E3JM-DS70M4-US

**Built-in Power Supply Photoelectric Sensor E3JM** 

CSM_E3JM_DS_E_12_1 

## **Model Contribute to  Overall Cost Reduction** 

## **E3JM Terminal Block Models** 

- Easy to wire and adjust. 

For the most recent information on models that have been certified for safety standards, refer to your OMRON website. 

Be sure to read _Safety Precautions_ on page 7. ~~A~~ 

## **Ordering Information** 

**Sensors (Refer to** _**Dimensions**_ **on page 9.)** 

**==> picture [510 x 382] intentionally omitted <==**

**----- Start of picture text -----**<br>
Red light Infrared light<br>Sensing method Appearance Connectionmethod Sensing distance Operation mode configurationOutput Functions Model<br>E3JM-10M4-N<br>--- Emitter: E3JM-10L-N<br>Receiver: E3JM-10DM4-N<br>ee Relay<br>E3JM-10M4T-N<br>Through- Timer Emitter: E3JM-10L-N<br>beam Receiver: E3JM-10DM4T-N<br>(Emitter +  E3JM-10S4-N<br>Receiver) * 10 m --- Emitter: E3JM-10L-N<br>Receiver: E3JM-10DS4-N<br>Light-ON DC SSR<br>Terminal  Dark-ON E3JM-10S4T-N<br>block (switch  Timer Emitter: E3JM-10L-N<br>selectable) Receiver: E3JM-10DS4T-N<br>Retro- | --- E3JM-R4M4<br>Relay<br>reflective  Timer E3JM-R4M4T<br>with MSR  4 m --- E3JM-R4S4<br>function E39-R1 (provided) DC SSR Timer E3JM-R4S4T<br>--- E3JM-DS70M4<br>= a<br>Relay<br>Diffuse- Timer E3JM-DS70M4T<br>reflective 700 mm --- E3JM-DS70S4<br>DC SSR<br>7a —a Timer E3JM-DS70S4T<br>* Through-beam Sensors are sold in sets that include both the Emitter and Receiver. An order for the Emitter or Receiver alone cannot be accepted.<br>Note: UL-listed models have the -US suffix. The model number for an E3JM Through-beam Sensor ends in “-US” (and not in “-N”). (Example: E3JM-10M4-US).<br>Tightening nuts, washers, and rubber bushings are not provided with these models.<br>Change: Shape of the E3JM conduit socket<br>Accessories (Order Separately)<br>Slit  (A Slit is not provided with the Sensor for through-beam. Order a Slit separately if required.)   (Refer to  Dimensions  on page 9.)<br>Minimum detect-<br>Slit width Sensing distance able object Model Quantity Remarks<br>(reference value)<br>1 Slit each for<br>the Emitter and  (Seal-type long slit)<br>1 mm  ×  20 mm E3JM-10 @ 4(T)-N 1.2 m 1-mm dia. E39-S39 Can be used with the E3JM-10 @ 4(T)-N<br>Receiver (2 Slits  Models.<br>total)<br>**----- End of picture text -----**<br>


## **Reflectors  (A Reflector is required for each Retro-reflective Sensor.)** 

**The E39-R1 Reflector is provided with the Sensor. Order other Reflectors separately if required. (Refer to** _**Dimensions**_ **on** _**E39-L/E39-S/E39-R**_ **.)** 

|**Name**||**Sensing distance**|**Sensing distance**|||**Model**|**Quantity**|**Remarks**|
|---|---|---|---|---|---|---|---|---|
|Reflectors|E3JM-R4@4(T)|4(T)||4 m|4 m|**E39-R1**|1|Provided with the E3JM-R4@4(T)|



Note: Refer to _Reflectors_ on _E39-L/E39-S/E39-R_ for details. 

**1** omrRONn ~~a~~ 

**E3JM** 

## **Mounting Bracket** 

**Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required. (Refer to E39-L/E39-S/E39-R)** 

|**Appearance**|**Model**|**Quantity**|**Remarks**|
|---|---|---|---|
||**E39-L53**|1|Provided with the E3JM.|
||**E39-L51**|1|Mounting Bracket designed for changing<br>from he E3A-M, E3A2, E3A3, OA-5, or<br>OA-5N to the E3JM.|



- Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. Refer to _Mounting Brackets_ on _E39-L/E39-S/E39-R_ for details. 

**2** 

**E3JM** 

## **Ratings and Specifications** 

|**Sensing method**|**Sensing method**|**Through-beam model**|**Retro-reflective model**<br>**(with MSR function)**|**Diffuse-reflective model**|
|---|---|---|---|---|
|**Item**<br>**Model**||**E3JM-10**@**4(T)-N**|**E3JM-R4**@**4(T)**|**E3JM-DS70**@**4(T)**|
|**Sensing distance**||10 m|4 m (When using E39-R1)|White paper (200×200 mm):<br>700 mm|
|**Standard sensing object**||Opaque: 14.8-mm dia. min.|Opaque: 75-mm dia. min.|---|
|**Differential travel**||---||20% max. of sensing distance|
|**Directional angle**||Both Emitter and Receiver 3°to<br>20°|1°to 5°|---|
|**Light source (wavelength)**||Infrared LED (950 nm)|Red LED (660 nm)|Infrared LED (950 nm)|
|**Power supply voltage**||12 to 240 VDC±10%, ripple (p-p): 10% max.<br>24 to 240 VAC±10%, 50/60 Hz|||
|**Power con-**<br>**sumption**|**DC**|3 W max. (Emitter 1 W max.<br>Receiver 2 W max.)|2 W max.||
||**AC**|3 W max. (Emitter 1 W max.<br>Receiver 2 W max.)|2 W max.||
|**Control output**||Relay output (E3JM-@@M4 (T) model): SPDT, 250 VAC, 3A (cosφ=1) max., 5 VDC, 10 mA min.<br>DC SSR output (E3JM-@@S4 (T) model): 48 VDC, 100 mA max. (residual voltage: 2 V max.)<br>Light-ON/Dark-ON selectable|||
|**Life**<br>**expectancy**<br>**(relay output)**|**Mechanical**|50,000,000 times min. (switching frequency: 18,000 times/h)|||
||**Electrical**|100,000 times min. (switching frequency: 1,800 times/h)|||
|**Response time**|**Relay output**|(E3JM-@@M4 (T) models) Operate or reset: 30 ms max.|||
||**DC SSR output**|(E3JM-@@S4 (T) models) Operate or reset: 5 ms max.|||
|**Sensitivity adjustment**||---||One-turn adjuster|
|**Timer function***||ON-delay/OFF-delay/One-shot delay switch selectable<br>Delay time: 0.1 to 5 s (adjustable), only for E3JM-@@@4T|||
|**Ambient illumination**<br>**(Receiver side)**||Incandescent lamp: 3,000 lx max.|||
|**Ambient temperature range**||Operating:−25°C to 55°C, Storage:−30°C to 70°C (with no icing or condensation)|||
|**Ambient humidity range**||Operating: 45% to 85% (with no condensation), Storage: 35% to 95% (with no condensation)|||
|**Insulation resistance**||20 MΩmin. at 500 VDC|||
|**Dielectric strength**||2,000 VAC, 50/60 Hz for 1 min.|||
|**Vibration**<br>**resistance**|**Destruction**|10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions|||
||**Malfunction**|10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions|||
|**Shock**<br>**resistance**|**Destruction**|500 m/s23 times each in X, Y, and Z directions|||
||**Malfunction**|100 m/s23 times each in X, Y, and Z directions|||
|**Degree of protection**||IEC 60529: IP66|||
|**Connection method**||Terminal block|||
|**Weight (packed state)**||Approx. 270 g|Approx. 160 g||
|**Material**|**Case**|ABS (Acrylonitril Butadiene Styrene)|||
||**Lens**|Methacrylic resin|||
||**Cover**|Polycarbonate|||
||**Mounting**<br>**Bracket**|Iron|||
|**Accessories**||Mounting Bracket (with screw), Nuts, Terminal Protection Cover, One set of cable connection nuts (exclud-<br>ing -US Models), Instruction manual, Reflector (E39-R1: only for Retro-reflective Sensors)|||



*The timer cannot be disabled for models with timer functions (E3JM-@@@4T). 

**3** 

**E3JM** 

**Engineering Data (Reference Value)** 

## **Parallel Operating Range** 

## **Through-beam E3JM-10** @ **4(T)-N** 

## **Retro-reflective** 

**Through-beam** 

**E3JM-10** @ **4(T)-N + E39-S39 (Optional Slit) E3JM-R4** @ **4(T) + E39-R1 (A Slit is mounted to the Emitter and Receiver.) (Supplied Reflector)** 

**==> picture [511 x 546] intentionally omitted <==**

**----- Start of picture text -----**<br>
600 60 150 Reflector: E39-R1<br>Y<br>400 40 100<br>X<br>200 20 50<br>0 0 0<br>2 4 6 8 10 12 14 16 0.5 1 1.5 2 2.5 3 3.5 1 2 3 4 5 6 7 8<br>Distance X (m) Distance<br>−200 −20 Distance  −50 X (m)<br>X (m)<br>−400 Y −40 −100 Y<br>−600 X −60 −150 X<br>Operating Range<br>Diffuse-reflective<br>E3JM-DS70 @ 4(T)<br>60 Sensing object: 200 × 200 mm<br>50 Y<br>40<br>X<br>30<br>20<br>10<br>0<br>2 4 6 8 10<br>−10 Distance<br>−20 X (m)<br>−30 White paper<br>Black carbon<br>−40 SUS (Luster)<br>Aluminum foil<br>−50 (No luster on<br>−60 the back)<br>Excess Gain Ratio vs. Set Distance<br>Through-beam Retro-reflective<br>E3JM-10 @ 4(T)-N E3JM-R4 @ 4(T) + E39-R1  E3JM-R4 @ 4(T) + E39-R3<br>(Supplied Reflector) (Optional Reflector)<br>1,000 1,000 Reflector: E39-R1 1,000 Reflector: E39-R3<br>500 500 500<br>300<br>100 100 100<br>50 50 50<br>30<br>10 10 10<br>5 5 5<br>3<br>Operating  level 1 Operating   1 Operating  1<br>level level<br>0.5 0.5 0.5<br>0.3<br>0.1 0.1 0.1<br>0 2 4 6 8 10 12 14 16 18 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9<br>Distance (m) Distance (m) Distance (m)<br>Distance Y (mm) Distance Y (mm) Distance Y (mm)<br>Distance Y (mm)<br>Excess gain ratio Excess gain ratio Excess gain ratio<br>**----- End of picture text -----**<br>


**4** 

**E3JM** 

**==> picture [330 x 207] intentionally omitted <==**

**----- Start of picture text -----**<br>
Sensing Object Size vs. Sensing Distance<br>Diffuse-reflective<br>E3JM-DS70 @ 4(T) E3JM-DS70 @ 4(T)<br>1,000 Sensing object:   12<br>500 white paper 200 × 200 mm<br>10<br>100<br>50 8 White paper<br>Black carbon<br>SUS (Luster)<br>10 6 Aluminum foil<br>(No luster on<br>5 the back)<br>4<br>Operating  1<br>level<br>0.5 2<br>0.1<br>0 100 200 300 400 500 600 700 800 900 0 20 40 60 80 100 120 140 160 180 200 220<br>Distance (mm) Side length of sensing object (mm)<br>Excess gain ratio Distance (m)<br>**----- End of picture text -----**<br>


## **Sensing Object Size vs. Sensing Distance** 

## **Diffuse-reflective** 

## **E3JM-DS70** @ **4(T)** 

**5** 

**E3JM** 

**I/O Circuit Diagrams** 

## **Relay Output Models** 

**==> picture [511 x 111] intentionally omitted <==**

**----- Start of picture text -----**<br>
Model Timing chart Output circuit<br>24 to 240 VAC<br>Incident light 12 to 240 VDC<br>E3JM-10M4(T)-N *1 No incident lightIndicator(red) *2 OFFON Photoelectric Sensor main circuit 12 No polaritySourcePower<br>E3JM-R4M4(T) ON 3 Tb<br>L-ON (Ta) OFF 4 Tc Contact output<br>E3JM-DS70M4(T) D-ON (Ta) ON 5 Ta<br>OFF<br>Refer to page 7 for information on Sensors with timers (T). (Built-in Relay: G6C)<br>**----- End of picture text -----**<br>


## **DC SSR Output Models** 

**==> picture [511 x 160] intentionally omitted <==**

**----- Start of picture text -----**<br>
Model Timing chart Output circuit<br>24 to 240 VAC<br>12 to 240 VDC<br>1 SourcePower<br>No polarity<br>Incident light<br>E3JM-10S4(T)-N *1 No incident lightIndicator ON 2<br>(red) *2 OFF L/ON 3 Load<br>E3JM-R4S4(T) L-ON (Ta) OFFON CircuitDrive  NO I1<br>E3JM-DS70S4(T) D-ON (Ta) ON  D/ON 5 Load 48 VDC<br>OFF Photo- Drive  NC max.<br>Refer to page 7 for information on Sensors with timers (T). electric Sensor  Circuit I2<br>main<br>circuit I1+I2<100 mA<br>4<br>COM<br>**----- End of picture text -----**<br>


Note: Connect terminal 1 to any polarity and terminal 2 to the power supply because there is no polarity on the Emitter side. 

- *1. Models numbers for Through-beam Sensors (E3JM-10@4(T)-N) are for sets that include both the Emitter and Receiver. 

The model number of the Emitter is always E3JM-10L-N. Add a “D” to get the model number of the Receiver (example: E3JM-10DM4-N). Confirm the model numbers of the Emitter and Receiver in _Ordering Information_ . 

- *2. This is the light indicator on Sensors without a timer and the operation indicator on Sensors with a timer. 

**6** 

**E3JM** 

## **Safety Precautions** 

## **Refer to** _**Warranty and Limitations of Liability**_ **.** 

## **WARNING** 

**This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes.** 

## **Precautions for Correct Use** 

Do not use the product in atmospheres or environments that exceed product ratings. 

## ● **Designing** 

**==> picture [512 x 208] intentionally omitted <==**

**----- Start of picture text -----**<br>
Operation Note:  The white part of the DIP switch indicates which setting is selected.<br>Switch<br>configuration Switch selection Timing charts<br>Models  D·ONMODE0    1 L·ON D·ONMODE0    1 L·ON Light-ON, Relay ON,DC output switching No incident lightIncident light<br>without timer Operation  D·ONMODE0    1 L·ON element ONDark-ON, Relay ONDC output switching DL··ONON OFF ON ON<br>selector element ON OFF<br>ON-delay OFF-delay One-shot delay ON-delay OFF-delay One-shot delay<br>MODE0    1 MODE0    1 MODE0    1 MODE0    1<br>D·ON L·ON D·ON L·ON D·ON L·ON D·ON L·ON<br>Models with timer TIMEROperation SelectorSelector switch for  SW1SW2 TIMERBoth SW1 and SW2 at  "0."SW1SW2 TIMEROnly SW2 at  "1."SW1SW2 TIMEROnly SW1 at  "1," which overrides either setting of SW2.SW1SW2 No incident lightIncident lightLD··ONONOFF OFFON ON  T T No incident lightIncident lightLD··ONONOFF OFFON ON T T No incident lightIncident lightLD··ONONOFF OFFON ON  T T<br>timer mode Note: The operation selector is the same as that for models<br>without a timer.<br>**----- End of picture text -----**<br>


## **Output Relay Contact** 

If E3JM is connected to a load with contacts that spark when the load is turned OFF (e.g., a contactor or valve), the normally-closed side may be turned ON before the normally-open side is turned OFF or vice-versa. If both normally-open output and normally-closed output are used simultaneously, apply an surge suppressor to the load. 

Refer to _OMRON’s PCB Relays Catalog_ (X33) for typical examples of surge suppressors. 

**7** 

**E3JM** 

## ● **Wiring** 

## **Connecting and Wiring** 

- We recommend connecting a cable with a conductor cross-section of 0.3 mm[2] and an outer diameter of 6 to 8 mm. 

- Be sure to firmly tighten the cover in order to maintain waterproof and dustproof properties. The screw size of the conduit sockets is shown in the following table. 

|**Model**|**Conduit socket thread size**|
|---|---|
|E3JM-@|PF1/2|



- When using the DC SSR output model, the total of the load current for the Light-ON output (NO) and that for the Dark-ON (NC) should be 100 mA max. If the total exceeds 100 mA, the load short-circuit protection function will be activated (this function will be reset when the power of the Photoelectric Sensor is turned OFF). 

## ● **Others** 

## **Terminal Protection Cover (Provided)** 

The terminal protection cover is designed to improve safety by maintaining the sensitivity properties of the product and by preventing any contact with charged sections while it is being operated with the mode set to the timer mode. Mount the product as shown in the following diagram (mount the Through-beam Model on the Receiver side). 

**==> picture [91 x 17] intentionally omitted <==**

**----- Start of picture text -----**<br>
Terminal protection cover<br>E3JM<br>**----- End of picture text -----**<br>


## **Cable End Treatment** 

Adjust the four wires to the same length when the Ta output is to be used only. If both the Ta and Tb outputs are to be used, treat them as shown in the following diagram. 

**==> picture [75 x 35] intentionally omitted <==**

## **Recommended example** 

**==> picture [239 x 97] intentionally omitted <==**

**----- Start of picture text -----**<br>
A pprox.<br>45 mm<br>Power<br>source<br>Tc, Ta<br>Tb<br>Rubber bushing (provided)*<br>A pprox. Washer (provided)*<br>55 mm Tightening nut (provided)*<br>**----- End of picture text -----**<br>


## **Ambient Conditions (Installation Area)** 

The E3JM will malfunction if installed in the following places. 

   - Places where the E3JM is exposed to a dusty environment. 

   - Places where corrosive gases are produced. 

- These parts are not provided with models with a -US suffix. 

## **Recommended Crimp Terminal Dimensions (Unit: mm)** 

||||**Round**|**Round**|**type**|**type**||**Fork type**|**Fork type**|**Fork type**|
|---|---|---|---|---|---|---|---|---|---|---|
|7|||||~~1~~0 max~~.~~|||~~1~~0 max~~.~~<br>~~1~~9 max~~.~~<br>. min.<br>7 max.<br>(After crimping)|||
||max.|||||7 max|.<br>7 max.||||
||||in.||||||||
||3.6 dia. m||||9 max~~.~~<br>(After crimping)||<br>3.6 dia||||
||||||||||||



**==> picture [66 x 31] intentionally omitted <==**

**----- Start of picture text -----**<br>
Emitter<br>Receiver<br>**----- End of picture text -----**<br>


   - Places where the E3JM is directly exposed to water, oil, or chemicals. 

- Note: Use terminals with insulation tube (recommended crimp terminal: 1.25 to 3.5). 

**==> picture [59 x 29] intentionally omitted <==**

**----- Start of picture text -----**<br>
Emitter<br>Receiver<br>**----- End of picture text -----**<br>


**8** 

**E3JM** 

(Unit: mm) 

Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. 

## **Dimensions** 

## **Sensors** 

**==> picture [511 x 307] intentionally omitted <==**

**----- Start of picture text -----**<br>
E3JM-10 @ 4(T)-N * E3JM-R4 @ 4(T)<br>E3JM-DS70 @ 4(T)<br>With Mounting Bracket Attached With Mounting Bracket Attached<br>8 8<br>24.5 6 24.5 6<br>22 6.4 6 (12.4) 22 6.4 6 (12.4)<br>6 dia. 6 dia.<br>12.4 18 6 12.4 18 6<br>39.5 39.5<br>Emitter: E3JM-10L-N<br>Receiver: E3JM-10D@4 (T) -N 75 75<br>25 4.1 11.5 Indicator *165 25 4.1 11.5 Indicator *165<br>Lens: 14.8 dia. 3 3<br>Emitter<br>80 65 Optical axisTwo, M4×30 80 65 Receiver Two, M4 × 30<br>15 44(A) *2 1.6 9 20 JIS B 0202PF1/2 15 47.5(A) *2 1.6 9 20 JIS B 0202PF1/2<br>Mounting Holes Steel 5 54.540 Hexagonal nut  (Diagonal: 22) Applicable cable:  Mounting Holes Steel 5 54.540 Hexagonal nut  (Diagonal: 22) Applicable cable:6 to 8 dia.<br>Two, M6 *1. Emitter: Power indicator 6 to 8 dia. Two, M6<br>     Receiver: Light indicator (without timer function) *1. Light indicator (without timer function)<br>     Operation indicator (with timer function)      Operation indicator (with timer function)<br>42 *2. Mounting Brackets can be used on the A side. 42 *2. Mounting Brackets can be used on the A side.<br>Note: The operating mode switch and timer  Note: The operating mode switch, timer mode switch, and<br>mode switch are located inside the cover. sensitivity adjuster (sensitivity adjuster: E3JM-<br>DS70@4(T) only) are located inside the cover.<br>**----- End of picture text -----**<br>


- Models numbers for Through-beam Sensors (E3JM-10@4(T)-N) are for sets that include both the Emitter and Receiver. The model number of the Emitter is always E3JM-10L-N. Add a “D” to get the model number of the Receiver (example: EE3JM-10DM4-N). Confirm the model numbers of the Emitter and Receiver in _Ordering Information_ . 

## **Accessories (Order separately)** 

**==> picture [173 x 66] intentionally omitted <==**

**----- Start of picture text -----**<br>
Seal-type Long Slit<br>E39-S39<br>14<br>1± [0.1]<br>20 26.5<br>Materials: Polyester<br>0.1-mm thick<br>**----- End of picture text -----**<br>


## **Mounting Brackets** 

Refer to _E39-L/E39-S/E39-R_ for details. 

**9** 

## Terms and Conditions Agreement 

## Read and understand this catalog. 

Please read and understand this catalog before purchasing the products.  Please consult your OMRON representative if you have any questions or comments. 

## Warranties. 

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. 

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE 

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. 

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. 

See http://www.omron.com/global/ or contact your Omron representative for published information. 

## Limitation on Liability; Etc. 

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. 

## Suitability of Use. 

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. 

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 

## Programmable Products. 

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. 

## Performance Data. 

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. 

## Change in Specifications. 

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. 

## Errors and Omissions. 

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 

2016.12 

**In the interest of product improvement, specifications are subject to change without notice.** 

## **OMRON Corporation** 

## **Industrial Automation Company** 

**http://www.ia.omron.com/** 

(c)Copyright OMRON Corporation 2016 All Right Reserved.