HAC24B150H-10

_Datasheet_ **Panel Mount** 

## _**HAC Series**_ 

- Load Voltage range 24 to 660 VAC 

- [•][ Output rating up to 150 Arms ] 

- Zero Voltage or Instantaneous Turn-on options 

- AC or DC input control options 

- Locking Input Connector 

- Optional Transient Protection & installed Thermal Pad 

## **PRODUCT SELECTION** 

**Control Voltage                                                                                                     150 A** 3-32 VDC HAC24D150 ,HAC60D150 90-140 VAC HAC24B150 ,HAC60B150 150-270 VAC HAC24A150 ,HAC60A150 

## **AVAILABLE OPTIONS** 

**==> picture [345 x 88] intentionally omitted <==**

**----- Start of picture text -----**<br>
Control Voltage<br>A:  150-270 VAC Overvoltage Protection Switching Type<br>B:  90-140 VAC Blank:  Not Included Blank:  Zero Voltage Turn-On<br>Series D:  4-32 VDC  P:  Included (6)  -10:  Instantaneous Turn-On (5)<br>HAC 24 A 150 P H -10<br>Operating Voltage Rated Load Current Thermal Pad<br>24:  24-280 VAC 150:  150 Amps Blank:  Not Included<br>60:  48-660 VAC H:  Included<br>**----- End of picture text -----**<br>


## Required for valid part number 

For options only and not required for valid part number 

## **OUTPUT SPECIFICATIONS (1)** 

|**Description**|**HAC24x150**|**HAC60x150**|
|---|---|---|
|Operating Voltage (47-63Hz)  [Vrms]|24-280|48-660|
|Transient Overvoltage [Vpk]|600|1200|
|Maximum Off-State Leakage Current @ Rated Voltage[mA]|1|1|
|Maximum Off-State dv/dt @ Maximum Rated Voltage [V/µSec]|500|500|
|Maximum Load Current[Arms](2)|150|150|
|Minimum Load Current [Arms]|0.15|0.15|
|Maximum Surge Current [Apk] 1 Cycle 50/60 Hz|1670/1750|1670/1750|
|Maximum I²t for fusing (10msec)/(8.33msec)[A²sec]|13950/12709|13950/12709|
|Maximum On-State Voltage Drop @ Rated Current [Vrms]|1.15|1.15|
|Thermal Resistance Juncti on to Case (Rjc) [°C/W]|0.15|0.15|
|Minimum Power Factor(with Maximum load)|0.5|0.5|
|Wire Size max (solid/stranded) [AWG/ IEC mm²](3)|2/0 / 67.4|2/0 / 67.4|
|Output Terminal Nut Torque Range [in lb (Nm)|225-300 (25.4-33.9)|225-300 (25.4-33.9)|
|HP Rating UL 508/IEC60957 [HP (KW)]: 240 VAC|10(7.5)|N/A|
|HP Rating UL 508/IEC60947 [HP (KW)]: 480 VAC|N/A|25(18.75)|



**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

_Datasheet_ **Panel Mount** 

## **INPUT SPECIFICATIONS (1)** 

|**Description**|**HACxxD150**|**HACxxA150**|**HACxxB150**|
|---|---|---|---|
|Control Voltage Range|4-32 VDC(10)|150-270VAC|90-140 VAC|
|Minimum Turn-Off Voltage|4 VDC|150 VAC|90 VAC|
|Must Turn-Off Voltage|1 VDC|10  VAC|10 VAC|
|Minimum Input Current (for on-state) [mA]|9|6|7|
|Maximum Input Current [mA]|15|10|12|
|Nominal Input Impedance[Ohms]|Current Regulated|Current Regulated|Current Regulated|
|Maximum Turn-On Time[msec] (4)|½  Cycle|20|20|
|Maximum Turn-Off Time[msec]|½  Cycle|30|30|
|||||



## **GENERAL SPECIFICATIONS (1)** 

|**Description**|**Parameters**|
|---|---|
|Dielectric Strength, Input/Output (50/60Hz)|3750 Vrms|
|Dielectric Strength,Input/Output/Base(50/60Hz)|2500 Vrms|
|Minimum Insulation Resistance(@ 500 V DC)|109 Ohm|
|Maximum Capacitance,Input/Output|10 pF|
|Ambient OperatingTemperature Range|-30 to 80 °C|
|Ambient Storage Temperature Range|-40 to 125 °C|
|Weight (typical) lbs/grams|0.75/340.2|
|Housing Material|PBT 30% GF, UL 94 V-0|
|SSR Mounting Torque Range [in lbs/Nm]|18-20 (2-2.2)|
|LED Input Status Indicator (color)|YES (Green)|
|Humidity|85% non-condensing|
|Input Terminal(7)|Detachable barrier strip|



## **GENERAL NOTES** 

(1) All parameters at 25°C unless otherwise specified. 

(2) Heat sinking required, see derating curves. 

(3) TRM3/0 lug terminal must be used. 

(4) Turn-on time for Instantaneous turn-on versions is 0.02 msec. 

(5) Instantaneous turn-on version is not recommended for capacitive loads. Use zero turn-on only. 

(6) Output will self-trigger (450-600Vpk for HAC24 and 900-1200Vpk for HAC60), not suitable for capacitive loads. 

(7) Connector/Plug Not included. See Suggested Mating Connectors/Plugs 

(8) Elective Overvoltage Protection, “P” option. 

(9) Load can be wired to either SSR output terminal 1 or 2. 

(10) Increase minimum voltage by 1V for operations from -20 to -30°C 

## **WIRING DIAGRAM** 

**==> picture [172 x 222] intentionally omitted <==**

**----- Start of picture text -----**<br>
AC<br>V<br>Load<br>     L2    (    )      L1    (    )<br>LOAD SIDE<br>L2 L1<br>S O L I D  S T AT E  C O N T A C T O R<br>HAC60D150<br>INPUT 4-32  VDC<br>STATUS<br> (- /     )  (+ /     )<br>**----- End of picture text -----**<br>


**==> picture [170 x 139] intentionally omitted <==**

**----- Start of picture text -----**<br>
Input Current vs Input Voltage<br>Standard Regulated “DC” Inputs<br>25<br>20<br>15<br>10<br>5<br>0<br>0 5 10 15 20 25 30<br>DC Input Voltage<br>Input Current (mA)<br>**----- End of picture text -----**<br>


**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

_Datasheet_ **Panel Mount** 

## **MECHANICAL SPECIFICATIONS** 

Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 

**==> picture [304 x 290] intentionally omitted <==**

**----- Start of picture text -----**<br>
Standard Stud<br>0.375 [9.52] -24<br>LOAD SIDE<br>L2 L1<br>T P —<br>2.90 1.87<br>[73.7] [47.6]<br>INPUT<br>STATUS<br>Mounting<br>Hole/Slot<br>| tp] em |e 0.20 [5.0] DIA.<br>2.51 [63.7]<br>3.62 [92.0]<br>4.12 [104.6]<br>1.70<br>[43.2]<br>Max o a sl a | | [ea 1.00 |<br>0.82<br>[25.4]<br>[20.8]<br>pebo<br>**----- End of picture text -----**<br>


**==> picture [125 x 27] intentionally omitted <==**

**----- Start of picture text -----**<br>
SUGGESTED MATING<br>CONNECTORS/PLUGS (7)<br>**----- End of picture text -----**<br>


RIGHT ANGLE REAR WIRE ENTRY FRONT WIRE ENTRY Molex: 0395300002 Molex: 39533 - 3002 Molex: 0395332002 Phoenix: MVSTBW 2,5/ 2 - ST - 5,08 Phoenix: MSTB 2,5/ 2 - ST - 5,08 Phoenix: MVSTBR 2,5/ 2 - ST - 5,08 

**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

_Datasheet_ **Panel Mount** 

## **SURGE CURRENT INFORMATION** 

**==> picture [334 x 165] intentionally omitted <==**

**----- Start of picture text -----**<br>
150 A<br>1800<br>1600<br>1400<br>1200<br>1000<br>800<br>600<br>400<br>200<br>0<br>0.01 0.1 1 10<br>Surge Duration (Secs)<br>Surge Current (Amp)<br>**----- End of picture text -----**<br>


Non repetitive peak surge current at Tj initial 40°C 

## **THERMAL DERATE INFORMATION (2)** 

## **HACxxA150** 

## **HACxxB150,HACxxD150** 

**==> picture [499 x 151] intentionally omitted <==**

**----- Start of picture text -----**<br>
0.25ºC/W 0.36ºC/W 0.50ºC/W 0.25ºC/W 0.36ºC/W 0.50ºC/W<br>150 150<br>125 125<br>100 100<br>75 75<br>50 50<br>25 25<br>0 0<br>20 30 40 50 60 70 80 20 30 40 50 60 70 80<br>Ambient Temperature (ºC) Ambient Temperature (ºC)<br>Load Current (Amps) Load Current (Amps)<br>**----- End of picture text -----**<br>


**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

_Datasheet_ **Panel Mount** 

## **EQUIVALENT CIRCUIT BLOCK DIAGRAM** 

**==> picture [113 x 11] intentionally omitted <==**

**----- Start of picture text -----**<br>
Diagram: HAC AC control<br>**----- End of picture text -----**<br>


**==> picture [335 x 200] intentionally omitted <==**

**----- Start of picture text -----**<br>
L2<br>AC AC<br>Current<br>Limiter<br>ConverterAC/DC TriggerCircuit (8) (9)<br>AC AC<br>L1<br>Diagram: HAC DC control<br>L2<br>-DC AC<br>Trigger (8)<br>Circuit (9)<br>+DC AC<br>Current L1<br>Limiter<br>**----- End of picture text -----**<br>


## **ACCESSORIES** 

## **Recommended Accessories** 

**==> picture [233 x 54] intentionally omitted <==**

**----- Start of picture text -----**<br>
Hardware Kit Heat Sink Thermal Resistance Lug Terminal Thermal Pad<br>Part No. [ºC/W]<br>HK1 HS053 0.5 TRM3/0 HSP-5<br>HS033 0.36<br>HS023 0.25<br>**----- End of picture text -----**<br>


## **AGENCY APPROVALS** 

## **Agency Approvals** 

Designed in accordance with the requirements of IEC 62314 

IEC 61000-4-2 : Electrostatic Discharge: Level 3 IEC 61000-4-4 : Electrically Fast Transients: Level 3 IEC 61000-4-5 : Electricsl Surges: Level 3 E116949 

Rev. 091316 

**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

_Datasheet_ **Panel Mount** 

## **DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO /** 危险 

**RISQUE DE GEFAHR EINES RISCHIO DI** 存在电击、 **DESCHARGE ELEKTRISCHE SCOSSA** 爆炸或电弧 **ELECTRIQUE N SCHLAGES ELETTRICA O** 闪烁危险 **OU EXPLOSION ODER EINER DELL’ESPLOSIONE.** • Eteindre **EXPLOSION.** • Spenga tutta • 在操作此设 toutes les • Stellen Sie l'alimentazione 备之前请先 sources jeglichen che fornisce 关闭电源。 d'énergie de Strom ab, der questa cet appareil dieses Gerät apparecchiatura avant de versorgt, bevor prima di lavorare 若不遵守这些说明， travailler Sie an dem a questa 可能会导致严重的 dessus de cet Gerät Arbeiten apparecchiatura 人身伤害甚至死亡。 appareil durchführen • Vor dem • Verificare tutti • Vérifier tous Drehen auf i collegamenti connections, et e sostituire Energie alle remettre tous Anschlüsse tutte le coperture couverts en prima überprüfen olace avant de dell’accensione und alle mettre sous Abdeckungen **L'omissione di De non-suivi de** ersetzen. **queste istruzioni ces instructions Unterlassung provocherà la provoquera la dieser morte o mort ou des Anweisungen lesioni serie lésions sérieuses können zum sérieuses. Tode oder zu schweren Verletzungen führen.** 

**HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH.** 

**RIESGO DE DESCARGA ELECTRICA O EXPLOSION.** 

- Desconectar 

- • Disconnect all todos los power before suministros de installing or energia a este working with equipo antes this equipment. de trabajar con este equipo. 

- Verify all connections • Verificar todas and replace all las conexiones covers before y colocar todas turning on las tapas antes power. de energizer el equipo. 

y colocar todas • Vérifier tous las tapas antes connections, et de energizer remettre tous el equipo. couverts en olace avant de **El** mettre sous **incumplimiento de estas De non-suivi de instrucciones ces instructions puede provocar provoquera la la muerte o mort ou des lesiones serias. lésions sérieuses** 

**Failure to follow these instructions will result in death or serious injury.** 

## **WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA /** 警告 

## **RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE** 

- The product's side panels may be hot, allow 

- the product to cool before touching. 

- Follow proper mounting instructions including 

- torque values. 

- Do not allow liquids or foreign objects to enter 

- this product. 

**Failure to follow these instructions can result in serious injury, or equipment damage.** 

## **RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD** 

**•** Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. 

- Respetar las instrucciones de montaje, y en 

- particular los pares de apretado. 

- No dejar que penetren líquidos o cuerpos 

- extraños en el producto. 

**Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales.** 

## **GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG** 

## **RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER** 

**•** Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. 

   - Die Seitenwände können heiß sein. Lassen Sie 

   - das Produkt abkühlen, bevor Sie es berühren. 

   - Beachten Sie die Montageanweisungen, 

- Respecter les consignes de montage, et 

- notamment les couples de serrage. 

   - Führen Sie keine Flüssigkeiten oder 

   - Fremdkörper in das Produkt ein. 

- Ne pas laisser pénétrer de liquide ni de corps 

- étrangers à l'intérieur du produit. 

**Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann des lésions corporelles graves ou des Körperverletzung oder Materialschäden dommages matériels. zur Folge haben.** 

## 材料损坏和高温外壳的危险性 

## **RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO** 

- 产品的一侧面板可能很热，在其冷却前请 

- **•** I pannelli laterali dell'apparecchio possono 不要触碰。 scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 prima di toccarlo. 

   - 请勿让液体及其他异物进入本产品。 

- Seguire le istruzioni di montaggio corrette. 

- Non far entrare liquidi o oggetti estranei in questo 

- apparecchio. 

> **La mancata osservanza di questa precauzione può** 如不能正确执行这些操作说明， 

> **causare gravi rischi per l'incolumità personale o** 极有可能造成严重人体伤害或者设备的损坏。 **danni alle apparecchiature.** 

**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

_Datasheet_ **Panel Mount** 

## **ANNEX - ENVIROMENTAL INFORMATION** 

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. 

|Part<br>Name|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|
|---|---|---|---|---|---|---|
||Lead<br>(Pb)|Mercury<br>(Hg)|Cadmium<br>(Cd)|Hexavalent<br>Chromium<br>(Cr (VI))|Polybrominated<br>biphenyls<br>(PBB)|Polybrominated<br>diphenyl ethers<br>(PBDE)|
|Semiconductor die|||||||
|Solder|||||||



## 附件 - 环保信息 

此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 

|件<br>部<br>名称|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|
|---|---|---|---|---|---|---|
||铅<br>(Pb)|汞<br>(Hg)|镉<br>(Cd)|六价铬<br>(Cr (VI))|多溴联苯<br>(PBB)|多溴二苯醚<br>(PBDE)|
|半导体芯片|||||||
|焊接点|||||||



**==> picture [96 x 94] intentionally omitted <==**

**----- Start of picture text -----**<br>
50<br>**----- End of picture text -----**<br>


**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 

Datasheets provided by Sensata Technologies, Inc., its subsidiaries and/or affiliates (“Sensata”) are solely intended to assist third parties (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, valuation, and judgment in designing Buyer’s systems and products. Sensata datasheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular datasheet. Sensata may make corrections, enhancements, improvements, and other changes to its datasheets or components without notice. 

Buyers are authorized to use Sensata datasheets with the Sensata component(s) identified in each particular datasheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATASHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATASHEETS OR USE OF THE DATASHEETS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATASHEETS OR USE THEREOF. 

All products are sold subject to Sensata’s terms and conditions of sale supplied at www.sensata.com. SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY, AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONSRELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA 

## **CONTACT US** 

**Regional head offices: United States of America** Sensata Technologies Attleboro, MA **Phone:** 508-236-3800 **E-mail:** support@sensata.com **Netherlands** Sensata Technologies Holland B.V. Hengelo **Phone:** +31 74 357 8000 **E-mail:** support@sensata.com **China** Sensata Technologies China Co., Ltd. Shanghai **Phone:** +8621 2306 1500 **E-mail:** support@sensata.com 

Copyright © 2023 Sensata Technologies, Inc. 

sensata.com