AWVC002016121R0M00

## **Power Inductor** 

## **Automotive Grade AWVC Series** 

## **Overview** 

Power inductors are passive electronic components used in various circuits to store energy in a magnetic field when electrical current flows through them. They are critical in filtering, energy storage, and noise suppression in power electronic systems. 

They are designed to handle higher currents and are optimized for minimal power loss and thermal efficiency. 

## **Benefits** 

1. Automotive grade available 

2. No thermal aging 

3. High current and efficiency, Magnetic epoxy sealing(Seme-shield) 

## **Applications** 

1. Automotive Systems for Infotainment, MCU, Dashboard, CCD Module 

2. Media player, Audio class 

3. Net working, LCD Panel/TV, 

4. Base stations, 5G infrastructure, and signal processing systems. 

5. Telematics 

## **Product Information** 

|**Series**|**L (mm)**|**W(mm)**|**T (mm)**|**Inductance (**µ**H)**|
|---|---|---|---|---|
|AWVC|2.0|1.6|1.0|0.24 ~ 220|
||2.0|1.6|1.2||
||2.5|2.0|1.2||
||4.0|4.0|1.9||
||5.0|5.0|4.0||
||6.0|6.0|2.8||
||6.0|6.0|4.2~4.7||



**AWVC00201612 Series Specification** AEC-Q200 

**1 Scope:** This specification applies to Wire Wound Power Inductors ~~_|~~ 

## **2[Part Numbering: ]** 

**==> picture [66 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
3 Rating:<br>_|<br>**----- End of picture text -----**<br>


Operating Temperature: －４０℃ ~ １２５℃(Including self - temperature rise) 

Storage Temperature: －４０℃ ~ １２５℃ (The storage temperature range is for after the assembly) 

**==> picture [74 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
4 Marking:<br>_|<br>**----- End of picture text -----**<br>


## **5[Standard Testing Condition]** 

||Unless otherwise specified|In case of doubt|
|---|---|---|
|Temperature|OrdinaryTemperature(15 to 35℃)|20 to 30℃|
|Humidity|OrdinaryHumidity(25 to 85%RH)|50 to 80%RH|



AEC-Q200 

## **AWVC00201612 Series Specification** 

## **6 Configuration and Dimensions:** 

## **7 Electrical Characteristics:** 

|**Part No.**|**Inductance**|**Test Freq.**|**RDC**|**Isat(mA)**|**Irms(mA)**|**Tolerance**|**Marking**|
|---|---|---|---|---|---|---|---|
||**(uH)**||**(Ω)±30%**|**Typ.(Max)**|**Typ.(Max)**|**(±%)**||
|AWVC00201612R50□00|0.5|1MHz,200mV|0.051|2600(2300)|2300(2000)|20,30|B|
|AWVC002016121R0□00|1.0|1MHz,200mV|0.083|1900(1700)|1800(1600)|20,30|C|
|AWVC002016122R2□00|2.2|1MHz,200mV|0.159|1300(1200)|1300(1200)|20,30|E|
|AWVC002016123R3□00|3.3|1MHz,200mV|0.22|1100(990)|1000(950)|20,30|F|
|AWVC002016124R7□00|4.7|1MHz,200mV|0.33|920(820)|900(810)|20,30|G|
|AWVC00201612100□00|10|1MHz,200mV|0.58|620(550)|580(520)|20,30|I|
|AWVC00201612150□00|15|1MHz,200mV|0.9|480(430)|450(400)|20,30|J|
|AWVC00201612220□00|22|1MHz,200mV|1.4|400(360)|400(360)|20,30|K|



## **NOTE: □-tolerance   M=±20% / T=±30%** 

1.Operating temperature range －４０℃ ~ １２５℃(Including self - temperature rise) 2.Isat for Inductance drop 30% from its value without current. 

3.Irms for a 40℃ temperature rise from 25℃ ambient. 

**AWVC00201612 Series Specification** 

AEC-Q200 

**8 AWVC00201612 Series** ~~_|~~ 

**8.1 Construction:** 

## **8.2 Material List:** 

**AWVC00201612 Series Specification** AEC-Q200 

|**AWVC00201612 Series Specification**|AEC-Q200|
|---|---|
|**9**<br>**Reliability of Wire Wound Power Inductors**||
|**1-1.Mechanical Performance**||
|**Item**<br>**Specification**<br>1-1-1 Board Flex<br>The forces applied on the rightTest device shall be soldered on the substrate<br>conditions must not damage<br>Substrate Dimension: 100x40x1.6mm<br>the terminal electrode and the Deflection: 2.0mm<br>ferrite.<br>Keeping Time: 60 sec<br>**Test Method**<br>[~~[op~~||
|1-1-2 Terminal Strength<br>The chip must not damage theAppendix 1 Note(AEC-Q200-005):Force of 1.8 kg for 60||
|terminal electrode and the<br>seconds.||
|ferrite.||
|1-1-3 Solderability<br>The electrodes shall be at<br>Pre-heating: 150℃, 1min||
|least 95% covered with new<br>Solder Composition: Sn/3.0Ag/0.5Cu||
|solder coating.<br>Solder Temperature: 245±5℃||
|Immersion Time: 4±1sec||
|1-1-4 Resistance to<br>Appearance:No damage<br>Pre-heating: 150℃, 1min||
|Soldering Heat<br>Inductance change shall<br>Solder Composition: Sn/Ag3.0/Cu0.5||
|be within ±10%.<br>Solder Temperature: 260±5℃||
|Immersion Time: 10±1sec||
|1-1-5 Resistance to<br>Solvents<br>There must be no change in<br>Inductors must withstand 6 minutes of alcohol or water.<br>appearance or obliteration of<br>marking.<br>1-1-6 Mechanical Shock<br>The forces applied on the rightPulse shape：Half-sine waveform<br>conditions must not damage<br>Impact acceleration：100 g<br>the terminal electrode and the Pulse duration：6 ms<br>ferrite.<br>Number of shocks：18 shocks (3 shocks for each face)<br>Orientation：Bottom, top, left, right, front and rear faces<br>1-1-7 Vibration<br>Appearance:No damage<br>Vibration waveform: Sine waveform<br>Inductance change shall be<br>Vibration frequency: 10Hz~2000Hz<br>within ±10%.<br>Vibration acceleration: 5g<br>Sweep rate: 0.764386otcave/minute<br>Duration of test: 12 cycles each of 3 orientations<br>20 minutes for each cycle<br>Vibration axes: X,Y & Z<br>**1-2.Environmental Performance**<br>**No**<br>**Item**<br>**Specification**<br>1-2-1 High Temperature<br>Appearance:No damage (for Temperature: 125±3℃<br>Exposure (Storage)<br>microscope of CASTOR MZ-4 Time: 1000hrs<br>20X)Inductance change shall Measured after exposure in the room condition for 24hrs<br>be within ±10%.<br>1-2-2 Operational Life<br>Temperature: 125±2℃<br>Appliend Current : Rated Current<br>Time: 1000± 24 hrs<br>Measured after exposure in the room condition for 24hrs<br>1-2-3 Biased Humidity<br>Temperature: 85±2℃<br>Relative Humidity: 85%<br>Time: 1000hrs<br>Measured after exposure in the room condition for 24hrs<br>1-2-4 Temperature Cycling<br>Total cycles: 1000 cycles<br>Temperature Cycling Test Conditions : -40 to +125℃<br>Soak Mode Condition :  30 minutes<br>Measured after exposure in the room condition for 24hrs<br>1-2-5 ESD<br>Test mode：Contact Discharge<br>Discharge level：±6KV, Discharge interval：1 second<br>Polarity of the output voltage：Positive and negative<br>Number of discharge：Discharge +/- for 1 time for the 2 test<br>points.<br>Test Mode：Air Discharge<br>Discharge level：±12KV, ±16KV, ±25KV<br>Discharge interval：＜5 seconds<br>Polarity of the output voltage：Positive and negative<br>Number of discharge：Discharge +/- for 1 time for the 1~2 test<br>points.<br>**Test Method**<br>~~Co~~<br>~~jf~~<br>~~|~~<br>~~sn~~<br>nn<br>~~— oo~~<br>~~— ——~~<br>is~~oe~~||



**==> picture [374 x 15] intentionally omitted <==**

**----- Start of picture text -----**<br>
AWVC00201612 Series Specification AEC-Q200<br>**----- End of picture text -----**<br>


AEC-Q200 

## **AWVC00201612 Series Specification** 

## ~~__|~~ **10 Packaging: 10.1** ~~**Packaging -Cover ta**~~ **p** ~~**e**~~ 

The force for tearing off cover tape is 10 to 100 grams in the arrow direction. 

**==> picture [279 x 149] intentionally omitted <==**

**----- Start of picture text -----**<br>
Top cove r tape<br>C ar ri er tape<br>Sprocket hole<br>Cavity (chip insert)<br>160 ~ 180 [。]<br>7 ” a Top cover tape<br>ajaiaye \ Base tape<br>**----- End of picture text -----**<br>


## **10.2 Packaging Quantity** 

## **10.3 Reel Dimensions** 

AEC-Q200 

## **AWVC00201612 Series Specification** 

## ~~__|~~ **10 Packaging:** 

## **10.4 Tape Dimensions in mm** 

## **11 Recommended Land Pattern:** ~~__|~~ 

## **12 Note:** ~~__|~~ 

1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 

2. Do not knock nor drop. 

3. All the items and parameters in this product specification have been prescribed on the premise that 

our product is used for the purpose,under the condition and in the environment agreed upon between you and us. You are requested not to use our product deviating from  such agreement. 

- 4.The storage period is less than 12 months. Be sure to follow the storage conditions 

(Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). 

If the storage period elapses, the soldering of the terminal   electrodes may deteriorate. 

- 5.Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). 

6. The moisture sensitivity level (MSL) of products is classified as level 1. 

AEC-Q200 

## **AWVC00201612 Series Specification** 

**==> picture [509 x 437] intentionally omitted <==**

**----- Start of picture text -----**<br>
12 Note:<br>__|<br>7. Void Appearance tolerance Limit<br>A<br>Exposed wire tolerance limit of coating resin part on product side.<br>es The unilateral should be no more than two holes.<br>ae<br>A≦ W/2 GOOD<br>A ＞W/2 NG<br>The appearance standard pf the chipping size in top side.<br>Vv<br>B B≦ W/5 GOOD<br>W<br>B ＞W/5 NG<br>j |<br>External appearance criterion for exposed wire<br>Exposed end of the winding wire at  the  side should be acceptable.<br>**----- End of picture text -----**<br>


**==> picture [451 x 18] intentionally omitted <==**

**----- Start of picture text -----**<br>
AWVC00201612 Series Specification AEC-Q200<br>**----- End of picture text -----**<br>


**==> picture [215 x 21] intentionally omitted <==**

**----- Start of picture text -----**<br>
13 Graph: AWVC00201612 Series Graph<br>_|<br>**----- End of picture text -----**<br>


**AWVC00201612 Series Specification** AEC-Q200