B32934A3684K189

**==> picture [156 x 48] intentionally omitted <==**

## **Film Capacitors** 

## EMI Suppression Capacitors (MKT) 

**Series/Type: B32932 ... B32936** Date: June 2020 

© TDK Electronics AG 2020. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics' prior express consent is prohibited. 

**EMI Suppression Capacitors (MKT)** 

**B32932 ... B32936** 

## **X2 heavy duty series / 305 V AC** 

## **Typical applications** 

## **Dimensional drawing** 

- For connection in series with the mains 

- For severe ambient conditions 

- Capacitive power supply applications Energy meters 

## **Climatic** 

- Max. operating temperature: 105 °C Climatic category (IEC 60068-1:2013): 40/105/56 

## **Features** 

- High stability of capacitance value X2 safety approval (up to 2.2 μF) RoHS-compatible 

- AEC-Q200D compliant 

## **Construction** 

Dielectric: metallized polyester 

- Internal series connection 

- Plastic case (UL 94 V-0) 

- Epoxy resin sealing, flame-retardant 

## **Terminals** 

Dimensions in mm 

|Lead<br>spacing<br>±0.4<br>[é ||Lead<br>diameter<br>d1±0.05|Type|
|---|---|---|
|15|0.8|B32932|
|22.5|0.8|B32933|
|27.5|0.8|B32934|
|37.5|1.0|B32936|



Parallel wire leads, lead-free tinned Standard lead lengths: 6 _ 1 mm 

- Special lead lengths available on request 

## **Marking** 

Manufacturer's logo, lot number, date code, rated capacitance (coded), capacitance tolerance (code letter), rated AC voltage (IEC), series number, sub-class (X2), dielectric code (MKT), climatic category 

## **Delivery mode** 

Bulk (untaped, lead length 6 - 1 mm) Taped (Ammo pack or reel) 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 2 of 19 

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

**==> picture [37 x 42] intentionally omitted <==**

## **Marking example** 

**==> picture [121 x 90] intentionally omitted <==**

## **Approvals** 

|**Approvals**|||
|---|---|---|
|Approval<br>mark|Standards|Certificate|
||EN 60384-14:2014/A1:2016<br>IEC 60384-14:2013/AMD1:2016|40028058|
||UL 60384-14:2014|E97863|
||CSA E60384-14:2013|E97863|



Note: X2 safety approval for C ≤2.2 μF 

## **Overview of available types** 

|ead spacing|15 mm|22.5 mm|27.5 mm|37.5 mm|
|---|---|---|---|---|
|ype|B32932|B32933|B32934|B32936|
|CR (μF)|||||
|.047|||||
|.068|||||
|.10|||||
|.15|||||
|.22|||||
|.33|||||
|.47|||||
|.56|||||
|.68|||||
|.82|||||
|.0|||||
|.5|||||
|.2|||||



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 3 of 19 

**B32932 ... B32936** 

**==> picture [36 x 42] intentionally omitted <==**

## **X2 heavy duty series / 305 V AC** 

## **Ordering codes and packing units** 

|Lead<br>spacing<br>mm|CR<br>μF|Max. dimensions<br>w×h×l<br>mm|Ordering code<br>(composition see<br>below)|Ammo<br>pack<br>pcs./MOQ|Reel<br>pcs./MOQ|Untaped<br>pcs./MOQ|X2<br>safety<br>appr.|
|---|---|---|---|---|---|---|---|
|15|0.047<br>0.068<br>0.10<br>0.15<br>0.22<br>0.33<br>0.47|5.0×10.5×18.0<br>5.0×10.5×18.0<br>6.0×11.0×18.0<br>7.0×12.5×18.0<br>8.5×14.5×18.0<br>9.0×17.5×18.0<br>11.0×18.5×18.0|B32932A3473+***<br>B32932A3683+***<br>B32932A3104+***<br>B32932A3154+***<br>B32932A3224+***<br>B32932A3334+***<br>B32932A3474M***|4680<br>4680<br>3840<br>3320<br>2720<br>2560<br>–|5200<br>5200<br>4400<br>3600<br>2800<br>2800<br>2200|4000<br>4000<br>4000<br>4000<br>2000<br>2000<br>1200|X<br>X<br>X<br>X<br>X<br>X<br>X|
|22.5|0.10<br>0.15<br>0.22<br>0.33<br>0.47<br>0.47<br>0.56<br>0.68<br>0.82<br>1.0<br>1.0<br>1.5|6.0×15.0×26.5<br>6.0×15.0×26.5<br>7.0×16.0×26.5<br>7.0×16.0×26.5<br>8.5×16.5×26.5<br>10.5×16.5×26.5<br>10.5×16.5×26.5<br>10.5×18.5×26.5<br>12.0×22.0×26.5<br>12.0×22.0×26.5<br>14.5×29.5×26.5<br>14.5×29.5×26.5|B32933A3104+***<br>B32933A3154+***<br>B32933A3224+***<br>B32933A3334+***<br>B32933A3474M***<br>B32933B3474+***<br>B32933A3564+***<br>B32933A3684+***<br>B32933A3824+***<br>B32933A3105M***<br>B32933B3105+***<br>B32933A3155+***|2720<br>2720<br>2320<br>2320<br>1920<br>1560<br>1560<br>1560<br>–<br>–<br>–<br>–|2800<br>2800<br>2400<br>2400<br>2000<br>1600<br>1600<br>1600<br>–<br>–<br>–<br>–|2880<br>2880<br>2520<br>2520<br>2040<br>2160<br>2160<br>2160<br>1800<br>1800<br>1040<br>1040|X<br>X<br>X<br>X<br>X<br>X<br>X<br>X<br>X<br>X<br>X<br>X|



X = approval granted 

MOQ = Minimum Order Quantity, consisting of 4 packing units. Further intermediate capacitance values on request. 

## **Composition of ordering code** 

- + = Capacitance tolerance code: 

   - M = ±20% 

   - K = ±10% 

- *** = Packaging code: 

   - 289 = Straight terminals, Ammo pack 

   - 189 = Straight terminals, Reel 

   - 000 = Straight terminals, Untaped (standard lead length 6 �1 mm) 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 4 of 19 

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

**==> picture [37 x 42] intentionally omitted <==**

## **Ordering codes and packing units** 

|Lead<br>spacing<br>mm|CR<br>μF|Max. dimensions<br>w×h×l<br>mm|Ordering code<br>(composition see<br>below)|Ammo<br>pack<br>pcs./MOQ|Reel<br>pcs./MOQ|Untaped<br>pcs./MOQ|X2<br>safety<br>appr.|
|---|---|---|---|---|---|---|---|
|27.5|0.47<br>0.56<br>0.68<br>0.82<br>1.0<br>1.0<br>1.5<br>1.5<br>2.2|11.0×19.0×31.5<br>11.0×19.0×31.5<br>11.0×19.0×31.5<br>11.0×19.0×31.5<br>11.0×19.0×31.5<br>11.0×21.0×31.5<br>13.5×23.0×31.5<br>14.0×24.5×31.5<br>18.0×27.5×31.5|B32934A3474+***<br>B32934A3564+***<br>B32934A3684+***<br>B32934A3824+***<br>B32934A3105M***<br>B32934B3105+***<br>B32934B3155M***<br>B32934D3155+***<br>B32934B3225+***|–<br>–<br>–<br>–<br>–<br>–<br>–<br>–<br>–|1400<br>1400<br>1400<br>1400<br>1400<br>1400<br>1200<br>–<br>–|1280<br>1280<br>1280<br>1280<br>1280<br>1280<br>1120<br>1040<br>800|X<br>X<br>X<br>X<br>X<br>X<br>X<br>X<br>X|
|37.5|1.0<br>1.5<br>2.2|12.0×22.0×41.5<br>12.0×22.0×41.5<br>14.0×25.0×41.5|B32936A3105+***<br>B32936A3155+***<br>B32936A3225+***|–<br>–<br>–|–<br>–<br>–|1620<br>1620<br>1380|X<br>X<br>X|



X = approval granted 

MOQ = Minimum Order Quantity, consisting of 4 packing units. Further intermediate capacitance values on request. 

## **Composition of ordering code** 

- + = Capacitance tolerance code: 

   - M = ±20% 

   - K = ±10% 

- *** = Packaging code: 

   - 289 = Straight terminals, Ammo pack 

   - 189 = Straight terminals, Reel 

   - 000 = Straight terminals, Untaped (standard lead length 6 �1 mm) 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 5 of 19 

**==> picture [36 x 42] intentionally omitted <==**

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

## **Technical data** 

Reference standard: IEC 60384-14:2013/AMD1:2016 and AEC-Q200D. 

|Max. operating temperature Top,max<br>(Top= TA+ self-heating)|+105°C|+105°C||
|---|---|---|---|
|Dissipation factor tanδ(in 10-3)<br>at 20°C (upper limit values)|at|C≤1 μF|C > 1 μF|
||1 kHz|8|8|
||10 kHz|15|�|
|Insulation resistance Rins<br>or time constantτ= CR�Rins<br>at 20°C, rel. humidity≤65%<br>(minimum as-delivered values)|CR≤0.33 μF||CR> 0.33 μF|
||30 000 MΩ||10 000 s|
|DC test voltage|1312 V DC, 2 s(4.3�VR accordingto IEC 60384-14)|||
|Passive flammability category to<br>IEC 40(CO)752|B|||
|Capacitance tolerances<br>(measured at 1 kHz)|±10% (K),±20% (M)|||
|Rated AC voltage ( IEC 60384-14 )<br>Maximum continuous DC voltage VDC|305 V (50/60 Hz)<br>500 V at Top≤85°C<br>1.5% /°C deratingwhen 85°C < Top ≤110°C|||
|Operating voltage Vopat high<br>temperature|Top≤105°C||Vop= 1.25�VAC(1000 h)|
|Damp heat test<br>Limit values after damp heat test|Test conditions:<br>1. Temperature:<br>Relative humidity (RH):<br>Test duration:<br>Voltage value:<br>+85°C±2°C<br>85%±2%<br>1000 hours<br>240 V AC, 50 Hz<br>2. Temperature:<br>Relative humidity (RH):<br>Test duration:<br>Voltage value:<br>+40°C±2°C<br>93%±2%<br>2000 hours<br>305 V AC, 50 Hz<br>Capacitance change (ΔC/C):<br>Dissipation factor change (Δtanδ):<br>Δtanδ/tanδ:<br>≤10%<br>≤5�10-3 (at 1 kHz)<br>≤100% (at 10 kHz)<br>Insulation resistance Rins<br>or time constantτ= CR�Rins:<br>> 10 MΩ|||



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 6 of 19 

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

**==> picture [37 x 42] intentionally omitted <==**

## **Pulse handling capability** 

"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/μs. 

"k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V[2] /μs. 

## _Note:_ 

_The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor._ 

## **dV/dt and k0 values** 

|**dV/dt and k0 values**|||||
|---|---|---|---|---|
|Lead spacing (mm)|15|22.5|27.5|37.5|
|dV/dt(V/μs)|90|50|35|25|
|k0 (V2/μs)|108000|60000|42000|30000|



## **Mounting guidelines** 

## **1 Soldering** 

## **1.1 Solderability of leads** 

The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. 

Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. 

|Solder bath temperature|235±5°C|
|---|---|
|Solderingtime|2.0±0.5 s|
|Immersion depth|2.0 +0/�0.5 mm from capacitor bodyor seating plane|
|Evaluation criteria:<br>Visual inspection|Wetting of wire surface by new solder≥90%,<br>free-flowingsolder|



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 7 of 19 

**==> picture [36 x 42] intentionally omitted <==**

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

**1.2 Resistance to soldering heat** Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1. Conditions: 

|Series|Series|Series|Series|Series|Series|Series|Series|Solder bath temperature|Solderingtime|
|---|---|---|---|---|---|---|---|---|---|
|MKT|boxed (except 2.5×6.5×7.2 mm)<br>coated<br>uncoated(lead spacing>10 mm)|||||||260±5°C|10±1 s|
|MFP<br>MKP|(lead spacing>7.5 mm)|||||||||
|MKT|boxed(case 2.5×6.5×7.2 mm)||||||||5±1 s|
|MKP<br>MKT|(lead spacing≤7.5 mm)<br>uncoated (lead spacing≤10 mm)<br>insulated (B32559)||||||||<4 s<br>recommended soldering<br>profile for MKT uncoated<br>(lead spacing≤10 mm) and<br>insulated(B32559)|
|||||||||||
|||||||||||
|||||||||||
|||||||||||
|||||||||||
|||||||||||
|||||||||||
|||||||||||
|||||||||||
|Immersion depth||||||||2.0 +0/�0.5 mm from capacitor bodyor seating plane||
|Shield||||||||Heat-absorbing board, (1.5±0.5) mm thick, between<br>capacitor bodyand liquid solder||
|Evaluation criteria:<br>Visual inspection<br>ΔC/C0<br>tanδ||||||||No visible damage<br>2% for MKT/MKP/MFP<br>5% for EMI suppression capacitors<br>As specified in sectional specification||



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 8 of 19 

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

## **1.3 General notes on soldering** 

Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics. For short exposures (as in practical soldering processes) the heat load (and thus the possible effects on a capacitor) will also depend on other factors like: 

- a Pre-heating temperature and time 

- a Forced cooling immediately after soldering 

- a Terminal characteristics: diameter, length, thermal resistance, special configurations (e.g. crimping) 

- a Height of capacitor above solder bath 

- a Shadowing by neighboring components 

- a Additional heating due to heat dissipation by neighboring components a Use of solder-resist coatings 

The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced cooling process may possibly have to be included. 

## **Recommendations** 

As a reference, the recommended wave soldering profile for our film capacitors is as follows: 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 9 of 19 

## **B32932 ... B32936** ~~rs~~ **X2 heavy duty series / 305 V AC** 

Body temperature should follow the description below: 

MKP capacitor 

During pre-heating: Tp ≤110 °C 

During soldering: Ts ≤120 °C, ts ≤45 s 

MKT capacitor 

During pre-heating: Tp ≤125 °C 

During soldering: Ts ≤160 °C, ts ≤45 s 

When SMD components are used together with leaded ones, the film capacitors should not pass into the SMD adhesive curing oven. The leaded components should be assembled after the SMD curing step. 

Leaded film capacitors are not suitable for reflow soldering. 

In order to ensure proper conditions for manual or selective soldering, the body temperature of the capacitor (Ts) must be ≤120 °C. 

One recommended condition for manual soldering is that the tip of the soldering iron should be <360 °C and the soldering contact time should be no longer than 3 seconds. 

For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following measures are recommended: 

pre-heating to not more than 110 °C in the preheater phase 

rapid cooling after soldering 

Please refer to our Film Capacitors Data Book in case more details are needed. 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 10 of 19 

## **B32932 ... B32936** ~~as~~ **X2 heavy duty series / 305 V AC** 

## **Application note for the different possible X1 / X2 positions** 

## **In series with the powerline (i.e. capacitive power supply)** 

Typical Applications: 

- Power meters 

- ECUs for white goods and household appliances 

## **In parallel with the powerline** 

Typical Applications: 

Standard X2 are used parallel over the mains for reducing electromagnetic interferences coming from the grid. For such purposes they must meet the applicable EMC directives and standards. 

- Different sensor applications 

- Severe ambient conditions 

## **Basic circuit** 

## **Basic circuit** 

## **Required features** 

## **Required features** 

   - Standard safety approvals (ENEC, UL, CSA, CQC) High pulse load capability Withstand surge voltages 

- High capacitance stability over the lifetime Narrow tolerances for a controlled current supply 

## **Recommended product series** 

## **Recommended product series** 

- || B3293* (305 V AC) heavy duty with B3292*C/D (305 V AC) EN approval for X2 (UL Q1/2010) standard series, approved as X2 

   - standard series, approved as X2 B3291* (330 V AC), approved as X1 B3291* (530 V AC), approved as X1 B3291* (550 V AC), approved as X1 

- | B3265* MKP series | standard MKP capacitor without safety rT] approvals | 

   - B3292*H/J (305 V AC), severe ambient condition, approved as X2 

- B3267*L MKP series 

- standard MKP capacitor without safety approvals 

- B3292*H/J (305 V AC), severe ambient condition, approved as X2 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 11 of 19 

**B32932 ... B32936** 

**==> picture [36 x 42] intentionally omitted <==**

## **X2 heavy duty series / 305 V AC** 

## **Cautions and warnings** 

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

**==> picture [7 x 7] intentionally omitted <==**

- Do not exceed the upper category temperature (UCT). Do not apply any mechanical stress to the capacitor terminals. Avoid any compressive, tensile or flexural stress. 

- Do not move the capacitor after it has been soldered to the PC board. Do not pick up the PC board by the soldered capacitor. 

- Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified lead spacing. 

- Do not exceed the specified time or temperature limits during soldering. 

- Avoid external energy inputs, such as fire or electricity. 

- Avoid overload of the capacitors. 

- Consult us if application is with severe temperature and humidity condition. 

- There are no serviceable or repairable parts inside the capacitor. Opening the capacitor or any attempts to open or repair the capacitor will void the warranty and liability of TDK Electronics. 

- Please note that the standards referred to in this publication may have been revised in the meantime. 

The table below summarizes the safety instructions that must always be observed. A detailed description can be found in the relevant sections of the chapters "General technical information" and "Mounting guidelines". 

|Topic|Safety information|Reference chapter<br>"General technical<br>information"|
|---|---|---|
|Storage<br>conditions|Make sure that capacitors are stored within the<br>specified range of time, temperature and humidity<br>conditions.|4.5<br>"Storage conditions"|
|Flammability|Avoid external energy, such as fire or electricity<br>(passive flammability), avoid overload of the capacitors<br>(active flammability) and consider the flammability of<br>materials.|5.3<br>"Flammability"|
|Resistance to<br>vibration|Do not exceed the tested ability to withstand vibration.<br>The capacitors are tested to IEC 60068-2-6:2007.<br>TDK Electronics offers film capacitors specially<br>designed for operation under more severe vibration<br>regimes such as those found in automotive<br>applications. Consult our catalog "Film Capacitors for<br>Automotive Electronics".|5.2<br>"Resistance to<br>vibration"|



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 12 of 19 

||**B32932 ... B32936**|
|---|---|
|**X2 heavy duty series / 305 V AC**|**X2 heavy duty series / 305 V AC**|



|Topic|Safety information|Reference chapter<br>"Mounting guidelines"|
|---|---|---|
|Soldering|Do not exceed the specified time or temperature limits<br>duringsoldering.|1 "Soldering"|
|Cleaning|Use onlysuitable solvents for cleaningcapacitors.|2 "Cleaning"|
|Embedding of<br>capacitors in<br>finished<br>assemblies|When embedding finished circuit assemblies in plastic<br>resins, chemical and thermal influences must be taken<br>into account.<br>Caution: Consult us first, if you also wish to embed<br>other uncoated component types!|3 "Embedding of<br>capacitors in finished<br>assemblies"|



## **Design of our capacitors** 

Our EMI capacitors use polypropylene (PP) film metalized with a thin layer of Zinc (Zn). The following key points have made this design suitable to IEC/UL testing, holding a minimum size. 

Overvoltage AC capability with very high temperature Endurance test of IEC 60384-14:2013 (4th edition) / UL 60384-14:2014 (2[nd] edition) must be performed at 1.25 × VR at maximum temperature, during 1000 hours, with a capacitance drift less than 10%. 

Higher breakdown voltage withstanding if compared to other film metallizations, like Aluminum. IEC 60384-14:2013 (4[th] edition) / UL 60384-14:2014 (2[nd] edition) establishes high voltage tests performed at 4.3 × VR 1 minute, impulse testing at 2500 V for C = 1 μF and active flammability tests. 

Damp heat steady state: 40 °C/ 93% RH / 56 days. (without voltage or current load) 

## **Effect of humidity on capacitance stability** 

Long contact of a film capacitor with humidity can produce irreversible effects. Direct contact with liquid water or excess exposure to high ambient humidity or dew will eventually remove the film metallization and thus destroy the capacitor. Plastic boxed capacitors must be properly tested in the final application at the worst expected conditions of temperature and humidity in order to check if any parameter drift may provoke a circuit malfunction. 

In case of penetration of humidity through the film, the layer of Zinc can be degraded, specially under AC operation (change of polarity), accelerated by the temperature, provoking an increment of the serial resistance of the electrode and eventually a reduction of the capacitance value. For DC operation, the parameter drift is much less. 

Plastic boxes and resins can not protect 100% against humidity. Metal enclosures, resin potting or coatings or similar measures by customers in their applications will offer additional protection against humidity penetration. 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 13 of 19 

**B32932 ... B32936** ~~ee~~ 

## **X2 heavy duty series / 305 V AC** 

## **Display of ordering codes for TDK Electronics products** 

The ordering code for one and the same product can be represented differently in data sheets, data books, other publications, on the company website, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. 

Detailed information can be found on the Internet under www.tdk-electronics.tdk.com/orderingcodes. 

Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 14 of 19 

## **B32932 ... B32936 X2 heavy duty series / 305 V AC** 

**==> picture [37 x 42] intentionally omitted <==**

## **Symbols and terms** 

|Symbol|English|German|
|---|---|---|
|α<br>αC<br>A<br>βC<br>C<br>CR<br>ΔC<br>ΔC/C<br>ΔC/CR<br>dt<br>Δt<br>ΔT<br>Δtanδ<br>ΔV<br>dV/dt<br>ΔV/Δt<br>E<br>ESL<br>ESR<br>f<br>f1<br>f2<br>fr<br>FD<br>FT<br>i<br>IC|Heat transfer coefficient<br>Temperature coefficient of capacitance<br>Capacitor surface area<br>Humidity coefficient of capacitance<br>Capacitance<br>Rated capacitance<br>Absolute capacitance change<br>Relative capacitance change (relative<br>deviation of actual value)<br>Capacitance tolerance (relative deviation<br>from rated capacitance)<br>Time differential<br>Time interval<br>Absolute temperature change<br>(self-heating)<br>Absolute change of dissipation factor<br>Absolute voltage change<br>Time differential of voltage function (rate<br>of voltage rise)<br>Voltage change per time interval<br>Activation energy for diffusion<br>Self-inductance<br>Equivalent series resistance<br>Frequency<br>Frequency limit for reducing permissible<br>AC voltage due to thermal limits<br>Frequency limit for reducing permissible<br>AC voltage due to current limit<br>Resonant frequency<br>Thermal acceleration factor for diffusion<br>Derating factor<br>Current (peak)<br>Category current (max. continuous<br>current)|Wärmeübergangszahl<br>Temperaturkoeffizient der Kapazität<br>Kondensatoroberfläche<br>Feuchtekoeffizient der Kapazität<br>Kapazität<br>Nennkapazität<br>Absolute Kapazitätsänderung<br>Relative Kapazitätsänderung (relative<br>Abweichung vom Ist-Wert)<br>Kapazitätstoleranz (relative Abweichung<br>vom Nennwert)<br>Differentielle Zeit<br>Zeitintervall<br>Absolute Temperaturänderung<br>(Selbsterwärmung)<br>Absolute Änderung des Verlustfaktors<br>Absolute Spannungsänderung<br>Differentielle Spannungsänderung<br>(Spannungsflankensteilheit)<br>Spannungsänderung pro Zeitintervall<br>Aktivierungsenergie zur Diffusion<br>Eigeninduktivität<br>Ersatz-Serienwiderstand<br>Frequenz<br>Grenzfrequenz für thermisch bedingte<br>Reduzierung der zulässigen<br>Wechselspannung<br>Grenzfrequenz für strombedingte<br>Reduzierung der zulässigen<br>Wechselspannung<br>Resonanzfrequenz<br>Therm. Beschleunigungsfaktor zur<br>Diffusion<br>Deratingfaktor<br>Stromspitze<br>Kategoriestrom (max. Dauerstrom)|



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 15 of 19 

**==> picture [36 x 42] intentionally omitted <==**

## **B32932 ... B32936 X2 heavy duty series / 305 V AC** 

|Symbol|English|German|
|---|---|---|
|IRMS<br>iz<br>k0<br>LS<br>λ<br>λ0<br>λtest<br>Pdiss<br>Pgen<br>Q<br>ρ<br>R<br>R<br>Ri<br>Rins<br>RP<br>RS<br>S<br>t<br>T<br>τ<br>tanδ<br>tanδD<br>tanδP<br>tanδS<br>TA<br>Tmax<br>Tmin<br>tOL<br>Top<br>TR<br>Tref<br>tSL|(Sinusoidal) alternating current,<br>root-mean-square value<br>Capacitance drift<br>Pulse characteristic<br>Series inductance<br>Failure rate<br>Constant failure rate during useful<br>service life<br>Failure rate, determined by tests<br>Dissipated power<br>Generated power<br>Heat energy<br>Density of water vapor in air<br>Universal molar constant for gases<br>Ohmic resistance of discharge circuit<br>Internal resistance<br>Insulation resistance<br>Parallel resistance<br>Series resistance<br>severity (humidity test)<br>Time<br>Temperature<br>Time constant<br>Dissipation factor<br>Dielectric component of dissipation<br>factor<br>Parallel component of dissipation factor<br>Series component of dissipation factor<br>Temperature of the air surrounding the<br>component<br>Upper category temperature<br>Lower category temperature<br>Operating life at operating temperature<br>and voltage<br>Operating temperature, TA+ΔT<br>Rated temperature<br>Reference temperature<br>Reference service life|(Sinusförmiger) Wechselstrom<br>Inkonstanz der Kapazität<br>Impulskennwert<br>Serieninduktivität<br>Ausfallrate<br>Konstante Ausfallrate in der<br>Nutzungsphase<br>Experimentell ermittelte Ausfallrate<br>Abgegebene Verlustleistung<br>Erzeugte Verlustleistung<br>Wärmeenergie<br>Dichte von Wasserdampf in Luft<br>Allg. Molarkonstante für Gas<br>Ohmscher Widerstand des<br>Entladekreises<br>Innenwiderstand<br>Isolationswiderstand<br>Parallelwiderstand<br>Serienwiderstand<br>Schärfegrad (Feuchtetest)<br>Zeit<br>Temperatur<br>Zeitkonstante<br>Verlustfaktor<br>Dielektrischer Anteil des Verlustfaktors<br>Parallelanteil des Verlfustfaktors<br>Serienanteil des Verlustfaktors<br>Temperatur der Luft, die das Bauteil<br>umgibt<br>Obere Kategorietemperatur<br>Untere Kategorietemperatur<br>Betriebszeit bei Betriebstemperatur und<br>-spannung<br>Beriebstemperatur, TA+ΔT<br>Nenntemperatur<br>Referenztemperatur<br>Referenz-Lebensdauer|



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 16 of 19 

**B32932 ... B32936 X2 heavy duty series / 305 V AC** 

**==> picture [37 x 42] intentionally omitted <==**

|Symbol|English|German|
|---|---|---|
|VAC<br>VC<br>VC,RMS<br>VCD<br>Vch<br>VDC<br>VFB<br>Vi<br>Vo<br>Vop<br>Vp<br>Vpp<br>VR<br>R<br>VRMS<br>VSC<br>Vsn<br>Z|AC voltage<br>Category voltage<br>Category AC voltage<br>Corona-discharge onset voltage<br>Charging voltage<br>DC voltage<br>Fly-back capacitor voltage<br>Input voltage<br>Output voltage<br>Operating voltage<br>Peak pulse voltage<br>Peak-to-peak voltage Impedance<br>Rated voltage<br>Amplitude of rated AC voltage<br>(Sinusoidal) alternating voltage,<br>root-mean-square value<br>S-correction voltage<br>Snubber capacitor voltage<br>Impedance<br>Lead spacing|Wechselspannung<br>Kategoriespannung<br>(Sinusförmige)<br>Kategorie-Wechselspannung<br>Teilentlade-Einsatzspannung<br>Ladespannung<br>Gleichspannung<br>Spannung (Flyback)<br>Eingangsspannung<br>Ausgangssspannung<br>Betriebsspannung<br>Impuls-Spitzenspannung<br>Spannungshub<br>Nennspannung<br>Amplitude der Nenn-Wechselspannung<br>(Sinusförmige) Wechselspannung<br>Spannung bei Anwendung "S-correction"<br>Spannung bei Anwendung<br>"Beschaltung"<br>Scheinwiderstand<br>Rastermaß|



Please read _Cautions and warnings_ and _Important notes_ at the end of this document. 

Page 17 of 19 

## **Important notes** 

The following applies to all products named in this publication: 

1. Some parts of this publication contain **statements about the suitability of our products for certain areas of application** . These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out **that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application** . As a rule, we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 

2. We also point out that **in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified** . In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 

3. **The warnings, cautions and product-specific notes must be observed.** 

4. In order to satisfy certain technical requirements, **some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous)** . Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 

5. We constantly strive to improve our products. Consequently, **the products described in this publication may change from time to time** . The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also **reserve the right to discontinue production and delivery of products** . Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 

6. Unless otherwise agreed in individual contracts, **all orders are subject to our General Terms and Conditions of Supply** . 

Page 18 of 19 

## **Important notes** 

7. **Our manufacturing sites serving the automotive business apply the IATF 16949 standard.** The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that **only requirements mutually agreed upon can and will be implemented in our Quality Management System.** For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 

8. The trade names EPCOS, CarXield, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, ModCap, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap, XieldCap are **trademarks registered or pending** in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. 

Release 2020-06 

Page 19 of 19