DLP180-24/E

**DENSEI-LAMBDA** 

## **DLP180-24-1  SPECIFICATIONS** 

## **CA735-01-01B** 

## **This specifications sheet also apply to option model /E,/EJ** 

|**CA735-01-01B**<br>**This specifications sheet also apply to option model /E,/EJ**|**CA735-01-01B**<br>**This specifications sheet also apply to option model /E,/EJ**|**CA735-01-01B**<br>**This specifications sheet also apply to option model /E,/EJ**|**CA735-01-01B**<br>**This specifications sheet also apply to option model /E,/EJ**||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|**ITEMS**<br>**MODE**||||**DLP180-24-1**|||||||||
|1|Nominal Output Voltage||V|24|||||||||
|2|Maximum Output Current||A|7.5|||||||||
|3|Maximum Output Power||W|180|||||||||
|4|Efficiency (100/230VAC) (Typ)<br>(* 1)||%|84/87|||||||||
|5|Input Voltage Range<br>(* 2)|||85 ~ 265VAC(47-63Hz)or 120 ~ 370VDC|||||||||
|6|Input Current(100/230VAC) (Typ)<br>(* 1)||A|2.3/1.0|||||||||
|7|Inrush Current(100/230VAC) (Typ)<br>(* 3)|||20A at 100VAC,45A at 230VAC,Ta=25~~o~~C,Cold Start|||||||||
|8|PFHC|||Built to meet IEC61000-3-2|||||||||
|9|Power Factor(Typ)|(* 1)||0.99 / 0.95|||||||||
|10|Output Voltage Range||V|21.6~28|||||||||
|11|Maximum Ripple & Noise<br>(* 4)|0≤Ta≤60°C|mV|240|||||||||
|||-10≤Ta<0°C|mV|360|||||||||
|12|Maximum Line Regulation<br>(* 4,5)||mV|120|||||||||
|13|Maximum Load Regulation<br>(* 4,6)||mV|192|||||||||
|14|Temperature Coefficient|||Less than 0.05%/°C|||||||||
|15|Over Current Protection<br>(* 7)||A|7.9~|||||||||
|16|Over Voltage Protection<br>(* 8)||V|30.0~35.0|||||||||
|17|Hold-UpTime(100/230VAC)<br>(* 1)|||20ms /30ms|||||||||
|18|Leakage current<br>(* 9)|||Less than 0.75mA|||||||||
|19|Parallel Operation|||-|||||||||
|20|Series Operation|||Possible|||||||||
|21|( * 10 )<br>Operating Temperature|||- 10 ~ + 60 °C<br>Convection: -10 ~ +50°C(100%);60°C(60%)|||||||||
|22|OperatingHumidity|||30 ~ 90 %RH(No dewdrop)|||||||||
|23|Storage Temperature|||- 30 ~ +85°C|||||||||
|24|Storage Humidity|||10 ~ 95%RH(No dewdrop)|||||||||
|25|Cooling|||Convection cooling|||||||||
|26|Withstand Voltage|||Input - Output : 3.0kVAC, Input - FG : 2.0kVAC (20mA) for 1min<br>Output -  FG : 500VAC(100mA)for 1min.|||||||||
|27|Isolation Resistance|||More than 100MΩat Ta=25°C and 70%RH,Output - FG : 500VDC|||||||||
|28|Vibration|||At no operating and with DIN RAIL,<br>10~55Hz(Sweepfor 1min)9.8m/s2Constant,X,Y,Z each 1hour|||||||||
|29|Shock(Inpackage)|||Less than 196m/s2|||||||||
|30|Safety|||Approved by UL60950,CSA60950, EN60950, UL508,  CSA C22.2 No14,<br>EN60529 IP20,EN50178 CATEGORY III(Primary),Built to meet DENAN|||||||||
|31|EMI|||Built to meet VCCI-B,FCC-ClassB,EN55011/EN55022-B|||||||||
|32|Immunity|||Built to meet IEC61000-6-2(IEC61000-4-2,-3,-4,-5,-6,-8,-11)|||||||||
|33|Weight(Typ)||g|780|||||||||
|34|Size(W.H.D.)||mm|80x97x110(Refer to Outline Drawing)|||||||||
|* Read instruction manual carefully , before using the power supply unit<br>= NOTES=<br>* 1 : At 100/230VAC and maximum output power, Ta = 25°C.<br>* 2 : For cases where conformance to various safety specs ( UL, CSA, EN ) are required,  to be<br>100 - 240VAC, 50 / 60Hz on name plate.<br>* 3 : Not applicable for the in-rush current to Noise Filter for less than 0.2ms<br>* 4 : Please refer to Fig A for measurement of line & load regulation and output ripple voltage<br>(Measure with JEITA RC-9131 probe)<br>* 5 : 85 - 265VAC, constant load.<br>* 6 : No load - Full load(Maximum power), constant input voltage<br>* 7 : Constant current limit with automatic recovery<br>Avoid to operate at overload or dead short for more than 30seconds<br>* 8 : OVP circuit will shutdown output, manual reset. (Re power on)<br>* 9 : Measured by each measuring method of UL, CSA, EN and<br>DENAN (at 60Hz).<br>*10: At standard mounting method, Fig B.<br> <br>+<br>-<br>Output<br>terminal||||||||described as<br>L<br>V||Output ter||Rail<br>Fig. B<br>Input terminal<br>Fig. A<br> <br>L : 150mm<br>C1 : Elec. Cap   100uF<br> <br>A<br>C2<br>minal|
||||||||||||||
||||||||-|V||+|C1<br>||
||||||||||||||
||||||||||||||
|- Load(%) is percent of maximum output load ( Item2 and 3 ), do<br>not exceed derating in both Maximum Output Current and Power.<br>Measurement point for<br>Vo Line/Load Regulation.<br>Me<br>for||||||||||asurement point<br>Vripple<br>C2 : Film Cap   0.1uF<br>Bandwidth of scope : 100MHz|||



- Load(%) is percent of maximum output load ( Item2 and 3 ), do not exceed derating in both Maximum Output Current and Power. 

- -For standard mounting, refer to derating curve (CA735-01-02_) 

**DENSEI-LAMBDA** 

## **DLP180-24-1 OUTPUT DERATING** 

## **CA735-01-02** 

**(This specifications sheet  also apply to option model /E,/EJ)** 

## **DLP180-24-1** 

||***COOLING: CONVECTION COOLING**|
|---|---|
|**Ta(°C)**|**LOADING CONDITION(%)**|
||**Standard Mounting**|
|**-10~50**|**100**|
|**60**|**60**|



**==> picture [421 x 259] intentionally omitted <==**

**----- Start of picture text -----**<br>
OUTPUT DERATING CURVE<br>100<br>80<br>60<br>40<br>20<br>0<br>-10 0 10 20 30 40 50 60<br>Ta (°C)<br>LOAD (%)<br>**----- End of picture text -----**<br>


**==> picture [338 x 145] intentionally omitted <==**

**----- Start of picture text -----**<br>
Output connector<br>Rail<br>                  Input connector<br>                                                         STANDARD   MOUNTING<br>**----- End of picture text -----**<br>