6AG1155-5BA00-2AB0

**6AG1155-5BA00-2AB0** 

**Data sheet** 

SIPLUS ET 200MP IM155-5 DP ST based on 6ES7155-5BA00-0AB0 with conformal coating, -40…+60 °C, start up -25 °C, PROFIBUS connection for max. 12 S7-1500 modules 

|**General information**||
|---|---|
|Product type designation|IM 155-5 DP ST|
|Firmware version||
|● FW updatepossible|Yes|
|Vendor identification(VendorID)|81AAh|
|based on|6ES7155-5BA00-0AB0|
|Product function||
|● I&M data|Yes; I&M0 to I&M3|
|● Module swappingduringoperation(hot swapping)|No|
|● Isochronous mode|No|
|● IRT|No|
|● Tool changer|No|
|● Local coupling, IO data|No|
|Engineeringwith||
|● STEP 7 TIA Portal configurable/integrated from version|see entryID: 109746275|
|**Configuration control**||
|via dataset|No|
|**Supply voltage**||
|Rated value(DC)|24 V|
|permissible range, lower limit(DC)|19.2 V|
|permissible range, upper limit(DC)|28.8 V|
|Reversepolarity protection|Yes|
|Short-circuitprotection|Yes|
|Mains buffering||
|● Mains/voltage failure stored energytime|5 ms|
|**Input current**||
|Current consumption(rated value)|0.2 A; at 24 V DC and without load|
|Current consumption, max.|1.2 A; at 20.4 V DC and max. load|
|Inrush current, max.|4 A|
|I²t|0.09 A²·s|
|from interface 5 V DC, max.|80 mA|
|**Power**||
|Infeed power to the backplane bus|14 W|
|**Power loss**||
|Power loss, typ.|4 W|
|**Address area**||
|Address spaceper module||
|● Address space per module, max.|64 byte; For input and output data respectively|



6AG11555BA002AB0 Page 1/4 

Subject to change without notice © Copyright Siemens 

5/21/2026 

||Address spaceper station|Address spaceper station||
|---|---|---|---|
||● Address space per station, max.|244 byte; For input and output data respectively||
||**Hardware configuration**|||
||Integratedpower supply|Yes; 14 W||
||Systempower supplycan beplugged in to left of IM|No||
||Number ofpermissiblepower segments|1; incl. interface module||
||Rack|||
||● Modules per rack, max.|12; I/O modules||
||**Interfaces**|||
||Number of PROFIBUS interfaces|1; 1 port||
||**1. Interface**|||
||Interface types|||
||● RS 485|Yes||
||● Number ofports|1||
||● integrated switch|No||
||● BusAdapter(PROFINET)|No||
||Protocols|||
||● PROFIBUS DP device|Yes||
||PROFINET IO Device|||
||Services|||
||— IRT|No||
||**Interface types**|||
||RS 485|||
||● Transmission rate, max.|12 Mbit/s||
||**Protocols**|||
||Supportsprotocol for PROFINET IO|No||
||PROFIsafe|Yes||
||PROFIBUS|Yes||
||EtherNet/IP|No||
||Modbus TCP|No||
||PROFIBUS DP|||
||Services|||
||— SYNC capability|Yes||
||— FREEZE capability|Yes||
||— DPV1|Yes||
||**Interrupts/diagnostics/status information**|||
||Status indicator|Yes||
||Alarms|Yes||
||Diagnostics function|Yes||
||Diagnostics indication LED|||
||● RUN LED|Yes;green LED||
||● ERROR LED|Yes; red LED||
||● MAINT LED|Yes; Yellow LED||
||● Connection displayDP|Yes;green LED||
||**Potential separation**|||
||between backplane bus and electronics|No||
||between PROFIBUS DP and all other circuit components|Yes||
||between supplyand all other circuits|No||
||**Permissible potential difference**|||
||between different circuits|Safetyextra low voltage SELV||
||**Isolation**|||
||Isolation tested with|707 V DC(type test)||
||**Standards, approvals, certificates**|||
||Ecological footprint|||
||● environmentalproduct declaration|Yes||
||Global warming potential|||
||—global warming potential,(total) [CO2 eq]|64.1 kg||
||— global warming potential, (during production) [CO2<br>eq]|11.1 kg||



6AG11555BA002AB0 Page 2/4 

Subject to change without notice © Copyright Siemens 

5/21/2026 

|— global warming potential, (during operation) [CO2<br>eq]|53.6 kg|53.6 kg|53.6 kg|
|---|---|---|---|
|— global warming potential, (after end of life cycle)<br>[CO2 eq]|-0.669 kg|||
|**Ambient conditions**||||
|Ambient temperature duringoperation||||
|● horizontal installation, min.|-40 °C; = Tmin(incl. condensation/frost); start-up @-25 °C|||
|● horizontal installation, max.|60 °C; = Tmax|||
|Altitude duringoperation relatingto sea level||||
|● Installation altitude above sea level, max.|5 000 m|||
|● Ambient air temperature-barometric pressure-altitude|Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... (Tmax<br>- 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500 m) // Tmin ... (Tmax -20 K)<br>at 658 hPa ... 540 hPa(+3 500 m ... +5 000 m)|||
|Relative humidity||||
|● With condensation, tested in accordance with IEC 60068-<br>2-38, max.|100 %; RH incl. condensation / frost (no commissioning in bedewed state),<br>horizontal installation|||
|Resistance||||
|Coolants and lubricants||||
|— Resistant to commercially available coolants and<br>lubricants|Yes; Incl. diesel and oil droplets in the air|||
|Use in stationaryindustrial systems||||
|— to biologically active substances according to EN<br>60721-3-3|Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna);<br>Class 3B3 on request|||
|— to chemically active substances according to EN<br>60721-3-3|Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52<br>(degree of severity 3). The supplied connector covers must remain on the<br>unused interfaces duringoperation!|||
|— to mechanically active substances according to EN<br>60721-3-3|Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on<br>the unused interfaces duringoperation!|||
|Use on ships/at sea||||
|— to biologically active substances according to EN<br>60721-3-6|Yes; Class 6B2 mold and fungal spores (excluding fauna); Class 6B3 on<br>request|||
|— to chemically active substances according to EN<br>60721-3-6|Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity<br>degree 3); *|||
|— to mechanically active substances according to EN<br>60721-3-6|Yes; Class 6S3 incl. sand, dust; *|||
|Usage in industrialprocess technology||||
|— Against chemically active substances acc. to EN<br>60654-4|Yes; Class 3 (excluding trichlorethylene)|||
|— Environmental conditions for process, measuring<br>and control systems acc. to ANSI/ISA-71.04|Yes; Level GX group A/B (excluding trichlorethylene; harmful gas<br>concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level<br>LC3(salt spray)and level LB3(oil)|||
|Remark||||
|— Note regarding classification of environmental<br>conditions acc. to EN 60721, EN 60654-4 and<br>ANSI/ISA-71.04|* The supplied plug covers must remain in place over the unused interfaces<br>during operation!|||
|Conformal coating||||
|● Coatings for printed circuit board assemblies acc. to EN<br>61086|Yes; Class 2 for high reliability|||
|● Protection against foulingacc. to EN 60664-3|Yes; Type 1protection|||
|● Militarytestingaccordingto MIL-I-46058C, Amendment 7|Yes; Discoloration of coating possible duringservice life|||
|● Qualification and Performance of Electrical Insulating<br>Compound for Printed Board Assemblies according to IPC-<br>CC-830A|Yes; Conformal coating, Class A|||
|**Connection method**||||
|ET-Connection||||
|● via BU/BA Send|No|||
|**Dimensions**||||
|Width|35 mm|||
|Height|147 mm|||
|Depth|129 mm|||
|**Weights**||||
|Weight, approx.|360g|||
|**Classifications**||||
|||**Version**|**Classification**|



6AG11555BA002AB0 Page 3/4 

Subject to change without notice © Copyright Siemens 

5/21/2026 

eClass 14 27-24-26-08 eClass 12 27-24-26-08 eClass 9.1 27-24-26-08 eClass 9 27-24-26-08 eClass 8 27-24-26-08 eClass 7.1 27-24-26-08 eClass 6 27-24-26-08 ETIM 10 EC001604 ETIM 9 EC001604 ETIM 8 EC001604 ETIM 7 EC001604 IDEA 4 3564 UNSPSC 15 32-15-17-05 ~~ee~~ **Approvals / Certificates General Product Approval** Manufacturer DeclaraChina RoHS tion ~~co~~ ep—i ~~C<~~ Se **General Product Approval EMV For use in hazardous locations** ~~—~~ China RoHS € && © **For use in hazardous locations Maritime application Environment** CCC-Ex © € © & **last modified:** 10/23/2025 

6AG11555BA002AB0 Page 4/4 

Subject to change without notice © Copyright Siemens 

5/21/2026