AWCU00453228201XTE

## **EMI Common Mode Choke Automotive Grade AWCU Series** 

## **Overview** 

An EMI common mode choke (CMC) for power lines is a passive component specifically designed to suppress electromagnetic interference (EMI) in power supply circuits A full series of common mode choke is designed for excellent noise attenuation with compact sizing for use in wide range of applications. Both standard series and custom designs are available. 

## **Benefits** 

1. Automotive signal Line Common Mode Filter 

2. Automotive CAN Bus Systems 

3. Designed according the IEEE802.3 and IEC6228-3 standard 

4. Operating temperature range `－` 50℃ ～ 150℃ 

## **Applications** 

1. Automotive CAN Bus Systems 

2. EMI solutions for charger 

3. LVDS 

4. Networking 

## **Product Information** 

**Series Size Code (JIS/EIA) Impedance(Ω)** AWCU 2012/0805 30 ~ 6500 3216/1206 3325/1210 4532/1812 

AEC-Q200 

## **AWCU00453228 Series Specification** 

**1 Scope:** This specification applies to AWCU Wire Wound Common Mode Choke Coil ~~_|~~ 

**==> picture [122 x 21] intentionally omitted <==**

**----- Start of picture text -----**<br>
2 [Part Numbering: ]<br>_|<br>**----- End of picture text -----**<br>


## **3 Rating:** ~~_|~~ 

Operating Temperature:     - 50 ℃ ~ 150 ℃ 

(Including self - temperature rise) 

Storage Temperature: - 40 ℃ ~ 125 ℃ (The storage temperature range is for after the assembly) 

**==> picture [75 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
4 Marking:<br>_|<br>**----- End of picture text -----**<br>


**==> picture [97 x 17] intentionally omitted <==**

**----- Start of picture text -----**<br>
No   Marking<br>**----- End of picture text -----**<br>


**==> picture [182 x 22] intentionally omitted <==**

**----- Start of picture text -----**<br>
5 [Standard Testing Condition]<br>_|<br>**----- End of picture text -----**<br>


||Unless otherwise specified|In case of doubt|
|---|---|---|
|Temperature|OrdinaryTemperature(15 to 35℃)|20 to 30℃|
|Humidity|OrdinaryHumidity(25 to 85% RH)|50 to 80 %RH|



AEC-Q200 

## **AWCU00453228 Series Specification** 

## **6 Configuration and Dimensions and Unit Weight:** 

Polarity Equivalent circuit 

## **7 Electrical Characteristics:** 

||||||**Rated**|**Insulation**|
|---|---|---|---|---|---|---|
|**Part No.**|**L**|**Test Freq.**|**RDC**|**Irms**|**Voltage**|**Resistance**|
||**(uH)+50%-20%**|**(KHz)**|**(Ω)Max.**|**(mA)Max.**|**(Vdc)Max.**|**(MΩ)Min.**|
|AWCU00453228201XTE|200|100kHz,0.1V|4.5|100|50|10|



**NOTE:** □ **-tolerance X=+50%-20%** 

1.Operating temperature range －5 0℃ ~ 150℃(Including self - temperature rise) 

2.L(Common mode inductance ) Test Frequency : 100kHz,0.1V 

3.RDC: SINGLE WIRE TEST VALUE 

4.Irms for a 15 ℃ temperature rise from 25 ℃ ambient. 

**AWCU00453228 Series Specification** AEC-Q200 

**==> picture [401 x 250] intentionally omitted <==**

**----- Start of picture text -----**<br>
8 AWCU00453228 Series<br>_ |<br>8.1 Construction:<br>3<br>1<br>4<br>2<br>**----- End of picture text -----**<br>


## **8.2 Material List:** 

**==> picture [279 x 191] intentionally omitted <==**

**----- Start of picture text -----**<br>
ITEM PART DESCORIPTION<br>1 WIRE Grade  180<br>2 TERMINAL Ag/Cu/Ni/Sn<br>3 CORE FERRITE CORE<br>4 COVER SHEET FERRITE CORE<br>**----- End of picture text -----**<br>


AEC-Q200 

## **AWCU00453228 Series Specification** 

|**9**<br>**Reliability of Common Mode Choke**|||
|---|---|---|
|**1-1.Mechanical Performance**|||
|**Item**<br>**Specification**<br>1-1-1 Board Flex<br>The forces applied on the rightTest device shall be soldered on the substrate<br>conditions must not damage<br>Substrate Dimension: 100x40x1.6mm<br>the terminal electrode and the Deflection: 2.0mm<br>ferrite.<br>Keeping Time: 60 sec<br>1-1-2 Terminal Strength<br>The chip must not damagetheAppendix 1 Note(AEC-Q200-005):Force of 2Lbs for 60<br>terminal electrode and the<br>seconds.<br>ferrite.<br>1-1-3 Solderability<br>The electrodes shall be at<br>Pre-heating: 150℃, 1min<br>least 95% covered with new<br>Solder Composition: Sn/3.0Ag/0.5Cu<br>solder coating.<br>Solder Temperature: 245±5℃<br>Immersion Time: 4±1sec<br>**TestMethod**<br>~~>?~~<br>~~{of~~<br>~~|~~<br>~~wee~~<br>~~a~~|||
|1-1-4 Resistance to<br>Appearance:No damage|Pre-heating: 150℃, 1min||
|Soldering Heat<br>Inductance change shall|Solder Composition: Sn/Ag3.0/Cu0.5||
|be within ±20%.|Solder Temperature: 260±5℃||
||Immersion Time: 10±1sec||
|1-1-5 Resistance to<br>Solvents<br>There must be no change in<br>Inductors must withstand 6 minutes of alcohol or water.<br>appearance or obliteration of<br>marking.<br>1-1-6 Mechanical Shock<br>The forces applied on therightPulse shape：Half-sine waveform<br>conditions must not damage<br>Impact acceleration：100 g<br>the terminal electrode and the Pulse duration：6 ms<br>ferrite.<br>Number of shocks：18 shocks (3 shocks for each face)<br>Orientation：Bottom, top, left, right, front and rear faces<br>1-1-7 Vibration<br>Appearance:No damage<br>Vibration waveform: Sine waveform<br>Inductance change shall be<br>Vibration frequency: 10Hz~2000Hz<br>within ±20%.<br>Vibration acceleration: 5g<br>Sweep rate: 0.764386otcave/minute<br>Duration of test: 12 cycles each of 3 orientations<br>20 minutes for each cycle<br>Vibration axes: X,Y & Z<br>**1-2.Environmental Performance**<br>**No**<br>**Item**<br>**Specification**<br>1-2-1 High Temperature<br>Temperature: 150±3℃<br>Exposure (Storage)<br>Time: 1000hrs<br>Appearance:No damage (for Measured after exposure in the room condition for 24hrs<br>**Test Method**<br>~~coe~~<br>~~jj] |~~<br>~~a~~|||
|1-2-2 Low Temperature<br>microscope of CASTOR MZ-4<br>Exposure (Storage)<br>20X)Inductance change shall Temperature: -50±3℃<br>be within ±10%.<br>Time: 1000hrs<br>Q change:within±30% of<br>Measured after exposure in the room condition for 24hrs<br>~~a~~|||
|1-2-2 Operational Life<br>initial value<br>~~ee~~|Temperature: 150±2℃<br>Appliend Current : Rated Current<br>Time: 1000± 24 hrs<br>Measured after exposure in the room condition for 24hrs||
|1-2-3 Biased Humidity<br>~~ee~~|Temperature: 85±2℃<br>Relative Humidity: 85%<br>Time: 1000hrs<br>Measured after exposure in the room condition for 24hrs||
|1-2-4 Temperature Cycling|Total cycles: 1000 cycles||
||Temperature Cycling Test Conditions : -50 to +150℃||
|Appearance:No damage|Soak Mode Condition :  30 minutes||
|Inductance change shall|Measured after exposure in the room condition for 24hrs||
|1-2-5 ESD<br>be within ±10%.|Test mode：Contact Discharge||
||Discharge level：±6KV, Discharge interval：1 second||
||Polarity of the output voltage：Positive and negative||
||Number of discharge：Discharge +/- for 1 time for the 2 test||
||points.||
||Test Mode：Air Discharge||
||Discharge level：±12KV, ±16KV, ±25KV||
||Discharge interval：＜5 seconds||
||Polarity of the output voltage：Positive and negative||
||Number of discharge：Discharge +/- for 1 time for the 1~2 test||
||points.||



**AWCU00453228 Series Specification** AEC-Q200 

AEC-Q200 

## **AWCU00453228 Series Specification** 

**==> picture [481 x 48] intentionally omitted <==**

**----- Start of picture text -----**<br>
10 Packaging:<br>_|<br>10.1 Packaging -Cover Tape<br>The force for tearing off cover tape is 10 to 130 grams in the arrow direction.<br>**----- End of picture text -----**<br>


**==> picture [165 x 64] intentionally omitted <==**

**----- Start of picture text -----**<br>
10.2 Packaging Quantity<br>TYPE PCS/REEL<br>453228 2500<br>**----- End of picture text -----**<br>


**==> picture [417 x 103] intentionally omitted <==**

**----- Start of picture text -----**<br>
10.3 Reel Dimensions<br>A,<br>Dimensions in mm<br>/ | : TYPE A B C D<br>453228 330 100 13 13.4<br>**----- End of picture text -----**<br>


AEC-Q200 

## **AWCU00453228 Series Specification** 

**==> picture [439 x 284] intentionally omitted <==**

**----- Start of picture text -----**<br>
10 Packaging:<br>_|<br>10.4 Tape Dimensions in mm<br>tseelbe i fo<br>YEE -<br>TYPE A0 B0 K0 D E F W P P0 P2<br>453228 3.6 4.9 3.3 1.50 1.75 5.5 12 8 4 2<br>a<br>11 Recommended Land Pattern:<br>_|<br>**----- End of picture text -----**<br>


## Dimensions in mm 

|**TYPE**|**F**|**G**|**H**|**I**|
|---|---|---|---|---|
|**453228**|0.7|2.1/3.2|3.5|5.9|



- **12 Note:** 

- ~~_|~~ 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 

   2. Do not knock nor drop. 

   3. All the items and parameters in this product specification have been prescribed on the premise that our product is used for the purpose,under the condition and in the environment agreed upon between you and us. You are requested not to use our product deviating from  such agreement. 

   - 4.The storage period is less than 12 months. Be sure to follow the storage conditions 

   - (Temperature: 5 to 40°C, Humidity: 10 to 75% RHor less). 

If the storage period elapses, the soldering of the terminal   electrodes may deteriorate. 

- 5.Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). 

6. The moisture sensitivity level (MSL) of products is classified as level 1. 

**AWCU00453228 Series Specification** 

AEC-Q200 

## **13 Graph: AWCU00453228201XTE** 

**==> picture [426 x 282] intentionally omitted <==**

**----- Start of picture text -----**<br>
100000<br>COMMON MODE<br>em<br>10000 rece<br>ee<br>1000 EE<br>PN<br>100<br>po ANENA<br>Pee ee ee<br>10 DIFFERENTIAL   MODE<br>a ee eee<br>PoE<br>1 ee en 0<br>1 10 100 1000 10000<br>FREQUENCY(MHz)<br>IMPEDANCE(Ω)<br>**----- End of picture text -----**<br>