AMT45S-150-2P-TL000

**Pulse Transformers Pulse Transformers for PLC Communication AMT series** 

## **AMT45S type** 

## **■FEATURES** 

◯This is a pulse transformer for PLC communication that supports an operating temperature range of -40 to +125°C. 

◯This product achieves low insertion loss while ensuring high reliability through the use of metal terminals and laser welding, enabled by a proprietary manufacturing method. 

◯Compliant with AEC-Q200 

## **■APPLICATION** 

◯Charging Control Circuit (PLC) for xEV Compliant with HomePlug Green PHY 

## **■PART NUMBER CONSTRUCTION** 

**==> picture [327 x 45] intentionally omitted <==**

**----- Start of picture text -----**<br>
- - -<br>AMT45S 150 2P TL 000<br>Inductance(min.) Number of Packaging Internal<br>Series - type name<br>(μH) lines style code<br>**----- End of picture text -----**<br>


## **■CHARACTERISTICS SPECIFICATION TABLE** 

|**Inductance**|**DC resistance**|**Withstand Voltage**|**Withstand Voltage**|**Insulation**|**Rated Voltage Between**|**Input Signal**<br>**Secondary**|**Input Signal**<br>**Secondary**|**Part No.**|
|---|---|---|---|---|---|---|---|---|
|||||**resistance**|**Primary and Secondary**|**Voltage**|**Load Current**||
|||**[AC] 60sec.**|**[AC] 60sec.**|**[DC] 1kV**|**[DC]**|**[AC]**|**[AC]**||
|**(μH)min.**|**(Ω)max.**|**(Vrms)**||**(MΩ)min.**|**(V)max.**|**(Vp-p)max.**|**(mArms)max.**||
|15.0|1.0|500||10|50|10|10|AMT45S-150-2P-TL000|
|**Measurement equipment**|||||||||
|**Measurement item**|||**Product No. ***||**Manufacturer**||||
|Inductance|||4294A||Keysight Technologies||||
|DC resistance|||4338A||Keysight Technologies||||
|Withstand Volta|Withstand Voltage||TOS9201||KIKUSUI Electronics||||
|Insulation resistance|Insulation resistance||4339B||Keysight Technologies||||



* Equivalent measurement equipment may be used. 

(1/4) 

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 

20251112 

trans_amt45s_en 

## **AMT45S type** 

## **■INSERTION LOSS VS. FREQUENCY CHARACTERISTICS(Reference Characteristics)** 

**==> picture [497 x 232] intentionally omitted <==**

**----- Start of picture text -----**<br>
0<br>–1<br>–2<br>–3<br>–4<br>–5<br>0.1 1 10 100<br>Frequency (MHz)<br>Insertion loss Sdd21 (dB)<br>**----- End of picture text -----**<br>


## **Measurement equipment** 

|**Product No. ***|**Manufacturer**|
|---|---|
|5071C|Keysight Technologies|



- Equivalent measurement equipment may be used. 

## **■TEMPERATURE RANGE, INDIVIDUAL WEIGHT** 

|**Operating**<br>**temperature range**|**Storage**<br>**temperature range ***|**Individual**<br>**weight**|
|---|---|---|
|-40 to +125 °C|-40 to +125 °C|0.14g|



* The storage temperature range is for after the assembly. 

(2/4) 

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 

20251112 trans_amt45s_en 

## **AMT45S type** 

## **■SHAPE & DIMENSIONS** 

## **■PACKAGING STYLE** 

## □ **REEL DIMENSIONS** 

**==> picture [151 x 415] intentionally omitted <==**

**----- Start of picture text -----**<br>
3.2±0.2<br>1 2<br>4 3<br>0.65±0.1 0.7±0.1<br>Dimensions in mm<br>■RECOMMENDED LAND PATTERNRECOMMENDED LAND PATTERN<br>3.4<br>1.6<br>( Eu<br>Dimensions in mm<br>■CIRCUIT DIAGRAM<br>1 2<br>4 3<br>• No polarity<br>0.24.5±<br>0.22.8±<br>5.9 3.2<br>**----- End of picture text -----**<br>


**==> picture [167 x 169] intentionally omitted <==**

**----- Start of picture text -----**<br>
2.0±0.5 (2)<br>ø13.0+0.3/-0.2 13.5±0.5<br>(ø21)<br>ø330+2.0/-2.5<br>ø100+1.0/-1.5<br>**----- End of picture text -----**<br>


## **■RECOMMENDED LAND PATTERNRECOMMENDED LAND PATTERN** 

Dimensions in mm 

## □ **TAPE DIMENSIONS** 

**==> picture [253 x 253] intentionally omitted <==**

**----- Start of picture text -----**<br>
Sprocket<br>0.3±0.05 1.55±0.05 2.0±0.05 4.0±0.1 hole<br>5 K aaaaaaa A Cavity<br>LJ Le 8.0±0.1<br>Dimensions in mm<br>Type A B K<br>ei AMT45S (3.6) (4.9) (3.05)<br>Blank Products Blank<br>160min. 750min<br>Start End<br>Drawing direction<br>Dimensions in mm<br>5.5±0.05<br>1.75±0.1<br>B<br>12.0±0.2<br>**----- End of picture text -----**<br>


**■RECOMMENDED REFLOW PROFILE** 

**==> picture [517 x 219] intentionally omitted <==**

**----- Start of picture text -----**<br>
Dimensions in mm<br>Preheating Soldering Natural<br>cooling<br>Peak □ PACKAGE QUANTITY<br>245°C Package quantity 2,500 pcs/reel<br>230°C 230°C<br>180°C<br>5s max.<br>150°C<br>60 to 120s 10 to 30s<br>B N _———~~<br>Time<br>Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. (3/4)<br>$$<br>Please note that the contents may change without any prior notice due to reasons such as upgrading.<br>Temperature<br>**----- End of picture text -----**<br>


20251112 

trans_amt45s_en 

## **REMINDERS FOR USING THESE PRODUCTS** 

Before using these products, be sure to request the delivery specifications. 

## **SAFETY REMINDERS** 

Please pay sufficient attention to the warnings for safe designing when using this products 

## **REMINDERS** 

- ◯The storage period is within 12 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 10 to 75% RH or less). 

If the storage period elapses, the soldering of the terminal electrodes may deteriorate. 

- ◯Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). 

- ◯Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. 

- ◯When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. 

- ◯Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. 

- ◯Carefully lay out the coil for the circuit board design of the non-magnetic shield type. 

- A malfunction may occur due to magnetic interference. 

- ◯Use a wrist band to discharge static electricity in your body through the grounding wire. 

- ◯Do not expose the products to magnets or magnetic fields. 

- ◯Do not use products that have received any excessive mechanical shock such as by being dropped. 

- ◯The performance of the product may deteriorate or at the worst case open if coating materials are used, thus please assess the situation beforehand by tak-ing this factor into consideration. 

- ◯Due to the application of mechanical stress after mounting and handling such as contact, disconnection may occur. 

- ◯Do not use for a purpose outside of the contents regulated in the delivery specifications. 

- ◯The products listed on this specification sheet (the “Products”) are intended for incorporation into automobile and/or equipment to be installed in automobile on the grounds that (i) the Products are used in accordance with the conditions and scope stated in this specification sheet and (ii) said automobile and/or equipment involving the Products are used under a normal operation and use condition. 

- Except for said incorporation into automobile and/or equipment installed in automobile, the Products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. Please understand that we are not responsible for any damage or liability caused by use of the Products in any of the applications listed below or for any other use exceeding the range or conditions set forth in this specification sheet. 

If you intend to use the Products beyond the condition and scope of this specification sheet or in any of the applications listed below, please contact with our sales office. 

We will separately discuss with you applicable specification suitable for your intended use. 

- (1) Aerospace/aviation equipment (7) Transportation control equipment 

- (2) Transportation equipment (cars, electric trains, ships, etc.) (8) Public information-processing equipment 

- (3) Medical equipment (9) Military equipment 

(4) Power-generation control equipment (10) Electric heating apparatus, burning equipment 

(5) Atomic energy-related equipment (11) Disaster prevention/crime prevention equipment (6) Seabed equipment (12) Safety equipment 

(13) Other applications that are not considered general-purpose applications 

When designing your equipment involving the Products, you are kindly requested to take into consideration securing protection circuit/equipment or providing backup circuits, etc. in your equipment, to ensure higher safety. 

As stated above, the Products are intended for incorporation into automobile and/or equipment to be installed in automobile, however, it is not prohibited to use the Products for general electronic equipment which is not required the same high level or reliability as automobile, or which is unlikely to damage its users’ life, body and property or to cause extensive impact on society. Accordingly, all description in this specification sheet is applied if the Products are incorporated into general electronic equipment which is used for normal application under a normal operation and use condition. 

(4/4) 

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 

20251112 

trans_amt45s_en