AWCU00332523101XT2

## **EMI Common Mode Choke Automotive Grade AWCU Series** 

## **Overview** 

An EMI common mode choke (CMC) for power lines is a passive component specifically designed to suppress electromagnetic interference (EMI) in power supply circuits A full series of common mode choke is designed for excellent noise attenuation with compact sizing for use in wide range of applications. Both standard series and custom designs are available. 

## **Benefits** 

1. Automotive signal Line Common Mode Filter 

2. Automotive CAN Bus Systems 

3. Designed according the IEEE802.3 and IEC6228-3 standard 

4. Operating temperature range `－` 50℃ ～ 150℃ 

## **Applications** 

1. Automotive CAN Bus Systems 

2. EMI solutions for charger 

3. LVDS 

4. Networking 

## **Product Information** 

**Series Size Code (JIS/EIA) Impedance(Ω)** AWCU 2012/0805 30 ~ 6500 3216/1206 3325/1210 4532/1812 

AEC-Q200 

## **AWCU00332523 Series Specification** 

**1 Scope:** This specification applies to AWCU Wire Wound Common Mode Choke Coil ~~_|~~ 

**==> picture [122 x 21] intentionally omitted <==**

**----- Start of picture text -----**<br>
2 [Part Numbering: ]<br>_|<br>**----- End of picture text -----**<br>


**==> picture [66 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
3 Rating:<br>_|<br>**----- End of picture text -----**<br>


Operating Temperature:     - 50 ℃ ~ 150 ℃ (Including self - temperature rise) Storage Temperature: - 40 ℃ ~ 125 ℃ 

(The storage temperature range is for after the assembly) 

**==> picture [75 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
4 Marking:<br>_|<br>**----- End of picture text -----**<br>


**==> picture [97 x 16] intentionally omitted <==**

**----- Start of picture text -----**<br>
No   Marking<br>**----- End of picture text -----**<br>


**==> picture [182 x 22] intentionally omitted <==**

**----- Start of picture text -----**<br>
5 [Standard Testing Condition]<br>_|<br>**----- End of picture text -----**<br>


||Unless otherwise specified|Incase ofdoubt|
|---|---|---|
|Temperature|OrdinaryTemperature(15to 35℃)|20 to 30℃|
|Humidity|OrdinaryHumidity(25to 85%RH)|50to 80 %RH|



AEC-Q200 

## **AWCU00332523 Series Specification** 

## **6 Configuration and Dimensions and Unit Weight:** 

## **7 Electrical Characteristics:** 

||||**Stary**|||**Insulation**|**Rated**||
|---|---|---|---|---|---|---|---|---|
|**Part No.**|**Z(Ω)**|**L(uH)**|**Inductance**|**RDC**|**Irms**|**Resistance**|**Voltage**|**Tolerance**|
||**Min.(Typ.)**|**+50/-30%**|**(uH)Typ.**|**(Ω)Max.**|**(mA)Max.**|**(MΩ)Min.**|**(Vdc)Max.**|**(±%)**|
|AWCU00332523110□T2|300(550)|11|0.05|0.4|300|10|80|X,T|
|AWCU00332523220□T2|500(1100)|22|0.06|0.5|250|10|80|X,T|
|AWCU00332523510□T2|1000(2600)|51|0.09|0.7|200|10|80|X,T|
|AWCU00332523101□T2|2200(5100)|100|0.13|1.5|150|10|80|X,T|



**NOTE:** □ **-tolerance: tolerance X=+50%/-30% /  T= +30%/-30%** 

1.Operating temperature range －５０℃ ~ １５０℃(Including self - temperature rise) 

2.Z Test Frequency : 10MHz,0.1V 

3.L Test Frequency : 100kHz,0.1V 

4.Stary Inductance :  100kHz,0.1V 

5.RDC: SINGLE WIRE TEST VALUE 

6.Irms for a 15 ℃ temperature rise from 25 ℃ ambient. 

7.weight: 0.039(g) typ. 

**AWCU00332523 Series Specification** 

AEC-Q200 

**8 AWCU00332523 Series** ~~|~~ **8.1 Construction:** 

## **8.2 Material List:** 

|NO|PART|MATERIAL|
|---|---|---|
|1|WIRE|Grade 180|
|2|COVER SHEET|FERRITE CORE|
|3|CORE|FERRITE CORE|
|4|TERMINAL|Ag/Cu/Ni/Sn|



AEC-Q200 

## **AWCU00332523 Series Specification** 

|**AWCU00332523 Series Specification**|AEC-Q200|
|---|---|
|**9**<br>**Reliability of Common Mode Choke**||
|**1-1.Mechanical Performance**<br>**Item**<br>**Specification**<br>1-1-1 Board Flex<br>The forces applied on the right Test device shall be soldered on the substrate<br>conditions must not damage<br>Substrate Dimension: 100x40x1.6mm<br>the terminal electrode and the Deflection: 2.0mm<br>ferrite.<br>Keeping Time: 60 sec<br>1-1-2 Terminal Strength<br>The chip must not damagethe Appendix 1 Note(AEC-Q200-005):Force of 2Lbs for 60<br>terminal electrode and the<br>seconds.<br>ferrite.<br>1-1-3 Solderability<br>The electrodes shall be at<br>Pre-heating: 150℃, 1min<br>least 95% covered with new<br>Solder Composition: Sn/3.0Ag/0.5Cu<br>solder coating.<br>Solder Temperature: 245±5℃<br>Immersion Time: 4±1sec<br>**TestMethod**<br>~~eefof~~<br>~~nee~~<br>~~a~~||
|1-1-4 Resistance to<br>Appearance:No damage<br>Pre-heating: 150℃, 1min||
|Soldering Heat<br>Inductance change shall<br>Solder Composition: Sn/Ag3.0/Cu0.5||
|be within ±20%.<br>Solder Temperature: 260±5℃||
|Immersion Time: 10±1sec||
|1-1-5 Resistance to<br>There must be no change in<br>Inductors must withstand 6 minutes of alcohol or water.<br>Solvents<br>appearance or obliteration of<br>marking.<br>1-1-6 Mechanical Shock<br>The forces applied on theright Pulse shape：Half-sine waveform<br>conditions must not damage<br>Impact acceleration：100 g<br>the terminal electrode and the Pulse duration：6 ms<br>ferrite.<br>Number of shocks：18 shocks (3 shocks for each face)<br>Orientation：Bottom, top, left, right, front and rear faces<br>1-1-7 Vibration<br>Appearance:No damage<br>Vibration waveform: Sine waveform<br>Inductance change shall be<br>Vibration frequency: 10Hz~2000Hz<br>within ±20%.<br>Vibration acceleration: 5g<br>Sweep rate: 0.764386otcave/minute<br>Duration of test: 12 cycles each of 3 orientations<br>20 minutes for each cycle<br>Vibrationaxes: X,Y&Z<br>**1-2.Environmental Performance**<br>**No**<br>**Item**<br>**Specification**<br>1-2-1 High Temperature<br>Appearance:No damage (for<br>Temperature: 150±3℃<br>Exposure (Storage)<br>microscope of CASTORMZ-45 Time: 1000hrs<br>20X)Inductance change shall<br>Measured after exposure in the room condition for 24hrs<br>be within ±20%.<br>1-2-2 Low Temperature<br>Temperature: -50±3℃<br>Exposure (Storage)<br>Time: 1000hrs<br>Measured after exposure in the room condition for 24hrs<br>**Test Method**<br>~~a~~<br>~~|] |~~<br>~~eeee~~||
|1-2-3 Biased Humidity<br>Temperature: 85±2℃<br>Relative Humidity: 85%<br>Time: 1000hrs<br>Measured after exposure in the room condition for 24hrs<br>~~ee~~||
|1-2-4 Temperature Cycling<br>Total cycles: 1000 cycles<br>Temperature Cycling Test Conditions : -50 to +150℃<br>Soak Mode Condition :  30 minutes<br>Measured after exposure in the room condition for 24hrs<br>~~ee~~||
|1-2-5 Operational Life<br>Temperature: 150±2℃<br>Appliend Current : Rated Current<br>Time: 1000± 24 hrs<br>Measured after exposure in the room condition for 24hrs<br>1-2-6 ESD<br>Test mode：Contact Discharge<br>Discharge level：±6KV, Discharge interval：1 second<br>Polarity of the output voltage：Positive and negative<br>Number of discharge：Discharge +/- for 1 time for the 2 test<br>points.<br>Test Mode：Air Discharge<br>Discharge level：±12KV, ±16KV, ±25KV<br>Discharge interval：＜5 seconds<br>Polarity of the output voltage：Positive and negative<br>Number of discharge：Discharge +/- for 1 time for the 1~2 test<br>points.<br>~~T~~||



**==> picture [377 x 341] intentionally omitted <==**

**----- Start of picture text -----**<br>
AWCU00332523 Series Specification AEC-Q200<br>°C Ramp-up Pre-heating Ref low Cooling<br>300 RE FRE iF OP<br>Reak 260°C<br>250 ams—- Ramp-down<br>"te<br>150 150-200°C<br>Ramp-up<br>100 3°C/sec max<br>50<br>sce<br>0 50 100 150 200 250 300 350<br>Reflow profile<br>Lead-Free(LFIDR#RB ED REA Refer to J-STD-020C<br>Item. Ramp-up Pre-heating Reflow Peak Temp ‘Cooling<br>| Se | ces, || cae |e |<br>Temp.scope<br>spec.<br>oeTime edcd de<br>Time result<br>NOTE: NOTE:<br>1.Re-flow possible times : within 3 times<br>2.Nitrogen 1.Re-flow possible times: within 2times adopted is recommendes while in re-flow<br>3.Products 2.Nitrogen adopted is recommended while in re-flow can only be soldered with reflow<br>**----- End of picture text -----**<br>


AEC-Q200 

## **AWCU00332523 Series Specification** 

## **10 Packaging:** ~~_|~~ **10.1 Packaging -Cover Tape** 

The force for tearing off cover tape is 10 to 130 grams in the arrow direction. 

## **10.2 Packaging Quantity** 

**==> picture [144 x 32] intentionally omitted <==**

**----- Start of picture text -----**<br>
TYPE PCS/REEL<br>332523 1500<br>**----- End of picture text -----**<br>


**==> picture [423 x 156] intentionally omitted <==**

**----- Start of picture text -----**<br>
10.3 Reel Dimensions<br>Dimensions in mm<br>TYPE A B C D<br>332523 178±1 60±0.5 16±0.5 1.4±0.5<br>——<br>5<br>oe ==="<br>**----- End of picture text -----**<br>


**AWCU00332523 Series Specification** 

AEC-Q200 

**==> picture [436 x 218] intentionally omitted <==**

**----- Start of picture text -----**<br>
10 Packaging:<br>__|<br>10.4 Tape Dimensions in mm<br>a ” § Tape Material<br>oe pe za\ER caeikae<br>TSEIREINETED fealacelt<br>TYPE A B D E F H I P P0 P2<br>332523 12 2.72 3.52 5.5 1.75 2.45 0.25 4 4 2<br>**----- End of picture text -----**<br>


## **11 Recommended Land Pattern:** ~~__|~~ 

**==> picture [490 x 297] intentionally omitted <==**

**----- Start of picture text -----**<br>
Dimensions in mm<br>TYPE F G H I<br>332523 0.4 1.6/2.5 2 4.1<br>aia<br>nh<br>12 Note:<br>__|<br>1. Please make sure that your product has been evaluated and confirmed against your specifications<br>    when our product is mounted to your product.<br>2. Do not knock nor drop.<br>3. All the items and parameters in this product specification have been prescribed on the premise that<br>    our product is used for the purpose,under the condition and in the environment agreed upon between<br>    you and us. You are requested not to use our product deviating from  such agreement.<br>4.The storage period is less than 12 months. Be sure to follow the storage conditions<br>    (Temperature: 5 to 40°C, Humidity: 10 to 75% RHor less).<br>  If the storage period elapses, the soldering of the terminal   electrodes may deteriorate.<br>5.Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).<br>6. The moisture sensitivity level (MSL) of products is classified as level 1.<br>**----- End of picture text -----**<br>


AEC-Q200 

## **AWCU00332523 Series Specification** 

## **13 Graph:**