BD9555FVM-CGTR

Datasheet OF 

## **CR Timer IC** 

## **50V 1ch Timer IC for Automotive BD9555FVM-C** 

## **General Description** 

ROHM’s BD9555FVM-C is 50V-withstanding 1ch CR timer IC. Cycle and duty width can be set through external resistance and capacity. It is most suitable as timer and OSC for Automotive, so input voltage range and operating temperature range are wide. 

## **Features** 

AEC-Q100 Qualified[(Note1)] Frequency and Duty Width Setting Through External Resistance and Capacity Wide Input Voltage Range Wide Operating Temperature Range Very Small MSOP8 Package 3 

Very Small MSOP8 Package (Note1:Grade1) 

## **Key Specifications** 

Input Voltage Range:               4.5V to 42V Operating Temperature Range:   -40°C to +125°C 

## **Special Characteristics** 

PWM Frequency Range:       1Hz to 10000Hz Duty Range:                       1% to 99% 

**Package W(Typ) x D(Typ) x H(Max)** MSOP8:               2.90mm x 4.00mm x 0.90mm = **Applications** All set for Automotive using timer or OSC such as Automotive LED module, etc. 

## **Typical Application Circuit** 

**==> picture [245 x 110] intentionally omitted <==**

**----- Start of picture text -----**<br>
VIN<br>CVIN<br>VIN  REN<br>CRT  DCENB<br>RCRT BD9555FVM-C  DCIN<br>DISC  OUT  OUT Q1<br>GND<br>CCRT<br>GND<br>**----- End of picture text -----**<br>


## **Pin Configurations, Descriptions and Marking Diagram** 

**==> picture [201 x 156] intentionally omitted <==**

**----- Start of picture text -----**<br>
DISC CRT GND N.C.<br>8 7 6 5<br>Part Number Marking<br>D 9 5<br>LOT Number<br>5  5<br>1PIN MARK<br>1 2 3 4<br>VIN DCENB N.C. OUT<br>MSOP8 (TOP VIEW)<br>**----- End of picture text -----**<br>


|Pin<br>No.|Symbol|Function|
|---|---|---|
|1|VIN|Power supply|
|2|DCENB|“L”:Output fixed “H” / “H”:PWM output|
|3|N.C.|N.C.|
|4|OUT|Output|
|5|N.C.|N.C.|
|6|GND|GND|
|7|CRT|CR connection|
|8|DISC|Discharge setting|



8 DISC Discharge setting 

**Ordering Information** 

- B D 9 5 5 5 F V M C T R Part Timer IC Package Product Rank Packaging and forming specification Number FVM : MSOP8 C : for Automotive Embossed tape and reel ~~SS~~ TR :  The pin number 1 is the upper right 

○Product structure：Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays 

. www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 14 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

1/12 

Datasheet 

**BD9555FVM-C** 

## **Physical Dimension, Tape and Reel Information** 

## Package Name 

## MSOP8 

**==> picture [267 x 148] intentionally omitted <==**

**----- Start of picture text -----**<br>
<Tape and Reel information><br>Tape Embossed carrier tape<br>Quantity 3000pcs<br>TR<br>Direction<br>of feed The direction is the 1pin of product is at the upper right when you hold<br>( reel on the left hand and you pull out the tape on the right hand )<br>OO 1pin<br>O O O O Oo © O O O O<br>| | UUW_ | _<br>\ —————— Direction of feed ><br>Reel ∗ [ Order quantity needs to be multiple of the minimum quantity.]<br>**----- End of picture text -----**<br>


www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

2/12 

Datasheet 

**BD9555FVM-C** 

## **Absolute Maximum Ratings** 

|**Absolute Maximum Ratingsbsolute Maximum Ratings**||||
|---|---|---|---|
|Parameter|Symbol|Rating|Unit|
|Power SupplyVoltage|VIN|-0.3 to +50|V|
|CRT,DISC,DCENB,OUT Terminal Voltage|VCRT,VDISC,VDCENB,VOUT|GND-0.3 to VIN+0.3|V|
|Output Current|Io|70|mA|
|Power Dissipation|Pd|0.38(Note1)|W|
|OperatingTemperature Range|Topr|-40 to +125|°C|
|Storage Temperature Range|Tstg|-55 to +150|°C|
|Junction Temperature|Tjmax|150|°C|



(Note1) Pd deleted at 3.8mW/°C at temperatures above Ta=25°C. **Caution:** Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. 

**Recommended Operating Range** 

|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|**Recommended Operating Rangeperating Rangeerating Rangeg Range Rangegee**|
|---|---|---|---|---|---|---|
|Parameter<br>Symbol<br>Limit<br>Unit<br>Power SupplyVoltage<br>VIN<br>4.5 ~ 42<br>V<br>OperatingTemperature Range<br>Topr<br>-40 ~ +125<br>°C<br>CR Timer FrequencyRange<br>FPWM<br>1~10000<br>Hz<br>PWM Minimum Pulse Width<br>TMIN<br>1<br>µs<br>~~———=~~|||||||
|**ecommended Operating Conditions**|||||||
||||Limit||||
|Parameter|Symbol|Min|Typ<br>Max|Unit|Conditions||
|Input Capacitor|CIN|0.1|-<br>-|µF|Ceramic capacitor recommended||
|CRT Terminal Capacitor|CCRT|19p|-<br>18µ|F|Ceramic capacitor recommended||
|CRT Terminal Resistor|RCRT|500|-<br>5M|Ω|||



## **Recommended Operating Conditions** 

(Note2) The minimum value of capacitor must be met this specifications over full operating conditions. (ex. Temperature, DC bias, aging conditions) (Note3) Set CCRT, RCRT to become desired frequency and Duty width by using equations shown in P.8. 

**Electrical Characteristics (Unless Otherwise Specified Ta=-40 to +125°C, VIN =13.0V)** 

|Parameter|Symbol|Limit|Limit|Limit|Unit|Conditions|
|---|---|---|---|---|---|---|
|||Min|Typ|Max|||
|Circuit Current|IIN|-|1.00|3.00|mA||
|CRT Terminal<br>Charge Current|ICRT_SO|29.75|35.00|40.25|µA|VCRT=0.9V|
|CRT Terminal<br>Charge ON Voltage|VCRT_CHA|0.99|1.10|1.21|V||
|CRT Terminal<br>Discharge ON Voltage|VCRT_DIS|2.7|3.0|3.3|V||
|CRT Terminal<br>Charge Resistance|RCHA|51.6|54.3|57.0|kΩ|RCHA= (VCRT_DIS- VCRT_CHA) / ICRT_SO|
|DISC Terminal<br>Discharge Resistance|RD|-|50.0|100|Ω|VCRT=3.4V|
|DCENB Terminal<br>“H”Input Voltage|VIH_DCENB|4.4|-|VIN<br>+0.2|V||
|DCENB Terminal<br>“L”Input Voltage|VIL_DCENB|GND<br>-0.2|-|3.6|V||
|“H” Output Voltage|VOH|11.0|12.3|-|V|IOH=-10mA|
|“L” Output Voltage|VOL|-|1.28|3.8|V|IOL=50mA|



www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

3/12 

Datasheet 

**BD9555FVM-C** 

## **Typical Performance Curves** 

(Reference Data : Unless Otherwise Specified VIN=13.0V, RCRT =2.7kΩ, CCRT =0.033µF, <FPWM=500Hz, Duty=5% setting>) 

**==> picture [494 x 556] intentionally omitted <==**

**----- Start of picture text -----**<br>
3 40<br>2<br>Ta=125°C<br>Ta=25°C<br>35<br>1<br>Ta=-40°C<br>0 30 =<br>0 10 20 30 40 50 -50 -25 0 25 50 75 100 125 150<br>Input Voltage  VIN [V] Temperature  Ta [°C]<br>Figure 1. Circuit Current vs Input Voltage  Figure 2. CRT Charge Current vs Temperature<br>1.5 3.5<br>1.0 3.0<br>0.5 nee 2.5<br>-50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150<br>Temperature  Ta [°C] Temperature  Ta [°C]<br> [µA]<br> [mA]IN CRT_SO<br>Circuit Current  I CRT Charge Current  I<br> [V]<br> [V]<br>CRT_DIS<br>CRT_CHA<br>CRT Charge ON Voltage  V<br>CRT Discharge ON Voltage  V<br>**----- End of picture text -----**<br>


Figure 3. CRT Charge ON Voltage vs Temperature 

Figure 4. CRT Discharge ON Voltage vs Temperature 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

4/12 

Datasheet 

**BD9555FVM-C** 

## **Typical Performance Curves – continued** 

(Reference Data : Unless Otherwise Specified VIN=13.0V, RCRT =2.7kΩ, CCRT =0.033µF, <FPWM=500Hz, Duty=5% setting>) 

**==> picture [494 x 557] intentionally omitted <==**

**----- Start of picture text -----**<br>
70 80<br>70<br>60 60<br>50<br>50 40<br>30<br>40 Se 20 ee<br>-50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150<br>Temperature  Ta [°C] Temperature  Ta [°C]<br>Figure 5. CRT Charge Resistance vs Temperature Figure 6. DISC Discharge Resistance vs Temperature<br>5 5<br>4 4<br>3 3<br>2 pe 2 e<br>-50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150<br>Temperature  Ta [°C] Temperature  Ta [°C]<br>]<br>Ω ]<br>Ω<br> [k  [<br> CHA D<br>CRT Charge Resistance  R<br>DISC Discharge Resistance  R<br> [V]  [V]<br>IH_DCENB IL_DCENB<br>DCENB "H" Input Voltage  V DCENB "L" Input Voltage  V<br>**----- End of picture text -----**<br>


Figure 7. DCENB “H” Input Voltage vs Temperature 

Figure 8. DCENB “L” Input Voltage vs Temperatute 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

5/12 

Datasheet 

**BD9555FVM-C** 

## **Typical Performance Curves – continued** 

(Reference Data : Unless Otherwise Specified VIN=13.0V, RCRT =2.7kΩ, CCRT =0.033µF, <FPWM=500Hz, Duty=5% setting>) 

**==> picture [495 x 558] intentionally omitted <==**

**----- Start of picture text -----**<br>
13 4<br>Ta=-40°C<br>Ta=25°C<br>3<br>12<br>Ta=125°C  Ta=25°C<br>2<br>Ta=125°C<br>11<br>1<br>Ta=-40°C<br>0<br>10<br>0 10 20 30 40 50 60 70 80 90 100<br>0 10 20 30<br>"H" Output Current  IOH [mA] "L" Output Current  IOL [mA]<br>Figure 9. “H” Output Voltage vs “H” Output Current Figure 10. “L” Output Voltage vs “L” Output Current<br>600 6<br>500 5<br>400 i 4<br>-50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100<br>Temperature  Ta [°C] Temperature  Ta [°C]<br> [V]  [V]<br>OH OL<br>"H" Output Voltage  V "L" Output Voltage  V<br> [Hz]<br>PWM PWM ON Duty  [%]<br>PWM Frequency  F<br>**----- End of picture text -----**<br>


**==> picture [87 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
Temperature  Ta [°C]<br>**----- End of picture text -----**<br>


Figure 11. PWM Frequency vs Temperature 

Figure 12. PWM On Duty vs Temperature 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

6/12 

Datasheet 

**BD9555FVM-C** 

## **Block Diagram** 

**==> picture [230 x 151] intentionally omitted <==**

**----- Start of picture text -----**<br>
VIN<br>VREF<br>EN<br>CRT OSC OUT<br>DISC<br>GND DCENB<br>**----- End of picture text -----**<br>


Figure 13. BD9555FVM-C Block Diagram 

## **Functional Description** 

Timer operation ON switches to OFF depending on DCENB terminal voltage. 

When DCENB terminal voltage under VIL_DCENB(3.6V(Max)), timer operation turns to OFF and output is “H”. When DCENB terminal voltage over VIH_DCENB(4.4V(Min)), CR timer function in IC is activated and triangular waveform is generated at CRT terminal. 

Output is “L” while CRT voltage is ramping up, and output is “H” while CRT voltage is ramping down. Ramp up / down time of CRT voltage can be set by values of external components (CCRT, RCRT) 

**==> picture [310 x 345] intentionally omitted <==**

**----- Start of picture text -----**<br>
VIN<br>+B<br>VREF<br>ICRT=35uA EN<br>CRT (Typ) OUT<br>OSC<br>CCRT RCRT<br>RD=50Ω(Typ)<br>DISC<br>GND DCENB<br>CRT Voltage Ramp-up CRT Voltage Ramp-down<br>V CRT_DIS 3.0V<br>CRT Terminal<br>Waveform  ΔV CRT<br>V CRT_CHA<br>1.1V<br>T1 T2<br>(1) T1= ΔV CRT x C CRT (2) T2= -C CRT x (R CRT + R D) x ln( V CRT_CHA )<br>ICRT_SO V CRT_DIS<br>VOH<br>OUT Terminal<br>Waveform<br>n VOL n<br>**----- End of picture text -----**<br>


www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

7/12 

Datasheet 

**BD9555FVM-C** 

- (1)CRT Ramp up Time T1 

CRT ramp up time can be obtained from the following equations: 

ΔVCRT x CCRT T1 = [s] ICRT_SO 

where: 

ICRT_SO is the CRT Terminal Charge Current 35µA (Typ) 

## (2)CRT Ramp down Time T2 

CRT ramp down time is defined by discharge period due to external capacity CCRT and resistance (RCRT+RD). (CRT Terminal Charge Current is OFF at CRT ramp down.) 

Make sure that T2 is set at not smaller than Min. pulse width 1µs. 

VCRT_CHA T2 =-CCRT x (RCRT + RD) x ln( )  [s] VCRT_DIS 

where: 

RD is the CRT Terminal Discharge Resistance           50Ω(Typ) 

VCRT_CHA is the CRT Terminal Charge ON Voltage       1.1V(Typ) 

VCRT_DIS is the CRT Terminal Discharge ON Voltage      3.0V(Typ) 

## (3)Frequency FPWM 

PWM Frequency is defined by T1 and T2. 

1 FPWM = [Hz] T1 + T2 ) T2 DON = ~~———q«X~~~ T1 + T2 

## (4)ON Duty (DON) 

Like the above, PWM ON duty is defined by T1 and T2. 

- (Ex) In case of FPWM=500Hz and 6% Duty(Typ) 

From FPWM=500Hz; 

T1 + T2 = 1 / FPWM = 1 / 500Hz = 2000µs 

From ON Duty = 6%; CRT ramp up time T1 is 

T1 = (T1 + T2) x 0.94 = 1880µs 

External capacity CCRT is; 

**==> picture [188 x 191] intentionally omitted <==**

**----- Start of picture text -----**<br>
10000 SSeeeaee RRR Ci RemERI Seem eee TI eee [eee] OTIT eee eee Tt eee eee<br>CACTHHATAG RH EEF HT no ofHo fo EH<br>T NIT tH ienmntiti! CTT TTT 7 I<br>1000<br>TENE NS, eet a<br>100 TpsbieteNtt PE EPNHDTENT \ OEOP E ENGHTLEN© \ Moats,@ yy& Ns,ONY?Wag NRbitinceHE staptranba e et stper<br>SEER OTT NCL<br>Ser ERAT ROMA: CATAT| UE RAEATLT| MURA NERS GT EE ARATE EAT<br>10 araeadopptttoaosfostatCICERO He Nast eee HEN E NESNoe esseTH<br>eesas [ae] tT ECORIoeET OG EEEORCOEOE GT SeTET<br>1 a ee ee AN cae ett!<br>0.0001 0.001 0.01 0.1 1 10 100<br>CCRT - Capacitance ［uF]<br>Frequency ［Hz］<br>**----- End of picture text -----**<br>


CCRT = T1 x (ICRT_SO /ΔVCRT) = 1880µs x 35µA / 1.9V ≒ 0.035µF 

CRT ramp down time T2 is; 

T2 = (T1 + T2) x 0.06 = 120µs 

External resistance RCRT is; 

RCRT = -T2 / (CCRT x ln(VCRT_CHA / VCRT_DIS)) – RD 

= -120µs / (0.035µF x ln(1.1 / 3.0)) - 50Ω ≒ 3.4kΩ 

And the characteristics example of frequency and duty is shown by the right figure. 

This is the reference value of external components, please decide its value by the above equations. 

**==> picture [186 x 195] intentionally omitted <==**

**----- Start of picture text -----**<br>
100 RCRT=10MΩ<br>90 RCRT=1MΩ<br>80<br>70<br>RCRT=100kΩ<br>60<br>50<br>40<br>30<br>20 RCRT=10kΩ<br>10<br>RCRT=1kΩ<br>0 Co eeey<br>0.0001 0.001 0.01 0.1 1 10 100<br>CCRT - Capacitance ［uF]<br>Duty ［%］<br>**----- End of picture text -----**<br>


Figure 14. Frequency and Duty Characteristics Example 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

8/12 

Datasheet 

**BD9555FVM-C** 

## **Timing Chart** 

**==> picture [291 x 331] intentionally omitted <==**

**----- Start of picture text -----**<br>
VIN<br>VIN<br>VREF<br>ICRT=35uA EN<br>CRT (Typ) OUT<br>OSC<br>CCRT RCRT<br>RD=50Ω(Typ)<br>DISC<br>DRL/Po<br>=e)<br>Signal GND DCENB<br>ON<br>Vcc<br>EE OFF<br>H<br>DRL/Po<br>Signal L<br>ee<br>H<br>VDCENB<br>L<br>TF _<br>VCRT<br>OUT<br>aiff<br>① ② ③<br>Figure 15. Recommended Application Circuit and Timing Chart<br>**----- End of picture text -----**<br>


- ① If VIN is switched ON and DCENB voltage is ”H” (VDCENB≧4.4V), VCRT will start oscillation, and according to its waveform rectangular wave is output by OUT. 

- ② If DCENB voltage is ”L”(VDCENB≦3.6V), OUT will be fixed at ”H”(ON Duty=100%) 

- ③ And DCENB voltage is ”H”, oscillation will start again. 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

9/12 

Datasheet 

**BD9555FVM-C** 

## **Operational Notes** 

## **1. Reverse Connection of Power Supply** 

Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 

## **2. Power Supply Lines** 

Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 

**3. Ground Voltage** 

Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 

**4. Ground Wiring Pattern** 

When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 

## **5. Thermal Consideration** 

Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 

**6. Recommended Operating Conditions** 

These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 

**7. Inrush Current** 

When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 

**8. Operation Under Strong Electromagnetic Field** 

Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 

## **9. Testing on Application Boards** 

When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 

## **10. Inter-pin Short and Mounting Errors** 

Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. 

## **11. Unused Input Pins** 

Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

10/12 

Datasheet 

**BD9555FVM-C** 

## **Operational Notes – continued** 

## **12. Regarding the Input Pin of the IC** 

This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): 

When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. 

Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. 

Figure 16. Example of monolithic IC structure 

## **13. Ceramic Capacitor** 

- When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 

## **14. Area of Safe Operation (ASO)** 

Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe Operation (ASO). 

www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

11/12 

Datasheet 

**BD9555FVM-C** 

## **Revision History** 

|Date|Revision||Changes|
|---|---|---|---|
|27.Oct.2014|001|New Release||
|29.Mar.2016|002|Correctionoferroneous description||



www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. TSZ22111 ・ 15 ・ 001 

**TSZ02201-0R7R0GZ95550-1-2 29.Mar.2016 Rev.002** 

12/12 

## **Notice** 

## **Precaution on using ROHM Products** 

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment[(Note 1)] , aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. 

|(Note1) Medical Equipment Classification of the Specific Applications|(Note1) Medical Equipment Classification of the Specific Applications|(Note1) Medical Equipment Classification of the Specific Applications|(Note1) Medical Equipment Classification of the Specific Applications|
|---|---|---|---|
|JAPAN|USA|EU|CHINA|
|CLASS`Ⅲ`|CLASS`Ⅲ`|CLASS`Ⅱ`b|CLASS`Ⅲ`|
|CLASS`Ⅳ`||CLASS`Ⅲ`||



2.  ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: 

   - [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions.  If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: 

   - [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents 

   - [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust 

   - [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 

   - [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items 

   - [f] Sealing or coating our Products with resin or other coating materials 

   - [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering 

   - [h] Use of the Products in places subject to dew condensation 

4. The Products are not subject to radiation-proof design. 

5. Please verify and confirm characteristics of the final or mounted products in using the Products. 

6.  In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 

7.  De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 

8.  Confirm that operation temperature is within the specified range described in the product specification. 

9.  ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. 

## **Precaution for Mounting / Circuit board design** 

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 

2.  In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. 

For details, please refer to ROHM Mounting specification 

> **[Notice-PAA-E ]** © 2015 ROHM Co., Ltd. All rights reserved. 

**Rev.003** 

## **Precautions Regarding Application Examples and External Circuits** 

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 

2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use.  Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document.  ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. 

## **Precaution for Electrostatic** 

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). 

## **Precaution for Storage / Transportation** 

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 

   - [b] the temperature or humidity exceeds those recommended by ROHM 

   - [c] the Products are exposed to direct sunshine or condensation 

   - [d] the Products are exposed to high Electrostatic 

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 

3.  Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 

4.  Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. 

## **Precaution for Product Label** 

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. 

## **Precaution for Disposition** 

When disposing Products please dispose them properly using an authorized industry waste company. 

## **Precaution for Foreign Exchange and Foreign Trade act** 

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. 

## **Precaution Regarding Intellectual Property Rights** 

1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. 

## **Other Precaution** 

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 

4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. 

> **[Notice-PAA-E ]** © 2015 ROHM Co., Ltd. All rights reserved. 

**Rev.003** 

Datasheet 

## **General Precaution** 

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 

2. All information contained in this docume nt is current as  of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this  document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. 

> **[Notice – WE ]** © 2015 ROHM Co., Ltd. All rights reserved. 

**Rev.001** 

**Datasheet** 

## BD9555FVM-C - Web Page 

Buy Distribution Inventory 

|Part Number|BD9555FVM-C|
|---|---|
|Package|MSOP8|
|Package<br>Unit Quantity|3000|
|Unit Quantity<br>Minimum Package Quantity|3000|
|Minimum Package Quantity<br>Packing Type|Taping|
|Packing Type<br>Constitution Materials List|Taping<br>inquiry|
|RoHS|inquiry<br>Yes|