Image not available
Illustrative purposes only
ENW89854A1KF
Bluetooth Module, Bluetooth LE 5.1, 2.45Ghz, IEEE 802.15.4, 1.7V to 5.5V
⚠️ Reference pricing provided. In case of supply shortages, we will connect you with our trusted procurement partners to ensure your project's continuity.
- Manufacturer: PANASONIC
- Product type: Bluetooth Modules & Adaptors
- Available until stocks are exhausted
- SVHC: No SVHC (25-Jun-2025)
- Interfaces: I2C, I2S, SPI, UART
- Product Range: PAN1780 Series
- Certifications: FCC, ISED, KC, MIC, RCM, RED, SRRC, UKCA
- Bluetooth Class: -
- Bluetooth Version: Bluetooth LE 5.0
- Supply Voltage Range: 1.7 V to 5.5 V
- Receiver Sensitivity Rx: -103 dBm
- Operating Temperature Range: -40 °C to 85 °C
| Delivery and price | |
|---|---|
| Units per pack | 250 |
| Price | 8.32 € |
| Current stock | 500+ |
| Lead time | 30 days |
Datasheet
## PAN1780 Bluetooth[®] Low Energy Module Product Specification Rev. 1.6 Wireless Connectivity PAN1780 Bluetooth Module ## **Overview** The PAN1780 is a Bluetooth 5.3 qualified[1] Low Energy (LE) module based on the Nordic nRF52840 single chip controller. ## **[Bluetooth Features ]** - [LE 2M and LE Coded ] - [LE advertising extensions (advertising on 40 ] channels total) - [Channel selection algorithm #2 ] - [LE secure connections ] ## **Features** - [Surface mount type dimensions: ] 15.6 mm × 8.7 mm × 2 mm - [Same form factor as PAN1026A and PAN1762 ] but smaller pitch and more pins - [Nordic nRF52840 featuring ARM][®][ Cortex][®][-M4F ] with 64 MHz - [Bluetooth 5.3 LE including LE 2M and LE Coded ] PHY - [Embedded 1 MB flash memory and 256 kB ] internal RAM - [Supports 802.15.4 ZigBee][®][ and Thread ] - [Includes ARM TrustZone][®][ CryptoCell][®][ 310 and ] supports secure boot including Root of Trust (RoT) - [Up to 48× General Purpose I/Os (GPIO), which ] are shared by up to 4× SPI, 2× I²C, 2× UART, 4× PWM, 8× ADC, 1× NFC-A, 32 kHz IN/OUT, nRESET - [Over-the-air update of application software ] - [Qualified Bluetooth mesh profile stack ] ## **Characteristics** - [Typical sensitivity: -95 dBm at 1 Mbps ] and -103 dBm at 125 kbps - [Output power: up to 8 dBm (configurable ] from -20 dBm in 4 dB steps and -40 dBm in whisper mode) - [Typical current consumption: 4.8 mA in Tx ] (at 0 dBm) and 4.8 mA in Rx mode - [Typical current consumption: 0.4 µA in System ] OFF mode, 1.5 µA with RTC wake up - [On-module DC-DC and LDO regulators with ] automated low current modes - [Voltage range: 1.7 V to 5.5 V ] - [Temperature range: -40 °C to 85 °C ] - [USB 2.0 full-speed device interface ] - [Built-in temperature sensor ] - [APPROTECT variant available ] ## **Block Diagram** > 1 The nRF52840 is also capable of Bluetooth 5.4, but the module is not yet qualified. Product Specification Rev. 1.6 Page 2 of 59 - PAN1780 Bluetooth Module - > ## PAN1780 Bluetooth Module ## INDUSTRY Panasonic By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2025. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Product Specification does not lodge the claim to be complete and free of mistakes. If this document is marked as preliminary, please be aware that its final content is not yet concluded and the use of it is at your own risk. ## **Document Acceptance** By signing the Product Specification, you acknowledge that you are a legal representative for your company and that you understand and accept the validity of the contents herein. If the signed version of the Product Specification has not been returned to Panasonic within 30 days after receipt of the product, the specification or approval sheet shall be deemed to be accepted by you. ## **Engineering Samples (ES)** If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. ## **Disclaimer** The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by: - The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, - Deviation or lapse in function of the Engineering Sample, - Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. Product Specification Rev. 1.6 Page 3 of 59 - PAN1780 Bluetooth Module - > ## INDUSTRY Panasonic ## **Product Change Notifications (PCNs) and Information Notes (INs)** Please consider the following PCNs/INs and take suitable countermeasures where necessary and appropriate; for further details please contact your local Panasonic Sales office ( 7.2.1 Contact Us): - Nordic APPROTECT vulnerability problem description: IN133 Informational Notice v1.0 - Nordic APPROTECT solution description: IN141 Informational Notice v1.1 - The vulnerabilty issue can be fixed by using the PAN1780 module with order number ENW89854A4KF and following the instructions on software given in Nordic APPROTECT solution description: IN141 Informational Notice v1.1 ## **Information on Software** The PAN1780 module does not contain any software ex works, i.e. software is provided by 3rd party suppliers only. The essential software resources can be found on the partner website of Nordic Semiconductor https://www.nordicsemi.com/. PIDEU provides a factory software programming service for your customized firmware; for further information please reach out to your local sales contact this regarding 7.2.1 Contact Us. Product Specification Rev. 1.6 Page 4 of 59 - PAN1780 Bluetooth Module - > ## INDUSTRY Panasonic ## **Table of Contents** |**1**|**About This Document ......................................................................................................................... 6**|**About This Document ......................................................................................................................... 6**| |---|---|---| ||1.1|Purpose and Audience .............................................................................................................. 6| ||1.2|Revision History ......................................................................................................................... 6| ||1.3|Use of Symbols ......................................................................................................................... 7| ||1.4|Related Documents ................................................................................................................... 7| |**2**|**Overview .............................................................................................................................................. 8**|| ||2.1|Block Diagram ........................................................................................................................... 9| ||2.2|Pin Configuration ..................................................................................................................... 10| ||2.3|Peripherals .............................................................................................................................. 13| ||2.4|Bluetooth Features .................................................................................................................. 13| |**3**|**Detailed Description ......................................................................................................................... 14**|| ||3.1|Dimensions .............................................................................................................................. 14| ||3.2|Footprint .................................................................................................................................. 15| ||3.3|Packaging ................................................................................................................................ 16| ||3.4|Case Marking .......................................................................................................................... 19| |**4**|**Specification and Integration Recommendations .......................................................................... 20**|| ||4.1|Default Test Conditions ........................................................................................................... 20| ||4.2|Absolute Maximum Ratings ..................................................................................................... 20| ||4.3|Recommended Operating Conditions ...................................................................................... 21| ||4.4|Current Consumption............................................................................................................... 21| ||4.5|Bluetooth RF Characteristics ................................................................................................... 22| ||4.6|Access Port Protection APPROTECT...................................................................................... 23| ||4.7|Antenna Placement Recommendation .................................................................................... 25| ||4.8|Reliability Tests ....................................................................................................................... 27| ||4.9|Recommended Soldering Profile ............................................................................................. 28| |**5**|**Cautions ............................................................................................................................................ 29**|| ||5.1|Design Notes ........................................................................................................................... 29| ||5.2|Installation Notes ..................................................................................................................... 29| ||5.3|Usage Condition Notes ............................................................................................................ 30| ||5.4|Storage Notes .......................................................................................................................... 30| ||5.5|Safety Cautions ....................................................................................................................... 30| ||5.6|Other Cautions ........................................................................................................................ 31| ||5.7|Restricted Use ......................................................................................................................... 32| |**6**|**Regulatory and Certification Information ....................................................................................... 33**|| ||6.1|For Bluetooth Low Energy ....................................................................................................... 34| ||6.2|For IEEE 802.15.4 ................................................................................................................... 48| ||6.3|RoHS and REACH Declaration ............................................................................................... 57| |**7**|**Appendix ........................................................................................................................................... 58**|| ||7.1|Ordering Information ................................................................................................................ 58| ||7.2|Contact Details ........................................................................................................................ 59| Product Specification Rev. 1.6 Page 5 of 59 PAN1780 Bluetooth Module > 1 About This Document ## INDUSTRY 1 About This Document Panasonic ## **1 About This Document** ## **1.1 Purpose and Audience** This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1780 module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN1780” or “the module” within this document. ## **1.2 Revision History** |**Revision**|**Date**|**Modifications/Remarks**| |---|---|---| |1.0|2020-03-12|First preliminary version| |1.1|2020-04-27|•Updated4.2 Absolute Maximum Ratings<br>•Updated6.1.1 General Certification Information: added SoftDevice S113<br>•Updated6.1.3and6.2.3 Innovation, Science, and Economic Development<br>(ISED) for Canada: added ISED SAR Warning and HVIN<br>•Updated6.1.10 Bluetooth: added Bluetooth ID| |1.2|2021-11-16|•Updated disclaimer<br>•Updated Bluetooth version<br>•Added country certifications information for Japan, Korea, China, New Zealand,<br>Australia<br>•Formal changes| |1.3|2022-03-01|•Introduced order number ENW89854A4KF APPROTECT HW<br>•Added4.6 Access Port Protection APPROTECT<br>•Added IEEE 802.15.4 certification for EU/USA/CAN<br>•Added4.7 Antenna Placement Recommendation<br>•Updated disclaimer| |1.4|2023-06-13|•Updated6.1.1and6.2.1 General Certification Information: added nRF<br>Connect SDK (NCS)<br>•Added certification for UK<br>•Updated Bluetooth version<br>•Updated6.1.10 Bluetooth: added Bluetooth 5.3 corresponding IDs<br>•Corrected description of 8 dBm output power value from “typical max.” to “up to”<br>•Corrected MSL value<br>•Updated7.2 Contact Details| |1.5|2025-03-14|•Updated6 Regulatory and Certification Information: added certification<br>overview<br>•Updated4.5 Bluetooth RF Characteristics<br>•Updated “CMIIT ID”6.1.7 China (Label Requirements)<br>•Added footnotes regarding normal and high voltage modes<br>•Updated value for storage temperature4.2 Absolute Maximum Ratings<br>•Added ordering information for evaluation board7.1 Ordering Information| |1.6|2025-07-29|•Updated info box for RED certification6.2.4 European Conformity According<br>to RED (2014/53/EU)<br>•Changed MOQ for Module7.1 Ordering Information| Product Specification Rev. 1.6 Page 6 of 59 1 About This Document Panasonic - PAN1780 Bluetooth Module - > ## **1.3 Use of Symbols** |**Symbol**|**Description**| |---|---| ||**Note**<br>Indicates important information for the proper use of the product.<br>Non-observance can lead to errors.| |A|**Attention**<br>Indicates important notes that, if not observed, can put the product’s functionality<br>at risk.| |[chapter number]<br>[chapter title]|**Cross reference**<br>Indicates cross references within the document.<br>**Example:**<br>Description of the symbols used in this document1.3 Use of Symbols.| ## **1.4 Related Documents** For related documents please refer to the Panasonic website 7.2.2 Product Information. Product Specification Rev. 1.6 Page 7 of 59 INDUSTRY PAN1780 Bluetooth Module 2 Overview > Panasonic INDUSTRY 2 Overview Panasonic ## **2 Overview** The PAN1780 is a Bluetooth 5.3 qualified[2] Low Energy (LE) module based on the Nordic nRF52840 single chip controller. The Bluetooth 5.3 features additionally a higher symbol rate of 2 Mbps using the high-speed LE 2M PHY or a significantly longer range using the LE coded PHY at 500 kbps or 125 kbps. The new channel selection algorithm (CSA#2) improves the performance in high interference environments. Furthermore, the new LE advertising extensions allow for much larger amounts of data to be broadcasted in connectionless scenarios. An output power of up to 8 dBm and the high sensitivity of the nRF52840 in combination with the LE coded PHY make the module very attractive in applications, where a long range is required. In addition, the ultra-low current consumption of the PAN1780 make the module an ideal choice for battery powered devices. With the Cortex[®] M4F processor, 256 kB RAM, and the built-in 1 MB flash memory the PAN1780 can easily be used in standalone mode, thereby eliminating the need for an external processor, saving complexity, space, and cost. The rich set of security features from the ARM TrustZone CryptoCell 310 security subsystem provide the necessary means for secure device operation in the IoT space. The PAN1780 also supports Type 2 Near Field Communication (NFC-A) for use in simplified pairing and payment solutions (external antenna required). For related documents please refer to 7.2.2 Product Information. For further information on the variants and versions please refer to 7.1 Ordering Information. > 2 The nRF52840 is also capable of Bluetooth 5.4, but the module is not yet qualified. Product Specification Rev. 1.6 Page 8 of 59 2 Overview PAN1780 Bluetooth Module ## **2.1 Block Diagram** Product Specification Rev. 1.6 Page 9 of 59 - PAN1780 Bluetooth Module - > ## PAN1780 Bluetooth Module ## INDUSTRY 2 Overview Panasonic ## **2.2 Pin Configuration** ## **Pin Assignment** ## Top View G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G12 G13 OOOOO0O0O000 OO F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 OOOOO0O000 E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 OOOOOOCO0OO00 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 OOOOOCO0OO00 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 OOOOO0CO000 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 OOOOO0OCO000 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A12 A13 HOOOCOOCO0O00 OO ## **Pin Functions** |**No.**|**Pin Name**|**Pin Type**|**Description**| |---|---|---|---| |A1 P0.27|A1 P0.27|Digital BI|GPIO| |A2 P0.26|A2 P0.26|Digital BI|GPIO| |A3 P0.04/AIN2|A3 P0.04/AIN2|Digital BI/Analog Input|GPIO/Sensor to ADC| |A4 P0.05/AIN3|A4 P0.05/AIN3|Digital BI/Analog Input|GPIO/Sensor to ADC| |A5 P0.03/AIN1|A5 P0.03/AIN1|Digital BI/Analog Input|GPIO/Sensor to ADC| |A6 P0.02/AIN0|A6 P0.02/AIN0|Digital BI/Analog Input|GPIO/Sensor to ADC| |A7 P0.29/AIN5|A7 P0.29/AIN5|Digital BI/Analog Input|GPIO/Sensor to ADC| |A8 NFC2|A8 NFC2|RF NFC BI|Connect to NFC Antenna| |A9 NFC1|A9 NFC1|RF NFC BI|Connect to NFC Antenna| |A10 GND|A10 GND|Ground|Connect to ground| |A12 GND|A12 GND|Ground|Connect to ground| |A13 GND|A13 GND|Ground|Connect to ground| |B1 P0.06|B1 P0.06|Digital BI|GPIO| |B2 X32k_OUT|B2 X32k_OUT|32 kHz|Leave open| |B3 P0.30/AIN6|B3 P0.30/AIN6|Digital BI/Analog Input|GPIO/Sensor to ADC| Product Specification Rev. 1.6 Page 10 of 59 ## INDUSTRY PAN1780 Bluetooth Module 2 Overview > Panasonic ## INDUSTRY 2 Overview Panasonic |**No.**|**Pin Name**|**Pin Type**|**Description**| |---|---|---|---| |B4 P0.31/AIN7|B4 P0.31/AIN7|Digital BI/Analog Input|GPIO/Sensor to ADC| |B5 P0.28/AIN4|B5 P0.28/AIN4|Digital BI/Analog Input|GPIO/Sensor to ADC| |B6 P1.13|B6 P1.13|Digital BI|GPIO| |B7 P1.10|B7 P1.10|Digital BI|GPIO| |B8 P1.06|B8 P1.06|Digital BI|GPIO| |B9 P1.15|B9 P1.15|Digital BI|GPIO| |B10 GND|B10 GND|Ground|Connect to ground| |C1 P0.08|C1 P0.08|Digital BI|GPIO| |C2 X32k_IN|C2 X32k_IN|32 kHz|Leave open| |C3 P1.03|C3 P1.03|Digital BI|GPIO| |C4 GND|C4 GND|Ground|Connect to ground| |C5 GND|C5 GND|Ground|Connect to ground| |C6 P1.14|C6 P1.14|Digital BI|GPIO| |C7 P1.11|C7 P1.11|Digital BI|GPIO| |C8 P1.12|C8 P1.12|Digital BI|GPIO| |C9 P1.05|C9 P1.05|Digital BI|GPIO| |C10 GND|C10 GND|Ground|Connect to ground| |D1 GND|D1 GND|Ground|Connect to ground| |D2 P1.08|D2 P1.08|Digital BI|GPIO| |D3 P0.07/TRCCLK|D3 P0.07/TRCCLK|Digital BI|GPIO or Trace IF Clock| |D4 GND|D4 GND|Ground|Connect to ground| |D5 GND|D5 GND|Ground|Connect to ground| |D6 P0.24|D6 P0.24|Digital BI|GPIO| |D7 P1.02|D7 P1.02|Digital BI|GPIO| |D8 P1.07|D8 P1.07|Digital BI|GPIO| |D9 GND|D9 GND|Ground|Connect to ground| |D10 GND|D10 GND|Ground|Connect to ground| |E1 LV Mode|E1 LV Mode3|Supply Voltage|1.7 V to 3.6 V| |E2 P1.09/TRCDAT3|E2 P1.09/TRCDAT3|Digital BI|GPIO or Trace IF D3| |E3 GND|E3 GND|Ground|Connect to ground| |E4 P0.17|E4 P0.17|Digital BI|GPIO| |E5 P0.23|E5 P0.23|Digital BI|GPIO| > 3 In the normal voltage mode (1.7 V to 3.6 V) the LV Mode pin (E1) and HV Mode pin (G2) together are connected to the external power supply. Product Specification Rev. 1.6 Page 11 of 59 ## INDUSTRY PAN1780 Bluetooth Module 2 Overview > Panasonic ## INDUSTRY 2 Overview Panasonic |**No.**|**Pin Name**|**Pin Type**|**Description**| |---|---|---|---| |E6 P0.20|E6 P0.20|Digital BI|GPIO| |E7 P0.21|E7 P0.21|Digital BI|GPIO| |E8 SWDCLK|E8 SWDCLK|Digital BI|Serial Wire Debug IF Clock| |E9 P1.04|E9 P1.04|Digital BI|GPIO| |E10 RF_PIN|E10 RF_PIN|Analog BI|Normally leave unconnected| |F1 P0.12/TRCDAT1|F1 P0.12/TRCDAT1|Digital BI|GPIO or Trace IF D1| |F2 P0.11/TRCDAT2|F2 P0.11/TRCDAT2|Digital BI|GPIO or Trace IF D2| |F3 P0.13|F3 P0.13|Digital BI|GPIO| |F4 P0.14|F4 P0.14|Digital BI|GPIO| |F5 P0.15|F5 P0.15|Digital BI|GPIO| |F6 P0.19|F6 P0.19|Digital BI|GPIO| |F7 P1.01|F7 P1.01|Digital BI|GPIO| |F8 P0.25|F8 P0.25|Digital BI|GPIO| |F9 P0.22|F9 P0.22|Digital BI|GPIO| |F10 GND|F10 GND|Ground|Connect to ground| |G1 P0.16|G1 P0.16|Digital BI|GPIO| |G2 HV Mode|G2 HV Mode4|Supply Voltage|2.5 V to 5.5 V (optional)| |G3 GND|G3 GND|Ground|Connect to ground| |G4 USB Mode|G4 USB Mode|Supply Voltage|4.35 V to 5.5 V| |G5 DP|G5 DP|USB D+|Use for USB only| |G6 DM|G6 DM|USB D-|Use for USB only| |G7 nRESET|G7 nRESET|Digital I|Reset Signal Low Active| |G8 P1.00/TRCDAT0|G8 P1.00/TRCDAT0|Digital BI|GPIO or Trace IF D0| |G9 SWDIO|G9 SWDIO|Digital BI|Serial Wire Debug IF Data| |G10 GND|G10 GND|Ground|Connect to ground| |G12 GND|G12 GND|Ground|Connect to ground| |G13 GND|G13 GND|Ground|Connect to ground| > 4 In the high voltage mode (2.5 V to 5.5 V) only the HV Mode pin (G2) is connected to the external power supply. The LV Mode pin (E1) is not connected. Product Specification Rev. 1.6 Page 12 of 59 PAN1780 Bluetooth Module 2 Overview - PAN1780 Bluetooth Module - > ## INDUSTRY 2 Overview Panasonic ## **2.3 Peripherals** - Full-speed USB 2.0 device controller - 2× UART (2 or 4 wire with CTS/RTS, 1 200 up to 1 M baud) - I[2] C, I[2] S, SPI (32 MHz) - QSPI (32 MHz) - PWM - PDM - AES and CryptoCell - 8× channels 12 bit ADC - Comparator - Quadrature decoder - Temperature sensor - Real time counter - Watchdog timer - 48× GPIOs - Integrated 32 kHz crystal ## **2.4 Bluetooth Features** - Bluetooth LE 5.3 - LE 2M and LE Coded - LE advertising extensions (advertising on 40 channels total) - Channel selection algorithm #2 - LE secure connections - Over-the-air update of application software - Qualified Bluetooth mesh profile stack Product Specification Rev. 1.6 Page 13 of 59 PAN1780 Bluetooth Module 3 Detailed Description ## **3 Detailed Description** ## **3.1 Dimensions** **==> picture [283 x 371] intentionally omitted <==** **----- Start of picture text -----**<br> All dimensions are in millimeters.<br>Top View<br>——<br>be 0<br>15.60<br>2.00<br>1.20<br>8.70<br>**----- End of picture text -----**<br> |**Item**|**Dimension**|**Tolerance**|**Remark**| |---|---|---|---| |Width|8.70|±0.30|±0.30| |Length|15.60|±0.30|±0.30| |Height|2.00|±0.30 With case|±0.30 With case| Product Specification Rev. 1.6 Page 14 of 59 - PAN1780 Bluetooth Module - > ## PAN1780 Bluetooth Module INDUSTRY 3 Detailed Description Panasonic ## **3.2 Footprint** All dimensions are in millimeters. ## Top View G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G12 G13 OO0O0O0C0O00O0C00O OO F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 OOO0O0O00000 E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 OOO0O0O00000 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 OOO0O000000 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 OOO00000000 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 OOO00OO00000 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A12 A13 TOOO0O0O00000 OO ~~-~~ 1.00 1.10 : 0.60 2.20 1.40 15.60 Product Specification Rev. 1.6 Page 15 of 59 > 3 Detailed Description Panasonic **==> picture [195 x 89] intentionally omitted <==** **----- Start of picture text -----**<br> <br>PAN1780 Bluetooth Module<br>><br>**----- End of picture text -----**<br> ## **3.3 Packaging** The module is a mass production status product and will be delivered in the package described below. ## **3.3.1 Tape Dimensions** ## **3.3.2 Packing in Tape** ## Direction of unreeling (for customer) trailer (empty) component leader (empty) Top cover tape more 1 x circumference / packed area minimum 10 pitch than 1 x circumference plus hub standard 100mm to avoid (min 160mm) 1500pcs fixing of tape end on sealed modules. Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive. The top cover tape shall not be found on reel holes and it shall not stick out from the reel. Product Specification Rev. 1.6 Page 16 of 59 PAN1780 Bluetooth Module 3 Detailed Description ## **3.3.3 Component Direction** **==> picture [312 x 115] intentionally omitted <==** **----- Start of picture text -----**<br> Pin 1 Marking<br>(Top Side)<br>Direction of<br>unreeling<br>(for customer)<br>_. x<br>**----- End of picture text -----**<br> ## **3.3.4 Reel Dimension** Product Specification Rev. 1.6 Page 17 of 59 PAN1780 Bluetooth Module wt INDUSTRY 3 Detailed Description Panasonic ## **3.3.5 Package Label** ## **Example:** (1T) Lot code (1P) Customer order number, if applicable (2P) Order number (9D) Date code (Q) Quantity (HW/SW) Hardware/software version ## **3.3.6 Total Package** Product Specification Rev. 1.6 Page 18 of 59 PAN1780 Bluetooth Module > ## 3 Detailed Description Panasonic ## **3.4 Case Marking** ## **Example:** - 1 Brand name - 2 Hardware/software version - 3 Order number - 4 Lot code - 5 Status: ES or empty for MP - 6 2D barcode, for internal usage only - 7 Marking for Pin 1 - 8 Bluetooth logo Product Specification Rev. 1.6 Page 19 of 59 4 Specification and Integration Recommendations PAN1780 Bluetooth Module ## **4 Specification and Integration Recommendations** **==> picture [30 x 30] intentionally omitted <==** **----- Start of picture text -----**<br> @<br>**----- End of picture text -----**<br> All specifications are over temperature and process, unless indicated otherwise. ## **4.1 Default Test Conditions** @ Temperature: 25 °C ± 10 °C Humidity: 40 % to 85 % RH Supply Voltage: 3.3 V ## **4.2 Absolute Maximum Ratings** The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. |**Symbol**|**Parameter**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---|---| |VDD|Normal Supply Voltage||-0.3|-0.3|+3.9|V| |VDDH|High Supply Voltage||-0.3|-0.3|+5.8|| |VBUS|USB Bus Voltage||-0.3|-0.3|+5.8|| |I/O Pin|Voltage on any Pin|VDD≤ 3.6 V|-0.3|-0.3|VDD+ 0.3|| |||VDD> 3.6 V|-0.3|-0.3|3.9|| |ESD|ESD Robustness|HBM 1C|||1 000|| |||CDM|||500|| |MSL|Moisture Sensitivity Level|Moisture Sensitivity Level|||3|| |PRF|RF Input Level||||+10|dBm| |TSTOR|Storage Temperature||-40|-40|+85|°C| Product Specification Rev. 1.6 Page 20 of 59 PAN1780 Bluetooth Module > 4 Specification and Integration Recommendations ## Panasonic ## **4.3 Recommended Operating Conditions** The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. |**Symbol**|**Parameter**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---|---| |VDD(LV Mode)|Supply Voltage||1.7||3.6|V| |tR_ VDD|Supply Rise<br>Time|0 V to 1.7 V|||60|ms| |VDD-POR|SupplyVoltage|Power On Reset active|1.75|||V| |VDDH (HV Mode)|SupplyVoltage|VDDH- Optional|2.5||5.5|V| |tR_VDDH|Supply Rise<br>Time|0 V to 3.7 V|||100|ms| |VBUS|VBUS USB<br>Supply Voltage|VBUS- Optional|4.35||5.5|V| |TA|Operating<br>Temperature||-40|25|85|°C| ## **4.3.1 Digital Pin Characteristics** |**Symbol**|**Parameter**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---|---| |VIH|Input High Voltage||0.7*VDD||VDD|V| |VIL|Input Low Voltage||GND||0.3*VDD|V| |VOH|Output High Voltage||VDD– 0-4||VDD|V| |VOL|Output Low Voltage||GND||GND + 0.4|V| |RPU/PD|Internal pull-up/pull-<br>down resistance||11|13|16|kΩ| ## **4.4 Current Consumption** The current consumption depends on the user scenario and on the setup and timing in the power modes. Assume VDD = 3.3 V, Tamb = 25 °C, if nothing else stated, DC/DC enabled. |**Parameter**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---| |Sleep Mode|No RAM retention, Wake on Reset, SYS OFF||0.4|0.4|µA| ||Full RAM retention, Wake on Reset, SYS OFF||1.86|1.86|µA| Product Specification Rev. 1.6 Page 21 of 59 - PAN1780 Bluetooth Module - > ## INDUSTRY Panasonic ## 4 Specification and Integration Recommendations |**Parameter**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---| ||No RAM retention, Wake on any event,<br>SYS ON||0.97|0.97|µA| ||Full RAM retention, Wake on any event,<br>SYS ON||2.35|2.35|µA| ||No RAM retention, Wake on RTC, SYS ON||1.5|1.5|µA| |CPU executing<br>CoreMark|Running from RAM||2.8|2.8|mA| ||Running from Flash||3.3|3.3|mA| |Rx Current|||4.8|4.8|mA| |Tx Current|8 dBm||14.8||mA| ||4 dBm||9.6||mA| ||0 dBm||4.8||mA| ||-4 dBm||3.1||mA| ||-8 dBm||3.3||mA| ||-12 dBm||3.0||mA| ||-16 dBm||3.8||mA| ||-20 dBm||2.7||mA| ||-40 dBm||2.3||mA| ## **4.5 Bluetooth RF Characteristics** ## **4.5.1 Transmitter RF Characteristics** |**Parameter**|**Condition**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---|---| |Frequency Range|Frequency Range||2 402||2 480|MHz| |Output Power||||+8||dBm| |Data Rate|||125||2 000|Kbps| |Adjacent Channel<br>Transmit Power|1 Mbps|1stAdjacent Channel||-24.8||dBc| |||2ndAdjacent Channel||-54||dBc| ||2 Mbps|1stAdjacent Channel||-25||dBc| |||2ndAdjacent Channel||-54||dBc| ## **4.5.2 Receiver RF Characteristics** |**Parameter**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---| |Receiver<br>Sensitivity|1 Mbps, Payload ≤ 37 bytes, BER ≤ 0.1 %||-95||dBm| ||2 Mbps, Payload ≤ 37 bytes, BER ≤ 0.1 %||-92||dBm| ||125 Kbps LR S8, BER ≤ 0.1 %||-103||dBm| ||500 Kbps LR S2, BER ≤ 0.1 %||-99||dBm| Product Specification Rev. 1.6 Page 22 of 59 - PAN1780 Bluetooth Module - > ## INDUSTRY Panasonic ## 4 Specification and Integration Recommendations |**Parameter**|**Condition**|**Condition**|**Min.**|**Typ.**|**Max.**|**Unit**| |---|---|---|---|---|---|---| |Interference<br>Characteristics|1 Mbps<br>Signal Level = -67 dBm<br>BER ≤ 0.1 %|C/I (Co-channel)||6||dB| |||C/I (1 MHz)||-2||dB| |||C/I (2 MHz)||-22||dB| |||C/I (≥3 MHz)||-50||dB| |||C/I (Image)||-22||dB| |||C/I (Image,1 MHz)||-35||dB| ## **4.6 Access Port Protection APPROTECT** If using the APPROTECT version of the PAN1780 with order number ENW89854A4KF a special sequence of commands is necessary during production programming. These commands ensure that the built-in Bluetooth Device Address is preserved when the access port protection is enabled. The access port protection prevents (amongst others) any access to the built-in flash memory through the device debug port. In factory state, the PAN1780 with order number ENW89854A4KF implementing Nordic nRF52840 “revision 3 silicon” comes with the access port protection disabled. ## **Locking the Device Debug Port and enabling the Access Port Protection** Once the access port protection is enabled, no further access including debugging can be done anymore! To ensure that the device debug port is locked during production programming and the access port protection is enabled correctly, the following steps must be followed. 1. Use the Microcontroller Development Kit (MDK) nRF MDK (version 8.40.2) or later version for application development. - If the application is based on nRF5 SDK (version 17.1.0) or later version, compile the application with the globally defined `ENABLE_APPROTECT` -define. Open the project in **Segger Embedded Studio** . Set the define in **Project** **options** > Section **Code** > **Preprocessor Options** > **Preprocessor Definitions** . - If the application is based on nRF Connect SDK (version 1.8.0) or later version, compile the application with the option set `CONFIG_NRF_APPROTECT_LOCK=y` , for example in the project configuration file `prj.conf` . 2. Use the nRF Command Line Tools (version 10.15.2) for production programming. Please make sure to use version 10.15.2 or later. 3. Execute `nrfjprog.exe --verify fast --sectorerase --program application.hex` from a command line prompt to program an application HEX file: Product Specification Rev. 1.6 Page 23 of 59 - PAN1780 Bluetooth Module - > PAN1780 Bluetooth Module ## INDUSTRY Panasonic 4 Specification and Integration Recommendations `Parsing image file. Verifying programming. Verified OK.` 4. Execute `nrfjprog.exe --rbp ALL` from a command line prompt to enable the access port protection: `Protected the device against read and debug. Only a --recover, --debugreset, or --pinreset operations will work from now on.` It is possible to disable the access port protection again using the option `recover` , but the complete PAN1780 module is erased including the built-in Bluetooth Device Address. For details how to prevent this during application development, please refer to the “PAN1780 EVB User Guide (“Bluetooth Address Safeguard”)”. For technical details please refer to IN141 Informational Notice v1.1 in the Nordic Infocenter https://infocenter.nordicsemi.com/. Product Specification Rev. 1.6 Page 24 of 59 4 Specification and Integration Recommendations ## PAN1780 Bluetooth Module ## **4.7 Antenna Placement Recommendation** **Antenna “Keep out Area”** Do not place any ground plane under the marked restricted antenna area in any layer! This would be affecting the performance of the chip antenna in a critical manner. ## **Impact of Placement on the Antenna Radiation Pattern** The placement of the module, surrounding material, and customer components has an impact on the radiation pattern of the antenna. The recommendation for the ground plane is based on a FR4 4-Layer PCB. The following requirements must be met: - ✓ Keep this product away from heat. Heat is the major cause of decreasing the life of these products. - ✓ Keep this product away from other high frequency circuits. The antenna requires a cutout area of 5 mm × 3 mm under the PAN1780 module. This “Keep out Area” shall be located in every layer under the module antenna. Note for example the “Keep out Area” in all four layers of the PAN1780 evaluation board. It is recommended to verify the perfect position of the module in the target application before fixing the design. Product Specification Rev. 1.6 Page 25 of 59 PAN1780 Bluetooth Module > > 4 Specification and Integration Recommendations Panasonic ## **Antenna Placement Recommendation** All dimensions are in millimeters. Use a ground plane in the area surrounding the module wherever possible. It is recommended to place the module: - In the center (horizontal) of any mother PCB edge, - with GND planes to the left and right. ## Top View **==> picture [286 x 208] intentionally omitted <==** **----- Start of picture text -----**<br> Min. 15.00 8.70 Min. 15.00<br>5.00<br>Keep out<br>Area<br>Top View<br>| i<br>3.00<br>15.60<br>Min. 40.00<br>**----- End of picture text -----**<br> Product Specification Rev. 1.6 Page 26 of 59 PAN1780 Bluetooth Module > INDUSTRY Panasonic 4 Specification and Integration Recommendations ## **4.8 Reliability Tests** The measurement should be done after the test module has been exposed to room temperature and humidity for one hour. |**No.**|**Item**|**Limit**|**Condition**| |---|---|---|---| |1 Variable Vibration Test Electrical parameters should be|1 Variable Vibration Test Electrical parameters should be|1 Variable Vibration Test Electrical parameters should be<br>within specification|Freq.: 20~2 000 Hz, Acc.: 17-50 G,<br>Sweep: 8 min, 2 hours, For: XYZ axis| |2 Shock Drop Test|2 Shock Drop Test||Drop parts on concrete from a height of<br>1 m for 3 times| |3 Heat-Shock/|3 Heat-Shock/<br>Temperature Cycling<br>Test||At -40 °C and 85 °C for 1 h/cycle<br>Total = 300 cycles| |4 Temperature Humidity|4 Temperature Humidity<br>Bias Test||At 60 °C, 85 % r.H., 300 h| |5 Low Temperature|5 Low Temperature<br>Storage Life Test||At -40 °C, 300 h| |6 High Temperature|6 High Temperature<br>Storage Life Test||At 85 °C, 300 h| Product Specification Rev. 1.6 Page 27 of 59 PAN1780 Bluetooth Module 4 Specification and Integration Recommendations ## **4.9 Recommended Soldering Profile** - Reflow permissible cycles: 2 - Opposite side reflow is prohibited due to module weight - More than 75 percent of the soldering area shall be coated by solder - The soldering profiles should be adhered to in order to prevent electrical or mechanical damage - Soldering profile assumes lead-free soldering Product Specification Rev. 1.6 Page 28 of 59 INDUSTRY 5 Cautions Panasonic PAN1780 Bluetooth Module > ## **5 Cautions** Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module. ## **5.1 Design Notes** 1. Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage should abide by the maximum ratings ( 4.2 Absolute Maximum Ratings). 3. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 µF directly at the module). 4. This module should not be mechanically stressed when installed. 5. Keep this module away from heat. Heat is the major cause of decreasing the life time of these modules. 6. Avoid assembly and use of the target equipment in conditions where the module temperature may exceed the maximum tolerance. 7. Keep this module away from other high frequency circuits. 8. Refer to the recommended pattern when designing a board. ## **5.2 Installation Notes** 1. Reflow soldering is possible twice based on the conditions set forth in 4.9 Recommended Soldering Profile. Set up the temperature at the soldering portion of this module according to this reflow profile. 2. Carefully position the module so that the heat will not burn into printed circuit boards or affect other components that are susceptible to heat. 3. Carefully locate the module, to avoid an increased temperature caused by heat generated by neighboring components. 4. If a vinyl-covered wire comes into contact with the module, the wire cover will melt and generate toxic gas, damaging the insulation. Never allow contact between a vinyl cover and these modules to occur. 5. This module should not be mechanically stressed or vibrated when reflowed. 6. To repair the board by hand soldering, follow the conditions set forth in this chapter. 7. Do not wash this product. 8. Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the module. Product Specification Rev. 1.6 Page 29 of 59 INDUSTRY 5 Cautions Panasonic PAN1780 Bluetooth Module 5 Cautions - PAN1780 Bluetooth Module - > ## **5.3 Usage Condition Notes** 1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 2. Do not use dropped modules. 3. Do not touch, damage, or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this module. 5. Electrode peeling strength: Do not apply a force of more than 4.9 N in any direction on the soldered module. 6. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. 7. These modules are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information, and communication equipment. ## **5.4 Storage Notes** 1. The module should not be stressed mechanically during storage. 2. Do not store these modules in the following conditions or the performance characteristics of the module, such as RF performance will be adversely affected: - Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX, - Storage in direct sunlight, - Storage in an environment where the temperature may be outside the range of 5 °C to 35 °C, or where the humidity may be outside the 45 % to 85 % range, - Storage of the modules for more than one year after the date of delivery storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. 3. Keep this module away from water, poisonous gas, and corrosive gas. 4. This module should not be stressed or shocked when transported. 5. Follow the specification when stacking packed crates (max. 10). ## **5.5 Safety Cautions** These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, provide the following failsafe functions as a minimum: Product Specification Rev. 1.6 Page 30 of 59 INDUSTRY PAN1780 Bluetooth Module 5 Cautions > Panasonic INDUSTRY 5 Cautions Panasonic 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. ## **5.6 Other Cautions** 1. Do not use the module for other purposes than those listed in 5.3 Usage Condition Notes. 2. Be sure to provide an appropriate fail-safe function on your product to prevent any additional damage that may be caused by the abnormal function or the failure of the module. 3. This module has been manufactured without any ozone chemical controlled under the Montreal Protocol. 4. These modules are not intended for use under the special conditions shown below. Before using these modules under such special conditions, carefully check their performance and reliability under the said special conditions to determine whether or not they can be used in such a manner: - In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash, - In direct sunlight, outdoors, or in a dusty environment, - In an environment where condensation occurs, - In an environment with a high concentration of harmful gas (e. g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX). 5. If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these modules with new modules, because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. For further information please refer to the Panasonic website 7.2.2 Product Information. Product Specification Rev. 1.6 Page 31 of 59 PAN1780 Bluetooth Module > INDUSTRY 5 Cautions Panasonic ## **5.7 Restricted Use** ## **5.7.1 Life Support Policy** This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. ## **5.7.2 Restricted End Use** This Panasonic Industrial Devices Europe GmbH product is not designed for any restricted activity that supports the development, production, handling usage, maintenance, storage, inventory or proliferation of any weapons or military use. Transfer, export, re-export, usage or reselling of this product to any destination, end user or any end use prohibited by the European Union, United States or any other applicable law is strictly prohibited. Product Specification Rev. 1.6 Page 32 of 59 PAN1780 Bluetooth Module > INDUSTRY 6 Regulatory and Certification Information Panasonic ## **6 Regulatory and Certification Information** This chapter contains regulatory and certification information for: - Bluetooth Low Energy 6.1 For Bluetooth Low Energy - IEEE 802.15.4 6.2 For IEEE 802.15.4 For the device the following certifications are available: ## **Bluetooth Low Energy** |**Certification**|**Certification**|**Status**|**Reference**| |---|---|---|---| |FCC|for US|Available|6.1.2 Federal Communications<br>Commission (FCC) for US| |ISED|for Canada|Available|6.1.3 Innovation, Science, and Economic<br>Development (ISED) for Canada| |RED|for Europe|Available|6.1.4 European Conformity According to<br>RED (2014/53/EU)| |UKCA|for United Kingdom Available|for United Kingdom Available|6.1.5 United Kingdom Conformity<br>According to Statutory Instrument SI<br>2017/1206| |MIC|for Japan|Available|6.1.6 Japanese Radio Law Compliance| |SRRC|for China|Available|6.1.7 China(Label Requirements)| |KCC|for Korea|Available|6.1.8 Korea(Label Requirements)| |RCM|for Australia<br>and New Zealand|Available|6.1.9 Australia and New Zealand<br>Conformity According to RCM| ## **IEEE 802.15.4** |**Certification**|**Certification**|**Status**|**Reference**| |---|---|---|---| |FCC|for US|Available|6.2.2 Federal Communications<br>Commission (FCC) for US| |ISED|for Canada|Available|6.2.3 Innovation, Science, and Economic<br>Development (ISED) for Canada| |RED|for Europe|Available|6.2.4 European Conformity According to<br>RED (2014/53/EU)| |UKCA|for United Kingdom Available|for United Kingdom Available|6.2.5 United Kingdom Conformity<br>According to Statutory Instrument SI<br>2017/1206| |MIC|for Japan|Upon request|| |SRRC|for China|Upon request|| |KCC|for Korea|Upon request|| |RCM|for Australia<br>and New Zealand|Upon request|| Product Specification Rev. 1.6 Page 33 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module **==> picture [34 x 30] intentionally omitted <==** **----- Start of picture text -----**<br> @<br>**----- End of picture text -----**<br> For regions “upon request”, please reach out to your Sales contact for the most recent status of the certification process 7.2.1 Contact Us. ## **6.1 For Bluetooth Low Energy** ## **6.1.1 General Certification Information** Regulatory certifications are valid for the following radio relevant software: - Nordic SoftDevice S140, S113, and Wirepas v4.x or v5.x - nRF Connect SDK - Softdevice - Controller - Bluetooth Specification 5.3 Regulatory certifications stay valid for APPROTECT versions provided that: If the nRF52840 new silicon revision 3 with access port protection, which is implemented in the PAN1780 with Panasonic order number ENW89854A4KF is used: - Nordic IN141 Informational Notice v1.1 states “The new revision has no impact on CE, FCC/ISED or Bluetooth certifications unless the new pulse shaping filter is enabled.” - Nordic FTPAN-254 describes how to enable the pulse shaping filter, but as stated before it needs to remain disabled. Hence the code described in Nordic FTPAN-254 shall not be implemented/executed; otherwise the PAN1780 pre-certification becomes invalid. The Nordic FTPAN-254 workaround is meant for designs using an PA/LNA RF front end, which is not feasible with the PAN1780. Therefore, it is not useful to implement Nordic FTPAN-254. For further certification requests for other radio software please contact Panasonic 7.2 Contact Details. Product Specification Rev. 1.6 Page 34 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module ## **6.1.2 Federal Communications Commission (FCC) for US** ## **6.1.2.1 FCC Notice** **==> picture [31 x 29] intentionally omitted <==** **----- Start of picture text -----**<br> @<br>**----- End of picture text -----**<br> The PAN1780 including the antennas, which are listed in 6.1.2.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ## **6.1.2.2 Caution** The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna, - Increase the separation between the equipment and receiver, - Connect the equipment into an outlet on a circuit different from that to which the receiver is - connected, - Consult the dealer or an experienced radio/TV technician for help. Product Specification Rev. 1.6 Page 35 of 59 PAN1780 Bluetooth Module > INDUSTRY Panasonic 6 Regulatory and Certification Information ## **6.1.2.3 Label Requirements** The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is **FCC ID: T7V1780** . This FCC identifier is valid for the PAN1780. The end product must in any case be labelled on the exterior with: "Contains FCC ID: T7V1780". Due to the PAN1780 model size, the FCC identifier is displayed in the installation instruction only and it cannot be displayed readable on the module’s label due to the limited size. ## **6.1.2.4 Antenna Warning** This antenna warning refers to the test device with the model number PAN1780 7.1 Ordering Information. The device is tested with a standard SMA connector and with the antenna listed below. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions. The FCC identifier for the device with the antenna listed in 6.1.2.5 Approved Antenna List is the same ( **FCC ID: T7V1780** ). ## **6.1.2.5 Approved Antenna List** |**Item**|**Part Number**|**Manufacturer**|**Frequency Band**|**Type**|**Max. Gain**<br>**(dBi)**| |---|---|---|---|---|---| |1 ANT016008LCS2442MA1 TDK|1 ANT016008LCS2442MA1 TDK|1 ANT016008LCS2442MA1 TDK|2.4 GHz|Chip antenna|-1| Product Specification Rev. 1.6 Page 36 of 59 PAN1780 Bluetooth Module > INDUSTRY Panasonic 6 Regulatory and Certification Information ## **6.1.2.6 RF Exposure** To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.2.5 Approved Antenna List. The preceding statement must be included as a “CAUTION” statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of the PAN1780 with a mounted ceramic antenna ( **FCC ID: T7V1780** ) is below the FCC radio frequency exposure limits. Nevertheless, the PAN1780 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. Product Specification Rev. 1.6 Page 37 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module - PAN1780 Bluetooth Module - > ## INDUSTRY Panasonic ## **6.1.3 Innovation, Science, and Economic Development (ISED) for Canada** ## **English** The PAN1780 is licensed to meet the regulatory requirements of ISED. License ID: **IC: 216Q-1780** HVIN: **ENW89854A1KF, ENW89854A4KF** Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in 6.1.2.5 Approved Antenna List, having a maximum gain of -1 dBi. Antennas not included in this list or having a gain greater than -1 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 Ω. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size, the IC identifier is displayed in the installation instruction only and it cannot be displayed on the module’s label due to the limited size. The end customer has to assure that the device has a distance of more than 15 mm from the human body under all circumstances. If the end customer application intends to use the PAN1780 in a distance smaller 15 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to ISED. ## **French** PAN1780 est garanti conforme aux dispositions règlementaires d’Industry Canada (ISED). License: **IC: 216Q-1780** HVIN: **ENW89854A1KF, ENW89854A4KF** Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique maximum autorisé. Des informations pour les utilisateurs sur la réglementation Canadienne concernant l’exposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. Product Specification Rev. 1.6 Page 38 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module Ce produit a été développé pour fonctionner spécifiquement avec les antennes listées dans le tableau 6.1.2.5 Approved Antenna List, présentant un gain maximum de -1 dBi. Des antennes autres que celles listées ici, ou présentant un gain supérieur à -1 dBi ne doivent en aucune circonstance être utilisées en combinaison avec ce produit. L’impédance des antennes compatibles est 50 Ω. L’antenne utilisée avec ce produit ne doit ni être située à proximité d’une autre antenne ou d’un autre émetteur, ni être utilisée conjointement avec une autre antenne ou un autre émetteur. En raison de la taille du produit, l’identifiant IC est fourni dans le manuel d’installation. Le client final doit s'assurer que l'appareil se trouve en toutes circonstances à une distance de plus de 15 mm du corps humain. Si le client final envisage une application nécessitant d'utiliser le PAN1780 à une distance inférieure à 15 mm du corps humain, alors le FEO doit répéter l'évaluation DAS. L'équipement du client final doit répondre aux exigences actuelles de sécurité et de santé selon l’ISED. ## **6.1.3.1 IC Notice** ## **English** @ The device PAN1780 ( 7.1 Ordering Information), including the antennas ( 6.1.2.5 Approved Antenna List), complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ## **French** Le présent appareil PAN1780 ( 7.1 Ordering Information), les antennes y compris ( 6.1.2.5 Approved Antenna List), est conforme aux CNR-Gen d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage, et 2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Product Specification Rev. 1.6 Page 39 of 59 PAN1780 Bluetooth Module > > 6 Regulatory and Certification Information Panasonic ## **6.1.3.2 Labeling Requirements** ## **English** @ ## **Labeling Requirements** The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is **IC: 216Q-1780** . This IC identifier is valid for all PAN1780 modules 7.1 Ordering Information. In any case, the end product must be labelled on the exterior with: "Contains IC: 216Q-1780”. ## **French** ## **Obligations d’étiquetage** Les fabricants d’équipements d’origine (FEO) – en anglais Original Equipment Manufacturer (OEM) – doivent s’assurer que les obligations d’étiquetage IC du produit final sont remplies. Ces obligations incluent une étiquette clairement visible à l’extérieur de l’emballage externe, comportant l’identifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. ## L’ identifiant IC est **IC: 216Q-1780** . Cet identifiant est valide pour tous les modules PAN1780 7.1 Ordering Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante: "Contient IC: 216Q-1780”. Product Specification Rev. 1.6 Page 40 of 59 > 6 Regulatory and Certification Information Panasonic - PAN1780 Bluetooth Module - > ## PAN1780 Bluetooth Module ## **6.1.4 European Conformity According to RED (2014/53/EU)** All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 3.1b EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) 3.2 Radio: EN 300 328 V2.2.2: (2019-07) - Due to the model size, the CE marking is displayed in the installation instruction only and it cannot be displayed conform to regulation (EU) No. 765/2008 in 5 mm height on the module’s label due to the limited space. - The RED EU Type Examination Certificate No. **T818666M** issued by the Notified Body 0682 can be used for the OEM end product conformity assessment. If a Notified Body has been contracted for the end product conformity assessment, it should be noted that this EU Type Examination Certificate should be used for conformance assessment. As a result of the conformity assessment procedure described in 2014/53/EU Directive, the end customer equipment should be labelled as follows: The requirements for CE marking are described in regulation (EC) No. 765/2008 Annex II. The end customer has to assure that the device has a distance of more than 5 mm from the human body under all circumstances. If the end customer application intends to use the PAN1780 in a distance smaller 5 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to RED. PAN1780 and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra, and Turkey. Product Specification Rev. 1.6 Page 41 of 59 > 6 Regulatory and Certification Information Panasonic - PAN1780 Bluetooth Module - > PAN1780 Bluetooth Module ## **6.1.5 United Kingdom Conformity According to Statutory Instrument SI 2017/1206** All modules described in this Product Specification comply with the designated standards according to the following Regulations: Electrical Equipment (Safety) SI 2016/1101, EMC SI 2016/1091 together with Radio Equipment Regulation 2017 (RER) SI 2017/1206: Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) Radio: EN 300 328 V2.2.2: (2019-07) - Due to the model size, the UK marking is displayed in the installation instruction only and it cannot be displayed conform to SI 2017/1206 on the module’s label due to the limited space. - The RED EU Type Examination Certificate No. **T818666M** issued by the EU Notified Body 0682 can be used for the OEM end product conformity assessment. If a Notified Body has been contracted for the end product conformity assessment, it should be noted that this EU Type Examination Certificate should be used for conformance assessment. As a result of the conformity assessment procedure described in SI 2017/1206 Directive, the end customer equipment should be labelled as follows: ## ~~ee ee~~ ## **Restrictions or Requirements in the UK** The end customer has to assure that the device has a distance of more than 5 mm from the human body under all circumstances. If the end customer application intends to use the PAN1780 in a distance smaller 5 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to SI 2017/1206. PAN1780 and its model versions in the specified reference design can be used in the UK. Product Specification Rev. 1.6 Page 42 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module ## **6.1.6 Japanese Radio Law Compliance** This device is granted pursuant to the Japanese Radio Law ( `電波法` ). This device should not be modified (otherwise the granted designation number will become invalid). The following models are qualified for the Japanese market: MIC ID: [R]202-DGJ064 Since the printable area on the PAN1780 is too small to show the MIC logo and the MIC ID, this information is placed on the package and in the user information. The package label shows the Giteki mark and the Radio Law sign with the MIC ID as depicted below: **==> picture [316 x 81] intentionally omitted <==** **----- Start of picture text -----**<br> 202-DGJ064<br>— SR<br>**----- End of picture text -----**<br> Any product with the PAN1780 integrated and to be sold on the Japanese market has to display the following statement on the product label: ## **End Product Labelling Example** Contains MIC ID R 202-DGJ064 Product Specification Rev. 1.6 Page 43 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module **==> picture [187 x 89] intentionally omitted <==** **----- Start of picture text -----**<br> <br>PAN1780 Bluetooth Module<br>><br>**----- End of picture text -----**<br> ## INDUSTRY Panasonic ## **6.1.7 China (Label Requirements)** The PAN1780 has a modular CMIIT certification. The OEM must ensure that SRRC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic SRRC identifier for this module. The final Bluetooth product must be marked with an approval code, known as the “China MII ID”, product name, model number, and battery information, place of production, manufacturer name, and CMIIT number. 本设备包含型号核准代码为 CMIIT ID: 2021DJ14922(M) 的无线电发射模块。 Format of the ID is as follows: “ **CMIIT ID: 2021DJ14922(M)** ”, where: - **CMIIT** : Abbreviation for China Ministry of Information Industry - **2021** : Year of application - **DJ** : Code indicating equipment category - **14922(M)** : Approval serial number issued by SRRC ## **End Product Labelling Example** 本设备包含型号核准代码为 `：` CMIIT ID: 2021DJ14922(M) 的无线电发射模块。 Product Specification Rev. 1.6 Page 44 of 59 PAN1780 Bluetooth Module > 6 Regulatory and Certification Information ## Panasonic ## **6.1.8 Korea (Label Requirements)** Since the printable area on the PAN1780 is too small to show the KC logo and ID, this information is placed on the package and in the user information. The OEM must ensure KC marking requirements. The integrator of the module should refer to the labeling requirements for Korea available on the Korea Communications Commission (KCC) website. The module is not labeled with its own KC mark. The final product requires the KC mark and MSIP certificate number of the module. Format of the ID is as follows: “ **MSIP: R-R-Pid-PAN1780** ”, where: - **MSIP:** Ministry of Science, ICT & Future Planning - **R:** Indication of Broadcasting Communication Equipment code - **R:** Indication of Basic Registration Information - **Pid:** Indication of Application Information - **PAN1780:** Indication of Product ## **End Product Labelling Example** ## **R-R-Pid-PAN1780** The label of end product should indicate the RF approved module’s certification number as well as the end-device’s certification number. ## **For more details please visit:** Korea Communications Commission (KCC) http://www.kcc.go.kr National Radio Research Agency (RRA) http://rra.go.kr Product Specification Rev. 1.6 Page 45 of 59 INDUSTRY 6 Regulatory and Certification Information Panasonic - PAN1780 Bluetooth Module - > ## PAN1780 Bluetooth Module ## **6.1.9 Australia and New Zealand Conformity According to RCM** This Suppliers Declaration of Conformity (SDoC) is also valid for Australia. ## **6.1.9.1 Supplier’s Details** |**Name**|Microsystem Support Limited| |---|---| |**New Zealand (Physical Address)**|62 Heathcote Road| ||Castor Bay| ||Auckland 0620| |**New Zealand (Postal Address)**|PO Box 31-372| ||Milford| ||Auckland 0741| |**(New Zealand) Company**|256648| |**Number/GST Number**|| |**Supplier Number**|E7689| ## **New Zealand Contact Information** |**Telephone**|+ 64 9 4109286| |---|---| |**Mobile**|+ 64 27 4928152| |**Email**|mikefoxnz@gmail.com| ## **6.1.9.2 Conformity According to Section 134 (1) (g) of the New Zealand Radiocommunications Act 1989** ## **Product Details** |**Brand Name**|**Model**|**Description**|**Description**| |---|---|---|---| |Panasonic|PAN1780|Bluetooth 5 Low Energy (LE) Module 2 402 MHz to 2 480 MHz|Bluetooth 5 Low Energy (LE) Module 2 402 MHz to 2 480 MHz| All modules described in this Product Specification comply with the standards according to the following articles: |3.1a Safety/Health:|ETSI EN 62368-1: 2014/AC: 2015/A11: 2017| |---|---| ||ETSI EN 62479:2010| |3.1b EMC:|ETSI EN 301 489-1 V2.2.3| ||ETSI EN 301 489-17 V3.2.2 (Draft)| |3.2 Radio:|AS/NZS 4268| ||ETSI EN 300 328 V2.2.2| Product Specification Rev. 1.6 Page 46 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module ## ## **6.1.10 Bluetooth** The final Bluetooth end product listing needs to be created by using the following IDs: |**Bluetooth 5.1**|**Declaration ID**|**QDID**| |---|---|---| |End product|D050150|148922| |||| |**Bluetooth 5.3**|**Declaration ID**|**QDID**| |End product|D062277|188441| |||195971| ## **Bluetooth Marks** According to the Bluetooth SIG, the PAN1780 fulfills the criteria to label your product as a Bluetooth device: For further information please refer to the Bluetooth website www.bluetooth.com. Product Specification Rev. 1.6 Page 47 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module ## **6.2 For IEEE 802.15.4** ## **6.2.1 General Certification Information** Regulatory certifications are valid for the following radio relevant software: “nRF Connect SDK - libnrf-802154” (This library implements modulation according to the IEEE 802.15.4-2006 standard with a 250 kbps 2 450 MHz O-QPSK PHY.) Regulatory certifications stay valid for APPROTECT versions provided that: If the nRF52840 new silicon revision 3 with access port protection, which is implemented in the PAN1780 with Panasonic order number ENW89854A4KF is used: - Nordic IN141 Informational Notice v1.1 states “The new revision has no impact on CE, FCC/ISED or Bluetooth certifications unless the new pulse shaping filter is enabled.” - Nordic FTPAN-254 describes how to enable the pulse shaping filter, but as stated before it needs to remain disabled. Hence the code described in Nordic FTPAN-254 shall not be implemented/executed; otherwise the PAN1780 pre-certification becomes invalid. The Nordic FTPAN-254 workaround is meant for designs using an PA/LNA RF front end, which is not feasible with the PAN1780. Therefore, it is not useful to implement Nordic FTPAN-254. Due to the bandwidth of the IEEE 802.15.4 250 kbps 2 450 MHz O-QPSK PHY signal and the asymmetric placement of channels [11:26] in the 2.4 GHz ISM band by the IEEE 802.15.4 standard, it is necessary to limit the RF output power to 0 dBm in channel 26 to stay in compliance with the FCC/ISED band edge requirements. Allowed max RF output power to be adjusted by software: - Channel [11:25]: +8 dBm - • Channel [26]: +0 dBm For further certification requests for other radio software please contact Panasonic 7.2 Contact Details. Product Specification Rev. 1.6 Page 48 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module ## **6.2.2 Federal Communications Commission (FCC) for US** ## **6.2.2.1 FCC Notice** **==> picture [31 x 29] intentionally omitted <==** **----- Start of picture text -----**<br> @<br>**----- End of picture text -----**<br> The PAN1780 including the antennas, which are listed in 6.1.2.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ## **6.2.2.2 Caution** The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna, - Increase the separation between the equipment and receiver, - Connect the equipment into an outlet on a circuit different from that to which the receiver is - connected, - Consult the dealer or an experienced radio/TV technician for help. Product Specification Rev. 1.6 Page 49 of 59 PAN1780 Bluetooth Module > INDUSTRY Panasonic 6 Regulatory and Certification Information ## **6.2.2.3 Label Requirements** The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is **FCC ID: T7V1780** . This FCC identifier is valid for the PAN1780. The end product must in any case be labelled on the exterior with: "Contains FCC ID: T7V1780". Due to the PAN1780 model size, the FCC identifier is displayed in the installation instruction only and it cannot be displayed readable on the module’s label due to the limited size. ## **6.2.2.4 Antenna Warning** This antenna warning refers to the test device with the model number PAN1780 7.1 Ordering Information. The device is tested with a standard SMA connector and with the antenna listed below. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions. The FCC identifier for the device with the antenna listed in 6.1.2.5 Approved Antenna List is the same ( **FCC ID: T7V1780** ). ## **6.2.2.5 Approved Antenna List** |**Item**|**Part Number**|**Manufacturer**|**Frequency Band**|**Type**|**Max. Gain**<br>**(dBi)**| |---|---|---|---|---|---| |1 ANT016008LCS2442MA1 TDK|1 ANT016008LCS2442MA1 TDK|1 ANT016008LCS2442MA1 TDK|2.4 GHz|Chip antenna|-1| Product Specification Rev. 1.6 Page 50 of 59 PAN1780 Bluetooth Module > INDUSTRY Panasonic 6 Regulatory and Certification Information ## **6.2.2.6 RF Exposure** To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.2.5 Approved Antenna List. The preceding statement must be included as a “CAUTION” statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of the PAN1780 with a mounted ceramic antenna ( **FCC ID: T7V1780** ) is below the FCC radio frequency exposure limits. Nevertheless, the PAN1780 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. Product Specification Rev. 1.6 Page 51 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module - PAN1780 Bluetooth Module - > ## INDUSTRY Panasonic ## **6.2.3 Innovation, Science, and Economic Development (ISED) for Canada** ## **English** The PAN1780 is licensed to meet the regulatory requirements of ISED. License ID: **IC: 216Q-1780** HVIN: **ENW89854A1KF, ENW89854A4KF** Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in 6.1.2.5 Approved Antenna List, having a maximum gain of -1 dBi. Antennas not included in this list or having a gain greater than -1 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 Ω. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size, the IC identifier is displayed in the installation instruction only and it cannot be displayed on the module’s label due to the limited size. The end customer has to assure that the device has a distance of more than 10 mm from the human body under all circumstances. If the end customer application intends to use the PAN1780 in a distance smaller 10 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to ISED. ## **French** PAN1780 est garanti conforme aux dispositions règlementaires d’Industry Canada (ISED). License: **IC: 216Q-1780** HVIN: **ENW89854A1KF, ENW89854A4KF** Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique maximum autorisé. Des informations pour les utilisateurs sur la réglementation Canadienne concernant l’exposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. Product Specification Rev. 1.6 Page 52 of 59 6 Regulatory and Certification Information PAN1780 Bluetooth Module Ce produit a été développé pour fonctionner spécifiquement avec les antennes listées dans le tableau 6.1.2.5 Approved Antenna List, présentant un gain maximum de -1 dBi. Des antennes autres que celles listées ici, ou présentant un gain supérieur à -1 dBi ne doivent en aucune circonstance être utilisées en combinaison avec ce produit. L’impédance des antennes compatibles est 50 Ω. L’antenne utilisée avec ce produit ne doit ni être située à proximité d’une autre antenne ou d’un autre émetteur, ni être utilisée conjointement avec une autre antenne ou un autre émetteur. En raison de la taille du produit, l’identifiant IC est fourni dans le manuel d’installation. Le client final doit s'assurer que l'appareil se trouve en toutes circonstances à une distance de plus de 10 mm du corps humain. Si le client final envisage une application nécessitant d'utiliser le PAN1780 à une distance inférieure à 10 mm du corps humain, alors le FEO doit répéter l'évaluation DAS. L'équipement du client final doit répondre aux exigences actuelles de sécurité et de santé selon l’ISED. ## **6.2.3.1 IC Notice** ## **English** @ The device PAN1780 ( 7.1 Ordering Information), including the antennas ( 6.1.2.5 Approved Antenna List), complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ## **French** Le présent appareil PAN1780 ( 7.1 Ordering Information), les antennes y compris ( 6.1.2.5 Approved Antenna List), est conforme aux CNR-Gen d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage, et 2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Product Specification Rev. 1.6 Page 53 of 59 PAN1780 Bluetooth Module > 6 Regulatory and Certification Information ## Panasonic ## **6.2.3.2 Labeling Requirements** ## **English** @ ## **Labeling Requirements** The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is **IC: 216Q-1780** . This IC identifier is valid for all PAN1780 modules 7.1 Ordering Information. In any case, the end product must be labelled on the exterior with: "Contains IC: 216Q-1780”. ## **French** ## **Obligations d’étiquetage** Les fabricants d’équipements d’origine (FEO) – en anglais Original Equipment Manufacturer (OEM) – doivent s’assurer que les obligations d’étiquetage IC du produit final sont remplies. Ces obligations incluent une étiquette clairement visible à l’extérieur de l’emballage externe, comportant l’identifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. ## L’ identifiant IC est **IC: 216Q-1780** . Cet identifiant est valide pour tous les modules PAN1780 7.1 Ordering Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante: "Contient IC: 216Q-1780”. Product Specification Rev. 1.6 Page 54 of 59 > 6 Regulatory and Certification Information Panasonic - PAN1780 Bluetooth Module - > PAN1780 Bluetooth Module ## **6.2.4 European Conformity According to RED (2014/53/EU)** All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 3.1b EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) 3.2 Radio: EN 300 328 V2.2.2: (2019-07) - Due to the model size, the CE marking is displayed in the installation instruction only and it cannot be displayed conform to regulation (EU) No. 765/2008 in 5 mm height on the module’s label due to the limited space. - The RED EU Type Examination Certificate No. **T818666M** issued by the Notified Body 0682 can be used for the OEM end product conformity assessment. If a Notified Body has been contracted for the end product conformity assessment, it should be noted that this EU Type Examination Certificate should be used for conformance assessment. As a result of the conformity assessment procedure described in 2014/53/EU Directive, the end customer equipment should be labelled as follows: The requirements for CE marking are described in regulation (EC) No. 765/2008 Annex II. The end customer has to assure that the device has a distance of more than 5 mm from the human body under all circumstances. If the end customer application intends to use the PAN1780 in a distance smaller 5 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to RED. Further analysis must be conducted, as the addition of firmware and other functions requires the evaluation of additional threats and assets. PAN1780 and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra, and Turkey. Product Specification Rev. 1.6 Page 55 of 59 > 6 Regulatory and Certification Information Panasonic - PAN1780 Bluetooth Module - > PAN1780 Bluetooth Module ## **6.2.5 United Kingdom Conformity According to Statutory Instrument SI 2017/1206** All modules described in this Product Specification comply with the designated standards according to the following Regulations: Electrical Equipment (Safety) SI 2016/1101, EMC SI 2016/1091 together with Radio Equipment Regulation 2017 (RER) SI 2017/1206: Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) Radio: EN 300 328 V2.2.2: (2019-07) - Due to the model size, the UK marking is displayed in the installation instruction only and it cannot be displayed conform to SI 2017/1206 on the module’s label due to the limited space. - The RED EU Type Examination Certificate No. **T818666M** issued by the EU Notified Body 0682 can be used for the OEM end product conformity assessment. If a Notified Body has been contracted for the end product conformity assessment, it should be noted that this EU Type Examination Certificate should be used for conformance assessment. As a result of the conformity assessment procedure described in SI 2017/1206 Directive, the end customer equipment should be labelled as follows: ## ~~ee ee~~ ## **Restrictions or Requirements in the UK** The end customer has to assure that the device has a distance of more than 5 mm from the human body under all circumstances. If the end customer application intends to use the PAN1780 in a distance smaller 5 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to SI 2017/1206. PAN1780 and its model versions in the specified reference design can be used in the UK. Product Specification Rev. 1.6 Page 56 of 59 PAN1780 Bluetooth Module > INDUSTRY 6 Regulatory and Certification Information Panasonic ## **6.3 RoHS and REACH Declaration** The latest declaration of environmental compatibility (Restriction of Hazardous Substances, RoHS and Registration, Evaluation, Authorisation and Restriction of Chemicals, REACH) for supplied products can be found on the Panasonic website in the “Downloads” section of the respective product 7.2.2 Product Information. Product Specification Rev. 1.6 Page 57 of 59 INDUSTRY > PAN1780 Bluetooth Module Panasonic 7 Appendix INDUSTRY Panasonic 7 Appendix ## **7 Appendix** ## **7.1 Ordering Information** ## **Variants and Versions** |**Order Number**|**Brand Name**|**Description**|**MOQ5**| |---|---|---|---| |ENW89854A1KF6|PAN1780|Bluetooth Low Energy Module with Antenna<br>EmptyFlash|500| |ENW89854A4KF6|PAN1780|Bluetooth Low Energy Module with Antenna<br>Access Port Protection APPROTECT HW<br>Empty Flash|500| |ENW89854AUKF|PAN1780 EVB|Evaluation board with ENW89854A1KF|1| |ENW89854AQKF|PAN1780 EVB|Evaluation board with ENW89854A4KF|1| > 5 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. > 6 Samples available on customer demand Product Specification Rev. 1.6 Page 58 of 59 PAN1780 Bluetooth Module > INDUSTRY Panasonic 7 Appendix ## **7.2 Contact Details** ## **7.2.1 Contact Us** Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the **EU** , visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless.connectivity@eu.panasonic.com For Panasonic Sales assistance in **North America** , visit the Panasonic website “Sales & Support” to find assistance near you at https://na.industrial.panasonic.com/distributors For information about evaluation tools, schematics, software development, and more, please visit the “Panasonic Wireless Connectivity Development Hub” https://pideu.panasonic.de/development-hub/. ## **7.2.2 Product Information** Please refer to the Panasonic Wireless Connectivity website for further information on our products and related documents: For complete Panasonic product details in the **EU** , visit https://industry.panasonic.eu/ For complete Panasonic product details in **North America** , visit http://www.panasonic.com/rfmodules Product Specification Rev. 1.6 Page 59 of 59
Updated at April 28, 2026
Panasonic Industry is a global leader in the design and manufacture of high-quality electronic components. Renowned for a commitment to continuous innovation, the company provides the essential building blocks that empower modern engineering. From industrial automation to consumer electronics, Panasonic's components are trusted worldwide for their outstanding reliability, efficiency, and long-term performance. The extensive portfolio is anchored by a massive selection of passive components, featuring an industry-leading range of aluminium electrolytic, film, and polymer capacitors. Alongside these advanced capacitance solutions, engineers rely on Panasonic's robust power inductors and a highly versatile array of electromechanical devices, including solid-state, power, and signal relays engineered to excel in demanding environments. Beyond core passives and switching solutions, the offering encompasses critical circuit protection devices such as TVS varistors and NTC thermistors, as well as sophisticated thermal management materials. Panasonic also delivers precision light and motion sensors, highly reliable batteries, and advanced Bluetooth and WLAN connectivity modules, providing a comprehensive ecosystem of components to support next-generation technological design.
About Novapart
Novapart is a B2B electronic component broker specialising in stock shortages and cost reduction. We source hard-to-find parts and identify compliant alternatives across a catalogue of 410,000+ components from 500+ manufacturers.
Learn more →Stock Shortage Specialist
When a component is unavailable, discontinued or has an unacceptable lead time, we tap into our network of vetted European and Asian distributors to source what you need — without compromising on quality or traceability.
Request a quote →Compliant Alternatives
We identify pin-to-pin, electrically equivalent substitutes that meet the same certifications (RoHS, AEC-Q100, REACH) as your original specification — validated against datasheets, not just part numbers. Often at a lower cost.
BOM Analysis service →