %. For a normal (Gaussian) distribution, this corresponds to an interval between -3 sigma and +3 sigma. If “typical” values are not obviously mean or average values, those values are defined to delimit intervals with a probability of 68.27 %, corresponding to an interval between -sigma and +sigma for a normal distribution. 

Typical, maximal and minimal values are determined during the initial characterization of a product. 

Page 7/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

**HO-P series** 

## **Maximum continuous DC primary current** 

**==> picture [510 x 207] intentionally omitted <==**

**----- Start of picture text -----**<br>
50 62.5<br>40 50<br>30 37.5<br>20 25<br>10 12.5<br>HO 615A HO  1015A<br>0 0<br>0 25 50 75 100 125 0 25 50 75 100 125<br>T A( ℃ ) T A( ℃ )<br> (A)<br>P<br>I  (A)<br>P<br>I<br>**----- End of picture text -----**<br>


**==> picture [207 x 204] intentionally omitted <==**

**----- Start of picture text -----**<br>
100<br>75<br>50<br>25<br>HO 25<br>0<br>0 25 50 75 100 125<br>T A( ℃ )<br> (A)<br>P<br>I<br>**----- End of picture text -----**<br>


_Figure 1: IP vs TA for HO series_ 

Important notice:  whatever the usage and/or application, the primary conductor temperature shall not go above the maximum rating of 125 °C as stated in page 2 of this datasheet. 

Page 8/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

**HO-P series** 

## **Measuring range with external reference voltage** 

**==> picture [457 x 459] intentionally omitted <==**

**----- Start of picture text -----**<br>
50<br>40 Upper limit:   IP = -10  ×  Vref +45 (Vref   = 0.5 .. 2.65 V)<br>30 Lower limit:   IP = -10  ×  Vref +5 (Vref   = 0.5 .. 2.65 V)<br>20<br>10<br>0<br>-10<br>-20 HO 6<br>-30<br>0.5 1 1.5 2 2.5<br>V ref (V)<br>60 Upper limit:   IP = -12.5  ×  Vref +56.25 (Vref   = 0.5 .. 2.65 V)<br>50<br>40 Lower limit:   IP = -12.5  ×  Vref +6.25 (Vref   = 0.5 .. 2.65 V)<br>30<br>20<br>10<br>0<br>-10<br>-20<br>-30 HO 10<br>-40<br>0.5 1 1.5 2 2.5<br>V ref  (V)<br>120 Upper limit:<br>90 TA = 105 °C  IP = 75 (Vref  = 0.5 ..2.1 V)<br>60 IP = 31.25  ×  Vref +140.63 (Vref   = 2.1 .. 2.65 V)<br>25 ℃<br>300 60 85 ℃ ℃ TA = 85 °C  IIPP = 80 (V = 31.25 ref  ×  = 0.5 ..1.94 V)  Vref +140.63 (Vref   = 1.94 .. 2.65 V)<br>-30 105 ℃ TA = 60 °C  IP = 90 (Vref  = 0.5 ..1.62 V)<br>IP = 31.25  ×  Vref +140.63 (Vref   = 1.62 .. 2.65 V)<br>-60<br>HO 25<br>-90 TA = 25 °C  IP = 95 (Vref  = 0.5 ..1.46 V)<br>0.5 1 1.5 2 2.5 IP = 31.25  ×  Vref +140.63 (Vref   = 1.46 .. 2.65 V)<br>V ref  (V) Lower limit:  IP = -31.25  ×  Vref +15.63 (Vref   = 0.5 .. 2.65 V)<br>I  (A)P<br>I  (A)P<br>Ip (A)<br>**----- End of picture text -----**<br>


_Example with Vref  = 0.5 V:_ 

- ●The 6 A version has a measuring range from 0 A to 40 A 

- ●The 10 A version has a measuring range from 0 A to 50 A 

- ●The 25 A version has a measuring range from 0 A to 75 A at _TA = 105 °C Example with Vref  = 1.5 V:_ 

- ●The 6 A version has a measuring range from -10 A to 30 A 

- ●The 10 A version has a measuring range from -18.7 A to + 56.3 A 

- ●The 25 A version has a measuring range from -31.2 A to + 80 A at _TA = 85 °C_ 

Page 9/12 

21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

www.lem.com 

## **HO-P series** 

## **PCB Footprint** 

## **Assembly on PCB** 

- Recommended PCB hole diameter 

   - 1.5 mm for retention pin 

   - 0.9 mm for secondary pin 

- Maximum PCB thickness 

- Wave soldering profile No clean process only 

- 2.4 mm 

- maximum 260 °C, 10 s 

## **Safety** 

This transducer must be used in limited-energy secondary circuits according to IEC 61010-1. 

This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer’s operating instructions. 

## Caution, risk of electrical shock. 

When operating the transducer, certain parts of the module can carry hazardous voltage (e.g. primary bus bar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. 

This transducer is a build-in device, whose conducting parts must be inaccessible after installation. 

A protective housing or additional shield could be used. 

Main supply must be able to be disconnected. 

Page 10/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

**HO-P series** 

## **Performance parameters definition** 

## **Ampere-turns and amperes** 

**==> picture [220 x 132] intentionally omitted <==**

**----- Start of picture text -----**<br>
I P [(DC) ]<br>I P1<br>t 2<br>0 A<br>                     t 1  t<br>- I P1<br>Figure 2:  Current cycle used to measure magnetic and<br>electrical offset<br>(transducer supplied)<br>**----- End of picture text -----**<br>


The transducer is sensitive to the primary current linkage ΘP (also called ampere-turns). 

- ΘP = _N_ P· _I_ P (At) 

Where _N_ P is the number of primary turn (depending on the connection of the primary jumpers) 

Caution: As most applications will use the transducer with only one single primary turn ( _N_ P = 1), much of this datasheet is written in terms of primary current instead of current linkages. However, the ampere-turns (At) unit is used to emphasis that current linkages are intended and applicable. 

## **Electrical offset** 

## **Transducer simplified model** 

The electrical offset _V_ can either be measured when OE the ferro-magnetic parts of the transducer are: 

The static model of the transducer at temperature _T_ A is: _V_ out = _G_ ·ΘP + overall error (mV) In which error = 

- ●completely demagnetized, which is difficult to realize, 

_εG_ ·ΘP· _G_ + _ε_ L··ΘP· _G_ + _TCG_ ·( _T_ A-25)·ΘP· _G + V_ OE + _TCV_ OE·( _T_ A-25) (mV) 

- ●or in a known magnetization state, like in the current cycle shown in figure 2. 

With: ΘP = _N_ P· _I_ P :  primary current linkage (At) ΘP max :  max primary current linkage applied to the transducer (A/t) _V_ out : output voltage (V) _T_ A : ambient operating temperature (°C) _V_ OE : electrical offset voltage (V) _TCV_ OE : temperature coefficient of _V_ OE (mV/K) _G_ : sensitivity of the transducer (V/At) _TCG_ : temperature coefficient of _G (%/K) ε_ G : sensitivity error (%) _ε_ L : linearity error for ΘP (%) 

**==> picture [244 x 46] intentionally omitted <==**

Note: the transducer has to be demagnetized prior to the application of the current cycle (for example with a demagnetization tunnel). 

## **Overall accuracy** 

The overall accuracy at 25 °C _XG_ is the error in the - _I_ PN .. + _I_ PN range, relative to the rated value _I_ PN. It includes: 

This model is valid for primary ampere-turns ΘP between -ΘP max and +ΘP max only. 

## **Sensitivity and linearity** 

- ●the electrical offset _V_ OE 

To measure sensitivity and linearity, the primary current (DC) is cycled from 0 to _I_ P, then to - _I_ P and back to 0 (equally spaced _I_ P/10 steps). The sensitivity _G_ is defined as the slope of the linear regression line for a cycle between ± _I_ PN. 

- ●the sensitivity error _εG_ 

- ●the linearity error _ε_ L (to _I_ PN) (%) 

## **Response and reaction times** 

The linearity error εL is the maximum positive or negative difference between the measured points and the linear regression line, expressed in % of _I_ PN. 

The response time figure 18. _t_ r and the reaction time _t_ ra are shown in 

Both depend on the primary current d _i/_ d _t_ . They are measured at nominal ampere-turns. 

## **Magnetic offset** 

**==> picture [405 x 120] intentionally omitted <==**

The magnetic offset voltage _V_ OM is the consequence of a current on the primary side (“memory effect” of the transducer’s ferromagnetic parts). It is measured using the following primary current cycle. _V_ OM depends on the current value _I_ P1 ( _I_ P1> _I_ PM). 

_Figure 3: Response time t_ r _and reaction time t_ ra 

Page 11/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com 

**HO-P series** 

**Dimensions HO 6-P, HO 10-P, HO 25-P** (mm, general linear tolerance ±0.5 mm) 

**==> picture [512 x 422] intentionally omitted <==**

**----- Start of picture text -----**<br>
Operation principle<br>OUT<br>12 47nF + U c<br>0V<br>5Ω 3 4.7nF<br>V out<br>200 Ω 4 47nF V ref (IN/OUT)<br>5 >10kΩ<br>OCD<br>Ip<br>IN<br>+ U c<br>0V<br>V out d CI d Cp<br>V ref (IN/OUT)<br>OCD<br>**----- End of picture text -----**<br>


**Remarks** 

·There are 6 retention pins which have to be used only for retention as well as into the section called "Assembly on PCB". ·The pimary conductor to be measured should go through the aperture 8 × 8 mm. 

Page 12/12 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

21October2014/Version 3 

www.lem.com