FSP220FEB-B204

## _**SPARKLE POWER INC.**_ 

## **FSP220-50FEB** 

**Meet 80plus (Bronze) Active PFC Circuit / Full Range Input Flex Power Supply Safety Meet 62368** 

**Fremont Office** 48502 Kato Road. Fremont, CA 94538 Tel: (408) 519-8888 Fax: (408) 519-9999 

**Los Angeles Office** 17071 Green Dr. City of Industry, CA 91745 Tel: (626) 839-7180 Fax: (626) 839-3395 

sparkle@sparklepower.com www.sparklepower.com 

**06/04/2018** 

**®** 

## _http://www.sparklepower.com/_ 

## **MODEL:FSP220-50FEB** 

## **Revision History** 

|Rev|**Description**||Date||Author|
|---|---|---|---|---|---|
|1.0|First Edition|2018/6/4||JIMMY||
|1.1||||||
|1.2||||||
|||||||
|||||||
|||||||
|||||||
|||||||



2 

## **1. GENERAL DESCRIPTION AND SCOPE** 

This is the specification of Model **FSP220-50FEB** ; AC-line powered switching power supply with active PFC (Power Factor Correction) circuit, meet EN61000-3-2 and with Full Range Input features.  Designed and manufactured by FSP GROUP. 

The specification below is intended to describe as detailedly as possible the functions and performance of the subject power supply. Any comment or additional requirements to this specification from our customers will be highly appreciated and treated as a new target for us to approach. 

## **2. REFERENCE DOCUMENTS** 

The subject power supply will meet the EMI requirements and obtain main safety approvals as following: 

## 2.1 EMI REGULATORY 

- FCC Part 15 Subpart J, Class ‘B’ 115 Vac operation. 

- CISPR 32 Class ‘B’ 230 Vac operation. 

## **3. PHYSICAL REQUIREMENTS** 

## 3.1 MECHANICAL SPECIFICATIONS 

The mechanical drawing of the subject power supply, which indicate the form factor, location of the mounting holes, location, the length of the connectors, and other physical specifications of the subject power supply. Please refer to the attachment drawing. 

## **4. ELECTRICAL REQUIREMENTS** 

## 4.1 OUTPUT ELECTRICAL REQUIREMENTS 

The subject power supply will meet all electrical specifications below, over the full operation temperature range and dynamic load regulation. 

3 

## 4.1.1. OUTPUT RATING 

|Output|Nominal|Regulation|Ripple/Noise|Min|Max|
|---|---|---|---|---|---|
|1|+3.3V|���|50mV|0.0A|8.0 A|
|2|+5V|���|50mV|0.0 A|12.0 A|
|3|+12V|���|120mV|0.0 A|14.0 A|
|4|-12V|����|120mV|0.0 A|0.3A|
|5|+5VSB|���|50mV|0.0 A|2.5A|



� –12V,+3.3V, +5V,+12V will have the regulation to �10% when all load take off. 

The +3.3V and +5V total output shall not exceed 61watts. The total output for this subject power supply is 220 watts. Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter with 20MHz cutoff frequency.  Outputs shall bypassed at the connector with a 0.1uF ceramic disk capacitor and a 10uF electrolytic capacitor to simulate system loading. 

## 4.1.2. LOAD CAPACITY SPECIFICATIONS 

The cross regulation defined as follows, the voltage regulation limits DC include DC Output ripple & noise. 

|LOAD|+3.3V|+5V|+12V|-12V|5VSB|
|---|---|---|---|---|---|
|LOAD1|5.07A|7.60A|12.57A|0.27A|2.24A|
|LOAD2|0 A|12 A|4A|0.01A|0A|
|LOAD3|8.0 A|0.2 A|0.5A|0A|0A|
|LOAD4|0 A|0.2 A|14.0A|0.01A|0A|
|LOAD5|0 A|0.2 A|0.5A|0A|0A|



## 4.1.3. HOLD-UP TIME @80% LOAD 

115V / 60Hz : 16 mSec. Minimum. 

230V / 50Hz : 16 mSec. Minimum. 

## 4.1.4.OUTPUT RISE TIME 

(10% TO 90% OF FINAL OUTPUT VALUE, @FULL LOAD) 

115V-rms  or  230V-rms    +5Vdc�20ms Maximum 

- +3.3Vdc�20ms Maximum 

+12Vdc�20ms Maximum 

- -12Vdc�20ms Maximum 

4 

## 4.1.5.OVER VOLTAGE PROTECTION 

|Voltage Source|Protection Point|
|---|---|
|+ 3.3 Vdc|3.7V-4.5V|
|+5Vdc|5.7V-6.5V|
|+12Vdc|13.3V – 15.5V|



## 4.1.6. OVER-CURRENT PROTECTION 

|OUTPUT VOLTAGE|OCP|
|---|---|
|+3.3V|10A-15A|
|+5V|15A-20A|
|+12V|16A-24A|



## 4.1.7. OVER  POWER  PROTECTION 

Total output shall not exceed 220 watts , in the event of an output total power condition on output , If the total exceed 150% , the power supply will shutdown and latch off without damage to the power supply. 

## 4.1.8.POWER GOOD SIGNAL 

The power good signal is a TTL compatible signal for the purpose of initiating an orderly star-up procedure under normal input operating conditions.  This signal is asserted (low) until +5Vdc has reached 4.75 volts during power up. Characteristics: 

TTL signal asserted (low state) : less than 0.5V while sinking 10mA. 

TTL signal asserted (high state): greater than 4.75V while sourcing 500uA. 

High state output impedance: less or equal to 1Kohm from output to common. 

|POWER GOOD@115/230V,Typical(50%)LOAD|100 –500mSec.|
|---|---|
|POWER FAIL@115/230V,Typical(50%)LOAD|1 mSec. minimum|



5 

**==> picture [404 x 170] intentionally omitted <==**

**----- Start of picture text -----**<br>
PS_ON ON OFF<br>P.G. SENSE<br>LEVEL 95%<br>+5V O/P<br>P.G. T1 < 20mS<br>T2 = 100~500mS<br>T3 > 1mS<br>T1 T2<br>T3<br>**----- End of picture text -----**<br>


## 4.2. OUTPUT TRANSIENT LOAD RESPONSE 

The  output  voltages  shall  remain  within  the  limits  specified  in  4.1.1  output  rating  table  in page 4 for the step loading and within the limits specified in Table 1 for the capacitive loading. The load transient repetition rate shall be tested between 50Hz and 5 kHz at duty cycles ranging from 10%-90%. The load transient repetition rate is only a test specification. The step load may occur anywhere within the MIN load to the MAX load shown in Table 1. 

**Table 1: Transient Load Reguirements** 

## 4.3. INPUT ELECTRICAL SPECIFICATIONS 

## 4.3.1. VOLTAGE RANGE 

**==> picture [366 x 21] intentionally omitted <==**

**----- Start of picture text -----**<br>
||||
|---|---|---|
|PARAMETER|UNITS|
|V-in Range|90 - 264|V-rms|

**----- End of picture text -----**<br>


## 4.3.2. INPUT FREQUENCY 

INPUT FREQUENCY 47–63Hz 

## 4.3.3. INRUSH CURRENT 

## (Cold start: 25 deg. C) 

**==> picture [254 x 21] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||
|---|---|
|115V|No damage|
|230V|No damage|

**----- End of picture text -----**<br>


6 

## 4.3.4. INPUT LINE CURRENT 

|115V|4.0 Amps – rms maximum|
|---|---|
|230V|2.0 Amps – rms maximum|



## 4.4. EFFICIENCY 

||Full load(100%)|Typical load(50%)|Light load(20%)|
|---|---|---|---|
|115VAC|82%|85%|82%|
|230VAC|82%|85%|82%|



## (loading shown in Amps) 

|Loading|+12V|+5V|+3.3V|-12V|+5Vsb|
|---|---|---|---|---|---|
|Full(100%)|12.57|7.60|5.07|0.27|2.24|
|Typical(50%)|6.28|3.80|2.53|0.13|1.12|
|Light(20%)|2.51|1.52|1.01|0.05|0.45|



## 4.5. Standby Power Consumption (5Vsb): 

Efficiency > 45% @ 5Vsb/45mA &230Vac input (2013 Lot 6) Efficiency > 55% @ 5Vsb/550mA &230Vac input Efficiency > 70% @ 5Vsb/1A &230Vac input Efficiency > 70% @ 5Vsb/2.5A &230Vac input 

## 4.6. PS_ ON# 

PS_ON# is an active-low, TTL-compatible signal that allows a motherboard to remotely control the power supply in conjunction with features such as soft on/off, Wake on LAN+, or wake-on-modem. When PS_ON# is pulled to TTL low, the power supply should turn on the five main DC output rails: +12VDC,+5VDC,+3.3VDC and –12VDC.  When PS_ON# is pulled to TTL high or opencircuited, the DC output rails should not deliver current and should be held at zero potential with respect to ground. PS_ON# has no effect on the +5VSB output, which is always enabled whenever the AC power is present.  (PS_ON# Signal Characteristics) 

The power supply shall provide an internal pull-up to TTL high. The power supply shall also provide debounce circuitry on PS_ON#  to prevent it from oscillating on/off at startup when activated by a mechanical switch.  The DC output enable circuitry must be SELV-compliant. 

## **PS_ON# Signal Characteristics** 

||Min.|Max.|
|---|---|---|
|VIL,Input Low Voltage|0.0V|0.8V|
|IIL,Input Low Current(Vin = 0.4V)||-1.6mA|
|VIH,Input High Voltage (lin = -200�A)|2.0V||
|VIH OPEN circuit,lin = 0||5.25V|



7 

## **5. ENVIRONMENTAL REQUIREMENTS** 

The power supply will be compliant with each item in this specification for the following Environmental conditions. 

## 5.1. TEMPERATURE RANGE 

|Operating|0 to +50 deg. C FOR 220W|
|---|---|
|Storage|-20 to +80 deg. C|
|2. HUMIDITY||
|Operating|85% RH,Non-condensing|
|Storage|95% RH,Non-condensing|



## 5.2. HUMIDITY 

## 5.3. VIBRATION 

The subject power supply will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. 

Vibration Operation, 0.01g²/Hz at 5 Hz sloping to 0.02g²/Hz at 20 Hz, and maintaining 0.02g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13gRMS. The duration shall be 20 minutes per axis for all three axes on all samples. 

Plane of vibration to be along three mutually perpendicular axes. 

## 5.4. SHOCK 

The subject power supplies will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. 

Storage    40G, 9 mSec. half-sine wave pulse in both directions on three mutually 

perpendicular  axes. 

Operating  10G, 11mSec. half-sine wave pulse in both directions on three mutually 

Perpendicular  axes. 

## 5.5 COOLING SPECIFICATIONS 

## 5.5.1. The PSU is cooled by a self-contained  FAN, 40mm, 12VDC. 

## **5.6 ALTITUDE** 

The power supply is applied for tropical climates and use at altitudes not exceeding 5000m above Sea level 

8 

## **6. SAFETY** 

## 6.1. LEAKAGE CURRENT 

The leakage current from AC to safety ground will not exceed 3.5 mA-rms at 264Vac, 50 Hz. 

## **7. ELECTORMAGNETIC COMPATIBILITY** 

## 7.1 LINE CONDUCTED EMI 

The subject power supplies will meet FCC class B requirements . 

## 7.2. RADIATED EMI 

The subject power supplies will meet FCC and CISPR 32 requirements . 

## **8. LABELLING** 

Label marking will be permanent, legible and complied with all agency requirements. 

## 8.1. MODEL NUMBER LABEL 

Labels will be affixed to the sides of the power supply showing the following: 

   - Manufacturer’s name and logo. 

- Model no., serial no., revision level, location of manufacturer. 

- The total power output and the maximum load for each output. 

   - AC input rating. 

## 8.2 DC OUTPUT IDENTIFICATION 

Each output connector will be labeled. 

## **9. RELIABILITY** 

## 9.1. MTBF 

The power supply have a minimum predicted MTBF(MIL-HDBK-217) of 100,000 hours of continuous operation at 25�, maximum-output load, and nominal AC input voltage. 

9