ACH3218-220-TD01

July 2013 

## 3-terminal Filters 

For power line 

## ACH series 

**ACH32C [1206 inch]* ACH3218 [1207 inch]** 

- Dimensions Code JIS[EIA] 

(2/9) 

## **REMINDERS FOR USING THESE PRODUCTS** 

Before using these products, be sure to request the delivery specifications. 

## **SAFETY REMINDERS** 

Please pay sufficient attention to the warnings for safe designing when using these products. 

## **REMINDERS** 

- ~~O~~ The storage period is less than 12 months.  Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. 

~~O~~ Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). 

- ~~O~~ Before soldering, be sure to preheat components. 

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. 

- ~~O~~ Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. 

- ~~O~~ When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. 

- O Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. 

- ~~O~~ Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. 

~~O~~ Use a wrist band to discharge static electricity in your body through the grounding wire. 

~~O~~ Do not expose the products to magnets or magnetic fields. 

~~O~~ Do not use for a purpose outside of the contents regulated in the delivery specifications. 

- ~~O~~ The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. 

   - The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. 

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. 

- (1) Aerospace/Aviation equipment (8) Public information-processing equipment 

- (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment 

(3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications 

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 

001-01 / 20130722 / e9611_ach.fm 

(3/9) 

## **E M C C o m p o n e n t s** —————————rl—l™L **3-terminal Filters Product compatible with RoHS directive** 

**Product compatible with RoHS directive Halogen-free Compatible with lead-free solders** 

## **For power line** 

## **Overview of the ACH Series** 

## **FEATURES** 

T-type EMC filter that can be used for high-current circuits. 

Achieve excellent attenuation characteristics by using it for circuits with stable grounds. 

Does not require mounting space due to vertical mounting design, making it perfect for high-density circuits. Guaranteed temperature range is –40 to +125°C, so it can be used under severe environmental conditions. Use this product under reflow soldering conditions. 

## **APPLICATION** 

HE devices (TVs, VTRs, CD players, electronic musical instruments, PCs, etc.) OA equipment (Computers, terminals, facsimiles, etc.) 

FA equipment (Robots, NC machine tools, process controllers, etc.) 

AE equipment (Car navigation systems, ECUs, etc.)  ACH32C cannot be used for ECUs. 

## **PART NUMBER CONSTRUCTION** 

## **ACH32C** 

**==> picture [429 x 164] intentionally omitted <==**

**----- Start of picture text -----**<br>
- -<br>ACH 32C 103 T 001<br>et<br>L×W×T Dimensions Capacitance<br>Series name Packaging style Internal code<br>(mm) (pF)<br>32C 3.2×1.6×2.1 100      10 T Taping<br>es ee 103 10000<br>ACH3218<br>- -<br>ACH 3218 223 T □□□<br>a<br>L×W×T Dimensions Capacitance<br>Series name Packaging style Internal code<br>(mm) (pF)<br>a 3218 3.2×1.8×2.5 223 22000 T Taping<br>**----- End of picture text -----**<br>


## **ACH3218** 

## **OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT** 

|**Type**|**Temperature range**|**Temperature range**|**Package quantity**|**Individual weight**|
|---|---|---|---|---|
||**Operating**<br>**temperature**|**Storage**<br>**temperature**|||
||（**°C**）|（**°C**）|（**pieces/reel**）|（**mg**）|
|**ACH32C**|–40 to +125|–40 to +125|2,000|70|
|**ACH3218**|–40 to +125|–40 to +125|1,000|70|



The Storage temperature range is for after the circuit board is mounted. 

RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. 

• All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm 

(4/9) 

## **Overview of the ACH Series** 

## **RECOMMENDED REFLOW PROFILE** 

||||Preheating|Preheating||Soldering<br>T4<br>Peak|Soldering<br>T4<br>Peak|Soldering<br>T4<br>Peak|Soldering<br>T4<br>Peak|Natural<br>cooling|||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|T:Temperature|T1|||T2|T3||t3|||T3|||
|||||t1|||t2||||||
||||||||||||||
|||||t:Time|||||||||
|**Preheating**|||||**Soldering**||||||**Peak**||
|**Temp.**|||**Time**||**Temp.**|||**Time**|||**Temp.**|**Time**|
|**T1**|**T2**||**t1**||**T3**|||**t2**|||**T4**|**t3**|
|150°C<br>180°C|||60 to 120s|60 to 120s|230°C||30 to 60s||||250 to 260°C|10s max.|



• All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm 

(5/9) 

**E M C C o m p o n e n t s** ————rt—“‘“—— 

## ACH series 

## **ACH32C Type** 

## **SHAPE & DIMENSIONS** 

**==> picture [259 x 152] intentionally omitted <==**

**----- Start of picture text -----**<br>
3.2±0.2<br>1 3<br>aio<br>2<br>Dimensions in mm<br>0.2<br>±<br>1.6<br>0.2<br>±<br>2.1<br>0.1<br>**----- End of picture text -----**<br>


## **RECOMMENDED LAND PATTERN** 

**CIRCUIT DIAGRAM** 

**==> picture [344 x 106] intentionally omitted <==**

**----- Start of picture text -----**<br>
4.2<br>1.0 0.6 1.0<br>1 3<br>GND<br>2<br>[|<br>• No polarity<br>fa[L]l ,_ : Dimensions in mm [= =|<br>2.6 0.5<br>**----- End of picture text -----**<br>


• All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm 

(6/9) 

## **E M C C o m p o n e n t s** _SSSSSSSStrt—‘“__ ACH series **ACH32C Type** 

## **ELECTRICAL CHARACTERISTICS** 

## **CHARACTERISTICS SPECIFICATION TABLE** 

||**Rated voltage**<br>**(V)max.**|**Rated current**<br>**(A)max.**|**Rated current**<br>**(A)max.**|**Insulation resistance**<br>**(M**<br>**)min.**|**Insulation resistance**<br>**(M**<br>**)min.**|**DC resistance**<br>**(m**|**DC resistance**<br>**)max.**|**Guaranteed**<br>**insertion loss**<br>**(dB)**|**Guaranteed frequency**<br>**bandwidth**<br>**(MHz)**|**Guaranteed frequency**<br>**Part No.**|
|---|---|---|---|---|---|---|---|---|---|---|
|50||6||100||2||–15|2000 to 6000|ACH32C-100-T001|
||50|6||100||2||–15|1300 to 2500|ACH32C-220-T001|
|50||6||100||2||–15|650 to 2500|ACH32C-470-T001|
||50|6||100||2||–20|450 to 1300|ACH32C-101-T001|
|50||6||100||2||–20|200 to 800|ACH32C-331-T001|
||50|6||100||2||–25|100 to 350|ACH32C-102-T001|
|50||6||100||2||–25|55 to 300|ACH32C-222-T001|
||50|6||100||2||–25|30 to 200|ACH32C-103-T001|
|50||6||100||2||–25|10 to 300|ACH32C-333-T001|
||50|6||100||2||–25|3.5 to 200|ACH32C-104-T001|
||○Measurement equipment|Measurement equipment|||||||||
||Measurement item|Measurement item|Product No.|||Manufacturer|||||
||Insertion loss||E5071B|||Agilent Technologies|||||
||DC resistance|DC resistance|4338A|||Agilent Technologies|||||
||Insulation resistance||4339A|||Agilent Technologies|||||



- ＊ Equivalent measurement equipment may be used. 

## **INSERTION LOSS VS. FREQUENCY CHARACTERISTICS** 

**==> picture [492 x 275] intentionally omitted <==**

**----- Start of picture text -----**<br>
0<br>10<br>20<br>30 220 100<br>470<br>40 101<br>331<br>50<br>102<br>104<br>103 222<br>60<br>333<br>70<br>80 Riven nneecumet<br>1 | LT 10 FPP 100 ET 1000 10000<br>Frequency (MHz)<br>○ Measurement equipment<br>Product No. Manufacturer<br>E5071B Agilent Technologies<br>＊ Equivalent measurement equipment may be used.<br>Insertion loss (dB)<br>**----- End of picture text -----**<br>


• All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm 

(7/9) 

## ACH series 

## **ACH3218 Type** 

## **SHAPE & DIMENSIONS** 

**==> picture [109 x 150] intentionally omitted <==**

**----- Start of picture text -----**<br>
3.2±0.3<br>0.6 0.45<br>2.5±0.25<br>1.8±0.2<br>**----- End of picture text -----**<br>


**==> picture [59 x 6] intentionally omitted <==**

**----- Start of picture text -----**<br>
Dimensions in mm<br>**----- End of picture text -----**<br>


**RECOMMENDED LAND PATTERN** 

## **CIRCUIT DIAGRAM** 

**==> picture [330 x 143] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 3<br>GND<br>2<br>• No polarity<br>a o<br>0.6<br>1.4 2.2 1.4 Dimensions in mm<br>1.94<br>**----- End of picture text -----**<br>


• All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm 

(8/9) 

## **E M C C o m p o n e n t s** eee ACH series **ACH3218 Type** 

## **ELECTRICAL CHARACTERISTICS** 

## **CHARACTERISTICS SPECIFICATION TABLE** 

|**Insertion loss 25dB**<br>**frequency range**<br>**(MHz)**|**Insertion loss 25dB**<br>**frequency range**<br>**(MHz)**|**Rated voltage**<br>**(V)max.**|**Rated voltage**<br>**(V)max.**|**Rated voltage**<br>**(V)max.**|**Rated voltage**<br>**(V)max.**||**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Rated current**<br>**(A)max.**<br>**DC resistance**<br>**(**<br>**)max.**<br>**[Terminal No.1 to 3**|**Terminal No.1 to 3]**|**Terminal No.1 to 3]**||**Insulation resistance**<br>**(M**<br>**)min.**<br>**[Terminal No.1 to 2/No.2 to 3]**<br>**Part No.**|**Insulation resistance**<br>**(M**<br>**)min.**<br>**[Terminal No.1 to 2/No.2 to 3]**<br>**Part No.**|**Insulation resistance**<br>**(M**<br>**)min.**<br>**[Terminal No.1 to 2/No.2 to 3]**<br>**Part No.**|**Insulation resistance**<br>**(M**<br>**)min.**<br>**[Terminal No.1 to 2/No.2 to 3]**<br>**Part No.**|||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|11 to 55||20||||||1.5||||0.06||||||1000|||ACH3218-223-T□□□|||
|17 to 60||20|||||1.5|||||0.06||||||1000|||ACH3218-103-T□□□|||
|22 to 75||20||||||1.5||||0.06||||||1000|||ACH3218-682-T□□□|||
|30 to 85||20|||||1.5|||||0.06||||||1000|||ACH3218-472-T□□□|||
|37 to 90||20||||||1.5||||0.06||||||1000|||ACH3218-332-T□□□|||
|45 to 105||20|||||1.5|||||0.06||||||1000|||ACH3218-222-T□□□|||
|60 to 115||20|||||1.5|||||0.06||||||1000|||ACH3218-152-T□□□|||
|80 to 140||20|||||1.5|||||0.06||||||1000|||ACH3218-102-T□□□|||
|95 to 150||20|||||1.5|||||0.06||||||1000|||ACH3218-681-T□□□|||
|120 to 180||20|||||1.5|||||0.06||||||1000|||ACH3218-471-T□□□|||
|130 to 210||20|||||1.5|||||0.06||||||1000|||ACH3218-331-T□□□|||
|170 to 250||20|||||1.5|||||0.06||||||1000|||ACH3218-221-T□□□|||
|205 to 280||20|||||1.5|||||0.06||||||1000|||ACH3218-151-T□□□|||
|265 to 340||20|||||1.5|||||0.06||||||1000|||ACH3218-101-T□□□|||
|340 to 420||20|||||1.5|||||0.06||||||1000|||ACH3218-680-T□□□|||
|420 to 500||20|||||1.5|||||0.06||||||1000|||ACH3218-470-T□□□|||
|500 to 600||20|||||1.5|||||0.06||||||1000|||ACH3218-330-T□□□|||
|600 to 700||20|||||1.5|||||0.06||||||1000|||ACH3218-220-T□□□|||
|**INSERTION LOSS VS. FREQUENCY CHARACTERISTICS**|||||||**INSERTION LOSS VS. FREQUENCY CHARACTERISTICS**|||||||||||||||||
|50<br>40<br>30<br>20<br>10<br>0<br>Insertion loss (dB)||||||||||||223<br>103<br>472<br>682<br>332<br>222<br>152<br>102<br>CS<A"|||||||331<br>471<br>681<br>221151 101<br>680<br>470<br>330 220|||||
|1||3||||||||10<br>30||||||||100||1000<br>300||||
|||||||||||||Frequency (MHz)||||||||||||



• All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm 

(9/9) 

## **E M C C o m p o n e n t s** —<———— 

## ACH series 

## **Packaging style** 

## **REEL DIMENSIONS** 

**==> picture [451 x 578] intentionally omitted <==**

**----- Start of picture text -----**<br>
2.0±0.5<br>Type W1 W2<br>ACH32C 9±0.3 13+1.4<br>ACH3218 13.0±0.3 17.0±0.4<br>a= —<br>1.0<br>ø13±0.2 W1<br>ø21±0.8 W2<br>|] 4<br>ø180 [+0] –3<br>Dimensions in mm<br>TAPE DIMENSIONS<br>o 1.5 [+0.1] 0 2.0±0.05 e 4.0±0.1<br>A 4.0±0.1 K<br>areval<br>Dimensions in mm<br>Type A B F W K<br>ACH32C 1.9±0.1 3.5±0.1 3.5±0.05 8.0±0.2 2.3±0.1<br>ACH3218 2.2±0.1 3.7±0.05 5.5±0.05 12.0±0.3 3.15max.<br>—<br>500 to 560min.<br>160min. Taping 440min.<br>ACH32C TYPE<br>Drawing direction Dimensions in mm<br>40 to 80 Taping 200min.<br>ACH3218 TYPE<br>Drawing direction 300min. Dimensions in mm<br>ø60min.<br>1.75±0.1<br>F<br>B 8.0±0.3<br>**----- End of picture text -----**<br>


- All specifications are subject to change without notice. 

001-01 / 20130722 / e9611_ach.fm