6AG1010-1AU00-4AA0

**6AG1010-1AU00-4AA0** 

**Data sheet** 

SIPLUS SIMOCODE pro V basic unit 2 based on 3UF7010-1AU00-0 with conformal coating, -25…+60 °C, PROFIBUS DP interface 12 Mbps, RS-485; 4 I/3 O freely parameterizable US: 110-240 V AC/DC; input for thermistor connection; monostable relay outputs; expandable by expansion modules 

|**product brand name**|SIRIUS|
|---|---|
|**product designation**|Motor management system|
|**design of theproduct**|basic unit 2|
|**product type designation**|SIMOCODE pro V PB|
|**General technical data**||
|**certificate of suitability**|CE / RoHS|
|**product function**||
|● current measurement|No|
|● voltage measurement|No|
|● activepower measurement|Yes|
|● energymeasurement|No|
|● frequencymeasurement|No|
|● bus communication|Yes|
|● data acquisition function|Yes|
|● diagnostics function|Yes|
|●passwordprotection|Yes|
|● test function|Yes|
|● maintenance function|Yes|
|● MRRT redundancy procedure|No|
|**product component**||
|● input for thermistor connection|Yes|
|● digital input|Yes|
|● input for analogtemperature sensors|No|
|● input forground fault detection|No|
|● relayoutput|Yes|
|**product extension**||
|● temperature monitoringmodule|Yes|
|● current measuringmodule|Yes|
|● current/voltage measuringmodule|Yes|
|● fail-safe digital I/O module|Yes|
|●ground-fault monitoringmodule|Yes|
|● decouplingmodule|Yes|
|● analogI/O module|Yes|
|● digital I/O module with monostable outputs|Yes|
|● digital I/O module with bistable outputs|Yes|
|● control unit with display|Yes|
|● control unit|Yes|
|**apparent power consumption**|8.3 VA|



6AG10101AU004AA0 Page 1/6 

Subject to change without notice © Copyright Siemens 

5/10/2026 

|**consumed activepower**|3.6 W|
|---|---|
|insulation voltage with degree ofpollution 3 at AC rated value|300 V|
|**surge voltage resistance rated value**|4 000 V|
|**shock resistance**||
|**● according to IEC 60068-2-27**|15g/ 11 ms|
|||
|**● vibration resistance**|1 … 6 Hz / 15 mm; 6 … 500 Hz / 2g|
|**switching capacity current of the NO contacts of the relay**<br>**outputs at AC-15**||
|● at 24 V|6 A|
|● at 120 V|6 A|
|● at 230 V|3 A|
|**switching capacity current of the NO contacts of the relay**<br>**outputs at DC-13**||
|● at 24 V|2 A|
|● at 60 V|0.55 A|
|● at 125 V|0.25 A|
|**mechanical service life(operating cycles) typical**|10 000 000|
|electrical endurance(operatingcycles)typical|100 000|
|**buffering time in the event ofpower failure**|0 s|
|**reference code according to IEC 81346-2**|F|
|continuous current of the NO contacts of the relayoutputs||
|● at 50 °C|6 A|
|● at 60 °C|5 A|
|**type of input characteristic**|Type 1 in accordance with EN 61131-2|
|**Substance Prohibitance(Date)**|09/13/2024|
|**SVHC substance name**|Lead CAS-No. 7439-92-1|
|**Net Weight**|0.369 kg|
|**Electromagnetic compatibility**||
|EMC emitted interference accordingto IEC 60947-1|class A|
|EMC immunityaccordingto IEC 60947-1|corresponds to degree of severity3|
|**conducted interference**||
|● due to burst accordingto IEC 61000-4-4|2 kV(powerports)/ 1 kV(signalports)|
|● due to conductor-earth surge accordingto IEC 61000-4-5|2 kV|
|● due to conductor-conductor surge according to IEC<br>61000-4-5|1 kV|
|● due to high-frequency radiation according to IEC 61000-<br>4-6|10 V|
|**field-based interference according to IEC 61000-4-3**|10 V/m|
|**electrostatic discharge according to IEC 61000-4-2**|6 kV contact discharge / 8 kV air discharge|
|**conducted HF interference emissions according to**<br>**CISPR11**|corresponds to degree of severity A|
|**field-bound HF interference emission according to CISPR11**|corresponds to degree of severityA|
|**Inputs/ Outputs**||
|**product function**||
|●parameterizable inputs|Yes|
|●parameterizable outputs|Yes|
|**number of inputs**|4|
|● for thermistor connection|1|
|number of digital inputs with a common referencepotential|4|
|**digital input version**||
|● type 1 acc. to IEC 61131|Yes|
|**input voltage at digital input at DC**||
|● rated value|24 V|
|**number of outputs**|3|
|**number of semiconductor outputs**|0|
|**number of outputs as contact-affected switching element**|3|
|**switching behavior**|monostable|
|**number of relay outputs**|3|
|**type of relay outputs**|Monostable|



6AG10101AU004AA0 Page 2/6 

Subject to change without notice © Copyright Siemens 

5/10/2026 

||**wire length for digital signals maximum**|300 m||
|---|---|---|---|
||**wire length for thermistor connection**|||
||● with conductor cross-section = 0.5 mm² maximum|50 m||
||● with conductor cross-section = 1.5 mm² maximum|150 m||
||● with conductor cross-section = 2.5 mm² maximum|250 m||
||**Protective and monitoring functions**|||
||**product function**|||
||● asymmetrydetection|Yes||
||● blockingcurrent evaluation|Yes||
||●power factor monitoring|Yes||
||●ground fault detection|Yes||
||●ground-fault monitoring|No||
||●phase failure detection|Yes||
||●phase sequence recognition|Yes||
||● voltage detection|Yes||
||● monitoringof number of start operations|Yes||
||● overvoltage detection|Yes||
||● overcurrent detection 1phase|Yes||
||● undervoltage detection|Yes||
||● undercurrent detection 1phase|Yes||
||● activepower monitoring|Yes||
||**product function**|||
||● current detection|Yes||
||● overloadprotection|Yes||
||● evaluation of thermistor motorprotection|Yes||
||**total cold resistance number of sensors in series maximum**|1.5 kΩ||
||**response value of thermoresistor**|3 400 ... 3 800 Ω||
||● of the short-circuit control|9 Ω||
||**release value of thermoresistor**|1 500 ... 1 650 Ω||
||**Motor control functions**|||
||**product function**|||
||●parameterizable overload relay|Yes||
||● circuit breaker control|Yes||
||● direct start|Yes||
||● reverse starting|Yes||
||● star-delta circuit|Yes||
||● star-delta reversingcircuit|Yes||
||● Dahlander circuit|Yes||
||● Dahlander reversingcircuit|Yes||
||●pole-changingswitch circuit|Yes||
||●pole-changingswitch reversingcircuit|Yes||
||● slide control|Yes||
||● valve control|Yes||
||**Communication/ Protocol**|||
||**protocol is supported**|||
||● PROFIBUS DPprotocol|Yes||
||● PROFINET IOprotocol|No||
||● PROFIsafeprotocol|Yes||
||● Modbus RTU|No||
||● EtherNet/IP|No||
||● OPC UA Server|No||
||● LLDP|No||
||● Address Resolution Protocol(ARP)|No||
||● SNMP|No||
||● HTTPS|No||
||● NTP|No||
||● Media RedundancyProtocol(MRP)|No||
||**product function**|||
||● web server|No||



6AG10101AU004AA0 Page 3/6 

Subject to change without notice © Copyright Siemens 

5/10/2026 

|● shared device|No|
|---|---|
|● at the Ethernet interface Autocrossover|No|
|● at the Ethernet interface Autonegotiation|No|
|● at the Ethernet interface Autosensing|No|
|● is supported Device Level Ring (DLR)|No|
|● is supported PROFINET system redundancy (S2)|No|
|● supports PROFIenergymeasured values|No|
|● supports PROFIenergyshutdown|No|
|**transfer rate maximum**|12 Mbit/s|
|**identification & maintenance function**||
|● I&M0 - device-specific information|Yes|
|● I&M1 - higher level designation/location designation|Yes|
|● I&M2 - installation date|Yes|
|● I&M3 - comment|Yes|
|type of electrical connection of the communication interface|9-pin SUB-D socket(12 Mbit)/ screw terminal(1.5 Mbit)|
|**Installation/ mounting/ dimensions**||
|**mounting position**|any|
|**fastening method**|screw and snap-on mounting|
|**height**|111 mm|
|**width**|45 mm|
|**depth**|124 mm|
|**required spacing**||
|● top|40 mm|
|● bottom|40 mm|
|● left|0 mm|
|● right|0 mm|
|**Connections/ Terminals**||
|**product component removable terminal for auxiliary and**<br>**control circuit**|Yes|
|**type of electrical connection**||
|● for auxiliaryand control circuit|screw-type terminals|
|**type of connectable conductor cross-sections**||
|● solid|1x(0.5 ... 4.0mm²), 2x(0.5 ... 2.5 mm²)|
|● finelystranded with core endprocessing|1x(0.5 ... 2.5 mm²), 2x(0.5 ... 1.5 mm²)|
|● for AWG cables solid|1x(20 ... 12), 2x(20 ... 14)|
|● for AWG cables stranded|1x(20 ... 14), 2x(20 ... 16)|
|tighteningtorque with screw-type terminals|0.8 ... 1.2 N·m|
|tighteningtorque[lbf·in]with screw-type terminals|7 ... 10.3 lbf·in|
|**type of connectable conductor cross-sections for**<br>**PROFIBUS wire**|2x 0.34 mm², AWG 22|
|**Ambient conditions**||
|installation altitude at height above sea level maximum|2 000 m|
|**ambient temperature**||
|● duringoperation|-25 ... +60 °C|
|● duringstorage|-40 ... +80 °C|
|● duringtransport|-40 ... +80 °C|
|**environmental category**||
|● during operation according to IEC 60721|3K6 (no formation of ice, no condensation, relative humidity 10 ... 95%), 3C3<br>(no salt mist), 3S2(sand must notget into the devices), 3M6|
|● during storage according to IEC 60721|1K6 (no condensation, relative humidity 10 ... 95%), 1C2 (no salt mist), 1S2<br>(sand must notget into the devices), 1M4|
|● duringtransport accordingto IEC 60721|2K2, 2C1, 2S1, 2M2|
|**relative humidity**||
|● duringoperation|5 ... 95 %|
|**contact rating of auxiliary contacts according to UL**|B300 / R300|
|**Short-circuit protection**||
|design of short-circuit protection per output|Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-<br>breaker C char.: 1.6 A(IEC 60947-5-1)or 6 A(I_K < 500 A)|
|Electrical Safety||
|**touch protection against electrical shock**|finger-safe|



6AG10101AU004AA0 Page 4/6 

Subject to change without notice © Copyright Siemens 

5/10/2026 

|**Galvanic isolation**<br>~~|~~|**Galvanic isolation**<br>~~|~~|
|---|---|
|**(electrically) protective separation according to IEC 60947-1**<br>~~|~~|All circuits with protective separation (double creepage paths and clearances),<br>the information in the "Protective Separation" test report, No. A0258, must be<br>observed(link see further information)<br>~~|~~|
|**design of the electrical isolation**|Protective separation in accordance with IEC 60947-1 for all circuits|
|● note|Test report No. A0258 must be observed<br>(https://support.industry.siemens.com/cs/document/109748152)|
|**Control circuit/ Control**<br>~~|~~||
|**product function soft starter control**<br>~~|~~|Yes<br>~~|~~|
|**type of voltage of the control supply voltage**|AC/DC|
|**control supply voltage at AC**||
|● at 50 Hz rated value|110 ... 240 V|
|● at 60 Hz rated value|110 ... 240 V|
|**control supply voltage frequency**||
|**● 1 rated value**|50 Hz|
|**● 2 rated value**|60 Hz|
|**relative symmetrical tolerance of the control supply voltage**<br>**frequency**|5 %|
|**control supply voltage at DC rated value**|110 ... 240 V|
|**operating range factor control supply voltage rated value at**<br>**DC**||
|● initial value|0.85|
|● full-scale value|1.1|
|**operating range factor control supply voltage rated value at**<br>**AC at 50 Hz**||
|● initial value|0.85|
|● full-scale value|1.1|
|**operating range factor control supply voltage rated value at**<br>**AC at 60 Hz**||
|● initial value|0.85|
|● full-scale value|1.1|
|**inrush currentpeak**||
|● at 240 V|15 A|
|**duration of inrush currentpeak**||
|● at 240 V|1 ms|
|**Approvals Certificates**<br>~~|~~||
|**General Product Approval**<br>~~|~~||



~~|~~ **Approvals Certificates** 

**General Product Approval** 

~~—~~ China RoHS Manufacturer Declaration - China RoHS CE ~~RC~~ 

**General Product ApEMV proval** 

~~OO—CsSCSC—“CCSC(C‘(SCds~~ **Further information Information on the packaging** https://support.industry.siemens.com/cs/ww/en/view/109813875 **Information for data generation and storage** https://support.industry.siemens.com/cs/ww/en/view/109995012 

**Information- and Downloadcenter (Catalogs, Brochures,…)** https://www.siemens.com/ic10 

**Industry Mall (Online ordering system)** https://mall.industry.siemens.com/mall/en/en/Catalog/product?mlfb=6AG1010-1AU00-4AA0 **Cax online generator** https://support.automation.siemens.com/WW/CAXorder/default.aspx?lang=en&mlfb=6AG1010-1AU00-4AA0 **Service&Support (Manuals, Certificates, Characteristics, FAQs,...)** https://support.industry.siemens.com/cs/ww/en/ps/6AG1010-1AU00-4AA0 

6AG10101AU004AA0 Page 5/6 

Subject to change without notice © Copyright Siemens 

5/10/2026 

**Image database (product images, 2D dimension drawings, 3D models, device circuit diagrams, EPLAN macros, ...)** https://www.automation.siemens.com/bilddb/cax_de.aspx?mlfb=6AG1010-1AU00-4AA0&lang=en 

**==> picture [419 x 238] intentionally omitted <==**

**----- Start of picture text -----**<br>
-F | a<br>SIEMENS<br>|<br>|<br>DEVICE Logic<br>BUS<br>GEN. FAULT SIMOCODE PRO<br>| PROFIBUS DP<br>|<br>| L<br>| 7 3 PROFIBUS DP<br>St<br>ee<br>f f ee ee [| |<br>A1 9 10 4 5 8 1 6<br>IN1 IN2 IN3 IN4 24V OUT1/2 OUT3<br>PE OUT1 OUT2 OUT3<br>A2 SPE T1 T2 2 3 7 A B DP<br>**----- End of picture text -----**<br>


**last modified:** 4/5/2026 

6AG10101AU004AA0 Page 6/6 

Subject to change without notice © Copyright Siemens 

5/10/2026