EESX670A

**Slot-type Photomicrosensor (Non-modulated)** *1 **EE-SX47/67** 

CSM_EE-SX47/67_DS_E_13_2 

## **Global Standard Slot-type photomicrosensors with 50- to 100-mA direct switching capacity.** 

- Series includes models that enable switching between dark-ON and light-ON operation. 

- • Response frequency as high as 1 kHz. • Easy operation monitoring with bright light indicator. • Wide operating voltage range: 5 to 24 VDC • Models in which the light indicator turns ON for dark-ON operation are also available. 

- • A wide range of variations in eight different shapes. • Flexible robot cable is provided as a standard feature. *2 Be sure to read _Safety Precautions_ on page 5. ~~|~~ 

- ~~a~~ 

*1. Pre-wired Models are available only in the EE-SX67 Series. 

*2. Only for Pre-wired Models. 

+4 ony! For the most recent information on models that have been certified for safety standards, refer to your OMRON website. 

## **Ordering Information** 

|**Appearance**<br>~~ey~~|**Sensing**<br>**method**<br>~~ee~~|**Connect-**<br>**ing method**<br>~~ee~~|**Sensing distance**|**Sensing distance**|**Output**<br>**configuration**<br>~~Fr~~|**Indicator mode**<br>~~Fr~~|**Model**<br>~~Fr~~|**Model**<br>~~Fr~~|
|---|---|---|---|---|---|---|---|---|
||||||||**NPN output**<br>~~Fr~~|**PNP output**|
|Standard<br>~~ey~~|Through-<br>beam<br>type<br>(with slot)<br>~~ee~~<br>~~Mo~~|Connector<br>(4 poles)<br>~~ee~~<br>~~Mo~~|~~Mo~~|5 mm<br>(slot width)<br>~~Moo]~~|Dark-ON/Light-ON<br>(selectable)*3*4<br>~~Fr~~|Incident light<br>~~Fr~~|**EE-SX670**<br>~~Fr~~|**EE-SX670P**|
|||||||No incident light<br>~~Fr~~|**EE-SX670A**<br>~~Fr~~|**EE-SX670R**|
||||||Light-ON<br>~~Fr~~|Incident light<br>~~Fr~~|**EE-SX470**<br>~~Fr~~|---|
|L-shaped<br>~~ey~~<br>~~y-~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~Fr~~<br>~~**_**~~|Incident light<br>~~Fr~~<br>~~**_**—~~|**EE-SX671**<br>~~Fr~~<br>~~—~~|**EE-SX671P**|
|||||||No incident light<br>~~**_**—~~|**EE-SX671A**<br>~~—~~|**EE-SX671R**|
||||||Light-ON<br>~~**_**~~|Incident light<br>~~**_**—~~|**EE-SX471**<br>~~—~~|---|
|T-shaped,<br>slot center<br>7 mm<br>~~y-~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~**_**~~<br>~~—_f~~|Incident light<br>~~**_**—~~<br>~~—_f~~|**EE-SX672**<br>~~—~~<br>~~—_f~~|**EE-SX672P**|
|||||||No incident light<br>~~**_**—~~<br>~~—_f~~|**EE-SX672A**<br>~~—~~<br>~~—_f~~|**EE-SX672R**|
||||||Light-ON<br>~~**_**~~<br>~~—_f~~|Incident light<br>~~**_**—~~<br>~~—_f~~|**EE-SX472**<br>~~—~~<br>~~—_f~~|---|
|Close-<br>mounting<br>~~y-~~<br>~~Mo~~<br>~~¥~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~**_**~~<br>~~o]~~|Incident light<br>~~**_**—~~<br>~~o]~~|**EE-SX673**<br>~~—~~<br>~~o]~~|**EE-SX673P**|
|||||||No incident light<br>~~o]~~|**EE-SX673A**<br>~~o]~~|**EE-SX673R**|
||||~~Mo~~||Light-ON<br>~~o]~~<br>~~sr~~|Incident light<br>~~o]~~<br>~~sr~~|**EE-SX473**<br>~~o]~~|---|
||||~~Mo~~||||||
|Close-<br>mounting<br>~~Mo~~<br>~~¥~~<br>~~te~~<br>~~ai~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~o]~~<br>~~sr~~|Incident light<br>~~o]~~<br>~~sr~~|**EE-SX674**<br>~~o]~~|**EE-SX674P**|
|||||||No incident light<br>~~sr~~|**EE-SX674A**|**EE-SX674R**|
||||||Light-ON<br>~~sr~~<br>~~|~~|Incident light<br>~~sr~~<br>~~|~~<br>~~|~~|**EE-SX474**<br>~~|~~<br>~~|~~|---|
|T-shaped,<br>slot center<br>10 mm<br>~~¥~~<br>~~te~~<br>~~ai~~<br>~~y~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~sr~~<br>~~|~~|Incident light<br>~~sr~~<br>~~|~~<br>~~|~~<br>~~**|**~~|**EE-SX675**<br>~~|~~<br>~~|~~<br>~~**|**~~|**EE-SX675P**|
|F-shaped<br>~~te~~<br>~~ai~~<br>~~y~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~|~~<br>~~|~~|Incident light<br>~~|~~<br>~~|~~<br>~~|~~<br>~~**|**~~|**EE-SX676**<br>~~|~~<br>~~|~~<br>~~|~~<br>~~**|**~~|**EE-SX676P**|
|R-shaped<br>~~ai~~<br>~~y~~|||||Dark-ON/Light-ON<br>(selectable)*3*4<br>~~|~~|Incident light<br>~~|~~<br>~~**|**~~|**EE-SX677**<br>~~|~~<br>~~**|**~~|**EE-SX677P**|



*3. Dark-ON when the L terminal of the connector is opened, and light-ON when the L terminal and positive (+) terminal are connected. Do not connect the L terminal to 0 V when using dark-ON operation. When using light-ON, it is useful to select the connector EE-1001-1. The L terminal and positive (+) terminal of this connector are connected in advance. 

*4. If you do not use the L terminal wire ((2) pink) when you use a Connector with Cable for an EE-1006 or EE-1010-series Photomicrosensor, noise may affect the Photomicrosensor. To prevent the effects of noise, cut the unused L terminal wire at the base of the connector and wrap it with insulating tape to prevent it from coming in contact with other terminals. 

**1** 

**EE-SX47/67** 

## **Pre-wired Models** 

Infrared light 

|**Appearance**<br>~~de~~|**Sensing**<br>**method**|**Sensing distance**|**Sensing distance**|**Output**<br>**configura-**<br>**tion**|**Indicator**<br>**mode**|**Connecting**<br>**method**<br>~~—~~|**Model**|**Model**|
|---|---|---|---|---|---|---|---|---|
||||||||**NPN output**<br>~~—~~|**PNP output**|
|Standard<br>~~de~~|Through-<br>beam<br>type<br>(with slot)|~~_~~|5 mm<br>(slot width)|Dark-ON/<br>Light-ON<br>(selectable)<br>*1*2|Incident<br>light|Pre-wired<br>Models (1m)<br>~~—~~<br>~~oe~~<br>~~oe~~<br>~~oe~~<br>~~a~~<br>~~oe~~<br>~~oe~~<br>~~a~~|**EE-SX670-WR 1M **<br>~~—~~|**EE-SX670P-WR**<br>**1M**|
|L-shaped<br>~~de~~|||||||**EE-SX671-WR 1M **<br>~~—~~<br>~~oe~~|**EE-SX671P-WR**<br>**1M**|
|T-shaped,<br>slot center<br>7 mm<br>~~4~~|||||||**EE-SX672-WR 1M **<br>~~oe~~<br>~~oe~~|**EE-SX672P-WR**<br>**1M**|
|Close-<br>mounting<br>~~4~~<br>~~y~~|||||||**EE-SX673-WR 1M **<br>~~oe~~<br>~~oe~~|**EE-SX673P-WR**<br>**1M**|
|||~~_~~|||||||
|Close-<br>mounting<br>~~y~~<br>~~&~~<br>~~bb~~||~~_~~|||||**EE-SX674-WR 1M **<br>~~oe~~<br>~~a~~<br>~~oe~~|**EE-SX674P-WR**<br>**1M**|
|T-shaped,<br>slot center<br>10 mm<br>~~&~~<br>~~bb~~<br>~~r~~|||||||**EE-SX675-WR 1M **<br>~~a~~<br>~~oe~~<br>~~oe~~|**EE-SX675P-WR**<br>**1M**|
|F-shaped<br>~~bb~~<br>~~r~~|||||||**EE-SX676-WR 1M **<br>~~oe~~<br>~~oe~~|**EE-SX676P-WR**<br>**1M**|
|R-shaped<br>~~r~~<br>y|||||||**EE-SX677-WR 1M **<br>~~oe~~<br>~~a~~|**EE-SX677P-WR**<br>**1M**|



- *1. Dark-ON operation can be used when the L terminal is left unconnected or Light-ON operation can be used when the L terminal and positive (+) terminal are connected to each other. Do not connect the L terminal to 0 V when using dark-ON operation. 

- *2. If you do not use the L terminal wire ((2) pink) when you use a Connector with Cable for an EE-1006 or EE-1010-series Photomicrosensor, noise may affect the Photomicrosensor. To prevent the effects of noise, cut the unused L terminal wire at the base of the connector and wrap it with insulating tape to prevent it from coming in contact with other terminals. 

## **Accessories (Order Separately)   Connector Models** 

**Cable Type** ~~Pf~~ **length Model Remarks** Connector **EE-1001 EE-1001-1** L terminal and positive (+) terminal are already short-circuited. **EE-1009 * EE-1006 1M** 1 m **EE-1010 1M *** Connector with Cable **EE-1006 2M** 2 m **EE-1010 2M *** Connector with Robot 1 m **EE-1010-R 1M *** Cable 2 m **EE-1010-R 2M *** ~~}=~~ Applicable Photomicrosensors Connector Hold-down Clip **EE-1006A** For EE-SX670 @ and 470 @ only. (Can be used only with EE-1006 Connectors for the ~~oe~~ Photomicrosensors listed above.) 

Note: For details, refer to the Photomicro Sensors Accessories on EE- @ which can be accessed from your OMRON website. 

- EE-1009- or EE-1010-series Connectors have a builtin locking mechanism to prevent cable disconnection when only the cable is pulled. To remove the Connector from the Sensor, grip the top and bottom of the Connector firmly and push into the Sensor once before pulling out. The locking mechanism prevents the Connector from being removed by pulling on the cable only and enables removal only when the Connector (housing) is pulled. 

**2** omron ~~a~~ 

**EE-SX47/67** 

## **Ratings and Specifications** 

|**Item**||**Type**|**Standard**|**L-shaped**|**T-shaped,**<br>**slot center**<br>**7 mm**|**Close-mounting**|**Close-mounting**|**T-shaped,**<br>**slot center**<br>**10 mm**|**F-shaped**|**R-shaped**|
|---|---|---|---|---|---|---|---|---|---|---|
||**NPN**<br>**models**|**Connector**<br>**models**|**EE-SX670**<br>**EE-SX670A**<br>**EE-SX470**|**EE-SX671**<br>**EE-SX671A**<br>**EE-SX471**|**EE-SX672**<br>**EE-SX672A**<br>**EE-SX472**|**EE-SX673**<br>**EE-SX673A**<br>**EE-SX473**|**EE-SX674**<br>**EE-SX674A**<br>**EE-SX474**|**EE-SX675**|**EE-SX676**|**EE-SX677**|
|||**Pre-wired**<br>**models**|**EE-SX670-**<br>**WR**|**EE-SX671-**<br>**WR**|**EE-SX672-**<br>**WR**|**EE-SX673-**<br>**WR**|**EE-SX674-**<br>**WR**|**EE-SX675-**<br>**WR**|**EE-SX676-**<br>**WR**|**EE-SX677-**<br>**WR**|
||**PNP**<br>**models**|**Connector**<br>**models**|**EE-SX670P**<br>**EE-SX670R**|**EE-SX671P**<br>**EE-SX671R**|**EE-SX672P**<br>**EE-SX672R**|**EE-SX673P**<br>**EE-SX673R**|**EE-SX674P**<br>**EE-SX674R**|**EE-SX675P**|**EE-SX676P**|**EE-SX677P**|
|||**Pre-wired**<br>**models**|**EE-SX670P-**<br>**WR**|**EE-SX671P-**<br>**WR**|**EE-SX672P-**<br>**WR**|**EE-SX673P-**<br>**WR**|**EE-SX674P-**<br>**WR**|**EE-SX675P-**<br>**WR**|**EE-SX676P-**<br>**WR**|**EE-SX677P-**<br>**WR**|
|**Sensing distance**|||5 mm(slot width)||||||||
|**Sensing object**|||Opaque: 2×0.8 mm min.||||||||
|**Differential distance**|||0.025 mm||||||||
|**Light source**|||Infrared LED with apeak wavelength of 940 nm||||||||
|**Indicator*1**|||Light indicator(red) (turns ON when light is interrupted for models with A or R suffix)||||||||
|**Supply voltage**|||5 to 24 VDC ±10%, ripple(p-p): 10% max.||||||||
|**Current consumption**|||12 mA max.(Connector models, L terminal open), 35 mA max.(NPNpre-wired models), 30 mA max.(PNPpre-wired models)||||||||
|**Control output**|||NPN open collector: 5 to 24 VDC, 100 mA max.<br>100 mA load current with a residual voltage of 0.8 V max.<br>40 mA load current with a residual voltage of 0.4 V max.<br>OFF current (leakage current): 0.5 mA max.<br>PNP open collector: 5 to 24 VDC, 50 mA max.<br>50 mA load current with a residual voltage of 1.3 V max.<br>OFF current(leakage current): 0.5 mA max.||||||||
|**Protection circuits**|||Load short circuitprotection(Connector models), No circuitprotection(Pre-wired models)||||||||
|**Response frequency *2**|||1 kHz min.(3 kHz average)||||||||
|**Ambient illumination**|||1,000 lx max. with fluorescent light on the surface of the receiver.||||||||
|**Ambient temperature range**|||Operating:−25 to +55°C, Storage:−30 to +80°C(with no icingor condensation)||||||||
|**Ambient humidity range**|||Operating: 5% to 85%, Storage: 5% to 95%(with no icingor condensation)||||||||
|**Vibration resistance**|||Destruction: 20 to 2,000 Hz (peak acceleration: 100 m/s2)<br>1.5-mm double amplitude for 2 h(4-minperiods)each in X, Y, and Z directions||||||||
|**Shock resistance**|||Destruction: 500 m/s2for 3 times each in X, Y, and Z directions||||||||
|**Degree ofprotection**|||IEC60529 IP50||||||||
|**Connecting method**|||Connector Models (direct soldering possible), Pre-wired Models (Standard cable length: 1 m),<br>Models with Connectors(Standard cable length: 0.1 m)||||||||
|**Wei-**<br>**ght**|**Connector models**||Approx. 3.1g|Approx. 3g|Approx. 2.4g|Approx. 2.3g|Approx. 3g|Approx. 2.7g|Approx. 2.2g|Approx. 2.2g|
||**Pre-wired models**||Approx. 18.9g|Approx. 17.3g|Approx. 17.8g|Approx. 16.8g|Approx. 17.1g|Approx. 18.3g|Approx. 16.9g|Approx. 16.9g|
|**Ma-**<br>**teri-**<br>**al**|**Case**||Polybutylenephthalate(PBT)||||||||
||**Cover**||Polycarbonate||||||||
||**Emitter/receiver**||||||||||



*1. The indicator is a GaP red LED (peak wavelength: 690 nm). 

*2. The response frequency was measured by detecting the rotating disk shown at the right. 

**==> picture [143 x 51] intentionally omitted <==**

**----- Start of picture text -----**<br>
Disk<br>2.1 mm1 mm 1 mm<br>t = 0.2 mm<br>**----- End of picture text -----**<br>


**==> picture [539 x 34] intentionally omitted <==**

**3** 

**EE-SX47/67** 

## **Engineering Data (Reference Value)** 

**==> picture [513 x 236] intentionally omitted <==**

**----- Start of picture text -----**<br>
Sensing Position Characteristics Sensing Position Characteristics Repeated Sensing Position Characteristics<br>EE-SX47 @ /67 @ EE-SX47 @ /67 @ EE-SX47 @ /67 @<br>d<br>Dark-ON Dark-ON Dark-ON<br>Δd2<br>Δd3 Δd1<br>Δd4<br>d Δd5<br>d<br>Light-ON<br>Ta = −25°C Ta = 55°C Ta = 25°C<br>Light-ON0 1.0 2.0 3.0 4.0 5.0 6.0 Light-ON0 1.0 2.0 3.0 4.0 5.0 6.0 0  3.20  3.22  3.24  3.26  3.28<br>Distance d (mm) Distance d (mm) Distance d (mm)<br>Vcc =12 V, No. of repetitions: 20,  Δ d1 = 0.002 mm,<br>Δ d2 = 0.004 mm,  Δ d3 = 0.005 mm,  Δ d4 = 0.02 mm,<br>Δ d5 = 0.04 mm<br>Note: The data applies to dark status. Operation may<br>be affected by external light interference or light<br>coming through the sensing object.<br>**----- End of picture text -----**<br>


## **I/O Circuit Diagrams** 

## **NPN Output** 

**==> picture [512 x 369] intentionally omitted <==**

**----- Start of picture text -----**<br>
Model confiOutput guration Timing charts connectionsTerminal  Output circuit<br>Incident<br>Light indicatorInterruptedON Short-circuited  EE-SX67 @<br>Light-ON  (red)Output  OFFON L  terminal and between  EE-SX67 @ A<br>transistor OFF positive   terminal Light indicator  *<br>Load  Operates (red)<br>EE-SX67 @ (e.g., relay) Releases L  Load<br>EE-SX67 @ -WR Incident OUT  5 to<br>Dark-ON Light indicator(red) InterruptedOFFON Open between  L  terminal and  circuit Main   IC  (Control output) 100 mA max.  24 VDC<br>Output  ON positive   terminal<br>transistor OFF *1 *2<br>Load Operates *The terminal arrangement depends on the model.<br>(e.g., relay) Releases  Check the dimensional diagrams.<br>Incident EE-SX67 @ -WR<br>EE-SX670A Light-ON Light indicator(red)Output transistor InterruptedOFFOFFONON positive Short-circuited  L  terminal and between  terminal Light indicator(red) L * Load<br>EE-SX671AEE-SX672A (e.g., relay)Load ReleasesOperates circuitMain  OUTIC (Control output) 5 to 24 VDC<br>100 mA max.<br>EE-SX673A Incident<br>EE-SX674A Light indicatorInterruptedON Open between<br>Dark-ON (red)Output transistor OFFOFFON positive  L  terminal and *1 * terminal2 *The terminal arrangement depends on the model.  Check the dimensional diagrams.<br>Load  Operates<br>(e.g., relay) Releases<br>Incident Light indicator(red)<br>EE-SX470 Interrupted Load<br>EE-SX471 Light indicator ON<br>EE-SX472EE-SX473 Light-ON (red)Outputtransistor OFFOFFON --- circuitMain  OUTIC 5 to 24 VDC<br>EE-SX474 Load  Operates<br>(relay) Releases<br>**----- End of picture text -----**<br>


- *1. Do not connect the L terminal to 0 V when using dark-ON operation. 

- *2. If you do not use the L terminal wire ((2) pink) when you use a Connector with Cable for an EE-1006 or EE-1010-series Photomicrosensor, noise may affect the Photomicrosensor. To prevent the effects of noise, cut the unused L terminal wire at the base of the connector and wrap it with insulating tape to prevent it from coming in contact with other terminals. 

**==> picture [539 x 34] intentionally omitted <==**

**4** 

**EE-SX47/67** 

## **PNP Output** 

**==> picture [507 x 305] intentionally omitted <==**

**----- Start of picture text -----**<br>
Model confiOutput guration Timing charts connectionsTerminal  Output circuit<br>InterruptedIncident me<br>Light-ON Light indicator(red)Outputtransistor OFFOFFONON ommm positive  |° Short-circuited  L  terminal and between  terminal<br>Load Operates<br>EE-SX67 @ P (relay) Releases<br>EE-SX67 @ P-WR InterruptedIncident _<br>Light indicator ON Open between<br>Dark-ON (red)Outputtransistor OFFOFFON positive  L  terminal and *1 * terminal2 Light indicator(red) L *<br>Load Operates<br>(relay) Releases _ ‘ @ circuit { Main |_tt i oe: OUTIC 5 to 24 VDC<br>Incident = | se Load<br>Interrupted<br>Light indicator ON Short-circuited<br>Light-ON (red)Output  OFFON = L  terminal and between  Ee *The terminal arrangement depends on the model.  Check the dimensional diagrams.<br>transistor OFF mm positive  |° »o  terminal<br>EE-SX670R<br>EE-SX671R (e.g., relay)Load ReleasesOperates ome<br>EE-SX672R<br>EE-SX673R Incident<br>EE-SX674R Interrupted<br>Light indicator ON Open between<br>Dark-ON (red) OFF mM H o L  terminal and<br>Outputtransistor OFFON positive * @ 1 * terminal2<br>Load Operates<br>(e.g., relay) Releases<br>**----- End of picture text -----**<br>


- *1. Do not connect the L terminal to 0 V when using dark-ON operation. 

- *2. If you do not use the L terminal wire ((2) pink) when you use a Connector with Cable for an EE-1006 or EE-1010-series Photomicrosensor, noise may affect the Photomicrosensor. To prevent the effects of noise, cut the unused L terminal wire at the base of the connector and wrap it with insulating tape to prevent it from coming in contact with other terminals. 

## **Safety Precautions** 

## **Refer to** _**Warranty and Limitations of Liability**_ **.** 

## **WARNING** 

**This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes.** 

## **Precautions for Correct Use** ~~CO~~ 

Make sure that this product is used within the rated ambient environment conditions. 

## ● **Installation** 

- When direct soldering to the terminals, use the following guidelines. 

## **Precautions for Safe Use** 

## ● **Operating Environment** 

These Photomicrosensors have an IP50 (conforms to IEC) enclosure and do not have a water-proof or dust-proof structure. Therefore, do not use them in applications in which the sensor will be subjected to splashes from water, oil, or any other liquid. Liquid entering the Sensor may result in malfunction. 

Soldering Conditions **Item TemperPermissible Remarks ature time** Soldering iron 350°Cmax. 3 s max. The portion between the base of the terminals and the position 1.5 mm from the terminal base must not be soldered. ~~2~~ 

• The terminal base uses a polycarbonate resin, which could be deformed by excessive soldering heat, resulting in damage to the product's functionality. 

## ● **Lot Number and Model Number Legend** 

> In the following diagrams, 343U **EE-SX** @ **70** @ indicates the lot number and factory where the product was Model number manufactured. Do not include this EE-SX670 code with the model number when 343U ~~Ag~~ e ordering. The QR code on connector models is used by OMRON only. ~~iaka~~ l Lot number and factory code o 

**5** 

**EE-SX47/67** 

(Unit: mm) 

## **Dimensions** 

Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. 

## **Sensors** 

**==> picture [513 x 656] intentionally omitted <==**

**----- Start of picture text -----**<br>
EE-SX671/671P<br>EE-SX670/670P Terminal Arrangement<br>EE-SX671A/671R<br>EE-SX670A/670R Terminal Arrangement EE-SX471 (1) Vcc<br>EE-SX470 (1) Vcc (2) L L*<br>(2) L L* (3) OUT OUTPUT<br>(3) OUT OUTPUT (4) GND (0 V)<br>(4) GND (0 V) * Pin 2 is not used for the EE-SX471.<br>* Pin 2 is not used for the EE-SX470.<br>26.2<br>25.4 19 Four, R3.5<br>19<br>Two, 3.2 dia.<br>holes 3.2<br>6.95 14.5<br>3 Four, R1<br>3 4<br>Four, R1<br>13.419 6.40.8 6.2 3.8<br>5 Indicator window<br>1 2 3 4<br>2.54<br>9 Optical axis 2 1 133.4 6.35<br>0.8<br>13.8 5<br>8.4<br>13.2 5.5 Two, 3.8 dia. holes 9 8.3 9 Optical axisTwo, 3.2 dia. holes2.1 0.3 2 15.5<br>6.2 3.8 Indicator window 7.2 6.2 7.2<br>3.6 0.7<br>1 2 3 4<br>2.54 0.3 0.7 13 0.6 6.95<br>1 3.4<br>19<br>EE-SX672/672P EE-SX673/673P<br>EE-SX672A/672R Terminal Arrangement EE-SX673A/673R Terminal Arrangement<br>EE-SX472 (1) Vcc EE-SX473 (1) Vcc<br>(2) L L* (2) L L*<br>(3) OUT OUTPUT (3) OUT OUTPUT<br>(4) GND (0 V) (4) GND (0 V)<br>* Pin 2 is not used for the EE-SX472. * Pin 2 is not used for the EE-SX473.<br>1 3.7<br>3<br>26 6.4 1 2.6 6.3<br>12.8 (6.65)<br>3.5<br>Two, R1 7 Two, 3.2 dia. holes<br>7<br>0.8 1 3.4 1 3.4<br>0.8<br>2 5 5<br>9 Optical axisIndicator window 9 Optical axis 2<br>13 4.3 Four, R1.6 22.2 3 22.2 14.4<br>8.4<br>6.2 2.8<br>6.3 6.3<br>2.5 4.9<br>Four, R1<br>6.2 3.8 6.2 3.8 Indicator window<br>2.5<br>0.3 0.7 1 2 32.544 1 2 3 4 2.54 0.3 0.7<br>1 9 13<br>**----- End of picture text -----**<br>


**==> picture [539 x 34] intentionally omitted <==**

**6** 

**EE-SX47/67** 

**==> picture [253 x 83] intentionally omitted <==**

**----- Start of picture text -----**<br>
EE-SX674/674P<br>EE-SX674A/674R<br>EE-SX474 Terminal Arrangement<br>(1) Vcc<br>(2) L L**<br>(3) OUT OUTPUT<br>(4) GND (0 V)<br>* Pin 2 is not used for the EE-SX474.<br>**----- End of picture text -----**<br>


**EE-SX675/675P** 

**==> picture [482 x 294] intentionally omitted <==**

**----- Start of picture text -----**<br>
Terminal Arrangement Terminal Arrangement<br>(1) Vcc (1) Vcc<br>(2) L L** (2) L L<br>(3) OUT OUTPUT (3) OUT OUTPUT<br>(4) GND (0 V) (4) GND (0 V)<br>* Pin 2 is not used for the EE-SX474.<br>16.7<br>» ”<br>Optical axis 4<br>Two, R1 7 Two,  3.5 dia. holes 6.35 26<br>Indicator window<br>7 10<br>21.5 6.95<br>3 0.8 13.4<br>3 5 Optical axis<br>Sensing<br>6.2 3.8 window<br>9 Indicator window<br>1 2 3 4 2<br>CA 2.54 RED 13 Four, R3 = 3.7 Four, R1.6 1 4 F AR’<br>ye e08 135 0.8 0.1 ! 6 | 7 22.2 8.4 4 3<br>6.3<br>a (2.9) m7 Optical axis 2 ‘e _ E om 3.2 2.5 a oe<br>(9.3) 3.8<br>2.1 0.3 15.5 0.7 6.2<br>6.2 0.3 1 2 3 4<br>0.7 2.6 19.5 2.54<br>1 3<br>od 1 3.6 0.6 = 1 6.7<br>**----- End of picture text -----**<br>


**EE-SX676/676P** 

**EE-SX677/677P** 

**==> picture [490 x 297] intentionally omitted <==**

**----- Start of picture text -----**<br>
Terminal Arrangement Terminal Arrangement<br>(1) Vcc (1) Vcc<br>(2) L L (2) L L<br>(3) OUT OUTPUT (3) OUT OUTPUT<br>(4) GND (0 V) (4) GND (0 V)<br>uCURR yer<br>13.7<br>Optical axis 13.7<br>on i Optical axis<br>2.5<br>2.5<br>ediia 7 13.4 _ 13.27 6.35 _ 13.26.35 Sensing  window sd| 7<br>5 _ ~ 0.8 0.8 7 13.45<br>Optical axis Optical axis<br>9<br>Indicator window 9 2 2 9 9 Indicator window<br>ca ote LL rH<br>22.2 3 22.2 3<br>8.4 Sensing   8.4<br>13.6 7 window 7 13.6<br>2.5 2.5<br>6.2 3.8 3.3 3.3 6.2 3.8<br>a ig N B “A ae<br>1 2 3 4 0.3 0.3 1 2 3 4<br>S 600 2.54 Two, 3.5 dia. holes | 0.7 t 0.7 i Two, 3.5 dia. holes S 600 2.54<br>**----- End of picture text -----**<br>


**7** omrROnNn ~~a~~ 

**EE-SX47/67** 

## **EE-SX670-WR/670P-WR** 

**==> picture [102 x 8] intentionally omitted <==**

**----- Start of picture text -----**<br>
EE-SX671-WR/671P-WR<br>**----- End of picture text -----**<br>


**==> picture [503 x 658] intentionally omitted <==**

**----- Start of picture text -----**<br>
Terminal Arrangement Terminal Arrangement<br>Brown Vcc Brown Vcc<br>Pink L Pink L<br>Blue GND (0 V) Blue GND (0 V)<br>Black OUTPUT Black OUTPUT<br>26.2<br>Four, R1 Four, R3.5 19 Optical axis<br>Optical axis<br>6.95 3.2 6.95<br>3<br>19 Four, R1 18.7<br>3<br>Two, 3.2 dia. holes 4<br>Indicator window<br>25.4<br>ia 2<br>1 3.45 Optical axis 0.8 6.35<br>13.4 Robot cable of 2.8 dia., 4 cores,<br>(0.15 mm [2 ] with 0.8 mm dia. insulator);<br>9 2 Standard length: 1 m<br>11.2<br>int 1 6.35<br>13.8 Sensing  13.4<br>26.2 8.4 3 window 5 Optical axis Sensing window 0.8<br>11<br>2.5 5.5 9 2<br>SS B J 15.5 p A. 9 e 4.6 dia. 2.8 6.2 a<br>2 4.6 dia. Two, 3.8 dia. holes 7.2<br>— Indicator window Robot cable of 2.8 dia., 4 cores,  G | H 3.6 eréeie|T 19 Sseq 1)<br>(0.15 mm [2 ] with 0.8 mm dia. insulator); Two, 3.2 dia. holes<br>| Standard length: 1 m<br>EE-SX672-WR/672P-WR EE-SX673-WR/673P-WR<br>Terminal Arrangement Terminal Arrangement<br>Brown Vcc Brown Vcc<br>Pink L Pink L<br>Blue GND (0 V) Blue GND (0 V)<br>Black OUTPUT Black OUTPUT<br>13.7<br>7<br>Optical axis<br>12.6<br>6.3<br>Optical axis 12.8 | 3.5 ergy (6.65)<br>re ,<br>u 3 Four, R1 13.47 Two, 3.2 dia. holes<br>6.35 13.4 5 Optical axis 0.8<br>Sensing  0.8 5<br>window<br>Pru Optical axis +5 2 =<br>9<br>2<br>4.3 9 Indicator  14.4 2 dia. Sensing window<br>13 2.5 window 26.2<br>Four, R1.6 26.2 8.4<br>6.2 8.9 2.8 Indicator window<br>3<br>10.3 2.5<br>Four, R1<br>2 2 Robot cable of 2.8 dia., 4 cores,<br>(0.15 mm [2 ] with 0.8 mm dia. insulator);<br>Robot cable of 2.8 dia., 4 cores,  Standard length: 1 m<br>4.6 dia.<br>(0.15 mm [2 ] with 0.8 mm dia. insulator); 4.6 dia.<br>19 Standard length: 1 m<br>AK vin<br>26<br>**----- End of picture text -----**<br>


**8** omRON ~~a~~ 

**EE-SX47/67** 

**==> picture [553 x 763] intentionally omitted <==**

**----- Start of picture text -----**<br>
EE-SX674-WR/674P-WR EE-SX675-WR/675P-WR<br>Terminal Arrangement Terminal Arrangement<br>Brown Vcc Brown Vcc<br>Pink L Pink L<br>Blue GND(0V) Blue GND(0V)<br>Black OUTPUT Black OUTPUT<br>< =— be =—<br>Two, 3.5 dia. holes 7 Two, R1 Optical axis 1 0<br>6.35 26<br>7<br>7 4<br>6.95<br>25.7<br>Optical axis 3<br>3 19.5 1 3.4<br>0.8 Sensing  5<br>2 window Optical axis<br>Indicator window 2 9<br>Indicator window<br>Robot cable of 2.8 dia., 4 cores,  Four, R1.6 13<br>Al i (0.15 mm [2 ] with 0.8 mm dia. insulator); f o| ne 3<br>Standard length: 1 m 26.2 8.4<br>6 3.2<br>13.6<br>2.5<br>5 Optical axis Sensing window 0.8 3.7 10.3<br>Four, R3<br>(2.9) 2<br>AE 9 — 2 4.6 dia.<br>4.6 dia. 15.5<br>2.6 Robot cable of 2.8 dia., 4 cores,<br>6.2 2.8 (0.15 mm [2 ] with 0.8 mm dia. insulator); 13.4<br>Standard length: 1 m<br>16.7<br>EE-SX676-WR/676P-WR EE-SX677-WR/677P-WR<br>Terminal Arrangement Terminal Arrangement<br>Brown Vcc Brown Vcc<br>Pink L Pink L<br>Blue GND(0V) Blue GND(0V)<br>Black OUTPUT Black OUTPUT<br>- =— "f =—<br>Optical axis<br>2.5 Optical axis<br>2.5<br>7<br>13.7 7<br>“= 13.7<br>13.2 1 3.2<br>1 3.45 6.4 Sensing window 6.4 7 Sensing window 1 3.45 Optical axis<br>Optical axis 7<br>2<br>9 9 Indicator window<br>9 0.82 0.8 9<br>8.4 3 26.2 26.2 8.4 2.5 3<br>13 7 7 13<br>2.5 3.3<br>Indicator window 3.3 4 4<br>2 Two, 3.5 dia. holes Two, 3.5 dia. holes 2<br>waibs Robot cable of 2.8 dia., 4 cores,  Robot cable of 2.8 dia., 4 cores,<br>(0.15 mm [2 ] with 0.8 mm dia. insulator); (0.15 mm [2 ] with 0.8 mm dia. insulator);<br>ann 4.6 dia. Standard length: 1 m e 4.6 dia. ane Standard length: 1 m<br>9<br>omron a<br>**----- End of picture text -----**<br>


## Terms and Conditions Agreement 

## Read and understand this catalog. 

Please read and understand this catalog before purchasing the products.  Please consult your OMRON representative if you have any questions or comments. 

## Warranties. 

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. 

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE 

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. 

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. 

See http://www.omron.com/global/ or contact your Omron representative for published information. 

## Limitation on Liability; Etc. 

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. 

## Suitability of Use. 

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. 

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 

## Programmable Products. 

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. 

## Performance Data. 

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. 

## Change in Specifications. 

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. 

## Errors and Omissions. 

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 

**In the interest of product improvement, specifications are subject to change without notice.** 

## **OMRON Corporation** 

## **Industrial Automation Company** 

2017.7 

**http://www.ia.omron.com/** 

(c)Copyright OMRON Corporation 2017 All Right Reserved.