DP-1011-01A

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **DP-1011-01A Datasheet** 

## **1 Introduction** 

## **1.1 Features** 

The DP-1011-01A is a 10.1-inch TFT-LCD module featuring a resolution of 1280 × 800 pixels. The module integrates a TFT-LCD panel, driver ICs, flexible printed circuit (FPC), backlight unit, and a capacitive touch panel (CTP). 

Powered by HX8288 and HX8695 display drivers, it delivers 16.7 million colors over a single-channel LVDS interface, providing stable and high-speed image transmission. Touch input is handled by the GT928 controller with I²C interface support, enabling smooth and responsive touch functionality. GT928 supports up to 10-point touches. 

- 10.1" TFT-LCD with 1280 × 800 resolution and CTP support 

- 16.7M RGB colors for vivid display 

- Single-channel LVDS interface for highspeed, reliable data transfer 

- Integrated GT928 touch controller with I²C interface providing accurate and low-latency capacitive touch response 

- Meets RoHS requirements for environmental compliance 

Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Bridgetek Pte Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Bridgetek Pte Ltd, 1 Tai Seng Avenue, #03-05, Singapore 4536464. Singapore Registered Company Number: 201542387H 

Copyright © Bridgetek Pte Ltd 

1 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **2 Part Numbers/Ordering Information** 

|**Part No.**|**Description**|
|---|---|
|DP-1011-01A|TFT Display 10.1 inch (1280 x 800 resolution) with Capacitive Touch<br>Panel– Outline 250mm x 173mm|



Copyright © Bridgetek Pte Ltd 

2 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

|**Contents**|
|---|
|**1** **Introduction ............................................................1**|
|**1.1**<br>**Features ......................................................................... 1**|
|**2** **Part Numbers/Ordering Information ......................2**|
|**3** **General Specifications .............................................5**|
|**4** **Hardware Description .............................................6**|
|**4.1**<br>**Pin Assignment .............................................................. 6**|
|4.1.1<br>TFT-LCD Interface Pin Assignment .................................................. 6|
|4.1.2<br>CTP Interface Pin Assignment ........................................................ 7|
|**5** **Specifications ..........................................................8**|
|**5.1**<br>**Absolute Maximum Ratings ............................................ 8**|
|5.1.1<br>Electrical Absolute Maximum Ratings .............................................. 8|
|5.1.2<br>Environmental Absolute Maximum Ratings ...................................... 8|
|**5.2**<br>**Electrical Specifications .................................................. 9**|
|5.2.1<br>Electrical Characteristics ............................................................... 9|
|5.2.2<br>Current Consumption .................................................................... 9|
|5.2.3<br>LED Backlight Specification ........................................................... 10|
|5.2.4<br>AC Electrical Characteristics .......................................................... 10|
|**5.3**<br>**Timing .......................................................................... 11**|
|5.3.1<br>Input Timing Characteristics ......................................................... 11|
|5.3.2<br>LVDS Data Input Format .............................................................. 12|
|**5.4**<br>**Power Sequence ........................................................... 12**|
|5.4.1<br>Power ON Sequence .................................................................... 12|
|5.4.2<br>Power OFF Sequence ................................................................... 13|
|**5.5**<br>**Optical Specifications ................................................... 14**|
|**6** **Reliability Test Items ............................................ 17**|
|**7** **Dimension ............................................................. 18**|
|**8** **Disclaimer Notice: Use of Third-Party Software or**|
|**Websites ................................................................... 19**|



Copyright © Bridgetek Pte Ltd 

3 

**DP-1011-01A Datasheet Version 1.0** 

**==> picture [458 x 227] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||
|---|---|
|Document Reference No.: BRT_000477   Clearance No.: BRT#242|
|9|Warranty Statement ............................................. 20|
|10|Contact Information ........................................... 21|
|Appendix A – References ........................................... 22|
|Document References ........................................................... 22|
|Acronyms and Abbreviations ................................................ 22|
|Appendix B – List of Tables & Figures........................ 23|
|List of Tables ........................................................................ 23|
|List of Figures ....................................................................... 23|
|Appendix C – Revision History ................................... 24|

**----- End of picture text -----**<br>


Copyright © Bridgetek Pte Ltd 

4 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **3 General Specifications** 

|**Item**|**Specification**|**Unit**|**Note**|
|---|---|---|---|
|LCD Type|TFT|-||
|LCD Size|10.1|inch||
|Number of Pixels|1280(H)x 800(V)|pixels||
|Viewing Direction|All|o’clock||
|Interface|Single-channel LVDS|||
|Display Colors|16.7M Colors (RGB 8 bit)|colors|Note 2|
|Module Size|250(H)x 173(V)x 7.1(D)|mm|Note 3|
|ActiveArea|216.96(H)x 135.60(V)|mm||
|Brightness|700|cd/m2|Typical value|
|Display Driver IC|HX8288*4 & HX8695*1|-||
|Touch Panel|CapacitiveTouch Panel|-||
|Touch Driver IC|GT928|-||
|CTP Structure|G + G|-||
|CTP Connection Type|FPC|||
|Operation Temperature|0~50°C|°C||
|Storage Temperature|-20~60°C|°C||



**Table 2 - General Specifications** 

## **Note:** 

1. Complies with environmental protection requirements and is RoHS compliant. 2. Color tune is slightly changed by temperature and driving voltage. 

3. Module size excludes FPC and solder; with CTP. 

Copyright © Bridgetek Pte Ltd 

5 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **4 Hardware Description** 

The DP-1011-01A features a 10.1-inch TFT-LCD with a 1280 × 800 resolution, integrated with a capacitive touch panel directly bonded to the LCD. 

## **4.1 Pin Assignment** 

The interface connector pin configurations are described in the following sections. 

## **4.1.1 TFT-LCD Interface Pin Assignment** 

|**Pin no**|**Symbol**|**Type**|**Description**|
|---|---|---|---|
|1|VCOM|P|Common voltage|
|2|VDD|P|Power for digital circuit|
|3|VDD|P|Power for digital circuit|
|4|NC|-|No Connection|
|5|NC|-|No Connection|
|6|NC|-|No Connection|
|7|GND|P|Ground|
|8|RXIN0-|I|-LVDS differential data input|
|9|RXIN0+|I|+LVDS differential data input|
|10|GND|P|Ground|
|11|RXIN1-|I|-LVDS differential data input|
|12|RXIN1+|I|+LVDS differential data input|
|13|GND|P|Ground|
|14|RXIN2-|I|-LVDS differential data input|
|15|RXIN2+|I|+LVDS differential data input|
|16|GND|P|Ground|
|17|RXCLKIN-|I|-LVDS differential clock input|
|18|RXCLKIN+|I|+LVDS differential clock input|
|19|GND|P|Ground|
|20|RXIN3-|I|-LVDS differential data input|
|21|RXIN3+|I|+LVDS differential data input|
|22|GND|P|Ground|
|23|NC|-|No Connection|
|24|NC|-|No Connection|
|25|GND|P|Ground|
|26|NC|-|No Connection|
|27|LED_PWM|O|Blacklight CABC controller signal output|
|28|NC|-|No Connection|
|29|AVDD|P|Power for analogcircuit|
|30|GND|P|Ground|
|31|LED-|P|LED Cathode|
|32|LED-|P|LED Cathode|
|33|NC|-|No Connection|
|34|NC|-|No Connection|



Copyright © Bridgetek Pte Ltd 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

|35|VGL|P|Negativepower for TFT|
|---|---|---|---|
|36|NC|-|No Connection|
|37|CABC_EN|I|CABC Enable Input|
|38|VGH|P|Positivepower for TFT|
|39|LED+|P|LED Anode|
|40|LED+|P|LED Anode|



**Table 3 - TFT-LCD Interface Pin Definition** 

## **4.1.2 CTP Interface Pin Assignment** 

## **I2C Interface Pin Definition, connector: FPC 0.5mm pitch 10pin** 

|**Pin no**|**Name**|**Type**|**Description**|
|---|---|---|---|
|1|GND|P|Ground|
|2|GND|P|Ground|
|3|VDD_CTP|P|3.3V Inputpower supply|
|4|VDD_CTP|P|3.3V Inputpower supply|
|5|SCL|I/O|I2C serial bus,clock line(3.3V)|
|6|SDA|I/O|I2C serial bus,data line(3.3V)|
|7|RES|I|Reset input,active “L”(3.3V)|
|8|INT|O|Interrupt request to the host(3.3V)|
|9|GND|P|Ground|
|10|GND|P|Ground|



**Table 4 - CTP Interface Pin Definition** 

Copyright © Bridgetek Pte Ltd 

7 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **5 Specifications** 

## **5.1 Absolute Maximum Ratings** 

## **5.1.1 Electrical Absolute Maximum Ratings** 

Condition: VSS=0V, Ta=25°C 

|Condition: VSS=0V, Ta=25°CSS=0V, Ta=25°C=0V, Ta=25°C0V, Ta=25°Ca=25°C=25°C25°C°CC||||||
|---|---|---|---|---|---|
|**Item **|**Symbol **|**MIN.**|**MAX.**|**Unit**|**Note**|
|Power Supply Voltage|VDD|-0.3|3.9|V|Note 1,2|
||VDD_CTP|0.3|3.47|V||
||AVDD|0.5|14.0|V||
||VGH|-0.3|42.0|V||
||VGL|-19.0|0.3|V||



**Table 5 - Electrical Absolute Maximum Ratings** 

## **Note:** 

1. Permanent damage to the LCD module may occur if operated beyond the specified limits. Operation beyond the specified electrical characteristics may lead to malfunction or reduced reliability. 

2. VDD must always be greater than VSS. 

3. Ensure proper grounding when handling the LCD module. 

## **5.1.2 Environmental Absolute Maximum Ratings** 

|**Item**|**Storage**|**Storage**|**Operating**|**Operating**|**Note**|
|---|---|---|---|---|---|
||**MIN.**|**MAX.**|**MIN.**|**MAX.**||
|Ambient Temperature|-20°C|60°C|0°C|50°C|Note 1,2|
|Humidity|-|-|-|-|Note 3|



**Table 6 - Environmental Absolute Maximum Ratings** 

## **Note:** 

1. Response time decreases at low operating temperatures. 

2. Background color may vary slightly with ambient temperature; this phenomenon is reversible. 

3. Ta<=40°C: 85%RH MAX Ta>=40°C: Absolute humidity must not exceed the equivalent of 85% RH at 40°C. 

Copyright © Bridgetek Pte Ltd 

8 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **5.2 Electrical Specifications** 

## **5.2.1 Electrical Characteristics** 

Condition: VSS=0V, Ta=25°C 

|**Item**|**Item**|**Symbol**|**Min.**|**Typ.**|**Max.**|**Unit**|**Note**|
|---|---|---|---|---|---|---|---|
|Power Supply||VDD|2.3|2.5|2.7|V||
|||VDD_CTP|2.8|3.3|3.47|V||
|||AVDD|8.0|8.2|8.4|V||
|||VCOM|2.7|3.0|3.3|V|Note 1|
|||VGH|21.7|22.0|22.3|V||
|||VGL|-7.3|-7.0|-6.7|V||
|Input<br>Voltage|‘H’|VIH|0.8*VDD|-|3.6|V||
||‘L’|VIL|0|-|0.2*VDD|V||



**Table 7 - Electrical Characteristics** 

**Note:** 

1. The typical VCOM value is provided for reference only. The actual VCOM must be optimized for each individual LCM. A variable resistor is required to perform this adjustment. 

**Figure 1 - VCOM reference circuit** 

## **5.2.2 Current Consumption** 

|**Item**|**Symbol**|**Values**|**Values**|**Values**|**Unit**|**Remark**|
|---|---|---|---|---|---|---|
|||**Min.**|**Typ. **|**Max.**|||
|Current for Driver|IGH|300|705|1000|uA|VGH= 22V|
||IGL|300|705|1000|uA|VGL= -7V|
||IVDD|50|95|120|mA|VDD= 2.5V|
||IAVDD|8|45|70|mA|AVDD=8.2V|



**Table 8 - Current Consumption** 

Copyright © Bridgetek Pte Ltd 

9 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **5.2.3 LED Backlight Specification** 

Condition: VSS=0V, Ta=25°C 

|**Item**|**Symbol**|**Min.**|**Typ. **|**Max.**|**Unit**|**Note**|
|---|---|---|---|---|---|---|
|SupplyVoltage|Vf|16.2|18.0|19.8|V||
|SupplyCurrent|If|-|360|-|mA||
|Uniformity|∆ Bp|75|80|-|%||
|Life Time|time|20K|-|-|hours|Note 1|



**Table 9 - LED Backlight Specification** 

## **Note:** 

1. Brightness decreases to 50% of its initial value at an ambient temperature of Ta = 25°C. 

## **5.2.4 AC Electrical Characteristics** 

|**Item**|**Symbol**|**Values**|**Values**|**Values**|**Unit**|**Note**|
|---|---|---|---|---|---|---|
|||**Min.**|**Typ. **|**Max.**|||
|LVDS Differential Input<br>High Threshold Voltage|RxVTH|-|-|100|mV|RxVCM=1.2V|
|LVDS Differential Input Low<br>Threshold Voltage|LVDS Differential Input Low<br>RxVTL|-100|-|-|mV||
|LVDS Differential Input<br>Common Mode Voltage|RxVCM|0.7|-|1.6|V||
|LVDS Differential Voltage||VID||200|-|600|mV||



**Table 10 - AC Electrical Characteristics** 

**==> picture [198 x 10] intentionally omitted <==**

**----- Start of picture text -----**<br>
Figure 2 - AC Electrical Characteristics<br>**----- End of picture text -----**<br>


Copyright © Bridgetek Pte Ltd 

10 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## Ry«on BridgetekBRIDGING. TECHNOLOGY 

## **5.3 Timing** 

## **5.3.1 Input Timing Characteristics** 

|~~ee~~||~~ee~~|~~ee~~|~~ee~~||~~ee~~|
|---|---|---|---|---|---|---|
|**Item**<br>~~ee~~<br>~~a~~|**Symbol**<br>~~ee~~|**Values**<br>~~ee~~|||**Unit**|**Note**<br>~~ee~~|
|||**Min.**<br>~~ee~~<br>~~ee~~|**Typ. **<br>~~ee~~<br>~~ee~~|**Max.**<br>~~ee~~|||
|Clock Frequency<br>~~ee~~<br>~~a~~|1/TC<br>~~ee~~|68.9<br>~~ee~~<br>~~ee~~|71.1<br>~~ee~~<br>~~ee~~|73.4<br>~~ee~~|MHz|Frame rate =<br>60Hz<br>~~ee~~|
|Horizontal Display Area<br>~~a~~|tHD<br>~~ee~~|1280<br>~~ee ee~~|||TC||
|HS Period Time|tH|1410|1440|1470|TC||
|HS Width + Back Porch +<br>Front Porch|tHW+ tHBP+ tHFP|60|160|190|TC||
|Vertical Display Area|tVD|800|||tH||
|VS Period Time|tV|815|823|833|tH||
|VS Width + Back Porch +<br>FrontPorch|tVW+ tVBP+ tVFP|15|23|33|tH||



**Figure 3 - Input Timing Characteristic** 

Copyright © Bridgetek Pte Ltd 

11 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## «on BridgetekBRIDGING TECHNOLOGY 

## **5.3.2 LVDS Data Input Format** 

**Figure 4 - LVDS Data Input Format** 

## **5.4 Power Sequence** 

## **5.4.1 Power ON Sequence** 

**Figure 5 - Power ON Sequence** 

|**Symbol**|**Values**|**Values**|**Values**|**Unit**|
|---|---|---|---|---|
||**Min.**|**Typ.**|**Max.**||
|T1|0.5|2|10|ms|
|T2|0|5|50|ms|
|T3|0|5|50|ms|
|T4|0|6|100|ms|
|T5|120|130|200|ms|



**Table 12 - Power ON Sequence** 

Copyright © Bridgetek Pte Ltd 

12 

« Bridgetek 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **5.4.2 Power OFF Sequence** 

**Figure 6 - Power OFF Sequence** 

|**Symbol**|**Values**|**Values**|**Values**|**Unit**|
|---|---|---|---|---|
||**Min.**|**Typ.**|**Max.**||
|T6|0.5|2|10|ms|
|T7|0|7|50|ms|
|T8|0|5|10|ms|
|T9|0|1|10|ms|
|T10|0|2|100|ms|



**Table 13 - Power OFF Sequence** 

Copyright © Bridgetek Pte Ltd 

13 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## «RYoy BridgetekBRIDGING= TECHNOLOGY 

## **5.5 Optical Specifications** 

**==> picture [451 x 276] intentionally omitted <==**

**----- Start of picture text -----**<br>
Poi Item  Symbol Condition  Min.  Typ.  Max.  Unit  Note<br>Brightness  Bp -  700  -  Cd/m [2 ] Note 1<br>θ =0°<br>Note 1<br>Uniformity  ⊿ Bp  Ф=0°  70  80  -  %<br>SO Note 2<br>3:00  -  80  -<br>| ee<br>6:00  -  80  -<br>Viewing Angle  | Cr≥10  ee e ee Deg  Note 3<br>9:00  -  80  -<br>| ee e ee<br>12:00  -  80  -<br>| e ee ee eeeee<br>Contrast Ratio  Cr  θ =0°  600  800  -  -  Note 4<br>e Response Time  e eee Tr + Tf  Ф=0°  ao -  25  ee ee 50  ms  ee Note 5  ee<br>x  0.290  -<br>W<br>y  0.358  -<br>i| | || || |<br>R  x  0.589  -<br>Color of CIE Coordinate oi| y  | θ =0°  Typ  || 0.323  Typ  || -  | Note 1<br>G  x  -0.05  0.330  +0.05  -<br>Ф=0°  Note 6<br>y  0.578  -<br>=|| | || |<br>B  x  0.146  -<br>y  0.140  -<br>oi | | |<br>NTSC Ratio  S  40  50  -  %<br>ee ee|| ee| ee ee | ee|<br>Table 14 - Optical Specifications<br>**----- End of picture text -----**<br>


## **Remark:** _**Parameters may vary slightly depending on temperature, driving voltage, and material.**_ 

## **Note :** 

1. Data was measured after the LEDs were turned on for 5 minutes with the LCM displaying full white. Brightness is the average value of 9 measured points. Measurement equipment: PR-705 (Ф8mm) Measuring Conditions: 

   - Environment: Dark room 

   - Temperature: Ta=25 **°** C 

   - Operating voltage adjusted for optimum contrast at the center of the display 

   - Values measured at the center point of the LCD panel after more than 5 minutes of backlight operation 

**Figure 7 - Measurement Setup** 

2. The luminance uniformity is calculated using the following formula: 

𝐁𝐩 (𝐌𝐢𝐧.) ⊿ Bp = x 100% 𝐁𝐩 (𝐌𝐚𝐱.) 

Bp (Max.) = Maximum brightness in 9 measured spots Bp (Min.) = Minimum brightness in 9 measured spots 

Copyright © Bridgetek Pte Ltd 

14 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

**Figure 8 - Measurement Point** 

3. Definition of viewing angle: Refer to the figure below, indicated by θ and Ф. 

**Figure 9 - Viewing Angle** 

4. Contrast ratio is calculated using the following formula. (Test equipment: DMS501) 

**Figure 10 - Contrast Ratio** 

𝐁𝐫𝐢𝐠𝐡𝐭𝐧𝐞𝐬𝐬 𝐨𝐟 𝐬𝐞𝐥𝐞𝐜𝐭𝐞𝐝 𝐝𝐨𝐭𝐬 Contrast ratio, Cr = 𝐁𝐫𝐢𝐠𝐡𝐭𝐧𝐞𝐬𝐬 𝐨𝐟 𝐧𝐨𝐧−𝐬𝐞𝐥𝐞𝐜𝐭𝐞𝐝 𝐝𝐨𝐭𝐬 

5. Definition of response time. (Test equipment: DMS501) 

   - The output signals of the photo detector are measured when the input signal changes from “black” to “white” (falling time) and from “white” to “black” (rising time). Response time is defined as the time interval between 10% and 90% of the signal amplitude. Refer to the figure below for illustration. 

Copyright © Bridgetek Pte Ltd 

15 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## 7YY . «*N BridgetekBRIDGING TECHNOLOGY 

**Figure 11 - Definition of Response Time** 

6. Definition of color in terms of CIE coordinates and NTSC ratio. Color gamut: 

**==> picture [143 x 20] intentionally omitted <==**

**----- Start of picture text -----**<br>
𝐀𝐫𝐞𝐚 𝐨𝐟 𝐑𝐆𝐁 𝐭𝐫𝐢𝐚𝐧𝐠𝐥𝐞<br>S = x 100%<br>𝐀𝐫𝐞𝐚 𝐨𝐟 𝐍𝐓𝐒𝐂 𝐭𝐫𝐢𝐚𝐧𝐠𝐥𝐞<br>**----- End of picture text -----**<br>


**Figure 12 - 1931 CIE Chromaticity Diagram** 

7. Definition of cross talk. 

|𝐏𝐚𝐭𝐭𝐞𝐫𝐧 𝐀 𝐁𝐫𝐢𝐠𝐡𝐭𝐧𝐞𝐬𝐬−𝐏𝐚𝐭𝐭𝐞𝐫𝐧 𝐁 𝐁𝐫𝐢𝐠𝐡𝐭𝐧𝐞𝐬𝐬| Cross talk ratio(%)= x 100% 𝐏𝐚𝐭𝐭𝐞𝐫𝐧 𝐀 𝐁𝐫𝐢𝐠𝐡𝐭𝐧𝐞𝐬𝐬 **Electric volume value=3F+/-3Hex** 

**Figure 13 - Definition of Cross talk** 

Copyright © Bridgetek Pte Ltd 

16 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **6 Reliability Test Items** 

|**Test Item**|**Test Conditions**|**Note**|
|---|---|---|
|High Temperature<br>Storage|Ta= +60°C<br>96hrs|Note 1, 3, 4|
|Low Temperature<br>Storage|Ta= -20°C<br>96hrs|Note 1, 3, 4|
|High Temperature<br>Operation|Ta= +50°C<br>96hrs|Note 2, 3, 4|
|Low Temperature<br>Operation|Ta= 0°C<br>96hrs|Note 1, 3, 4|
|High Temperature and<br>Humidity Storage|High Temperature and<br>Ta= +40°C, 90%RH<br>96hrs|Note 3, 4|
|Thermal Shock|0°C /30 min ~ +50°C /30 min for 100 cycles<br>Start with cold temperature<br>End with high temperature|Note 3, 4|
|Vibration Test|Frequency range: 10~55Hz<br>Stroke: 1.5mm<br>Sweep: 10Hz~55Hz~10Hz<br>2 hours for each direction of X, Y and Z (6 hours for<br>total)||
|Mechanical Shock|100G 6ms, ±X, ±Y and ±Z, 3 times for each direction||
|Package Vibration Test|Random vibration:<br>ISTA-3A 1Hz~200Hz, Grms=0.53<br>Half hours for direction of Z||
|Package Drop Test|Height: 60cm<br>1 corner, 3 edges, 6 surfaces||
|Electrostatic Discharge|± 2 kV, Human Body Mode,<br>100pF/1500Ω||



## **Table 15 - Reliability Test Items** 

## **Note :** 

1. Ta refers to the ambient temperature of the samples. 

2. Ts refers to the temperature of the panel’s surface. 

3. Under standard conditions, no practical issues are expected that would affect display function. After reliability testing, only operational functionality is guaranteed; cosmetic specifications are not guaranteed. 

4. Before performing cosmetic and functional tests, the product must be allowed sufficient recovery time, at least 2 hours at room temperature. 

Copyright © Bridgetek Pte Ltd 

17 

**DP-1011-01A Datasheet Version 1.0** 

**==> picture [121 x 26] intentionally omitted <==**

**----- Start of picture text -----**<br>
———<br>7 Dimension<br>**----- End of picture text -----**<br>


Document Reference No.: BRT_000477   Clearance No.: BRT#242 

**==> picture [140 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
Figure 14 - LCM Dimension<br>**----- End of picture text -----**<br>


Copyright © Bridgetek Pte Ltd 

18 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **8 Disclaimer Notice: Use of Third-Party Software or Websites** 

We may recommend use of software or web sites that are owned or operated by other companies. We offer or facilitate this recommendation by hyperlinks or other methods to aid your access to the third-party resource. While we endeavour to direct you to helpful, trustworthy resources, we cannot endorse, approve, or guarantee software, information, products, or services provided by or at a thirdparty resource or track changes in the resource. Thus, we are not responsible for the content or accuracy of any third-party resource or for any loss or damage of any sort resulting from the use of, or for any failure of, products or services provided at or from a third party resource. 

We recommend these resources on an “as is” basis. When you use a third party resource, you will be subject to its terms and licenses and no longer be protected by our privacy policy or security practices, which may differ from the third policy or practices or other terms. You should familiarize yourself with any license or use terms of, and the privacy policy and security practices of, the third party resource, which will govern your use of that resource. 

Copyright © Bridgetek Pte Ltd 

19 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **9 Warranty Statement** 

According to our after-sales policy, the warranty (if applicable) will be void under the following circumstances: 

- The device has been damaged due to human factors, such as dropping, impact, water exposure, or unauthorized disassembly/modification. 

- The device has malfunctioned due to improper use, mishandling, or usage beyond its intended design. 

- The device has been disassembled, repaired, or modified by unauthorized personnel. 

- Any other conditions that do not comply with our warranty policy. For details, please contact our sales team. 

Copyright © Bridgetek Pte Ltd 

20 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **10 Contact Information** 

Refer to https://brtchip.com/contact-us/ for contact information. 

## **Distributor and Sales Representatives** 

Please visit the Distribution Network – IC & Module (brtchip.com) page for the contact details of our distributor(s) and sales representative(s) in your country. 

System and equipment manufacturers and designers are responsible to ensure that their systems, and any Bridgetek Pte Ltd (BRTChip) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested Bridgetek devices and other materials) is provided for reference only. While Bridgetek has taken care to assure it is accurate, this information is subject to customer confirmation, and Bridgetek disclaims all liability for system designs and for any applications assistance provided by Bridgetek. Use of Bridgetek devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless Bridgetek from any and all damages, claims, suits, or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted, or reproduced in any material or electronic form without the prior written consent of the copyright holder. Bridgetek Pte Ltd, 1 Tai Seng Avenue, Tower A, #03-05, Singapore 536464. Singapore Registered Company Number: 201542387H. 

Copyright © Bridgetek Pte Ltd 

21 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **Appendix A – References** 

## **Document References** 

NA 

## **Acronyms and Abbreviations** 

|**Terms**|**Description**|
|---|---|
|CABC|Content Adaptive Backlight Control|
|CTP|Capacitive Touch Panel|
|DC|Direct Current|
|FPC|Flexible Printed Circuit|
|IC|Integrated Circuit|
|I2C|Inter-Integrated Circuit|
|LCD|Liquid Crystal Display|
|LCM|Liquid Crystal Module|
|LED|Light Emitting Diode|
|LEDA|Light Emitting Diode Anode|
|LEDK|Light Emitting Diode Cathode|
|LVDS|Low-Voltage Differential Signaling|
|TFT|Thin Film Transistor|



Copyright © Bridgetek Pte Ltd 

22 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **Appendix B – List of Tables & Figures** 

## **List of Tables** 

|Table 1 - Part Number/Ordering Information ..................................................................... 2|Table 1 - Part Number/Ordering Information ..................................................................... 2|
|---|---|
|Table 2 - General Specifications ...................................................................................... 5|Table 2 - General Specifications ...................................................................................... 5|
|Table 3 - TFT-LCD Interface Pin Definition ........................................................................ 7|Table 3 - TFT-LCD Interface Pin Definition ........................................................................ 7|
|Table 4 - CTP Interface Pin Definition ............................................................................... 7|Table 4 - CTP Interface Pin Definition ............................................................................... 7|
|Table 5 - Electrical Absolute Maximum Ratings .................................................................. 8|Table 5 - Electrical Absolute Maximum Ratings .................................................................. 8|
|Table 6 - Environmental Absolute Maximum Ratings .......................................................... 8|Table 6 - Environmental Absolute Maximum Ratings .......................................................... 8|
|Table 7 - Electrical Characteristics ................................................................................... 9|Table 7 - Electrical Characteristics ................................................................................... 9|
|Table 8 - Current Consumption ....................................................................................... 9|Table 8 - Current Consumption ....................................................................................... 9|
|Table 9 - LED Backlight Specification .............................................................................. 10|Table 9 - LED Backlight Specification .............................................................................. 10|
|Table 10 - AC Electrical Characteristics ............................................................................ 10|Table 10 - AC Electrical Characteristics ............................................................................ 10|
|Table 11 - Input Timing Characteristic ............................................................................ 11|Table 11 - Input Timing Characteristic ............................................................................ 11|
|Table 12 - Power ON Sequence ...................................................................................... 12|Table 12 - Power ON Sequence ...................................................................................... 12|
|Table 13 - Power OFF Sequence ..................................................................................... 13|Table 13 - Power OFF Sequence ..................................................................................... 13|
|Table 14 - Optical Specifications ..................................................................................... 14|Table 14 - Optical Specifications ..................................................................................... 14|
|Table 15 - Reliability Test Items ..................................................................................... 17|Table 15 - Reliability Test Items ..................................................................................... 17|



## **List of Figures** 

|Figure 1 - VCOM reference circuit .................................................................................... 9|Figure 1 - VCOM reference circuit .................................................................................... 9|
|---|---|
|Figure 2 - AC Electrical Characteristics ............................................................................ 10|Figure 2 - AC Electrical Characteristics ............................................................................ 10|
|Figure 3 - Input Timing Characteristic ............................................................................. 11|Figure 3 - Input Timing Characteristic ............................................................................. 11|
|Figure 4 - LVDS Data Input Format ................................................................................. 12|Figure 4 - LVDS Data Input Format ................................................................................. 12|
|Figure 5 - Power ON Sequence ....................................................................................... 12|Figure 5 - Power ON Sequence ....................................................................................... 12|
|Figure 6 - Power OFF Sequence ...................................................................................... 13|Figure 6 - Power OFF Sequence ...................................................................................... 13|
|Figure 7 - Measurement Setup ....................................................................................... 14|Figure 7 - Measurement Setup ....................................................................................... 14|
|Figure 8 - Measurement Point ........................................................................................ 15|Figure 8 - Measurement Point ........................................................................................ 15|
|Figure 9 - Viewing Angle ............................................................................................... 15|Figure 9 - Viewing Angle ............................................................................................... 15|
|Figure 10 - Contrast Ratio ............................................................................................. 15|Figure 10 - Contrast Ratio ............................................................................................. 15|
|Figure 11 - Definition of Response Time .......................................................................... 16|Figure 11 - Definition of Response Time .......................................................................... 16|
|Figure 12 - 1931 CIE Chromaticity Diagram ..................................................................... 16|Figure 12 - 1931 CIE Chromaticity Diagram ..................................................................... 16|
|Figure 13 - Definition of Cross talk ................................................................................. 16|Figure 13 - Definition of Cross talk ................................................................................. 16|
|Figure 14 - LCM Dimension ............................................................................................ 18|Figure 14 - LCM Dimension ............................................................................................ 18|



Copyright © Bridgetek Pte Ltd 

23 

**DP-1011-01A Datasheet Version 1.0** 

Document Reference No.: BRT_000477   Clearance No.: BRT#242 

## **Appendix C – Revision History** 

Document Title: 

DP-1011-01A Datasheet 

Document Reference No.: BRT_000477 Clearance No.: BRT#242 - Product Page: https://brtchip.com/product category/products/ Document Feedback: Send Feedback 

|**Revision**|**Changes**|**Date**|
|---|---|---|
|Version 1.0|Initial Release|01-09-2025|



Copyright © Bridgetek Pte Ltd 

24