628281100000

**62 SЕRIES** 

## Power relays 16 A 

Road / tunnel lighting Industrial furnaces and ovens 

Burners, boilers and furnaces 

Control and management of electric power Punches, cleaners, planers and sanders 

Control panels 

Circuit breakers and switches 

Industrial motors 

FINDER reserves the right to alter characteristics at any time without notice. FINDER assumes no liability for damage to persons or property, caused as a result of the incorrect use or application of its products. 

**62 SERIES** 

**A** 

## **Printed circuit mount** 

## **62.22/62.23** 

## **62.22-0300/62.23-0300** 

## **16 A Power relay** 

- 2 & 3 Pole changeover contacts or NO (≥ 3 mm contact gap) 

- AC coils & DC coils 

- Reinforced insulation between coil and contacts according to EN 60335-1, with 6 mm clearance & 8 mm creepage distance 

- SELV coil-contact separator option 

- Cadmium free contact material options 

- 2 & 3 pole changeover contact 

- PCB mount 

   - 2 & 3 pole normally open contact (≥ 3 mm contact gap) 

   - PCB mount 

- Distance between contacts ≥ 3 mm (EN 60730-1). 

- ** With the AgSnO2 material the maximum peak current is 120 A - 5 ms (NO contact). 

_For UL ratings see:_ 

_“General technical information” page_ V 

**==> picture [515 x 432] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||||||||||
|---|---|---|---|---|---|---|---|---|---|
|62.22|62.23|62.22 - 0300|62.23 - 0300|
|For outline drawing see page 12|Copper side view|Copper side view|Copper side view|Copper side view|
|Contact specification|
|Contact configuration|2 CO (DPDT)|3 CO (3PDT)|2 NO (DPST-NO), ≥ 3 mm*|3 NO (3PST-NO), ≥ 3 mm*|
|Rated current/Maximum peak current|A|16/30**|16/30**|
|Rated voltage/|
|Maximum switching voltage|V AC|250/400|250/400|
|Rated load AC1|VA|4000|4000|
|Rated load AC15 (230 V AC)|VA|750|750|
|Motor rating (230/400 V AC)|kW|0.8/—|0.8/1.5|0.8/—|0.8/1.5|
|Breaking capacity DC1: 30/110/220 V|A|16/0.6/0.4|16/1.1/0.7|
|Minimum switching load|mW (V/mA)|1000 (10/10)|1000 (10/10)|
|Standard contact material|AgCdO|AgCdO|
|Coil specification|
|Nominal voltage (UN)|V AC (50/60 Hz)|6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400|
|V DC|6 - 12 - 24 - 48 - 60 - 110 - 125 - 220|
|Rated power AC/DC|VA (50 Hz)/W|2.2/1.3|3/3|
|Operating range|AC|(0.8…1.1)UN|(0.85…1.1)UN|
|DC|(0.8…1.1)UN|(0.85…1.1)UN|
|Holding voltage|AC/DC|0.8 UN / 0.6 UN|0.8 UN / 0.6 UN|
|Must drop-out voltage|AC/DC|0.2 UN / 0.1 UN|0.2 UN / 0.1 UN|
|Technical data|
|Mechanical life AC/DC|cycles|10 · 10|[6]|/30 · 10|[6]|10 · 10|[6]|/30 · 10|[6]|
|Electrical life at rated load AC1|cycles|100 · 10|[3]|100 · 10|[3]|
|Operate/release time|ms|11/4|15/3|
|Insulation between coil|
|and contacts (1.2/50 µs)|kV|6|6|
|Dielectric strength|
|between open contacts|V AC|1500|3000|
|Ambient temperature range|°C|–40…+70|–40…+50|
|Environmental protection|RT I|RT I|
|Approvals|(according to type)|@|Hl|®|B§|RINA|Miu|s|@S&|

**----- End of picture text -----**<br>


**3** 

**62 SERIES** 

## **Plug-in mount/Faston 187 16 A Power relay** 

- Plug-in (92 series sockets) or Faston 187 

- **A** (4.8 x 0.5 mm) with optional mounting adaptors • 2 & 3 Pole changeover contacts or NO 

- - (≥ 3 mm contact gap) 

## **62.32/62.33** 

## **62.32-0300/62.33-0300** 

- AC coils & DC coils 

- UL Listing (certain relay/socket combinations) 

- LED, mechanical indicator & test button options 

- Reinforced insulation between coil and contacts according to EN 60335-1, with 6 mm clearance & 8 mm creepage distance 

- SELV coil-contact separator option 

- Cadmium free contact material options 

- 2 & 3 pole changeover contact 

- Plug-in/Faston 187 

   - 2 & 3 pole normally open contact (≥ 3 mm contact gap) 

   - Plug-in/Faston 187 

- Sockets and accessories 

- European Patent 

- Distance between contacts ≥ 3 mm (EN 60730-1). 

- ** With the AgSnO2 material the maximum peak current is 120 A - 5 ms (NO contact). 

_For UL ratings see:_ 

## _“General technical information” page_ V 

**==> picture [518 x 423] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||||||||||
|---|---|---|---|---|---|---|---|---|---|
|For outline drawing see page 12|62.32|62.33|62.32-0300|62.33-0300|
|Contact specification|
|Contact configuration|2 CO (DPDT)|3 CO (3PDT)|2 NO (DPST-NO), ≥ 3 mm*|3 NO (3PST-NO), ≥ 3 mm*|
|Rated current/Maximum peak current|A|16/30**|16/30**|
|Rated voltage/|
|Maximum switching voltage|V AC|250/400|250/400|
|Rated load AC1|VA|4000|4000|
|Rated load AC15 (230 V AC)|VA|750|750|
|Motor rating (230/400 V AC)|kW|0.8/—|0.8/1.5|0.8/—|0.8/1.5|
|Breaking capacity DC1: 30/110/220 V|A|16/0.6/0.4|16/1.1/0.7|
|Minimum switching load|mW (V/mA)|1000 (10/10)|1000 (10/10)|
|Standard contact material|AgCdO|AgCdO|
|Coil specification|
|Nominal voltage (UN)|V AC (50/60 Hz)|6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400|
|V DC|6 - 12 - 24 - 48 - 60 - 110 - 125 - 220|
|Rated power AC/DC|VA (50 Hz)/W|2.2/1.3|3/3|
|Operating range|AC|(0.8…1.1)UN|(0.85…1.1)UN|
|DC|(0.8…1.1)UN|(0.85…1.1)UN|
|Holding voltage|AC/DC|0.8 UN / 0.6 UN|0.8 UN / 0.6 UN|
|Must drop-out voltage|AC/DC|0.2 UN / 0.1 UN|0.2 UN / 0.1 UN|
|Technical data|
|Mechanical life AC/DC|cycles|10 · 10|[6]|/30 · 10|[6]|10 · 10|[6]|/30 · 10|[6]|
|Electrical life at rated load AC1|cycles|100 · 10|[3]|100 · 10|[3]|
|Operate/release time|ms|11/4|15/3|
|Insulation between coil|
|and contacts (1.2/50 µs)|kV|6|6|
|Dielectric strength|
|between open contacts|V AC|1500|3000|
|Ambient temperature range|°C|–40…+70|–40…+50|
|Environmental protection|RT I|RT I|
|Approvals|(according to type)|C€@|G|EAL|®|B|RINA|Wis|

**----- End of picture text -----**<br>


**4** 

**62 SERIES** 

**A** 

## **Flange mount/Faston 250 16 A Power relay** 

## **62.82/62.83** 

## **62.82-0300/62.83-0300** 

- Faston 250 (6.3 x 0.8 mm) termination Flange or optional mounting adaptors 

- 2 & 3 Pole changeover contacts or NO (≥ 3 mm contact gap) 

- AC coils & DC coils 

- LED, mechanical indicator & test button options 

- Reinforced insulation between coil and contacts according to EN 60335-1, with 6 mm clearance & 8 mm creepage distance 

- SELV coil-contact separator option 

- Cadmium free contact material options 

- European Patent 

- 2 & 3 pole changeover contact 

- Flange mount/Faston 250 

   - 2 & 3 pole normally open contact (≥ 3 mm contact gap) 

   - Flange mount/Faston 250 

- Distance between contacts ≥ 3 mm (EN 60730-1). 

- ** With the AgSnO2 material the maximum peak current is 120 A - 5 ms (NO contact). 

_For UL ratings see:_ 

_“General technical information” page_ V 

||For outline drawing see page 12||62.82|62.83|||62.82-0300<br>62.83-0300|
|---|---|---|---|---|---|---|---|
||**Contact specification**|||||||
||Contact configuration||2 CO (DPDT)|3 CO (3PDT)|||2 NO (DPST-NO),≥3 mm*<br>3 NO (3PST-NO),≥3 mm*|
||Rated current/Maximum peak current<br>A||16/30**||||16/30**|
||Rated voltage/<br>Maximum switchingvoltage|V AC|250/400||||250/400|
||Rated load AC1|VA|4000||||4000|
||Rated load AC15 (230 V AC)|VA|750||||750|
||Motor rating (230/400 V AC)|kW|0.8/—|0.8/1.5|||0.8/—<br>0.8/1.5|
||Breaking capacity DC1: 30/110/220 V<br>A||16/0.6/0.4||||16/1.1/0.7|
||Minimum switching load|mW (V/mA)|1000 (10/10)||||1000 (10/10)|
||Standard contact material<br>**Coil specification**||AgCdO||||AgCdO|
||Nominal voltage (UN)|V AC (50/60 Hz)|6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400|||||
|||V DC||6 - 12 - 24 - 48 - 60 - 110 - 125 - 220||||
||Rated power AC/DC|VA (50 Hz)/W|2.2/1.3||||3/3|
||Operating range|AC|(0.8…1.1)UN||||(0.85…1.1)UN|
|||DC|(0.8…1.1)UN||||(0.85…1.1)UN|
||Holding voltage|AC/DC|0.8 UN/ 0.6 UN||||0.8 UN/ 0.6 UN|
||Must drop-out voltage<br>**Technical data**|AC/DC|0.2 UN/ 0.1 UN||||0.2 UN/ 0.1 UN|
||Mechanical life AC/DC|cycles|10 · 106/30 · 106||||10 · 106/30 · 106|
||Electrical life at rated load AC1|cycles|100 · 103||||100 · 103|
||Operate/release time|ms|11/4||||15/3|
||Insulation between coil|||||||
||and contacts(1.2/50µs)|kV|6||||6|
|X-2018, www.findernet.com|Dielectric strength<br>between open contacts<br>Ambient temperature range<br>Environmental protection<br>**Approvals**(according to type)|V AC<br>°C|1500<br>–40…+70<br>RT I<br>~~C€@~~|~~Gil~~|~~®~~|~~B~~|3000<br>–40…+50<br>RT I<br>~~BRINAWis~~|



**5** 

**62 SERIES** 

## **Plug-in mount/Faston 187 Magnetic blow power relay** 

## **62.31-4800** 

## **62.32-4800** 

- Plug-in (92 series sockets) or Faston 187 

**A** 

- (4.8 x 0.5 mm) with optional mounting adaptors 

- 1 & 2 Pole NO contacts 

- High DC load (resistive and inductive) switching capability 

- DC coils 

- Reinforced insulation between coil and contacts according to EN 60335-1, with 6 mm clearance & 8 mm creepage distance 

- Cadmium free contact material 

- Sockets and accessories 

- 1 pole normally open contact (double break, • 2 pole normally open contact ≥ 4.2 mm contact gap) (≥ 2.1 mm contact gap) 

- Plug-in/Faston 187 

   - Plug-in/Faston 187 

- Maximum peak current 120 A - 5 ms. 

|||62.31-4800|62.32-4800||
|---|---|---|---|---|
|For outline drawing see page 12|||||
|**Contact specification**<br>Contact configuration||1 NO (SPST-NO) double break, ≥ 4.2 mm|2 NO (DPST-NO), ≥ 2.1 mm||
|Rated current/Maximum peak current<br>A||16/30*|16/30*||
|Rated voltage/<br>Maximum switchingvoltage|V AC|250/400|250/400||
|Rated load AC1|VA|4000|4000||
|Breaking capacity DC1: 30/125/220 V|A|16/16/12|16/12/6||
|Breaking capacity DC inductive (L/R = 40 ms):<br>30/125/220 V|Breaking capacity DC inductive (L/R = 40 ms):<br>A|16/5/3|10/2/1.2||
|Minimum switching load|mW (V/mA)|1000 (10/10)|1000 (10/10)||
|Standard contact material||AgSnO2|AgSnO2||
|**Coil specification**<br>Nominal voltage (UN)|V DC|6 - 12 - 24 - 48 - 60 - 110 - 125 - 220|||
|Rated power DC|W|1.3|1.3||
|Operating range|DC|(0.85…1.1)UN|(0.85…1.1)UN||
|Holding voltage|DC|0.6 UN|0.6 UN||
|Must drop-out voltage<br>**Technical data**|DC|0.1 UN|0.1 UN||
|Mechanical life DC|cycles|10 · 106|10 · 106||
|Electrical life at rated load DC1|cycles|100 · 103|100 · 103||
|Operate/release time|ms|16/5|16/5||
|Insulation between coil|||||
|and contacts(1.2/50µs)|kV|kV<br>6|6||
|Dielectric strength<br>between open contacts<br>Ambient temperature range<br>Environmental protection<br>**Approvals**(according to type)|V AC<br>°C|3000<br>–40…+70<br>RT I|2000<br>–40…+70<br>RT I|X-2018, www.findernet.com|



**6** 

**62 SERIES** 

**A** 

## **Ordering information** 

Example:  62 series power relay + Faston 250 (6.3 x 0.8 mm), rear flange mount, 2 NO (DPST-NO), 12 V DC coil. 

**A B C D 6 2 . 8 2 . 9 . 0 1 2 . 0 3 0 0 Series A: Contact materialContact material D: Special versions Type** 0 = Standard AgCdO 0 

## **D: Special versions** 

- **A: Contact materialContact material** 0 = Standard AgCdO 4 =  AgSnO2 (standard for versions 4800) 

   - 0 = Standard 

   - 6 = Rear flange mount 9 =  Type 62.82/83 without rear flange mount 

- 2 = PCB 

- 3 = Plug-in 8 =  Faston 250 (6.3 x 0.8 mm) with rear flange mount 

- **B: Contact circuit** 

- 0 = CO (nPDT) **C: Options** 3 =  NO (nPST), 0 = None 2 = Mechanical indicator 

- ≥ 3 mm contact gap 

- 5 =  CO (nPDT) + additional physical 3 = LED (AC) separator between coil and contacts 4 =  Lockable test button + (for SELV applications) mechanical indicator 

## **No. of poles** 

- 1 = 1 pole (double break) 2 = 2 pole 

- 3 = 3 pole 

- **Coil version** 8 = AC (50/60 Hz) 

   - 5* = Lockable test button + LED (AC) 

- 6 =  NO (nPST), ≥ 3 mm contact gap + additional physical separator 54* =  Lockable test button + LED (AC) + between coil and contacts (for SELV mechanical indicator applications) 6* =  LED + diode 

9 = DC 

- **Coil voltage** applications) See coil specifications 8 =  NO (1 pole double break or 2 pole) (DC, polarity positive to pin A/A1) with magnetic blow 7* =  Lockable test button + LED + diode 

      - (DC, polarity positive to pin A/A1) 

   - 74* =  Lockable test button + LED + diode (DC, polarity positive to pin A/A1) + mechanical indicator 

*  Options not available for 220 V DC and 400 V AC versions. 

**Selecting features and options: only combinations in the same row are possible.** Preferred selections for best availability are shown in **bold.** 

|**Type**<br>~~a~~|**Coil version**|**A**|**B**|**C**|**D**|
|---|---|---|---|---|---|
|62.22/23<br>~~a~~<br>~~a~~|AC-DC<br>~~se~~|**0**- 4<br>~~se~~|**0**- 3 - 5 - 6|**0**|**0**|
|62.32/33<br>~~a~~<br>~~a~~<br>~~a~~<br>~~a~~<br>~~ss~~<br>~~a~~<br>~~a~~<br>~~a~~<br>~~a~~|AC-DC<br>~~se~~<br>~~a~~|0 - 4<br>~~se~~<br>~~ee~~|0 - 3 - 5 - 6<br>~~ee~~|0<br>~~ee~~|0  -  6<br>~~ee~~|
||AC-DC<br>~~a ~~<br>~~a~~|**0**- 4<br> ~~ee~~<br>~~ee~~|**0**- 5<br>~~ee~~<br>~~ee~~|2 -**4**<br>~~ee~~<br>~~ee~~|**0**- 6<br>~~ee~~<br>~~ee~~|
||AC<br>~~a ~~<br>~~a ~~|**0**- 4<br> ~~ee~~<br> ~~ee~~|**0**<br>~~ee~~<br>~~ee~~|2 - 3 -**4**- 5<br>~~ee~~<br>~~ee~~|**0**- 6<br>~~ee~~<br>~~ee~~|
||AC<br>~~ss~~|0 - 4<br>~~ss~~|0 - 3<br>~~ss~~|3<br>~~ss~~|0 - 6<br>~~ss~~|
||AC<br>~~a ~~<br>~~a~~|0 - 4<br> ~~ee~~<br>~~es~~|0<br>~~ee~~|54<br>~~ee~~|/<br>~~ee~~|
||DC<br>~~a~~|**0**- 4<br>~~es~~|**0**|**4**- 6 - 7|**0**- 6|
||DC<br>~~a~~<br>~~a~~|0 - 4<br>~~es~~|0 - 3|6|0 - 6|
||DC<br>~~a~~|0 - 4|0|74|/|
|62.31/32<br>~~a~~|DC<br>~~se~~|**4**<br>~~se~~|**8**|**0**|**0**|
|62.82/83<br>~~a~~<br>~~a~~<br>~~a~~<br>~~a~~<br>~~a~~<br>~~a~~|AC-DC<br>~~a~~|**0**- 4<br>~~ee~~|**0**- 3 - 5 - 6<br>~~ee~~|**0**<br>~~ee~~|**0**- 9<br>~~ee~~|
||AC-DC<br>~~a ~~<br>~~a~~|0 - 4<br> ~~ee~~|0 - 5<br>~~ee~~|2 - 4<br>~~ee~~|0<br>~~ee~~|
||AC<br>~~a~~<br>~~a~~|0 - 4<br>~~a~~|0|2 - 3 - 4 - 5|0|
||AC<br>~~a~~<br>~~a~~<br>~~a~~|0 - 4<br>~~a~~<br>~~es~~|0 - 3|3|0|
||DC<br>~~a~~<br>~~a~~|0 - 4<br>~~es~~<br>~~ee~~|0|4 - 6 - 7|0|
||DC<br>~~a~~|0 - 4<br>~~es~~<br>~~ee~~|0 - 3|6|0|



## **Descriptions: Options and Special versions** 

**C: Option 3, 5, 54** LED (AC) 

**C: Option 6, 7, 74** LED + diode (DC, polarity positive to pin A/A1) 

**==> picture [171 x 93] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 3<br>2<br>X-2018, www.findernet.com<br>**----- End of picture text -----**<br>


**B: Contact circuit 8** Magnetic blow 

**B: Contact circuit 5, 6** Additional physical separator between coil and contacts 

(for SELV applications) **Lockable test button and mechanical flag indicator (0040, 0050, 0054, 0070, 0074)** The dual-purpose Finder test button can be used in two ways: E 

Case 1) The plastic pip (located directly above the test button) remains intact. In this case, when the test button is pushed, the contacts operate. When the test button is released the contacts return to their former state. 

Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition to the above function), when the test button is pushed and rotated, the contacts are latched in the operating state, and remain so until the test button is rotated back to its former position. In both cases ensure that the test button actuation is swift and decisive. 

**7** 

**62 SERIES** 

## **Technical data** 

## **Insulation according to EN 61810-1** 

**A** 

|||**2 CO - 3 CO**|**2 CO - 3 CO**|**2 NO - 3 NO**|**2 NO - 3 NO**|**1 NO***|**1 NO***|**2 NO***|**2 NO***|
|---|---|---|---|---|---|---|---|---|---|
|Nominal voltage of supply system<br>V AC||230/400||230/400||230/400||230/400||
|Rated insulation voltage<br>V AC||400||400||400||400||
|Pollution degree||3||3||3||3||
|**Insulation between coil and contact set**||||||||||
|Type of insulation||Reinforced||Reinforced||Reinforced||Reinforced||
|Overvoltage category||III||III||III||III||
|Rated impulse voltage<br>kV (1.2/50 µs)||6||6||6||6||
|Dielectric strength<br>V AC||4000||4000||4000||4000||
|**Insulation between adjacent contacts**||||||||||
|Type of insulation||Basic||Basic||—||Basic||
|Overvoltage category||III||III||—||III||
|Rated impulse voltage<br>kV (1.2/50 µs)||4||4||—||4||
|Dielectric strength<br>V AC||2500||2500||—||2500||
|**Insulation between open contacts**||||||||||
|Type of disconnection||Micro-disconnection||Full-disconnection||Full-disconnection||Full-disconnection**||
|Overvoltage category||—||III||III||II||
|Rated impulse voltage<br>kV (1.2/50 µs)||—||4||4||2.5||
|Dielectric strength<br>V AC/kV (1.2/50 µs)||1500/2||3000/4||3000/4||2000/2.5||
|**Insulation between coil terminals**||||||||||
|Rated impulse voltage (surge) differential mode<br>(according to EN 61000-4-5)<br>kV(1.2/50 µs)||4||||||||
|**Other data**||||||||||
|Bounce time: NO/NC<br>ms||1/5<br>(changeover)||3/—<br>(normallyopen)||3/—<br>(normallyopen)||3/—<br>(normallyopen)||
|Vibration resistance (10…150)Hz: NO/NC<br>g||20/8||||||||
|Shock resistance|g|15||||||||
|Power lost to the environment|without contact current<br>W|**2 pole (CO) **|**3 pole (CO) **||**2 pole (NO) **|**3 pole (NO) **|**1 pole (NO)***||**2 pole (NO)***|
|||1.3|1.3||3|3|1.3||1.3|
||with rated current<br>W|3.3|4.3||5|6|3||3.3|
|Recommended distance between relays mounted on PCB<br>mm||≥ 5|||||—|||



* Magnetic blow version 

** Only in applications where over voltage category II is permitted. In applications of over voltage category III: Micro-disconnection. 

**8** 

**62 SERIES** 

**A** 

## **Contact specification** 

## **F 62 - Electrical life (AC) v contact current** 

**==> picture [511 x 317] intentionally omitted <==**

**----- Start of picture text -----**<br>
Resistive load - cos ϕ  = 1<br>Inductive load - cos ϕ  = 0.4<br>H 62 -  Maximum DC1 breaking capacity  H 62 -  Maximum DC1 breaking capacity<br>Changeover contacts Normally open contacts<br>contacts in series contacts in series<br>Voltage DC (V) Voltage DC (V)<br>Cycles<br>DC breaking current (A) DC breeaking current (A)<br>**----- End of picture text -----**<br>


- When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of ≥ 100 · 10[3] can be expected. 

- In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load. Note: the release time of the load will be increased. 

## **H 62 - Maximum DC breaking capacity 62.31.9.xxx.4800** 

## **H 62 - Maximum DC breaking capacity 62.32.9.xxx.4800** 

**==> picture [511 x 143] intentionally omitted <==**

**----- Start of picture text -----**<br>
50 50<br>DC1 DC1<br>10 10<br>DC13<br>1 L/R = 40 ms 1 DC13<br>L/R = 40 ms<br>0.1 0.1<br>20 60 100 140 180 220 260 20 60 100 140 180 220 260<br>(V) (V)<br>Voltage DC (V) Voltage DC (V)<br>DC breaking current (A) DC breeaking current (A)<br>**----- End of picture text -----**<br>


- When switching a resistive load (DC1), or a DC13 load with a diode in parallel to the load, having voltage and current values under the DC1 curve, an electrical life of ≥ 100 · 10[3] can be expected. Note: the release time for the load will be increased. 

- When switching a DC13 load without a diode in parallel to the load, the DC13 curve applies and an electrical life of ≥ 80 · 10[3] can be expected. 

**9** 

**62 SERIES** 

## **Coil specifications** 

||**Coil specifications**|**Coil specifications**|**Coil specifications**|**Coil specifications**|**Coil specifications**|**Coil specifications**|
|---|---|---|---|---|---|---|
|**A**|**DC version data**||||||
||Nominal<br>voltage<br>UN|Coil<br>code|Operating range<br>Umin<br>Umax||Resistance<br>R|Rated coil<br>consumption<br>Iat UN|
||V||V|V|Ω|mA|
||6|**9**.006|4.8|6.6|28|214|
||12|**9**.012|9.6|13.2|110|109|
||24|**9**.024|19.2|26.4|445|54|
||48|**9**.048|38.4|52.8|1770|27|
||60|**9**.060|48|66|2760|21.7|
||110|**9**.110|88|121|9420|11.7|
||125|**9**.125|100|138|12000|10.4|
||220|**9**.220|176|242|37300|5.8|



## **DC (NO/nPST-NO) version data - ≥ 3 mm** 

|Nominal<br>voltage<br>UN|Coil<br>code|Operating range<br>Umin<br>Umax|Operating range<br>Umin<br>Umax|Resistance<br>R|Rated coil<br>consumption<br>Iat UN|
|---|---|---|---|---|---|
|V||V|V|Ω|mA|
|6|**9**.006|5.1|6.6|12|500|
|12|**9**.012|10.2|13.2|48|250|
|24|**9**.024|20.4|26.4|192|125|
|48|**9**.048|40.8|52.8|770|63|
|60|**9**.060|51|66|1200|50|
|110|**9**.110|93.5|121|4200|26|
|125|**9**.125|106|138|5200|24|
|220|**9**.220|187|242|17600|12.5|



## **AC version data** 

**==> picture [253 x 47] intentionally omitted <==**

**----- Start of picture text -----**<br>
Nominal  Coil  Rated coil<br>voltage code Operating range Resistance consumption<br>UN Umin Umax R I at UN (50Hz)<br>V V V Ω mA<br>**----- End of picture text -----**<br>


|Nominal<br>voltage<br>UN<br>V|Coil<br>code|Operating range<br>Umin<br>Umax<br>V<br>V|Operating range<br>Umin<br>Umax<br>V<br>V|Resistance<br>R<br>Ω|Rated coil<br>consumption<br>Iat UN(50Hz)<br>mA|
|---|---|---|---|---|---|
|6|**8**.006|4.8|6.6|4.6|367|
|12|**8**.012|9.6|13.2|19|183|
|24|**8**.024|19.2|26.4|74|90|
|48|**8**.048|38.4|52.8|290|47|
|60|**8**.060|48|66|450|37|
|110|**8**.110|88|121|1600|20|
|120|**8**.120|96|132|1940|18.6|
|230|**8**.230|184|253|7250|10.5|
|240|**8**.240|192|264|8500|9.2|
|400|**8**.400|320|440|19800|6|



## **AC (NO/nPST-NO) version data - ≥ 3 mm** 

**==> picture [253 x 47] intentionally omitted <==**

**----- Start of picture text -----**<br>
Nominal  Coil  Rated coil<br>voltage code Operating range Resistance consumption<br>UN Umin Umax R I at UN (50Hz)<br>V V V Ω mA<br>**----- End of picture text -----**<br>


|Nominal<br>voltage<br>UN<br>V|Coil<br>code|Operating range<br>Umin<br>Umax<br>V<br>V|Operating range<br>Umin<br>Umax<br>V<br>V|Resistance<br>R<br>Ω|Rated coil<br>consumption<br>Iat UN(50Hz)<br>mA|
|---|---|---|---|---|---|
|6|**8**.006|5.1|6.6|4|540|
|12|**8**.012|10.2|13.2|14|275|
|24|**8**.024|20.4|26.4|62|130|
|48|**8**.048|40.8|52.8|220|70|
|60|**8**.060|51|66|348|55|
|110|**8**.110|93.5|121|1200|30|
|120|**8**.120|106|137|1350|24|
|230|**8**.230|196|253|5000|14|
|240|**8**.240|204|264|6300|12.5|
|400|**8**.400|340|440|14700|7.8|



## **DC (NO/nPST-NO) magnetic blow version - ≥ 2.1 mm or ≥ 4.2 mm** 

|Nominal<br>voltage<br>UN|Coil<br>code|Operating range<br>Umin<br>Umax|Operating range<br>Umin<br>Umax|Resistance<br>R|Rated coil<br>consumption<br>Iat UN|
|---|---|---|---|---|---|
|V||V|V|Ω|mA|
|6|**9**.006|5.1|6.6|28|214|
|12|**9**.012|10.2|13.2|110|109|
|24|**9**.024|20.4|26.4|445|54|
|48|**9**.048|40.8|52.8|1770|27|
|60|**9**.060|51|66|2760|21.7|
|110|**9**.110|93.5|121|9420|11.7|
|125|**9**.125|106|138|12000|10.4|
|220|**9**.220|154*|242|37300|5.8|



* Special version with Umin = 70% UN 

**10** 

**62 SERIES** 

**A** 

## **Coil specifications** 

**==> picture [191 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
R 62 -  DC coil operating range v ambient temperature<br>Changeover contacts<br>**----- End of picture text -----**<br>


**==> picture [191 x 19] intentionally omitted <==**

**----- Start of picture text -----**<br>
R 62 -  AC coil operating range v ambient temperature<br>Changeover contacts<br>**----- End of picture text -----**<br>


**==> picture [511 x 142] intentionally omitted <==**

**1 -** Max. permitted coil voltage. 

**2 -** Min. pick-up voltage with coil at ambient temperature. 

**==> picture [104 x 8] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 -   Max. permitted coil voltage.<br>**----- End of picture text -----**<br>


**==> picture [192 x 9] intentionally omitted <==**

**----- Start of picture text -----**<br>
2 -   Min. pick-up voltage with coil at ambient temperature.<br>**----- End of picture text -----**<br>


**R 62 -  DC coil operating range v ambient temperature** Normally open contacts 

**R 62 -  AC coil operating range v ambient temperature** Normally open contacts 

**==> picture [511 x 142] intentionally omitted <==**

**1 -** Max. permitted coil voltage. **1 -** Max. permitted coil voltage. **2 -** Min. pick-up voltage with coil at ambient temperature. **2 -** Min. pick-up voltage with coil at ambient temperature. 

## **R 62 -  DC coil operating range v ambient temperature** 

Normally open contacts - magnetic blow version 

**==> picture [251 x 142] intentionally omitted <==**

**1 -** Max. permitted coil voltage. 

**2 -** Min. pick-up voltage with coil at ambient temperature. 

**11** 

**62 SERIES** 

## **Outline drawings** 

Type  62.22 Type  62.23 Type 62.2x Type 62.2x-0300 62.22-0300 62.23-0300 **A** Type  62.32 Type  62.33 Type 62.3x Type 62.3x-0300 62.32-0300 62.33-0300 Type  62.82 Type  62.83 Type 62.8x Type 62.8x-0300 62.82-0300 62.83-0300 

**==> picture [303 x 124] intentionally omitted <==**

Type 62.31-4800 Type 62.32-4800 

**==> picture [54 x 107] intentionally omitted <==**

**==> picture [66 x 111] intentionally omitted <==**

**==> picture [66 x 111] intentionally omitted <==**

**12** 

**62 SERIES** 

**A** 

## **Accessories** 

**==> picture [409 x 687] intentionally omitted <==**

**----- Start of picture text -----**<br>
mal ¢ Mounting adaptor  47.2 x for types 62.3x and 62.8x.xxxx.xxx9 (M4)  a 45.6 2 062.10<br>062.10 —— ms 87 4.8<br>OW<br>—, OT 6<br>asm e = =<br>ay :- » 8©<br>=<br>+ a oO =<br>= | 472<br>i m a<br>062.10 with relay 062.10 062.10 with relay<br>Flange mounting adaptor  for types 62.3x and 62.8x.xxxx.xxx9  062.60<br>=<br>S a<br>45.6<br>062.60<br>N<br>g E F,<br>i<br>< - cl |<br>a Z a 3. 4® G]= _ — —_____J<br>062.60 with relay ~NeU U<br>062.60 062.60 with relay<br>Top flange mount  for types 62.3x and 62.8x.xxxx.xxx9  062.05<br>a 28 3 46.1 1.7<br>z 40.6<br>062.05 +<br>= 1 582 7 83<br>is<br>062.05 with relay 062.05 062.05 with relay<br>Top 35 mm rail (EN 60715) mount  for types 62.3x and 62.8x.xxxx.xxx9 062.07<br>78<br>| on 30 me 55 —“6s S s<br>> 062.07 —| /| —— N +<br>o— =— — - i—— lJ<br>15 8 46.1 ce° 4A<br>l Cir<br>062.07 with relay 062.07 062.07 with relay<br>Rear 35 mm rail (EN 60715) mount  for types 62.3x and 62.8x.xxxx.xxx9 062.08<br>=><br>30 2 35.4<br>062.08<br>Sal ae, | ea Se ¥<br>+6 (e)- XN2 II} ==| = |S) =ZS) [f]] +<br>3 51.1 | 40.6<br>062.08 with relay 062.08 062.08 with relay<br>Sheet of marker tags (CEMBRE Thermal transfer printers)  for 62 series relays,<br>= — | — e434<br>2Peeoee Be plastic, 48 tags, 6 x 12 mm 060.48<br>**----- End of picture text -----**<br>


**060.48** 

**13** 

**62 SERIES** 

**==> picture [10 x 10] intentionally omitted <==**

**----- Start of picture text -----**<br>
A<br>**----- End of picture text -----**<br>


|**Screw terminal (Box clamp) socket**<br>panel or 35 mm rail (EN 60715) mount<br>For relay type<br>**Accessories**<br>Metal retaining clip<br>(supplied with socket -packagingcode SMA)|**92.03**<br>**Blue**<br>**92.03.0**<br>**Black**<br>62.31, 62.32, 62.33<br>092.71|**92.03**<br>**Blue**<br>**92.03.0**<br>**Black**<br>62.31, 62.32, 62.33<br>092.71|
|---|---|---|
|Identification tag|092.00.2||
|Modules (see table below)|99.02||
|Timer modules (see table below)<br>**Technical data**<br>Rated values|86.00, 86.30<br>16 A - 250 V||
|Dielectric strength|6 kV (1.2/50µs) between coil and contacts||
|Protection category|IP 20||
|Ambient temperature<br>°C|–40…+70 (see diagram L92)||
|Screw torque<br>Nm|0.8||
|Wire striplength<br>mm|10||
|Max. wire size for 92.03 socket<br>mm2 <br>AWG|solid wire|stranded wire|
||1 x 10 / 2 x 4|1 x 6 / 2 x 4|
||1 x 8 / 2 x 12|1 x 10 / 2 x 12|



## **L 92 - Rated current v ambient temperature** 

**==> picture [7 x 50] intentionally omitted <==**

**----- Start of picture text -----**<br>
Rated current (A)<br>**----- End of picture text -----**<br>


**==> picture [18 x 6] intentionally omitted <==**

**----- Start of picture text -----**<br>
86.00<br>**----- End of picture text -----**<br>


**86.30** Co iJ **99.02** Approvals (according to type): 

DC Modules with non-standard polarity (+A2) on request. 

|Multi-voltage: (12…240)V AC/DC;<br>Multi-functions: AI,DI,SW,BE,CE,DE,EE,FE; (0.05 s…100 h)|86.00.0.240.0000|
|---|---|
|(12…24)V AC/DC; Bi-function: AI, DI; (0.05 s…100 h)|86.30.0.024.0000|
|(110...125)V AC; Bi-function: AI, DI; (0.05 s…100 h)|86.30.8.120.0000|
|(230...240)V AC; Bi-function: AI, DI; (0.05 s…100 h)|86.30.8.240.0000|



|Diode (+A1, standardpolarity)<br>(6...220)V DC|99.02.3.000.00|
|---|---|
|LED<br>(6...24)V DC/AC|99.02.0.024.59|
|LED<br>(28...60)V DC/AC|99.02.0.060.59|
|LED<br>(110...240)V DC/AC|99.02.0.230.59|
|LED + Diode (+A1, standardpolarity)<br>(6...24)V DC|99.02.9.024.99|
|LED + Diode (+A1, standardpolarity)<br>(28...60)V DC|99.02.9.060.99|
|LED + Diode (+A1, standardpolarity)<br>(110...220)V DC|99.02.9.220.99|
|LED + Varistor<br>(6...24)V DC/AC|99.02.0.024.98|
|LED + Varistor<br>(28...60)V DC/AC|99.02.0.060.98|
|LED + Varistor<br>(110...240)V DC/AC|99.02.0.230.98|
|RC circuit<br>(6...24)V DC/AC|99.02.0.024.09|
|RC circuit<br>(28...60)V DC/AC|99.02.0.060.09|
|RC circuit<br>(110...240)V DC/AC|99.02.0.230.09|
|Residual current by-pass<br>(110...240)V AC|99.02.8.230.07|



**14** 

**62 SERIES** 

**==> picture [464 x 108] intentionally omitted <==**

**----- Start of picture text -----**<br>
||||
|---|---|---|
|PCB socket|92.13 (blue)|92.13.0 (black)|
|For relay type|62.31, 62.32, 62.33|
|<|Accessories|
|92.13|
|Metal retaining clip|
|Approvals|(supplied with socket - packaging code SMA)|092.54|
|(according to type):|
|Technical data|
|@FAL AXis@|Rated values|10 A - 250 V|
|Dielectric strength|2.5 kV AC|
|Ambient temperature|°C|–40…+70|

**----- End of picture text -----**<br>


**==> picture [10 x 10] intentionally omitted <==**

**----- Start of picture text -----**<br>
A<br>**----- End of picture text -----**<br>


62.3x plug on 92.13 is 63.3 mm high 

**==> picture [374 x 105] intentionally omitted <==**

**----- Start of picture text -----**<br>
|||||||
|---|---|---|---|---|---|
|Panel mount solder socket|mounted with M3 screw|92.33 (blue)|
|For relay type|62.31, 62.32, 62.33|
|Accessories|
|92.33|Metal retaining clip|
|Approvals|(supplied with socket - packaging code SMA)|092.54|
|(according to type):|
|Technical data|
|Ce|@|FAL|®|Rated values|10 A - 250 V|
|CALs|Dielectric strength|2.5 kV AC|
|Ambient temperature|°C|–40…+70|

**----- End of picture text -----**<br>


## **Packaging codes** 

**How to code and identify retaining clip and packaging options for sockets.** 

Example: 

**9 2 . 0 3 S M A** 

**9 2 . 0** 

**==> picture [9 x 11] intentionally omitted <==**

**----- Start of picture text -----**<br>
3<br>**----- End of picture text -----**<br>


**A** Standard packaging **SM** Metal retaining clip Without retaining clip 

Please see general technical information 

**15**