CCB250PS15

> **200/250 Watts** ~~lg~~ xppower.com **CCB200/250 Series** 

- 200 & 250 W Convection Cooled 

- Very Low Heat Loss 

- +70 °C Full Power Operation (CCB200) 

- Very High Efficiency up to 95% 

- 5 V Standby, Inhibit & Power Fail Signals 

- IT & Medical (BF) Safety Approvals 

- 3 Year Warranty 

## ~~**Specification**~~ 

## **Input** 

- Input Voltage • See derating curve Input Frequency • 47-63 Hz Input Current • 1.8/2.4 A typical at 115 VAC, full load (CCB200/250) 0.9/1.2 A typical at 230 VAC, full load (CCB200/250) 

- Inrush Current • 30 A typical at 230VAC, cold start at 25 °C Power Factor • >0.9 Earth Leakage Current • 250 µA max at 264 VAC/60 Hz No Load Input Power • <0.5 W when inhibit used (CCB200) Patient Leakage Current • 100 µA max, 264 VAC 60 Hz Input Protection • Internal T5.0 A/250 V fuse in line and neutral 

## **Output** 

- Output Voltage • 12-48 VDC (see tables) Output Voltage Trim • ±3% CCB250, ±5% CCB200 (See Mechanical Details) 

- Initial Set Accuracy • ±0.5% V1, ±5% V2 Minimum Load • No minimum load required Start Up Delay • 1 s typical Start Up Rise Time • 0.5 s typical Hold Up Time • 16/20 ms min at 90 VAC (CCB250/200) Drift • ±0.2% after 20 min warm up Line Regulation • ±0.5% max Load Regulation • ±1% V1, ±5% V2 Over/Undershoot • 5% max Transient Response • 4% max. deviation, recovery to within 1% in 500 µs for a 50-75-50% load change 

- Ripple & Noise • 1% pk-pk, 20 MHz bandwidth Overvoltage Protection • 115-140% Vnom, recycle input to reset (V1 only) 

- Overload Protection • 125-165% Inom V1 (CCB250), 110 - 150% Inom V1 (CCB200) 

- Short Circuit Protection • Continuous trip and restart (hiccup mode) Temperature • 0.05%/°C Coefficient Remote On/Off • Uncommitted isolated optocoupler diode, (Inhibit/Enable) powered diode inhibits V1 

## **General** 

|**General**|||
|---|---|---|
|Efficiency|•|Up to 95%|
|Isolation|•|4000 VAC Input to Output 2 x MOPP,|
|||1500 VAC Input to Ground 1 x MOPP,<br>1500 VAC Output to Ground 1 x MOPP|
|Switching Frequency|•|See longform datasheet|
|Signals|•|Power Fail|
|||Inhibit, 5 V Standby|
|MTBF|•|369/230 kHrs to MIL-HDBK-217F at|
|||25 °C, GB (CCB250/200)|



## **Environmental** 

- Operating Temperature • See derating curve & longform datasheet Cooling • Convection cooled Operating Humidity • 95% RH, non-condensing Storage Temperature • -40 °C to +85 °C Operating Altitude • 3048 m for CCB250, 5000 m for CCB200 Shock • ±3 x 30g shocks in each plane, total 18 shocks. 30g = 11ms (±0.5 ms), half sine, conforms to EN60068-2-27 & EN60068-2-47 

- Vibration • Single axis 10 - 500 Hz at 2g sweep and endurance at resonance in all 3 planes. Conforms to EN60068-2-6 

## **EMC & Safety** 

|**EMC & Safetyy**||
|---|---|
|Low Voltage PSU EMC|• EN61204-3, high severity level|
|Emissions<br>Harmonic Currents|• EN55011/22 level B conducted<br>EN55011/22 level A radiated,<br>See longform datasheet for level A<br>• EN61000-3-2, class A, >140w class C|
|Voltage Flicker<br>Radiated Immunity|• EN61000-3-3<br>• EN61000-4-3, level 3 Perf Criteria A|
|EFT/Burst|• EN61000-4-4, level 3 Perf Criteria A|
|Surge|• EN61000-4-5, installation class 3<br>Perf Criteria A|
|Conducted Immunity|• EN61000-4-6, level 3 Perf Criteria A|
|Dips & Interruptions|• EN61000-4-11 , 30% 10 ms, 60% 100 ms,|
|Safety Approvals|100% 5000 ms, Perf Criteria A, B, B ,<br>EN60601-1-2, 30% 500 ms, 60% 100 ms,<br>100% 10 ms, 100% 5000 ms, Perf Criteria<br>A, A, A, B - 230 VAC. Consult longform<br>datasheet for 115 V operation.<br>• IEC60950-1 CB report, UL60950-1, TUV|
||EN60950-1, IEC60601-1 CB report,|
||UL60601-1, TUV 60601-1,|
|Equipment Protection|• EN60601-1, ANSI/AAMI ES60601-1,|
|Class|CSA22.2 No.60601-1 per cUL BF Rated,|
||Including Risk Management, EN60950,|
||UL60950|



**CCB200** 

## ~~**Models and Ratings**~~ 

|Output Power|Output Voltage V1<br>Max Output Current V1|Max Output Current V1<br>5 V Standby (Optional)|Model Number|
|---|---|---|---|
|200 W|12.0 V<br>16.7 A|16.7 A<br>5 V/0.5 A|CCB200PS12|
|200 W|15.0 V<br>13.3 A|13.3 A<br>5 V/0.5 A|CCB200PS15|
|200 W|24.0 V|8.3 A<br>5 V/0.5 A|CCB200PS24|
|200 W|28.0 V|7.1 A<br>5 V/0.5 A|CCB200PS28|
|200 W|48.0 V|4.2 A<br>5 V/0.5 A|CCB200PS48|
|200 W|56.0 V|3.6 A<br>5 V/0.5 A|CCB200PS56|



## ~~**Notes**~~ 

_1. For covered version add suffix -C to model number e.g. CCB200PS12-C_ 

2. Add suffix -A for 5 V standby option, or -AC for standby and cover options combined. 

## ~~**Mechanical Details**~~ 

**==> picture [419 x 547] intentionally omitted <==**

**----- Start of picture text -----**<br>
5.00 ±0.02 (127.0 ±0.5) (0.307.50)<br>ø0.14 (3.5)<br>thru in 4 positions 7<br>Output<br>Voltage<br>L3 Control<br>A<br>C64<br>2.55 C53 -VE<br>(64.77) 0.92<br>(23.48) 1<br>2<br>1.49 +VE<br>io CP eee T1 | (37.91) Bee<br>Output Terminals<br>M4 Screws in<br>0.22 4.55 2 positions.<br>(5.71)0.22 (5.71) (115.57) (20.2)0.80 (90 cNm) max.Torque to 8lbs-in<br>Pin 2 Pin 1<br>1.43 ±0.04<br>(36.32 ±1.0) Pin 10 Pin 9<br>Mounting holes married with Detail A<br>must be connected to safety earth. . aa) | | fee ) Signals Connector CON4 ES<br>10 way JST B10B-PHDSS<br>0.13<br>(3.5)<br>ø0.14 (3.5)<br>thru in 4 positions 5.00 ±0.02 (127.0 ±0.51) 0.30 (7.5)<br>A<br>L3<br>A Output<br>C64 C53 under  Voltage<br>standby board Control<br>(64.7)2.55 B -VE<br>Standby<br>Board<br>T1 3.00 ±0.02(Option -A) 37.8)1.49 +VE<br>(76.2 ±0.51)<br>Output<br>Terminals<br>M4 Screws in<br>(5.71)0.22 (23.4)0.92 (5.71)0.22 4.55 (115.5) (20.2)0.80 Pin 4 2 positions.Torque to 8lbs-in<br>Pin 3 (90 cNm) max.<br>Pin 2<br>Pin 1<br>1.43 ±0.04<br>(36.32 ±1.0) Detail B<br>Standby Board O/P<br>Connector Cons<br>JST S48-PH-K-S<br>0.13<br>(3.5)<br>Mates with JST PHDR-4 housing<br>and JST SPH-002T-P0.5L crimp<br>terminals<br>In put Connector CON 1 Output Connector CON 3 Signals Connector CON 4 Standby Output<br>1 Line 1 +V1 1 Power Fail (Emitter) (Option -A)<br>2 Neutral 2 V1 RTN 2 Power Fail (Collector) 1 +5 V<br>Mates with Molex housing  3 Inhibit (Cathode) 2 +5 V<br>09-50-1031 and Molex series 4 Inhibit (Anode) 3 0 V<br>5 N/C 4 0 V<br>5194 crimp terminals.<br>6 N/C<br>7 - VE Sense<br>8 - VE Sense<br>9 +VE Sense<br>10 +VE Sense<br>Mates with JST PHDR-10VS<br>housing and JST SPHD-001T-<br>P0.5 crimp terminals<br>3.00 ±0.02 (76.2 ±0.5)<br>**----- End of picture text -----**<br>


## **CCB200PSxx Models** 

## **CCB200PSxx-A Models** 

~~**Notes**~~ 1. All dimensions in inches (mm). 2. Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25) 

3. Weight: 0.88 lb (400 g) approx 

**CCB200** 

## ~~**Mechanical Details**~~ 

## **CCB200PSxx-C Models** 

**==> picture [488 x 621] intentionally omitted <==**

**----- Start of picture text -----**<br>
M3 Mounting Holes<br>in 2 positions<br>0.39 4.72 (120.0)<br>(9.85) Pin 2 Pin 1<br>é<br>Pin 10 cH Pin 9<br>0.93<br>(23.7) : Signals Connector CON4Detail A<br>10 way JST B10B-PHDSS<br>1.75 (44.4) 5.50 ±0.02 (139.7 ±0.5) 0.59 (15.0)<br>Con 4<br>P=| A Output Voltage Control<br>| EERaces (z)@ Con 3<br>ia | 3.48 ±0.02<br>1 poe (88.5 ±0.5) ia r -VE Output Terminals<br>Con 1 2 oeaeeee Bha)Id (43.9)1.731.03 [feeSte +VE > (90 cNm) max.torque to 8 lbs 2 positionsM4 Screws in<br>c (26.1)<br>=7 !| Bessuseoor e beearntedco Hid a =il | Con 2<br>0.39 4.72 (120.0)<br>(9.85)<br>—<br>M3 mounting holes in 4 positions<br>| J} | 3.0 mm from bottom face of covermaximum penetration by screw to be 1In put Connector CON 1LineIn put Connector CON 1LineLine<br>2 Neutral<br>1.97<br>(50.0) Mates with Molex housing<br>09-50-1031 and Molex<br>series 5194 crimp terminals.<br>2<br>Output Connector CON 3put Connector CON 3ut Connector CON 3<br>1 +V1<br>0.7<br>(19.3) | 2 V1 RTN<br>Signals Connector CON 4gnals Connector CON 4nals Connector CON 4<br>M3 Mounting Holes 1 Power Fail (Emitter(EmitterEmitter)<br>0.39 4.72 (120.0) in 2 positions 2 Power Fail (Collector(CollectorCollector)<br>(9.85) Pin 2 Pin 1 3 Inhibit (Cathode)(Cathode)Cathode))<br>4 Inhibit (Anode)(Anode)Anode))<br>5 N/C<br>i Pin 10 Pin 9 6 N/C<br>(23.7)0.93 10 way JST B10B-PHDSSSignals Connector CON4Detail A 788 - VE Sense- VE Sense- VE Sense<br>9 +VE Sense<br>1.75 (44.4) 5.50 ±0.02 (139.7 ±0.5) 0.59 (15.0) 10 +VE Sense<br>KK<br>Con 4<br>Mates with JST PHDR-<br>P=|=— A Output Voltage Control 10VS housing and JST<br>| = @ Con 3 SPHD-001T-P0.5 crimp<br>1 ree 4 3.48 ±0.02 (88.5 ±0.5) ! Met B -VE Output Terminals  terminals<br>Con 1 = 2 ee 1.73 7s M4 Screws in<br>Doe im (43.9) [ize +VE > torque to 8 lbs 2 positions Standby Output<br>i Ie) (90 cNm) max. (Option -A)<br>= | aecc 2 (26.1)1.03 ie 1 +5 V<br>| Ni| |Bic | oo pe aont e oede Le=) | Con 2 2 +5 V<br>0.39 4.72 (120.0) 3 0 V<br>(9.85) 4 0 V<br>-;<br>M3 mounting holes in 4 positions<br>. 8) 3 : | 3.0 mm from bottom face of covermaximum penetration by screw to be housing and JST Mates with JST PHDR-4<br>SPH-002T-P0.5L crimp<br>1.97<br>(50.0) terminals<br>oe°<br>°<br>0.7<br>(19.3)<br>**----- End of picture text -----**<br>


**==> picture [87 x 55] intentionally omitted <==**

**----- Start of picture text -----**<br>
1In put Connector CON 1LineIn put Connector CON 1LineLine<br>2 Neutral<br>Mates with Molex housing<br>09-50-1031 and Molex<br>series 5194 crimp terminals.<br>**----- End of picture text -----**<br>


**==> picture [88 x 138] intentionally omitted <==**

**----- Start of picture text -----**<br>
Output Connector CON 3put Connector CON 3ut Connector CON 3<br>1 +V1<br>2 V1 RTN<br>|<br>Signals Connector CON 4gnals Connector CON 4nals Connector CON 4<br>1 Power Fail (Emitter(EmitterEmitter)<br>2 Power Fail (Collector(CollectorCollector)<br>3 Inhibit (Cathode)(Cathode)Cathode))<br>4 Inhibit (Anode)(Anode)Anode))<br>5 N/C<br>6 N/C<br>788 - VE Sense- VE Sense- VE Sense<br>9 +VE Sense<br>10 +VE Sense<br>**----- End of picture text -----**<br>


## **CCB200PSxx-AC Models** 

## ~~**Notes**~~ 

1. All dimensions in inches (mm). 2. Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25) 

**==> picture [103 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
3. Weight: 1.36 lb (618 g) approx<br>**----- End of picture text -----**<br>


**CCB250** 

## ~~**Models and Ratings**~~ 

|Output Power|Output Power|Output Voltage V1<br>Nominal|Output Current V1|Standby Supply V2|Model Number|
|---|---|---|---|---|---|
|Nominal|Nominal<br>Peak(1)||Nominal<br>Peak(1)|||
|250 W|250 W<br>300 W|12.0 V<br>20.8 A|20.8 A<br>25.00 A|5.0 V/0.5 A|CCB250PS12|
|250 W|250 W<br>300 W|15.0 V<br>16.7 A|16.7 A<br>20.00 A|5.0 V/0.5 A|CCB250PS15|
|250 W|250 W<br>300 W|24.0 V<br>10.4 A|10.4 A<br>12.50 A|5.0 V/0.5 A|CCB250PS24|
|250 W|250 W<br>300 W|28.0 V<br>8.9 A|8.9 A<br>10.70 A|5.0 V/0.5 A|CCB250PS28|
|250 W|250 W<br>300 W|36.0 V<br>6.9 A|6.9 A<br>8.30 A|5.0 V/0.5 A|CCB250PS36|
|250 W|250 W<br>300 W|48.0 V<br>5.2 A|5.2 A<br>6.25 A|5.0 V/0.5 A|CCB250PS48|



## ~~**Notes**~~ 

_1. Peak duration is 500ms max, average power must not exceed 250 W._ 

## ~~**Mechanical Details**~~ 

**==> picture [515 x 233] intentionally omitted <==**

**----- Start of picture text -----**<br>
6.00 (152.4)<br>0.24<br>(6.1)<br>Output<br>Signal Connector* Voltage<br>i @i nus! al Ls | =a Adjustment<br>ø 3.5 i)  cil L2 p Tae) a eT r e eet)<br>through<br>4 places -VE<br>= | Seva ame afc Ler<br>CON 3<br>(94.6)3.73 C12 101.6(4.0) 2.60 +VE<br>Output  (66.3)<br>connectors<br>CON 4 NL th= [lS oi connectionsfrom either allow  (50.4)1.98 vane 2 positionsM4 Screws in Output Terminals<br>0.74 E top or side torque to 8 lbs-in<br>(19.0) (90 cNm) max<br>©<br>0.14  C21<br>(3.5) 0.14  5.73 (145.42)<br>(3.5) *Signal Connector<br>Pin 2 a a ll Pin 1 CON 1 10-way<br>JST-BI0B-PHDSS<br>Mating Half - p/n<br>38.1 JST PHDR-10VS,<br>Mounting holes married with (1.5) Pin 10 Pin 9 Contact- 26-22 AWG<br>must be connected to safety earth. p/n JST SPHD-001T-P0.5<br>**----- End of picture text -----**<br>


**==> picture [299 x 110] intentionally omitted <==**

**----- Start of picture text -----**<br>
Signals Connector CON 1 Output Connector CON 3 In put Connector CON 4<br>1 5 V Standby Return 1 +V1 1 Line<br>2 V1 RTN 2 Neutral<br>2 5 V Standby<br>3 Earth<br>3 5 V Standby Return<br>4 5 V Standby Mates with Molex housing<br>5 5 V Standby Return 09-50-1051 and Molex series<br>6 5 V Standby 5194 crimp terminals.<br>7 Power Fail (Collector)<br>8 Power Fail (Emitter)<br>9 Remote On / Off (Cathode)<br>10 Remote On / Off (Anode)<br>**----- End of picture text -----**<br>


3. Weight 1.7 lb (780 g) approx 

2. Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25) 

~~**Notes**~~ 

1. All dimensions in inches (mm). 

**CCB** 

## ~~**Mechanical Details**~~ 

## ~~**Signals - CCB200**~~ 

**==> picture [500 x 133] intentionally omitted <==**

**----- Start of picture text -----**<br>
Power Fail Inhibit (High) Inhibit (Low)<br>5 V 5 V<br>POWER SUPPLY<br>POWER SUPPLY POWER SUPPLY<br>8V Max 3 mA Pin 2 CON 4Power Fail 5 mA    8 V Max 1K<br>Collector  Inhibit Hi  8 V Max<br>Pin 4 CON 4 Inhibit Hi<br>Transistor On: Input & Output Not OK Pin 4<br>Power Fail Transistor Off: Input & Output OK CON 4<br>Emitter<br>Pin 1 CON 4 Inhibit Lo Inhibit Lo<br>Pin 3 CON 4 5 mA Pin 3 CON 4<br>Signal Connector Pin 7 CON 4VI RTN Signal Connector Pin 7 CON 4VI RTN Signal Connector<br>**----- End of picture text -----**<br>


Signals Notes & Conditions Power Fail Uncomitted opto isolated transistor, normally off when AC is good (see fig.5) Provides 5 - 15ms warning of loss of output from AC failure Remote On/Off (Inhibit/Enable) Uncommited isolated optocoupler diode, powered diode inhibits the supply (see fig.6 & 7) 5 V Standby (Optional -A) 5 V/0.5 A Supply, always present when AC applied 

## ~~**Input Voltage & Temperature Derating - CCB200**~~ 

**==> picture [456 x 104] intentionally omitted <==**

**----- Start of picture text -----**<br>
220 200<br>182 Open Frame Convection<br>200<br>160 Standby Covered<br>180 150 [mona] Convection (-AC) [L]<br>160 Covered Convection (-C)<br>140 100<br>120<br>0<br>-20 -10 0 +50 +70 +85<br>80 85 90 264 300<br>Input Voltage (VAC) Ambient Temperature (ºC)<br>Output Power (W)<br>Output Power (Watts)<br>5 Seconds Maximum<br>**----- End of picture text -----**<br>


## ~~**Signals - CCB250**~~ 

**==> picture [493 x 179] intentionally omitted <==**

**----- Start of picture text -----**<br>
Power Fail Inhibit (High) Inhibit (Low)<br>POWER SUPPLY POWER SUPPLY<br>Pin 2, 4 & 6 5 V Standby  POWER SUPPLY<br>CON 15 V Standby   2K2 2, 4 & 6 CON 1 5 V Standby Pin 2, 4 & 6<br>5 mA    8 V Max CON 1<br>8V Max 3 mA Pin 7 CON 1<br>Power FailCollector  Pin 10 CON 1Inhibit Hi  Inhibit Hi 8 V Max<br>Pin 10<br>CON 1<br>EmitterPower Fail Transistor On (<0.8 V): Input & Output Not OKTransistor Off (>4.5 V): Input & Output OK Inhibit Lo Inhibit Lo<br>Pin 8 CON 1 Pin 9 CON 1 1K 5 mA Pin 9 CH 1 1K<br>5 V Standby RtnPin 1, 3 & 5CON 1 Logic GND Pin1, 3 & 5 CON 1 Logic GND Pin 1, 3 & 5 CON 1<br>Signal Connector Signal Connector Signal Connector<br>Signals Notes & Conditions<br>Power Fail Uncommitted opto isolated transistor, normally off when AC is good<br>Provides ≥ 5 ms (typically 20-30 ms) warning of loss of output from AC failure<br>Remote On/Off (Inhibit/Enable) Uncommitted isolated optocoupler diode, powered diode inhibits the supply<br>Standby Supply V2 Isolated 5 V/0.5 A supply, always present when AC supplied.<br>**----- End of picture text -----**<br>


## ~~**Input Voltage & Temperature Derating - CCB250**~~ 

**==> picture [422 x 83] intentionally omitted <==**

**----- Start of picture text -----**<br>
300 300<br>Peak Power Availability Peak Power Availability<br>250 250<br>200 200<br>150 150<br>100 e ee ee 100 eeoS<br>50 50<br>80 -—}-—} 85 90 +} 264 275 0-20 SFT -10 0 10 SE E  TE 40 50 60 4] 70<br>Input Voltage (VAC) Ambient Temperature (°C)<br>Output Power (W)<br>Output Power (W)<br>**----- End of picture text -----**<br>


10 Dec 15