ENW89858A1KF

Bluetooth Module, BLE 5.1, -103 dBm, 1.7 V to 5.5 V Supply, -40 °C to 85 °C

⚠️ Reference pricing provided. In case of supply shortages, we will connect you with our trusted procurement partners to ensure your project's continuity.
Manufacturer: PANASONIC
Product type: Bluetooth Modules & Adaptors
Available until stocks are exhausted
SVHC: No SVHC (25-Jun-2025)
Interfaces: I2C, SPI, UART
Product Range: -
Certifications: FCC, ISED, RED, UKCA
Bluetooth Class: -
Bluetooth Version: Bluetooth LE 5.1
Supply Voltage Range: 1.7 V to 5.5 V
Receiver Sensitivity Rx: -103 dBm
Operating Temperature Range: -40 °C to 85 °C
Delivery and price
Units per pack	250
Price	6.32 €
Current stock	200+
Lead time	30 days
Datasheet
## PAN1782 

Bluetooth[®] Low Energy Module Product Specification Rev. 1.0 

Wireless Connectivity 

PAN1782 Bluetooth Module 

## **Overview** 

The PAN1782 is a Bluetooth 5.1 Low Energy (LE) module based on the Nordic nRF52833 single chip controller. 

## **Features** 

## **[Bluetooth ]** 

   - [LE 2 Mbps high speed PHY, LE long range ] coded PHY 

   - [LE advertising extensions (advertising on ] 40 channels total) 

   - [Channel selection algorithm #2 ] 

   - [LE secure connections ] 

- [Surface Mount Type: 15.6 mm × 8.7 mm × 2 mm ] 

- [Pin compatible hardware drop-in replacement for ] PAN1026A, PAN1762, and PAN1781 

- [Nordic nRF52833 featuring ARM][®][ Cortex][®][-M4 ] running with 64 MHz 

- [Bluetooth 5.1 LE including LE 2M and LE coded ] PHY 

- [Embedded 512 kB flash memory and 128 kB ] internal RAM 

- [128-bit AES/ECB/CCM/AAR co-processor  ] 

- [Up to 16 General Purpose I/O’s (GPIO), which ] are shared with up to 4× SPI, 2× I²C, 2× UART, 8CH ADC, COMP, QDEC, NFC-A, 4× PWM, nRESET. Usage is limited by number of available GPIO ports. 

- [USB 2.0 full-speed device interface ] 

- [Built-in temperature sensor ] 

- [Angle of arrival (AOA) and angle of ] departure (AOD) direction finding 

## **Characteristics** 

- [Typical sensitivity: -96 dBm at 1 Mb/s ] and -103 dBm at 125 kb/s 

- [Typical max. output power: 8 dBm, configurable ] from -20 dBm in 4 dB steps and -40 dBm in whisper mode 

- [Typical current consumption: 4.9 mA in Tx ] (at 0 dBm) and 4.7 mA in Rx mode 

- [Typical current consumption: 0.6 µA in System ] OFF mode, 1.5 µA with RTC wake up 

- [On-module DC-DC and LDO regulators with ] automated low current modes 

- [Voltage range: 1.7 V to 5.5 V ] 

- [Temperature range: -40 °C to 85 °C ] 

## **Block Diagram** 

Product Specification Rev. 1.0 

Page 2 of 42 

INDUSTRY Panasonic 

- PAN1782 Bluetooth Module 

- > 

## PAN1782 Bluetooth Module 

By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. 

© Panasonic Industrial Devices Europe GmbH 2022. 

This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. 

All rights reserved. 

This Product Specification does not lodge the claim to be complete and free of mistakes. 

If this document is marked as preliminary, please be aware that its final content is not yet concluded and the use of it is at your own risk. 

## **Document Acceptance** 

By signing the Product Specification, you acknowledge that you are a legal representative for your company and that you understand and accept the validity of the contents herein. 

If the signed version of the Product Specification has not been returned to Panasonic within 30 days after receipt of the product, the specification or approval sheet shall be deemed to be accepted by you. 

## **Engineering Samples (ES)** 

If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. 

Engineering Samples are not qualified and they are not to be used for reliability testing or series production. 

## **Disclaimer** 

The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. 

Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by: 

- The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, 

- Deviation or lapse in function of the Engineering Sample, 

- Improper use of the Engineering Sample. 

Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. 

Product Specification Rev. 1.0 

Page 3 of 42 

PAN1782 Bluetooth Module > 

## INDUSTRY Panasonic 

## **Product Change Notifications (PCNs) and Information Notes (INs)** 

Please consider the following PCNs/INs and take suitable countermeasures where necessary and appropriate; for further details please contact your local Panasonic Sales office ( 7.2.1 Contact Us): 

- Nordic APPROTECT vulnerability problem description: IN133 Informational Notice v1.0 

- Nordic APPROTECT solution description: IN149 Informational Notice v1.1 

- The vulnerabilty issue can be fixed by using the PAN1782 module with order number ENW89858A1KF and following the instructions on software given in Nordic APPROTECT solution description: IN149 Informational Notice v1.1 

## **Information on Software** 

The PAN1782 module does not contain any software ex works, i.e. software is provided by 3rd party suppliers only. The essential software resources can be found on the partner website of Nordic Semiconductor https://www.nordicsemi.com/. 

PIDEU provides a factory software programming service for your customized firmware; for further information please reach out to your local sales contact this regarding  7.2.1 Contact Us. 

Product Specification Rev. 1.0 

Page 4 of 42 

- PAN1782 Bluetooth Module 

- > 

## INDUSTRY Panasonic 

## **Table of Contents** 

|**1**|**About This Document ......................................................................................................................... 7**|**About This Document ......................................................................................................................... 7**|
|---|---|---|
||1.1|Purpose and Audience .............................................................................................................. 7|
||1.2|Revision History ......................................................................................................................... 7|
||1.3|Use of Symbols ......................................................................................................................... 7|
||1.4|Related Documents ................................................................................................................... 7|
|**2**|**Overview .............................................................................................................................................. 8**||
||2.1|Block Diagram ........................................................................................................................... 9|
||2.2|Pin Configuration ..................................................................................................................... 10|
||2.3|Peripherals .............................................................................................................................. 12|
||2.4|Bluetooth Features .................................................................................................................. 13|
|**3**|**Detailed Description ......................................................................................................................... 14**||
||3.1|Dimensions .............................................................................................................................. 14|
||3.2|Footprint .................................................................................................................................. 15|
||3.3|Packaging ................................................................................................................................ 16|
||3.4|Case Marking .......................................................................................................................... 19|
|**4**|**Specification ..................................................................................................................................... 20**||
||4.1|Default Test Conditions ........................................................................................................... 20|
||4.2|Absolute Maximum Ratings ..................................................................................................... 20|
||4.3|Recommended Operating Conditions ...................................................................................... 21|
||4.4|Current Consumption............................................................................................................... 21|
||4.5|Bluetooth ................................................................................................................................. 22|
||4.6|Access Port Protection APPROTECT...................................................................................... 22|
||4.7|Antenna Placement Recommendation .................................................................................... 24|
||4.8|Reliability Tests ....................................................................................................................... 26|
||4.9|Recommended Soldering Profile ............................................................................................. 27|
|**5**|**Cautions ............................................................................................................................................ 28**||
||5.1|Design Notes ........................................................................................................................... 28|
||5.2|Installation Notes ..................................................................................................................... 28|
||5.3|Usage Condition Notes ............................................................................................................ 29|
||5.4|Storage Notes .......................................................................................................................... 29|
||5.5|Safety Cautions ....................................................................................................................... 29|
||5.6|Other Cautions ........................................................................................................................ 30|
||5.7|Restricted Use ......................................................................................................................... 31|
|**6**|**Regulatory and Certification Information ....................................................................................... 32**||
||6.1|General Certification Information ............................................................................................. 32|
||6.2|Federal Communications Commission (FCC) for US .............................................................. 33|
||6.3|Innovation, Science, and Economic Development (ISED) for Canada .................................... 35|
||6.4|European Conformity According to RED (2014/53/EU) ........................................................... 38|
||6.5|United Kingdom Conformity According to Statutory Instrument SI 2017/1206......................... 39|
||6.6|Bluetooth ................................................................................................................................. 40|
||6.7|RoHS and REACH Declaration ............................................................................................... 40|



Product Specification Rev. 1.0 

Page 5 of 42 

PAN1782 Bluetooth Module > 

## INDUSTRY Panasonic 

|**7**|**Appendix ........................................................................................................................................... 41**|**Appendix ........................................................................................................................................... 41**|
|---|---|---|
||7.1|Ordering Information ................................................................................................................ 41|
||7.2|Contact Details ........................................................................................................................ 42|



Product Specification Rev. 1.0 

Page 6 of 42 

1 About This Document Panasonic 

- PAN1782 Bluetooth Module 

- > 

## **1 About This Document** 

## **1.1 Purpose and Audience** 

This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1782 module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. 

The product is referred to as “PAN1782” and “module” within this document. 

## **1.2 Revision History** 

|**Revision**|**Date**|**Modifications/Remarks**|
|---|---|---|
|1.0|2022-09-08|First version|



## **1.3 Use of Symbols** 

|**Symbol**|**Description**|
|---|---|
||**Note**<br>Indicates important information for the proper use of the product.<br>Non-observance can lead to errors.|
|A|**Attention**<br>Indicates important notes that, if not observed, can put the product’s functionality<br>at risk.|
|[chapter number]<br>[chapter title]|**Cross reference**<br>Indicates cross references within the document.<br>**Example:**<br>Description of the symbols used in this document1.3 Use of Symbols.|



## **1.4 Related Documents** 

For related documents please refer to the Panasonic website  7.2.2 Product Information. 

Product Specification Rev. 1.0 

Page 7 of 42 

 INDUSTRY PAN1782 Bluetooth Module 2 Overview > Panasonic 

INDUSTRY 2 Overview Panasonic 

## **2 Overview** 

The PAN1782 is a Bluetooth 5.1 Low Energy (LE) module based on the Nordic nRF52833 single chip controller. 

The Bluetooth 5.1 features additionally a higher symbol rate of 2 Mbps using the high speed LE 2M PHY or a significantly longer range using the LE coded PHY at 500 kb/s or 125 kb/s. The new channel selection algorithm (CSA#2) improves the performance in high interference environments. Furthermore, the new LE advertising extensions allow for much larger amounts of data to be broadcasted in connectionless scenarios. 

An output power of up to 8 dBm and the high sensitivity of the nRF52833 in combination with the LE coded PHY make the module very attractive in applications, where a long range is required. 

In addition, the ultra-low current consumption of the PAN1782 makes the module an ideal choice for battery powered devices. 

With the ARM[®] Cortex-M4 processor, 128 kB RAM, and the built-in 512 kB flash memory, the PAN1782 can easily be used in standalone mode, thereby eliminating the need for an external processor, saving complexity, space, and cost. 

The PAN1782 supports angle of arrival (AOA) and angle of departure (AOD) direction finding using Bluetooth. 

The PAN1782 also supports Type 2 Near Field Communication (NFC-A) for use in simplified pairing and payment solutions (external antenna required) 

A 128-bit AES/ECB/CCM/AAR co-processor is included for on-the-fly packet encryption. 

For related documents please refer to  7.2.2 Product Information. 

For further information on the variants and versions please refer to  7.1 Ordering Information. 

Product Specification Rev. 1.0 

Page 8 of 42 

 

2 Overview 

PAN1782 Bluetooth Module 

## **2.1 Block Diagram** 

Product Specification Rev. 1.0 

Page 9 of 42 

**==> picture [187 x 89] intentionally omitted <==**

**----- Start of picture text -----**<br>
<br>PAN1782 Bluetooth Module<br>><br>**----- End of picture text -----**<br>


## PAN1782 Bluetooth Module 

## INDUSTRY 2 Overview Panasonic 

## **2.2 Pin Configuration** 

## **Pin Assignment** 

## Top View 

|F1<br>F2<br>F3<br>F4<br>F5<br>F6<br>F7<br>F8<br>F9<br>F11<br>F12<br>F10<br>OOOOCWOCOCC<br>CO|F1<br>F2<br>F3<br>F4<br>F5<br>F6<br>F7<br>F8<br>F9<br>F11<br>F12<br>F10<br>OOOOCWOCOCC<br>CO|
|---|---|
|E1<br>E2<br>E3<br>E4<br>E5<br>E6<br>E7<br>E8<br>E9<br>OOOOCOCO0O||
|D1<br>D2<br>D3<br>D4<br>D5<br>D6<br>D7<br>D8<br>D9<br>OOOOCOCO0O||
|C1<br>C2<br>C3<br>C4<br>C5<br>C6<br>C7<br>C8<br>C9<br>OOOOCOC0O0O||
|B1<br>B2<br>B3<br>B4<br>B5<br>B6<br>B7<br>B8<br>B9<br>OOOOCOC0O0O||
|A2<br>A3<br>A4<br>A5<br>A6<br>A7<br>A8<br>A9<br>A1<br>HOOOCO0O0C00|A11<br>A12<br>OO|



## **Pin Functions** 

|**No.**|**Pin Name**|**Pin Type**|**Description**|
|---|---|---|---|
|A1|GND|Ground|Connect to ground|
|A2|P0.30/AIN6|Digital BI/Analog Input|GPIO/Analogue signal to ADC/COMP|
|A3|P0.18/nRESET|Digital BI|GPIO/Low active RESET|
|A4|NC|NC|Do not connect|
|A5|VCC|Power|Connect 1.7 V to 3.6 V in Normal Voltage Mode|
||||Leave open in High Voltage Mode|
|A6|VDDH|Power|Connect to VCC(1.7 V to 3.6 V) in Normal Voltage Mode|
||||Connect 2.5 V to 5.5 V in High Voltage Mode|
|A7|GND|Ground|Connect to ground|
|A8|P0.09/NFC1|Digital BI/RF NFC BI|GPIO/Connect to NFC Antenna|
|A9|GND|Ground|Connect to ground|
|A11|GND|Ground|Connect to ground, necessary for antenna to stay tuned|
|A12|GND|Ground|Connect to ground, necessary for antenna to stay tuned|
|B1|P0.02/AIN0|Digital BI|GPIO/Analogue signal to ADC/COMP|
|B2|P0.04/AIN2|Digital BI/Analog Input|GPIO/Analogue signal to ADC/COMP|



Product Specification Rev. 1.0 

Page 10 of 42 

##  INDUSTRY PAN1782 Bluetooth Module 2 Overview > Panasonic 

## INDUSTRY 2 Overview Panasonic 

|**No.**|**Pin Name**|**Pin Type**|**Description**|
|---|---|---|---|
|B3|NC|NC|Do not connect|
|B4|NC|NC|Do not connect|
|B5|P0.28/AIN4<br>UART_RTS|Digital BI|GPIO or UART_RTS or Analogue signal to ADC/COM|
|B6|P0.11<br>UART_CTS|Digital BI|GPIO or UART_CTS|
|B7|NC|NC|Do not connect|
|B8|NC|NC|Do not connect|
|B9|NC|NC|Do not connect|
|C1|NC|NC|Do not connect|
|C2|NC|NC|Do not connect|
|C3|P0.05/AIN3|Digital BI|GPIO/Analogue signal to ADC/COMP|
|C4|SWDIO|Digital BI|Serial Wire Data I/O|
|C5|SWDCLK|Digital IN|Serial Wire Data Clock|
|C6|P0.17|Digital BI|GPIO|
|C7|NC|NC|Do not connect|
|C8|GND|Ground|Connect to ground|
|C9|GND|Ground|Connect to ground|
|D1|NC|NC|Do not connect|
|D2|NC|NC|Do not connect|
|D3|NC|NC|Do not connect|
|D4|NC|NC|Do not connect|
|D5|NC|NC|Do not connect|
|D6|NC|NC|Do not connect|
|D7|GND|Ground|Connect to ground|
|D8|GND|Ground|Connect to ground|
|D9|GND|Ground|Connect to ground|
|E1|P0.15|Digital BI|GPIO|
|E2|P0.20|Digital BI|GPIO|
|E3|VBUS|Power|USB-Bus Supply Voltage|
||||Connect if USB is used|
|E4|NC|NC|Do not connect|
|E5|NC|NC|Do not connect|



Product Specification Rev. 1.0 

Page 11 of 42 

##  INDUSTRY PAN1782 Bluetooth Module 2 Overview > Panasonic 

## INDUSTRY 2 Overview Panasonic 

|**No.**|**Pin Name**|**Pin Type**|**Description**|
|---|---|---|---|
|E6|P0.03/AIN1<br>UART_RXD|Digital BI|GPIO or UART_RXD or Analogue signal to ADC/COM|
|E7|NC|NC|Do not connect|
|E8|GND|Ground|Connect to ground|
|E9|GND|Ground|Connect to ground|
|F1|GND|Ground|Connect to ground|
|F2|NC|NC|Do not connect|
|F3|DP|Digital BI|USB differential line with polarity +|
|F4|DM|Digital BI|USB differential line with polarity -|
|F5|P0.31/AIN7|Digital BI/Analog Input|GPIO/Analogue signal to ADC/COMP|
|F6|P0.10/NFC2|Digital BI/RF NFC BI|GPIO/Connect NFC Antenna|
|F7|P1.09<br>UART_TXD|Digital BI|GPIO or UART_TXD|
|F8|P0.29/AIN5|Digital BI|GPIO/Analogue signal to ADC/COMP|
|F9|GND|Ground|Connect to ground|
|F10|NC|NC|Do not connect|
|F11|GND|Ground|Connect to ground, necessary for antenna to stay tuned|
|F12|GND|Ground|Connect to ground, necessary for antenna to stay tuned|



## **2.3 Peripherals** 

- Full speed USB 2.0 device controller 

- 2× UART (2 or 4 wire with CTS/RTS, 1 200 up to 1 M baud) 

- 2× I[2] C (100 kHz or 400 kHz) 

- 4× SPI master/3× SPI slave (125 kbps up to 8 Mbps) 

- 8× 12-bit, 200 ksps ADC 

- Audio I[2] S digital microphone interface 

- PWM 4× 32-bit timer 

- AES CCM mode encryption on-the-fly 

- 4-channel comparator 

- Quadrature decoder QDEC 

- Temperature sensor 

- 3× Real-time counter RTC 

- Watchdog timer 

- 16 PIOs including RESET, 4-wire UART 

- Integrated 32 kHz crystal 

- Serial wire debug and program interface 

Product Specification Rev. 1.0 

Page 12 of 42 

 PAN1782 Bluetooth Module • • •[>] 

## INDUSTRY 2 Overview Panasonic 

## **2.4 Bluetooth Features** 

- Bluetooth 5.1 LE 

- Supports Bluetooth 5.1 LE high speed and long-range modes 

- AOA and AOD direction finding 

Product Specification Rev. 1.0 

Page 13 of 42 

PAN1782 Bluetooth Module 

3 Detailed Description 

 

## **3 Detailed Description** 

## **3.1 Dimensions** 

**==> picture [307 x 410] intentionally omitted <==**

**----- Start of picture text -----**<br>
The dimensions are in millimeters.<br>Top View<br>——<br>be 0<br>15.60<br>2.00<br>1.20<br>8.70<br>**----- End of picture text -----**<br>


|**Item**|**Dimension**|**Tolerance**|**Remark**|
|---|---|---|---|
|Width|8.70|±0.30|±0.30|
|Length|15.60|±0.30|±0.30|
|Height|2.00|±0.20 With case|±0.20 With case|



Product Specification Rev. 1.0 

Page 14 of 42 

 PAN1782 Bluetooth Module > 

INDUSTRY 3 Detailed Description Panasonic 

## **3.2 Footprint** 

The dimensions are in millimeters. 

## Top View 

**==> picture [381 x 245] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
|3.00|
|F1|F2|F3|F4|F5|F6|F7|F8|F9|F10|F11|F12|
|eeoeecceccoee|
|E1|E2|E3|E4|E5|E6|E7|E8|E9|
|CO0000000|
|D1|D2|D3|D4|D5|D6|D7|D8|D9|
|000000000||...|
|C1|C2|C3|C4|C5|C6|C7|C8|C9|
|000000000||\~"™|
|B1|B2|B3|B4|B5|B6|B7|B8|B9|
|CO0000000|
|A1|A2|A3|A4|A5|A6|A7|A8|A9|A11|A12|
|Pee|orReoees|OO|
|1.00|1.20|_|0.60|2.40|
|5.00|
|15.60|

**----- End of picture text -----**<br>


Product Specification Rev. 1.0 

Page 15 of 42 

> 3 Detailed Description Panasonic 

**==> picture [195 x 89] intentionally omitted <==**

**----- Start of picture text -----**<br>
<br>PAN1782 Bluetooth Module<br>><br>**----- End of picture text -----**<br>


## **3.3 Packaging** 

The module is a mass production status product and will be delivered in the package described below. 

## **3.3.1 Tape Dimensions** 

## **3.3.2 Packing in Tape** 

## Direction of unreeling (for customer) 

trailer (empty) component leader (empty) Top cover tape more 1 x circumference / packed area minimum 10 pitch than 1 x circumference plus hub standard 100mm to avoid (min 160mm) 1500pcs fixing of tape end on sealed modules. 

Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive. 

The top cover tape shall not be found on reel holes and it shall not stick out from the reel. 

Product Specification Rev. 1.0 

Page 16 of 42 

##  ~~,~~ PAN1782 Bluetooth Module 3 Detailed Description **3.3.3 Component Direction** 

**==> picture [357 x 196] intentionally omitted <==**

**----- Start of picture text -----**<br>
Pin 1 Marking<br>(Top Side)<br>Direction of<br>unreeling<br>(for customer)<br>_. x<br> SS SS(- (<A  : ©  E<br>**----- End of picture text -----**<br>


## **3.3.4 Reel Dimension** 

Product Specification Rev. 1.0 

Page 17 of 42 

 > PAN1782 Bluetooth Module 

INDUSTRY 3 Detailed Description Panasonic 

## **3.3.5 Package Label** 

## **Example:** 

(1T) Lot code (1P) Customer order number, if applicable (2P) Order number (9D) Date code (Q) Quantity (HW/SW) Hardware/software version 

## **3.3.6 Total Package** 

Product Specification Rev. 1.0 

Page 18 of 42 

- 

- > PAN1782 Bluetooth Module 

## 3 Detailed Description Panasonic 

## **3.4 Case Marking** 

## **Example:** 

- 1 Brand name 

- 2 Hardware/software version 

- 3 Order number 

- 4 Lot code 

- 5 Status: ES or empty for MP 

- 6 2D barcode, for internal usage only 

- 7 Marking for Pin 1 

- 8 Bluetooth logo 

Product Specification Rev. 1.0 

Page 19 of 42 

 

4 Specification 

PAN1782 Bluetooth Module 

## **4 Specification** 

**==> picture [30 x 30] intentionally omitted <==**

**----- Start of picture text -----**<br>
©<br>**----- End of picture text -----**<br>


All specifications are over temperature and process, unless indicated otherwise. 

## **4.1 Default Test Conditions** 

**==> picture [30 x 30] intentionally omitted <==**

**----- Start of picture text -----**<br>
©<br>**----- End of picture text -----**<br>


Temperature: 25 °C ± 10 °C Humidity: 40 % to 85 % RH Supply Voltage: 3.3 V 

## **4.2 Absolute Maximum Ratings** 

The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. 

|**Symbol**|**Parameter**|**Condition**|**Min.**|**Typ. **|**Max.**|**Unit**|
|---|---|---|---|---|---|---|
|VDD|Normal SupplyVoltage||-0.3|-0.3|3.9|V|
|VDDH|High Supply Voltage||-0.3|-0.3|5.8||
|VBUS|USB Bus Voltage||-0.3|-0.3|5.8||
|I/O Pin|Voltage on any Pin|VDD≤ 3.6 V|-0.3|-0.3|VDD+ 0.3||
|||VDD> 3.6 V|-0.3|-0.3|3.9||
|ESD|ESD Robustness|HBM 2|||±2 000||
|||CDM|||500||
|MSL|Moisture SensitivityLevel|Level|||3||
|PRF|RF Input Level||||10|dBm|
|TSTOR|Storage Temperature||-40|-40|125|°C|



Product Specification Rev. 1.0 

Page 20 of 42 

 PAN1782 Bluetooth Module > 

## Panasonic 4 Specification 

## **4.3 Recommended Operating Conditions** 

The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. 

|**Symbol**|**Parameter**|**Condition**|**Min.**|**Typ. **|**Max.**|**Unit**|
|---|---|---|---|---|---|---|
|VDD(LV Mode)|SupplyVoltage||1.7||3.6|V|
|tR_ VDD|Supply Rise<br>Time|0 V to 1.7 V|||60|ms|
|VDD-POR|SupplyVoltage|Power on Reset active|1.75|||V|
|VDDH (HV Mode)|SupplyVoltage|VDDH (optional)|2.5||5.5|V|
|tR_VDDH|Supply Rise<br>Time|0 V to 3.7 V|||100|ms|
|VBUS|VBUS USB<br>SupplyVoltage|VBUS(optional)|4.35||5.5|V|
|VI/O|Max I/O Pin<br>Voltage|VDD≤ 3.6 V|-0.3||VDD+ 0.3|V|
|||VDD≥ 3.6 V|||3.9||
|TA|Operating<br>Temperature||-40|25|85|°C|



## **4.4 Current Consumption** 

The current consumption depends on the user scenario and on the setup and timing in the power modes. 

Assume VDD = 3 V, Tamb = 25 °C, if nothing else stated, DC/DC enabled. 

|**Parameter**|**Condition**|**Min.**|**Typ. **|**Max.**|**Unit**|
|---|---|---|---|---|---|
|Sleep Mode|No RAM retention, Wake on Reset, SYS OFF||0.6|0.6|µA|
||Full RAM retention, Wake on Reset, SYS OFF||1.3|1.3|µA|
||No RAM retention, Wake on any event,<br>SYS ON||1.1|1.1|µA|
||Full RAM retention, Wake on any event,<br>SYS ON||1.8|1.8|µA|
||No RAM retention, Wake on RTC, SYS ON||1.5|1.5|µA|
|CPU executing<br>CoreMark|Runningfrom RAM, DC/DC ON, HFXO||2.4|2.4|mA|
||Runningfrom Flash DC/DC ON, HFXO||3.3|3.3|mA|
|Rx Current|Rx only 1 Mbps Bluetooth LE Mode,<br>DC/DC ON, HFXO||4.6|4.6|mA|



Product Specification Rev. 1.0 

Page 21 of 42 

##  INDUSTRY > PAN1782 Bluetooth Module Panasonic 4 Specification 

## INDUSTRY Panasonic 4 Specification 

|**Parameter**|**Condition**|**Min.**|**Typ. **|**Max.**|**Unit**|
|---|---|---|---|---|---|
|Tx Current|8 dBm Tx only, DC/DC ON||14.2||mA|
||4 dBm Tx only, DC/DC ON||9.6||mA|
||0 dBm Tx only, DC/DC ON||4.9||mA|
||-4 dBm Tx only, DC/DC ON||3.8||mA|
||-8 dBm Tx only, DC/DC ON||3.4||mA|
||-12 dBm Tx only, DC/DC ON||3.1||mA|
||-16 dBm Tx only, DC/DC ON||2.9||mA|
||-20 dBm Tx only, DC/DC ON||2.7||mA|
||-40 dBm Tx only, DC/DC ON||2.3||mA|



## **4.5 Bluetooth** 

|**Parameter**|**Specification**|
|---|---|
|Frequency|2 402 MHz to 2 480 MHz|
|Data Rate|2 Mbps, 1 Mbps, 500 kbps, 125 kbps|
|Number of Channels|40: 37 data/3 advertising (0, 12, 39)|
|Receive Sensitivity|-103 dBm (125 kbps Bluetooth LE Mode), -96 dBm (1 Mbps Bluetooth<br>LE Mode), -92dBm (2 Mbps Bluetooth LE Mode)|
|Output Power|-40 dBm to +8 dBm|
|Link Budget|Up to 111 dB|



## **4.6 Access Port Protection APPROTECT** 

The PAN1782 with order number ENW89858A1KF supports the APPROTECT feature. A special sequence of commands is necessary during production programming. These commands ensure that the built-in Bluetooth Device Address is preserved when the access port protection is enabled. 

The access port protection prevents (amongst others) any access to the built-in flash memory through the device debug port. 

In factory state, the PAN1782 with order number ENW89858A1KF implementing Nordic nRF52833 “revision 2 silicon” comes with the access port protection disabled. 

Product Specification Rev. 1.0 

Page 22 of 42 

- PAN1782 Bluetooth Module 

- > 

## Panasonic 4 Specification 

## PAN1782 Bluetooth Module 4 Specification 

## **Locking the Device Debug Port and enabling the Access Port Protection** 

Once the access port protection is enabled, no further access including debugging can be done anymore! 

To ensure that the device debug port is locked during production programming and the access port protection is enabled correctly, the following steps must be followed. 

1. Use the Microcontroller Development Kit (MDK) nRF MDK (version 8.40.2) or later for application development. 

   - If the application is based on nRF5 SDK (version 17.1.0) or later version, compile the application with the globally defined `ENABLE_APPROTECT` -define. Open the project in **Segger Embedded Studio** . Set the define in **Project** 

**options** > Section **Code** > **Preprocessor Options** > **Preprocessor Definitions** . 

   - If the application is based on nRF Connect SDK (version 1.8.0) or later version, compile the application with the option set `CONFIG_NRF_APPROTECT_LOCK=y` , for example in the project configuration file `prj.conf` . 

2. Use the nRF Command Line Tools (version 10.15.4) for production programming. Please make sure to use version 10.15.4 or later. 

3. Execute `nrfjprog.exe --verify fast --sectorerase --program` 

`application.hex` from a command line prompt to program an application HEX file: 

`Parsing image file. Verifying programming. Verified OK.` 

4. Execute `nrfjprog.exe --rbp ALL` from a command line prompt to enable the access port protection: 

`Protected the device against read and debug. Only a --recover, --debugreset, or --pinreset operations will work from now on.` 

It is possible to disable the access port protection again using the option `recover` , but the complete PAN1782 module is erased including the built-in Bluetooth Device Address. For details how to prevent this during application development, please refer to the “PAN1782 EVB User Guide (“Bluetooth Address Safeguard”)”. 

For technical details please refer to IN149 Informational Notice v1.1 in the Nordic Infocenter https://infocenter.nordicsemi.com/. 

Product Specification Rev. 1.0 

Page 23 of 42 

4 Specification 

##  

PAN1782 Bluetooth Module 

## **4.7 Antenna Placement Recommendation** 

## **Antenna “Keep out Area”** 

Do not place any ground plane under the marked restricted antenna area in any layer! This would be affecting the performance of the chip antenna in a critical manner. 

## **Impact of Placement on the Antenna Radiation Pattern** 

The placement of the module, surrounding material, and customer components has an impact on the radiation pattern of the antenna. 

The recommendation for the ground plane is based on a FR4 4-Layer PCB. 

The following requirements must be met: 

- ✓ The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 µF directly at the module). 

- ✓ This module should not be mechanically stressed when installed. 

- ✓ Keep this module away from heat. Heat is the major cause of decreasing the life time of these modules. 

- ✓ Avoid assembly and use of the target equipment in conditions where the module temperature may exceed the maximum tolerance. 

- ✓ Keep this module away from other high frequency circuits. 

- ✓ Refer to the recommended pattern when designing a board. 

The antenna requires a cutout area of 5 mm × 3 mm under the PAN1782 module. This “Keep out Area” shall be located in every layer under the module antenna. 

It is recommended to verify the perfect position of the module in the target application before fixing the design. 

Product Specification Rev. 1.0 

Page 24 of 42 

- PAN1782 Bluetooth Module 

- > 

##  PAN1782 Bluetooth Module Panasonic 4 Specification 

## **Antenna Placement Recommendation** 

All dimensions are in millimeters. 

Use a ground plane in the area surrounding the module wherever possible. Use stitching vias to GND left and right from the “Keep out Area” and on the PCB edges 

It is recommended to place the module: 

- At the PCB edge (horizontal) of mother PCB with the module antenna at the PCB edge 

- GND plane on the left and right of the module 

## Top View 

**==> picture [286 x 208] intentionally omitted <==**

**----- Start of picture text -----**<br>
Min. 15.00 8.70 Min. 15.00<br>5.00<br>Keep out<br>Area<br>Top View<br>| i<br>3.00<br>15.60<br>Min. 40.00<br>**----- End of picture text -----**<br>


Product Specification Rev. 1.0 

Page 25 of 42 

 INDUSTRY > PAN1782 Bluetooth Module Panasonic 4 Specification 

INDUSTRY Panasonic 4 Specification 

## **4.8 Reliability Tests** 

The measurement should be done after the test module has been exposed to room temperature and humidity for one hour. 

|**No.**|**Item**|**Limit**|**Condition**|
|---|---|---|---|
|1 Variable Vibration Test Electrical parameters should be|1 Variable Vibration Test Electrical parameters should be|1 Variable Vibration Test Electrical parameters should be<br>within specification|Freq.: 20 Hz~2 000 Hz, Acc.: 17 G to<br>50 G, Sweep: 8 min, 2 hours, For: XYZ<br>axis|
|2 Shock Drop Test|2 Shock Drop Test||Drop parts on concrete from a height of<br>1 m for 3 times|
|3 Heat-Shock/|3 Heat-Shock/<br>Temperature Cycling<br>Test||At -40 °C and 85 °C for 1 h/cycle<br>Total = 300 cycles|
|4 Temperature Humidity|4 Temperature Humidity<br>Bias Test||At 60 °C, 85 % r. H., 300 h|
|5 Low Temperature|5 Low Temperature<br>Storage Life Test||At -40 °C, 300 h|
|6 High Temperature|6 High Temperature<br>Storage Life Test||At 85 °C, 300 h|



Product Specification Rev. 1.0 

Page 26 of 42 

 

4 Specification 

PAN1782 Bluetooth Module 

## **4.9 Recommended Soldering Profile** 

- Reflow permissible cycles: 2 

- Opposite side reflow is prohibited due to module weight 

- More than 75 percent of the soldering area shall be coated by solder 

- • The soldering profiles should be adhered to in order to prevent electrical or mechanical damage 

- Soldering profile assumes lead-free soldering 

Product Specification Rev. 1.0 

Page 27 of 42 

INDUSTRY 5 Cautions Panasonic 

 PAN1782 Bluetooth Module > 

## **5 Cautions** 

Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module. 

## **5.1 Design Notes** 

1. Follow the conditions written in this specification, especially the control signals of this module. 

2. The supply voltage should abide by the maximum ratings ( 4.2 Absolute Maximum Ratings). 

3. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 µF directly at the module). 

4. This module should not be mechanically stressed when installed. 

5. Keep this module away from heat. Heat is the major cause of decreasing the life time of these modules. 

6. Avoid assembly and use of the target equipment in conditions where the module temperature may exceed the maximum tolerance. 

7. Keep this module away from other high frequency circuits. 

8. Refer to the recommended pattern when designing a board. 

## **5.2 Installation Notes** 

1. Reflow soldering is possible twice based on the conditions set forth in  4.9 Recommended Soldering Profile. Set up the temperature at the soldering portion of this module according to this reflow profile. 

2. Carefully position the module so that the heat will not burn into printed circuit boards or affect other components that are susceptible to heat. 

3. Carefully locate the module, to avoid an increased temperature caused by heat generated by neighboring components. 

4. If a vinyl-covered wire comes into contact with the module, the wire cover will melt and generate toxic gas, damaging the insulation. Never allow contact between a vinyl cover and these modules to occur. 

5. This module should not be mechanically stressed or vibrated when reflowed. 

6. To repair the board by hand soldering, follow the conditions set forth in this chapter. 

7. Do not wash this product. 

8. Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the module. 

Product Specification Rev. 1.0 

Page 28 of 42 

INDUSTRY 5 Cautions Panasonic 

PAN1782 Bluetooth Module 5 Cautions 

- PAN1782 Bluetooth Module 

- > 

## **5.3 Usage Condition Notes** 

1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 

2. Do not use dropped modules. 

3. Do not touch, damage, or soil the pins. 

4. Follow the recommended condition ratings about the power supply applied to this module. 

5. Electrode peeling strength: Do not apply a force of more than 4.9 N in any direction on the soldered module. 

6. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. 

7. These modules are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information, and communication equipment. 

## **5.4 Storage Notes** 

1. The module should not be stressed mechanically during storage. 

2. Do not store these modules in the following conditions or the performance characteristics of the module, such as RF performance will be adversely affected: 

   - Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX, 

   - Storage in direct sunlight, 

   - Storage in an environment where the temperature may be outside the range of 5 °C to 35 °C, or where the humidity may be outside the 45 % to 85 % range, 

   - Storage of the modules for more than one year after the date of delivery storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. 

3. Keep this module away from water, poisonous gas, and corrosive gas. 

4. This module should not be stressed or shocked when transported. 

5. Follow the specification when stacking packed crates (max. 10). 

## **5.5 Safety Cautions** 

These specifications are intended to preserve the quality assurance of products and individual components. 

Before use, check and evaluate the operation when mounted on your products. Abide by these specifications without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, provide the following failsafe functions as a minimum: 

Product Specification Rev. 1.0 

Page 29 of 42 

 INDUSTRY PAN1782 Bluetooth Module 5 Cautions > Panasonic 

INDUSTRY 5 Cautions Panasonic 

1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 

2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 

## **5.6 Other Cautions** 

1. Do not use the module for other purposes than those listed in section  5.3 Usage Condition Notes. 

2. Be sure to provide an appropriate fail-safe function on your product to prevent any additional damage that may be caused by the abnormal function or the failure of the module. 

3. This module has been manufactured without any ozone chemical controlled under the Montreal Protocol. 

4. These modules are not intended for use under the special conditions shown below. Before using these modules under such special conditions, carefully check their performance and reliability under the said special conditions to determine whether or not they can be used in such a manner: 

   - In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash, 

   - In direct sunlight, outdoors, or in a dusty environment, 

   - In an environment where condensation occurs, 

   - In an environment with a high concentration of harmful gas (e. g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX). 

5. If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these modules with new modules, because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. 

For further information please refer to the Panasonic website  7.2.2 Product Information. 

Product Specification Rev. 1.0 

Page 30 of 42 

 PAN1782 Bluetooth Module > 

INDUSTRY 5 Cautions Panasonic 

## **5.7 Restricted Use** 

## **5.7.1 Life Support Policy** 

This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 

Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. 

## **5.7.2 Restricted End Use** 

This Panasonic Industrial Devices Europe GmbH product is not designed for any restricted activity that supports the development, production, handling usage, maintenance, storage, inventory or proliferation of any weapons or military use. 

Transfer, export, re-export, usage or reselling of this product to any destination, end user or any end use prohibited by the European Union, United States or any other applicable law is strictly prohibited. 

Product Specification Rev. 1.0 

Page 31 of 42 

 

6 Regulatory and Certification Information 

PAN1782 Bluetooth Module 

## **6 Regulatory and Certification Information** 

## **6.1 General Certification Information** 

Regulatory certifications are valid for the following radio relevant software: 

- Nordic SoftDevices S113 and S140 

- Bluetooth Specification 5.1 

Regulatory certifications stay valid for APPROTECT versions provided that: 

If the nRF52833 new silicon revision 2 with access port protection, which is implemented in the PAN1782 with Panasonic order number ENW89858A1KF is used: 

- Nordic IN149 Informational Notice v1.1 states “The new revision has no impact on CE, FCC/ISED or Bluetooth certifications unless the new pulse shaping filter is enabled.” 

- Nordic FTPAN-254 describes how to enable the pulse shaping filter, but as stated before it needs to remain disabled. Hence the code described in Nordic FTPAN-254 shall not be implemented/executed; otherwise the PAN1782 pre-certification becomes invalid. The Nordic FTPAN-254 workaround is meant for designs using an PA/LNA RF front end, which is not feasible with the PAN1782. Therefore, it is not useful to implement Nordic FTPAN-254. 

For further certification requests for other radio software please contact Panasonic  7.2 Contact Details. 

Product Specification Rev. 1.0 

Page 32 of 42 

6 Regulatory and Certification Information 

##  

PAN1782 Bluetooth Module 

## **6.2 Federal Communications Commission (FCC) for US** 

## **6.2.1 FCC Notice** 

**==> picture [31 x 30] intentionally omitted <==**

**----- Start of picture text -----**<br>
©<br>**----- End of picture text -----**<br>


The PAN1782 including the antennas, which are listed in  6.2.5 Approved Antenna List, complies with Part 15 of the FCC Rules. 

The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 

1. This device may not cause harmful interference, and 

2. This device must accept any interference received, including interference that may cause undesired operation. 

## **6.2.2 Caution** 

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 

There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

- Reorient or relocate the receiving antenna, 

- Increase the separation between the equipment and receiver, 

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, 

- Consult the dealer or an experienced radio/TV technician for help. 

Product Specification Rev. 1.0 

Page 33 of 42 

6 Regulatory and Certification Information 

PAN1782 Bluetooth Module 

- PAN1782 Bluetooth Module 

- > 

## INDUSTRY Panasonic 

## **6.2.3 Label Requirements** 

The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. 

The FCC identifier is **FCC ID: T7V1782** 

This FCC identifier is valid for the PAN1782. The end product must in any case be labelled on the exterior with: 

"Contains FCC ID: T7V1782". 

Due to the PAN1782 model size, the FCC identifier is displayed on the product package and in the installation instruction only. It cannot be displayed readable on the module’s label due to the limited size. 

## **6.2.4 Antenna Warning** 

This antenna warning refers to the test device with the model number PAN1782  7.1 Ordering Information.Ordering Information 

The device is tested with a standard SMA connector and with the antenna listed below. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions. The FCC identifier for the device with the antenna listed in  6.2.5 Approved Antenna List is the same ( **FCC ID: T7V1782** ). 

## **6.2.5 Approved Antenna List** 

|**Item**|**Part Number**|**Manufacturer**|**Frequency Band**<br>**(GHz)**|**Type**|**Max. Gain**<br>**(dBi)**|
|---|---|---|---|---|---|
|1 ANT016008LCS2442MA1 TDK|1 ANT016008LCS2442MA1 TDK|1 ANT016008LCS2442MA1 TDK|2.4 Chi|2.4 Chipantenna|+1|



Product Specification Rev. 1.0 

Page 34 of 42 

 PAN1782 Bluetooth Module > 

INDUSTRY Panasonic 

6 Regulatory and Certification Information 

## **6.2.6 RF Exposure** 

To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed  6.2.5 Approved Antenna List. 

The preceding statement must be included as a “CAUTION” statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. 

Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. 

The radiated output power of the PAN1782 with a mounted ceramic antenna ( **FCC ID: T7V1782** ) is below the FCC radio frequency exposure limits. Nevertheless, the PAN1782 shall be used in such a manner that the potential for human contact during normal operation is minimized. 

End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. 

## **6.3 Innovation, Science, and Economic Development (ISED) for Canada** 

## **English** 

The PAN1782 is licensed to meet the regulatory requirements of ISED. 

License ID: **IC: 216Q-1782** 

HVIN: **ENW89858A1KF** 

Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. 

This device has been designed to operate with the antennas listed in  6.2.5 Approved Antenna List, having a maximum gain of +1 dBi. Antennas not included in this list or having a gain greater than +1 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

Due to the model size, the IC identifier is displayed in the installation instruction only and it cannot be displayed on the module’s label due to the limited size. 

Product Specification Rev. 1.0 

Page 35 of 42 

- PAN1782 Bluetooth Module 

- > 

## PAN1782 Bluetooth Module 

## Panasonic 

## 6 Regulatory and Certification Information 

The end customer has to assure that the device has a distance of more than 15 mm from the human body under all circumstances. 

If the end customer application intends to use the PAN1782 in a distance smaller 15 mm from the human body, SAR evaluation has to be repeated by the OEM. 

The end customer equipment must meet the actual Safety/Health requirements according to ISED. 

## **French** 

PAN1782 est garanti conforme aux dispositions règlementaires d’Industry Canada (ISED). 

License: **IC: 216Q-1782** HVIN: **ENW89858A1KF** 

Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique maximum autorisé. 

Des informations pour les utilisateurs sur la réglementation Canadienne concernant l’exposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. 

Ce produit a été développé pour fonctionner spécifiquement avec les antennes listées dans le tableau  6.2.5 Approved Antenna List, présentant un gain maximum de +1 dBi. Des antennes autres que celles listées ici, ou présentant un gain supérieur à +1 dBi ne doivent en aucune circonstance être utilisées en combinaison avec ce produit. L’impédance des antennes compatibles est 50 Ohm. L’antenne utilisée avec ce produit ne doit ni être située à proximité d’une autre antenne ou d’un autre émetteur, ni être utilisée conjointement avec une autre antenne ou un autre émetteur. 

En raison de la taille du produit, l’identifiant IC est fourni dans le manuel d’installation. 

Le client final doit s'assurer que l'appareil se trouve en toutes circonstances à une distance de plus de 15 mm du corps humain. 

Si le client final envisage une application nécessitant d'utiliser le PAN1782 à une distance inférieure à 15 mm du corps humain, alors le FEO doit répéter l'évaluation DAS. 

L'équipement du client final doit répondre aux exigences actuelles de sécurité et de santé selon l’ISED. 

Product Specification Rev. 1.0 

Page 36 of 42 

 

6 Regulatory and Certification Information 

PAN1782 Bluetooth Module 

## **6.3.1 IC Notice** 

## **English** 

**==> picture [30 x 30] intentionally omitted <==**

**----- Start of picture text -----**<br>
©<br>**----- End of picture text -----**<br>


The device PAN1782 ( 7.1 Ordering Information), including the antennas ( 6.2.5 Approved Antenna List), complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. 

Operation is subject to the following two conditions: 

1. This device may not cause harmful interference, and 

2. This device must accept any interference received, including interference that may cause undesired operation. 

## **French** 

© 

Le présent appareil PAN1782 ( 7.1 Ordering Information), les antennes y compris ( 6.2.5 Approved Antenna List), est conforme aux CNR-Gen d'Industrie Canada applicables aux appareils radio exempts de licence. 

L'exploitation est autorisée aux deux conditions suivantes: 

1. L'appareil ne doit pas produire de brouillage, et 

2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 

## **6.3.2 Labeling Requirements** 

## **English** 

**==> picture [30 x 30] intentionally omitted <==**

**----- Start of picture text -----**<br>
©<br>**----- End of picture text -----**<br>


## **Labeling Requirements** 

The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. 

The IC identifier is **IC: 216Q-1782** 

This IC identifier is valid for all PAN1782 modules  7.1 Ordering Information. In any case, the end product must be labelled on the exterior with: 

"Contains IC: 216Q-1782”. 

Product Specification Rev. 1.0 

Page 37 of 42 

 PAN1782 Bluetooth Module > 

## Panasonic 

6 Regulatory and Certification Information 

## **French** 

**==> picture [30 x 29] intentionally omitted <==**

**----- Start of picture text -----**<br>
@<br>**----- End of picture text -----**<br>


**Obligations d’étiquetage** Les fabricants d’équipements d’origine (FEO) – en anglais Original Equipment Manufacturer (OEM) – doivent s’assurer que les obligations d’étiquetage IC du produit final sont remplies. Ces obligations incluent une étiquette clairement visible à l’extérieur de l’emballage externe, comportant l’identifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. 

## L’ identifiant IC est **IC: 216Q-1782** 

Cet identifiant est valide pour tous les modules PAN1782  7.1 Ordering Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante: 

"Contient IC: 216Q-1782”. 

## **6.4 European Conformity According to RED (2014/53/EU)** 

All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 

3.1a Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017/AC:2017 EN 62479: 2010 

3.1b EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.4: (2020-09) 

3.2 Radio: EN 300 328 V2.2.2: (2019-07) 

- Due to the model size, the CE marking is displayed on the product package and in the installation instruction only. It cannot be displayed conform to regulation (EU) No. 765/2008 in 5 mm height on the module’s label due to the limited space. 

- The RED EU Type Examination Certificate No. **T818987P-01** issued by the Notified Body 0682 can be used for the OEM end product conformity assessment. If a Notified Body has been contracted for the end product conformity assessment, it should be noted that this EU Type Examination Certificate should be used for conformance assessment. 

As a result of the conformity assessment procedure described in 2014/53/EU Directive, the end customer equipment should be labelled as follows: 

Product Specification Rev. 1.0 

Page 38 of 42 

 PAN1782 Bluetooth Module > 

6 Regulatory and Certification Information 

## INDUSTRY Panasonic 

The requirements for CE marking are described in regulation (EC) No. 765/2008 Annex II. 

The end customer has to assure that the device has a distance of more than 5 mm from the human body under all circumstances. 

If the end customer application intends to use the PAN1782 in a distance smaller 5 mm from the human body, SAR evaluation has to be repeated by the OEM. 

The end customer equipment must meet the actual Safety/Health requirements according to RED. 

PAN1782 and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra, and Turkey. 

## **6.5 United Kingdom Conformity According to Statutory Instrument SI 2017/1206** 

All modules described in this Product Specification comply with the designated standards according to the following Regulations: Electrical Equipment (Safety) SI 2016/1101, EMC SI 2016/1091 together with Radio Equipment Regulation 2017 (RER) SI 2017/1206: 

Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 

EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) Radio: EN 300 328 V2.2.2: (2019-07) 

- Due to the model size, the UK marking is displayed in the installation instruction only and it cannot be displayed conform to SI 2017/1206 on the module’s label due to the limited space. 

- The RED EU Type Examination Certificate No. **T818987P-01** issued by the EU Notified Body 0682 can be used for the OEM end product conformity assessment. If a Notified Body has been contracted for the end product conformity assessment, it should be noted that this EU Type Examination Certificate should be used for conformance assessment. 

As a result of the conformity assessment procedure described in SI 2017/1206 Directive, the end customer equipment should be labelled as follows: 

cA 

Product Specification Rev. 1.0 

Page 39 of 42 

 

6 Regulatory and Certification Information 

PAN1782 Bluetooth Module 

## **Restrictions or Requirements in the UK** 

The end customer has to assure that the device has a distance of more than 5 mm from the human body under all circumstances. 

If the end customer application intends to use the PAN1782 in a distance smaller 5 mm from the human body, SAR evaluation has to be repeated by the OEM. 

The end customer equipment must meet the actual Safety/Health requirements according to SI 2017/1206. 

PAN1782 and its model versions in the specified reference design can be used in the UK. 

## **6.6 Bluetooth** 

The final Bluetooth end product listing needs to be created by using the following IDs: 

|**Bluetooth 5.1**|**Declaration ID**|**QDID**|
|---|---|---|
|End Product (PAN1782 Bluetooth LE<br>LR Module)|D058507|187324|



## **Bluetooth Marks** 

According to the Bluetooth SIG, the PAN1782 fulfills the criteria to label your product as a Bluetooth device: 

For further information please refer to the Bluetooth website www.bluetooth.com. 

## **6.7 RoHS and REACH Declaration** 

The latest declaration of environmental compatibility (Restriction of Hazardous Substances, RoHS and Registration, Evaluation, Authorisation and Restriction of Chemicals, REACH) for supplied products can be found on the Panasonic website in the “Downloads” section of the respective product  7.2.2 Product Information. 

Product Specification Rev. 1.0 

Page 40 of 42 

 INDUSTRY > PAN1782 Bluetooth Module Panasonic 7 Appendix 

## **7 Appendix** 

## **7.1 Ordering Information** 

## **Variants and Versions** 

|**Order Number**|**Brand Name**|**Description**|**MOQ1**|
|---|---|---|---|
|ENW89858A1KF2|PAN1782|Bluetooth Low Energy Module with Antenna<br>Access Port Protection APPROTECT HW<br>EmptyFlash|1 500|



> 1 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. 

> 2 Samples available on customer demand 

Product Specification Rev. 1.0 

Page 41 of 42 

 PAN1782 Bluetooth Module > 

INDUSTRY Panasonic 7 Appendix 

## **7.2 Contact Details** 

## **7.2.1 Contact Us** 

Please contact your local Panasonic Sales office for details on additional product options and services: 

For Panasonic Sales assistance in the **EU** , visit 

https://eu.industrial.panasonic.com/about-us/contact-us 

Email: wireless@eu.panasonic.com 

For Panasonic Sales assistance in **North America** , visit the Panasonic website “Sales & Support” to find assistance near you at 

https://na.industrial.panasonic.com/distributors 

Please visit the **Panasonic Wireless Technical Forum** to submit a question at 

https://forum.na.industrial.panasonic.com 

## **7.2.2 Product Information** 

Please refer to the Panasonic Wireless Connectivity website for further information on our products and related documents: 

For complete Panasonic product details in the **EU** , visit 

http://pideu.panasonic.de/products/wireless-modules.html 

For complete Panasonic product details in **North America** , visit 

http://www.panasonic.com/rfmodules 

Product Specification Rev. 1.0 

Page 42 of 42
Updated at April 28, 2026
Panasonic Industry is a global leader in the design and manufacture of high-quality electronic components. Renowned for a commitment to continuous innovation, the company provides the essential building blocks that empower modern engineering. From industrial automation to consumer electronics, Panasonic's components are trusted worldwide for their outstanding reliability, efficiency, and long-term performance. The extensive portfolio is anchored by a massive selection of passive components, featuring an industry-leading range of aluminium electrolytic, film, and polymer capacitors. Alongside these advanced capacitance solutions, engineers rely on Panasonic's robust power inductors and a highly versatile array of electromechanical devices, including solid-state, power, and signal relays engineered to excel in demanding environments. Beyond core passives and switching solutions, the offering encompasses critical circuit protection devices such as TVS varistors and NTC thermistors, as well as sophisticated thermal management materials. Panasonic also delivers precision light and motion sensors, highly reliable batteries, and advanced Bluetooth and WLAN connectivity modules, providing a comprehensive ecosystem of components to support next-generation technological design.
About Novapart

Novapart is a B2B electronic component broker specialising in stock shortages and cost reduction. We source hard-to-find parts and identify compliant alternatives across a catalogue of 410,000+ components from 500+ manufacturers.
Learn more →
Stock Shortage Specialist

When a component is unavailable, discontinued or has an unacceptable lead time, we tap into our network of vetted European and Asian distributors to source what you need — without compromising on quality or traceability.
Request a quote →
Compliant Alternatives

We identify pin-to-pin, electrically equivalent substitutes that meet the same certifications (RoHS, AEC-Q100, REACH) as your original specification — validated against datasheets, not just part numbers. Often at a lower cost.
BOM Analysis service →