ACM2012-201-2P-T001

November 2013 

## Common Mode Filters 

For automobile signal line 

## ACM series 

***** Dimensions Code JIS[EIA] 

**[0805 inch]*** （ **MOST** ） 

**ACM2012** 

(2/7) 

## **REMINDERS FOR USING THESE PRODUCTS** 

Before using these products, be sure to request the delivery specifications. 

## **SAFETY REMINDERS** 

Please pay sufficient attention to the warnings for safe designing when using these products. 

## **REMINDERS** 

- ~~O~~ The storage period is less than 6 months.  Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. 

~~O~~ Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). 

- ~~O~~ Before soldering, be sure to preheat components. 

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. 

- ~~O~~ Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. 

- ~~O~~ When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. 

- O Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. 

- ~~O~~ Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. 

~~O~~ Use a wrist band to discharge static electricity in your body through the grounding wire. 

~~O~~ Do not expose the products to magnets or magnetic fields. 

~~O~~ Do not use for a purpose outside of the contents regulated in the delivery specifications. 

- ~~O~~ The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. 

   - The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. 

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. 

## (1) Aerospace/Aviation equipment 

- (8) Public information-processing equipment 

(2) Transportation equipment (electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications 

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 

001-01 / 20131101 / e9719_acm2012.fm 

(3/7) 

**Product compatible with RoHS directive Compatible with lead-free solders AEC-Q200** 

## **E M C C o m p o n e n t s** ee **Common Mode Filters For automobile signal line** 

## **Overview of the ACM Series** 

## **FEATURES** 

Highly reliable with a temperature range of –40 to +105°C. Impedance variation: Four impedance values are available for compatibility with various usages. Common mode EMI measure: Possible to suppress waveform common mode EMI without straining the waveform. 

## **APPLICATION** 

Radiated noise suppression for car multimedia interfaces (MOST, USB2.0, IDB-1394, etc.). 

## **PART NUMBER CONSTRUCTION** 

**==> picture [463 x 85] intentionally omitted <==**

**----- Start of picture text -----**<br>
- - -<br>ACM 2012 361 2P T 001<br>SF st '<br>L×W Dimensions Impedance<br>Series name Number of lines Packaging style Internal code<br>(mm) ( ) at 100MHz<br>2012 2.0×1.2 900 90 2P 2 lines T ø180mm reel<br>121 120 TL ø330mm reel<br>201 200<br>361 360<br>**----- End of picture text -----**<br>


## **OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT** 

|**Type**<br>~~.~~|**Temperature range**<br>~~oo~~<br>~~res~~|**Temperature range**<br>~~oo~~<br>~~res~~|**Reel diameter**<br>~~oo~~<br>~~res~~|**Package quantity**<br>~~res~~|**Individual weight**|
|---|---|---|---|---|---|
||**Operating**<br>**temperature**<br>~~res~~|**Storage**<br>**temperature**<br>~~res~~||||
||（**°C**）<br>~~res~~<br>~~ee~~|（**°C**）<br>~~res~~<br>~~ee ee~~|（**mm**）<br>~~res~~<br>~~ee~~|（**pieces/reel**）<br>~~res~~<br>~~eee~~|（**mg**）<br>~~eee~~|
|**ACM2012-XXX-2P-T001**<br>~~.~~|–40 to +105<br>~~ee~~|–40 to +105<br>~~ee ee~~|ø180<br>~~ee~~|2,000<br>~~eee~~|10<br>~~eee~~|
||||ø330<br>~~ee~~|10,000<br>~~eee~~||



RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. 

• All specifications are subject to change without notice. 

001-01 / 20131101 / e9719_acm2012.fm 

(4/7) 

## **Overview of the ACM Series** 

## **RECOMMENDED REFLOW PROFILE** 

||||Preheating|Preheating||Soldering<br>T4<br>Peak|Soldering<br>T4<br>Peak|Soldering<br>T4<br>Peak|Soldering<br>T4<br>Peak|Natural<br>cooling|||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|T:Temperature|T1|||T2|T3||t3|||T3|||
|||||t1|||t2||||||
||||||||||||||
|||||t:Time|||||||||
|**Preheating**|||||**Soldering**||||||**Peak**||
|**Temp.**|||**Time**||**Temp.**|||**Time**|||**Temp.**|**Time**|
|**T1**|**T2**||**t1**||**T3**|||**t2**|||**T4**|**t3**|
|150°C<br>180°C|||60 to 120s|60 to 120s|230°C||10 to 30s||||245°C|5s max.|



• All specifications are subject to change without notice. 

001-01 / 20131101 / e9719_acm2012.fm 

(5/7) 

## **E M C C o m p o n e n t s** ~~—~~ a rt—(_i_iee—”—C— ACM series **ACM2012 Type** taal 

## **SHAPE & DIMENSIONS** 

**==> picture [289 x 149] intentionally omitted <==**

**----- Start of picture text -----**<br>
2.0±0.2<br>0.4 1.2 0.4 Dimensions in mm<br>1.3max.<br>0.3<br>0.2<br>± 0.5<br>1.2<br>0.05 0.3<br>**----- End of picture text -----**<br>


**==> picture [359 x 86] intentionally omitted <==**

**----- Start of picture text -----**<br>
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM<br>1 4<br>2 3<br>=] 5 • No polarity 4<br>0.75 1.1 0.75 Dimensions in mm<br>0.4<br>0.4<br>0.4<br>**----- End of picture text -----**<br>


• All specifications are subject to change without notice. 

001-01 / 20131101 / e9719_acm2012.fm 

(6/7) 

## **E M C C o m p o n e n t s** ~~ee~~ ACM series **ACM2012 Type** 

## **ELECTRICAL CHARACTERISTICS** 

## **CHARACTERISTICS SPECIFICATION TABLE** 

|**Common mode impedance**<br>**(**<br>**) [100MHz]**<br>**min.**|**Common mode impedance**<br>**typ.**|**DC resistance**<br>**(**<br>**)max.**<br>**[1 line]**|**Rated current**<br>**(mA)max.**|**Rated voltage**<br>**(V)max.**|**Part No.**|
|---|---|---|---|---|---|
|65|90|0.19|400|50|ACM2012-900-2P-T001|
|90|120|0.22|370|50|ACM2012-121-2P-T001|
|150|200|0.25|350|50|ACM2012-201-2P-T001|
|270|360|0.50|220|50|ACM2012-361-2P-T001|



- ・Operating temperature range: –40 to +105°C 

- Measurement equipment 

|Measurement item|Measurement item|Product No.|Manufacturer|
|---|---|---|---|
|Common mode impedance||4991A|Agilent Technologies|
|DC resistance||4338A|Agilent Technologies|
||Insulation resistance|4339A|Agilent Technologies|



- ＊ Equivalent measurement equipment may be used. 

## **IMPEDANCE VS. FREQUENCY CHARACTERISTICS** 

**==> picture [494 x 274] intentionally omitted <==**

**----- Start of picture text -----**<br>
10000<br>S SS SS<br>ec<br>— eee<br>1000 a<br>901 Common mode<br>121 Common mode<br>900 Differential mode<br>361 Common mode 121  Differential mode<br>100<br>901 Differential mode<br>ae ae<br>361 Differential mode<br>Sastre SS a<br>900 Common mode<br>10<br>oe— et<br>1<br>1 Parr 10 Trrt 100 Pr eetih 1000<br>Frequency (MHz)<br>○ Measurement equipment<br>Product No. Manufacturer<br>4991A Agilent Technologies<br>＊ Equivalent measurement equipment may be used.<br>)Ω<br>Impedance (<br>**----- End of picture text -----**<br>


• All specifications are subject to change without notice. 

001-01 / 20131101 / e9719_acm2012.fm 

(7/7) 

## **E M C C o m p o n e n t s** ee ———— ACM series 

## **Packaging style** 

## **REEL DIMENSIONS** 

**==> picture [180 x 200] intentionally omitted <==**

**----- Start of picture text -----**<br>
2.0±0.5 E<br>1.0<br>I ø13.0 P ±0.2 W1<br>ø21.0±0.8 W2<br>= im<br>A<br>Dimensions in mm<br>N<br>**----- End of picture text -----**<br>


|Type|A|W1|W2|N|E|
|---|---|---|---|---|---|
|**ACM2012**|ø330±2|9.5±0.5|13.5±1|100±1|2 typ.|
||ø180±3|9+1/–0|13±1|60+1/–0|2 typ.|



## **TAPE DIMENSIONS** 

**==> picture [509 x 234] intentionally omitted <==**

**----- Start of picture text -----**<br>
P2 P0 t<br>S øD0 eo |<br>aaa A | P1 K<br>Dimensions in mm<br>Type A B øD0 E F P0 P1 P2 W K t<br>eee ACM2012 1.4±0.1 2.25±0.1 1.5+0.1/0 1.75±0.1 3.5±0.1 4.0±0.1 4.0±0.1 2.0±0.1 8.0±0.2 1.4±0.1 ee 0.25±0.05<br>500 to 560min.<br>160min. Taping 440min.<br>OO008 8 0 TT]0<br>Drawing direction Dimensions in mm<br>E<br>F W<br>B<br>**----- End of picture text -----**<br>


• All specifications are subject to change without notice. 

001-01 / 20131101 / e9719_acm2012.fm