FHSAC1-230-45CED

## FHSAC1-230-45CED 

**==> picture [71 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>**----- End of picture text -----**<br>


## **Programmable Constant Current LED Driver** 

- Emergency LED Driver 

-  Universal Voltage: 220-240VAC 

-  Output Voltage Range: 11-50VDC 

   - Output Wattage: 45W 

   - Dimming Type: DALI V1.0 and I2C/Bluetooth 

   - Dimming Range: 1%-100% @ AC mode 

-  Output Current: 250-1400mA 

## **General Specifications** 

Input Voltage / Frequency 220-240VAC , 47-63Hz Input Current 0.27A@220V Input Power 58W Standby Power <0.5W Power Factor >0.9@half load THD <20%@half load0%@half loadhalf loadalf loadlf loadoad 

<20%@half load0%@half loadhalf loadalf loadlf loadoad 

Output Type Constant Current Current Rated 250-1400mA,(R-set 250-1400) ±5% When output type is CC Output Voltage Range 11-50VDC Output Power 45W Normal Mode / 3W 180 min or 7W 90 min EM Output Class SELV Dimming Controller Type DALI V1.0 and I2C/Bluetooth Dimming Range(%) 1% to100%@AC mode Number of Output Channels 1Channel Input Surge Protection Line-Neutral 2kV, Line & Neutral-Ground 2.5kV Protections Input Under Voltage Protection Overload Protection Input Short Circuit Protection Battery Deep Discharge Protection Over Temperature Protection RFI/EMI EN55015 Ambient Operating Temperature Range 0°C To 40°C(32°F To 104F°) Sound Rating A Battery Type LiFePO4 Battery Voltage 9.6V Battery Capacity 1.5Ah Battery Charge Current 200mA Battery Recharge Time 12Hours Battery Discharge Time 0°C - 40°C IP Rating IP   20 Service Life 50,000 hours Warranty 5 years Safety Standards IEC/EN61347-1,IEC/EN61347-2-7,IEC/EN 61347-2-13,IEC/EN 60598-1 IEC/EN 60598-2-22,IEC 62384,EN 62493,IEC / EN 62034 EN 61547,EN 55015 , EN 61000-3-2 , EN 61000-3-3E, N 61000-4-2,EN61000-4-3 EN61000-4-4,EN61000-4-5,EN61000-4-6,EN61000-4-8,EN61000-4-11,EN61000-4-29 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** 

Page 1 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [71 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>**----- End of picture text -----**<br>


## **Mechanical Data** 

**==> picture [428 x 138] intentionally omitted <==**

**----- Start of picture text -----**<br>
7.89”<br>(200.5mm)<br>ø0.18”<br>(ø4.5mm)<br>a 9.21”<br>3.23”<br>(82mm)<br>**----- End of picture text -----**<br>


**==> picture [32 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
(234mm)<br>**----- End of picture text -----**<br>


## **TOP VIEW** 

**==> picture [212 x 66] intentionally omitted <==**

**----- Start of picture text -----**<br>
EE<br>SIDE VIEW<br>1.34”<br>(34mm)<br>**----- End of picture text -----**<br>


**Tolerance=±** 0 **.** 0 **2"[** 05mm **. ]** 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** 

Page 2 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [71 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>**----- End of picture text -----**<br>


## **Important Safety Instructions** 

**When using electrical equipment and this lighting device basic safety precaution should be followed at all times including but not limited to the following:** 

## **PLEASE READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY** 

**Important: An un-switched AC power source of 220VAC to 240VAC is required.[Important: Double insulation used between the supply and battery circuit.] Important: Intermittent re-charging circuit. Important: The recharging device remains safe after abnormal operating condition.** 

**Caution** : Do not let power supply cords touch hot surfaces. **Caution** : Do not mount near gas or electric heaters. **Caution** : Do not use outdoors. 

**Caution: Battery is rechargeable LiFePO4 type and must be recycled or disposed of properly.** 

Do not use this emergency driver with accessory equipment other than recommended by manufacturer; failure to follow this may cause an unsafe condition. Servicing should only be performed by qualified service personnel. 

Do not use this emergency driver for other than intended use. 

Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. 

## **Important:  Indicator (LED light) illuminated indicates battery in charge mode when AC power is applied.** 

It is recommended and required by applicable code to test emergency function to ensure proper operation of the system; push the test switch for thirty (30) seconds every 30 days to ensure the emergency driver is 

functioning as by illuminating the LED light source.  Conduct a ninety minute (90) discharge test one time (1) per year; LED light source should be illuminated for a minimum of ninety minutes (90). 

**ASSEMBLY and FIELD INSTALLATION WIRING:  WARNING:** AC power must be o ffbefore proceeding with assembly or installation of emergency driver. 

**TESTING SYSTEM:** The emergency battery requires a charge minimum of one (1) hour before testing the circuit.  A full charge requires twelve (12) hours. 

**IMPORTANT:** In order to maintain proper operation and warranty coverage, the battery must be recharged once per year prior to installation. 

**==> picture [32 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
Figure 1<br>**----- End of picture text -----**<br>


**Figure 2** 

**==> picture [446 x 144] intentionally omitted <==**

**----- Start of picture text -----**<br>
R SET Curve - Vo vs Io(Max) Curve<br>1500 1400<br>1400 || | IN<br>1300 1200<br>1200<br>1100 1000<br>| 1000 eeot SSS<br>900<br>ay 800 A CV=30V 800 +S<br>700<br>SEA 600 Yr TTATE tl CV=50V 600 EERE<br>500<br>400 COAT 400 PLY PTEERLE<br>300 SAC ER<br>200 ~ [| LM TCTEHIEEE HII 200 EERERFEEEEEE<br>1 10 100 1000 10 20 30 40 50<br>Resistor Value(Kohm)<br>Output Voltage (Vdc)<br>Io(Max) (mA)<br>**----- End of picture text -----**<br>


**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** Page 3 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**Figure 3** 

**==> picture [219 x 359] intentionally omitted <==**

**----- Start of picture text -----**<br>
Efficiency vs Output Voltage at 220Vac<br>90<br>88 750mA<br>7|<br>86 1000mA<br>aS=—ae=<br>1250mA<br>84<br>>ae 1400mA<br>8280 (|||nn en<br>20 25 30 35 40 45 50<br>Output Voltage(Vdc)<br>Lifetime vs Tcase<br>140<br>120 CTT<br>100<br>PN<br>80 CAEN<br>60 COC<br>40<br>20 FEEEESPRRSCE><br>0<br>CHE<br>50 55 60 65 70 75 80 85 90<br>Tcase （℃）<br>Efficiency (%)<br>Lifetime (Khrs)<br>**----- End of picture text -----**<br>


**Figure 5** 

**Figure 7** 

**==> picture [210 x 151] intentionally omitted <==**

**----- Start of picture text -----**<br>
Default Io vs Tcase(driver)<br>10080 ee<br>60 ee<br>40 ee<br>20 ee<br>0<br>ee —<br>50 60 70 80 90 100<br>Tcase(°C)<br>Io Ratio(%)<br>**----- End of picture text -----**<br>


**==> picture [71 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>**----- End of picture text -----**<br>


**Figure 4** 

**==> picture [213 x 143] intentionally omitted <==**

**----- Start of picture text -----**<br>
Power Factor vs Output Power<br>1.000<br>0.980<br>230V<br>0.960<br>-<br>0.940<br>0.920<br>0.900<br>20 25 30 35 40 45<br>Output Power (W)<br>Power Factor<br>**----- End of picture text -----**<br>


**Figure 6** 

**==> picture [226 x 158] intentionally omitted <==**

**----- Start of picture text -----**<br>
THD vs Output Power<br>30<br>25<br>20 Eeaeeeee<br>_ 230V<br>15<br>SEE<br>10<br>5 ENS<br>E<br>0 EASA<br>5 15 25 35 45<br>Output Power (W)<br>THD(%)<br>**----- End of picture text -----**<br>


**Figure 8** 

**==> picture [216 x 150] intentionally omitted <==**

**----- Start of picture text -----**<br>
Default Io vs Ext.NTC Curve<br>100806040 FEEEEEEFEEEEERZEEEEEEEEEE E EEEEEH E RET<br>20 PEEEEEEEEEEEEEEEECEHEEEEEEE<br>0<br>0 PERE 1 2 3 4 EE 5 6 EEE 7 8 9 10 EEE 11 12 13 EEEELEH 14 15 16 17 18 19 20<br>Resistor of Ext.NTC on Module (Kohm)<br>Io Ratio (%)<br>**----- End of picture text -----**<br>


**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** Page 4 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [71 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>**----- End of picture text -----**<br>


**==> picture [70 x 8] intentionally omitted <==**

**----- Start of picture text -----**<br>
     LED ARRAY<br>**----- End of picture text -----**<br>


**==> picture [525 x 339] intentionally omitted <==**

**----- Start of picture text -----**<br>
LED-<br>LED+<br>NTC / PRG-<br>NTC/TPSB-100E<br>NTC / PRG+ <——<br>     TEST (The test switch can be used together with<br><— F SWITCH Fulham FHSWLPWH Wall Plate.)<br>DALI - DALI<br>DALI+ < — __<br>L2<br>po N<br>N<br>WALL SWITCH L<br>L1<br>GND<br>E<br> FHSAC1-230-45CED<br>E<br>DALI -<br>L1 DALI+<br>Loop Out<br>N<br>L2<br>— Pulse Dimming switch<br>Description: The Fulham FHSWLPWH Wall Plate can be used when remote mounting the Lighted Push Button Test Switch<br>  ( LPBTS) next to the fixture, on the wall or in any location within the maximum remote mounting distance (15 meters) of the Lighted Push<br>Button Test Switch (LPBTS).<br> FHSAC1-230-45CED<br>**----- End of picture text -----**<br>


**Wall plate and screw color: white with black lettering** 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** 

Page 5 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [71 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>**----- End of picture text -----**<br>


Self-Diagnostic tests to insure the unit is properly functional . It will test the following parameters: *Battery-Checks to insure battery is properly connected and has sufficient capacity for 180 minutes when set to 3W or 90 minutes when set to 7W 

*LED load-Insures LED load is connected properly and functional. 

- *Charging circuit-Insures unit charging circuit is functioning properly. 

Any errors will be shown via the indicator light as per the table below: 

|**LED indicators on TEST SW**|**System Status**|
|---|---|
|Permanentgreen|System OK|
|Slow flashing green<br>(1 sec on – 1 sec off)|Self-Diagnostic process underway|
|Flashing Red<br>(4 sec on – 1 sec off)|Battery not connected, check BAT pack|
|Solid Red|Load failure, check EM LED load.|
|Slow flashing red<br>(1 sec on – 1 sec off)|Battery failure, replace BAT pack.|
|Fast flashing red<br>(0,5 sec on – 0,5 sec off)|Charge circuit error, replace EM Driver.|
|Both Green & Red off|EM Mode|



## TEST SWITCH OPERATIONS: 

## Emergency Test Mode 

1. Press and Hold Test Button to test Emergency Mode. 

   - This can be done in all normal AC powered situations including dimmed to o ffand switched off 

## Manual Self-Diagnostic 

1. Quickly Press Test Button 3 times within 3 seconds to manually activate Self-Diagnostic cycle. This will test the unit for 180 minutes when EM power set for 3W or for 90 minutes when EM power is set for 7W. 

2. To Exit the Self-Diagnostic cycle, Press and Hold Test Button for 5 seconds 

## Enable / Disable Auto Self-Diagnostic 

1. Press and Hold Test Button for 3 seconds 

2. Release and Quickly Press Test Button 2 times 

3. Press and Hold Test Button again for 3 seconds 

4. Green Indicator on Test Button will flash for 5 seconds indicating the Enabled or Disabled Status ： 

   - Short o ff/ Long on   = Enabled 

   - Long o ff/ short on = Disabled 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** 

Page 6 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [74 x 25] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>monk <4<br>**----- End of picture text -----**<br>


## PROGRAMMING: 

The following features can be programmed on this driver using the Fulham SmartSet TPSB-100E Handset: 

- Output Current - 250mA to 1400mA 

- Output EM power - 3W factory default 

- Enable / Disable Auto Self-Diagnostic Function 

- Dimming :DALI 

In order to configure the last 3 items, the TPSB-100E must be in FULL FEATURE mode. 

The Output Current, EM Power, Dimming Profile and Auto Self-Diagnostic Status can also be configured by using the Fulham SmartSet PC software. 

*For more detailed programming instructions please see our Programming Instructions and Design Guide found on our website. 

- https://www.fulham.com/PDFs/SpecSheets/Fulham-Design-Guide-Programmable-Drivers.pdf 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** Page 7 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [74 x 24] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>1x<br>**----- End of picture text -----**<br>


## **Guidelines** 

## **Grounding** 

- Driver must be grounded by means of the Driver case. 

## **Over temperature protection** 

- The Fulham Hotspot Plus LED drivers are protected against thermal overload. If the temperature limit is exceeded, the output current is reduced. 

## **LED load** 

- Fulham Hotspot Plus LED drivers are designed to drive passive LEDs, -COB's and -LED assemblies Proper function is not guaranteed when (LED) loads with active components are used. 

## **Mounting / Cooling** 

- Above an output power of 20W, the driver needs to be mounted on a heat conductive surface of at least 200cm². Always test if the surface is sufficient enough before installing the driver. 

## **Short-circuit protection** 

- In case of a short circuit the LED driver switches to protection mode. After the removal of the short-circuit the LED driver will recover automatically. 

## **No-load Operation** 

- In no-load operation the output voltage will not exceed the specified open circuit output voltage. 

## **Hot Swapping** 

- This driver does not support hot swapping of the LEDs 

## **Remote Mounting** 

- Up to 15ft with 18AWG. Contact Fulham for higher remoute distance. 

## **Battery Maintenance** 

- In order to maintain proper operation and warranty coverage, the battery must be recharged once per year prior to installation. 

## **Warranty** 

- Reference Fulham's limited Warranty: https://cdn.fulham.com/PDFs/Limited-Warranty.pdf 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** 

Page 8 of 9 2020-852 Rev A 

## FHSAC1-230-45CED 

**==> picture [74 x 24] intentionally omitted <==**

**----- Start of picture text -----**<br>
EL-T 02<br>1x<br>**----- End of picture text -----**<br>


## **Part Number Matrix** 

## D 

**==> picture [577 x 66] intentionally omitted <==**

**----- Start of picture text -----**<br>
FHS AC 1 230 45 C E D<br>LED Driver AC LED Driver LED Driver Number Input Voltage Power Case Type Standard Special Features<br>       FHS = Fire Horse EM Driver  AC= AC LED Driver 1 = Programmable Output 230 = 220V-240V 45  = 45W C= Cube or Compact  E= IEC   D=  DALI<br>**----- End of picture text -----**<br>


## **Product Image: LED Driver** 

**FHSAC1-230-45CED** 

## **Packaging** 

## **Master Carton** 

**==> picture [54 x 58] intentionally omitted <==**

**----- Start of picture text -----**<br>
y<br>349X 294X1909.08.0 1 B0.8N:4 7 0 9 8  15 0 4 6 7 4 2<br>FHSAC1-230-45CED<br>**----- End of picture text -----**<br>


OUTER DIMENSION L W H 1.145” (349mm) 0.965”(294mm) 0.623”(190mm) Net Gross QUANTITY Weight Weight 00.00lbs. 00.00lbs. (8kg.) (9kg) 15pcs. 

**Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.** Specifications subject to change without notice. 

**order@fulham.com www.fulham.com** 

Page 9 of 9 2020-852 Rev A