3UF7013-1AB00-0

**3UF7013-1AB00-0** 

**Data sheet** 

basic device SIMOCODE pro V EIP, EtherNet/IP, media redundancy, DLR (max. 20 participants) web server, transfer rate 100 Mbps, 2 x bus connection via RJ45, 4 I/3 O freely configurable, Us: 24 V DC, input for thermistor connection monostable relay outputs, expandable by expansion modules 

|**product brand name**|SIMOCODE|
|---|---|
|**product designation**|Motor management system|
|**design of theproduct**|basic unit 3|
|**product type designation**|pro V EIP|
|**General technical data**||
|**product function**||
|● current measurement|No|
|● voltage measurement|No|
|● activepower measurement|Yes|
|● energymeasurement|No|
|● frequencymeasurement|No|
|● bus communication|Yes|
|● data acquisition function|Yes|
|● diagnostics function|Yes|
|●passwordprotection|Yes|
|● test function|Yes|
|● maintenance function|Yes|
|● MRRT redundancy procedure|No|
|**product component**||
|● input for thermistor connection|Yes|
|● digital input|Yes|
|● input for analogtemperature sensors|No|
|● input forground fault detection|No|
|● relayoutput|Yes|
|**product extension**||
|● temperature monitoringmodule|Yes|
|● current measuringmodule|Yes|
|● current/voltage measuringmodule|Yes|
|● fail-safe digital I/O module|Yes|
|●ground-fault monitoringmodule|Yes|
|● decouplingmodule|Yes|
|● analogI/O module|Yes|
|● digital I/O module with monostable outputs|Yes|
|● digital I/O module with bistable outputs|Yes|
|● control unit with display|Yes|
|● control unit|Yes|
|**consumed activepower**|3.9 W|
|insulation voltage with degree ofpollution 3 at AC rated value|300 V|
|**surge voltage resistance rated value**|4 000 V|



Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 1/7 

6/2/2026 

||**shock resistance**|||
|---|---|---|---|
||**● according to IEC 60068-2-27**|15g/ 11 ms||
|||||
||**● vibration resistance**|1 … 6 Hz / 15 mm; 6 … 500 Hz / 2g||
||**switching capacity current of the NO contacts of the relay**<br>**outputs at AC-15**|||
||● at 24 V|6 A||
||● at 120 V|6 A||
||● at 230 V|3 A||
||**switching capacity current of the NO contacts of the relay**<br>**outputs at DC-13**|||
||● at 24 V|2 A||
||● at 60 V|0.55 A||
||● at 125 V|0.25 A||
||**mechanical service life(operating cycles) typical**|10 000 000||
||electrical endurance(operatingcycles)typical|100 000||
||**buffering time in the event ofpower failure**|0.02 s||
||**reference code according to IEC 81346-2**|F||
||continuous current of the NO contacts of the relayoutputs|||
||● at 50 °C|6 A||
||● at 60 °C|5 A||
||**type of input characteristic**|Type 1 in accordance with EN 61131-2||
||**Substance Prohibitance(day/month/year)**|03/01/2017||
||**SVHC substance name**|Lead CAS-No. 7439-92-1<br>Lead monoxide (lead oxide) CAS-No. 1317-36-8<br>2-methyl-1-(4-methylthiophenyl)-2-morpholinopropan-1-one CAS-No. 71868-<br>10-5<br>Melamine CAS-No. 108-78-1<br>4,4'-isopropylidenediphenol(Bisphenol A, BPA)CAS-No. 80-05-7||
||**Net Weight**|0.32 kg||
||**Electromagnetic compatibility**|||
||EMC emitted interference accordingto IEC 60947-1|class A||
||EMC immunityaccordingto IEC 60947-1|corresponds to degree of severity3||
||**conducted interference**|||
||● due to burst accordingto IEC 61000-4-4|2 kV(powerports)/ 1 kV(signalports)||
||● due to conductor-earth surge accordingto IEC 61000-4-5|2 kV||
||● due to conductor-conductor surge according to IEC<br>61000-4-5|1 kV||
||● due to high-frequency radiation according to IEC 61000-<br>4-6|10 V||
||**field-based interference according to IEC 61000-4-3**|10 V/m||
||**electrostatic discharge according to IEC 61000-4-2**|6 kV contact discharge / 8 kV air discharge||
||**conducted HF interference emissions according to**<br>**CISPR11**|corresponds to degree of severity A||
||**field-bound HF interference emission according to CISPR11**|corresponds to degree of severityA||
||**Inputs/ Outputs**|||
||**product function**|||
||●parameterizable inputs|Yes||
||●parameterizable outputs|Yes||
||**number of inputs**|4||
||● for thermistor connection|1||
||number of digital inputs with a common referencepotential|4||
||**digital input version**|||
||● type 1 acc. to IEC 61131|Yes||
||**input voltage at digital input at DC**|||
||● rated value|24 V||
||**number of outputs**|3||
||**number of semiconductor outputs**|0||
||**number of outputs as contact-affected switching element**|3||
||**switching behavior**|monostable||
||**number of relay outputs**|3||
||**type of relay outputs**|Monostable||



Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 2/7 

6/2/2026 

||**wire length for digital signals maximum**|300 m||
|---|---|---|---|
||**wire length for thermistor connection**|||
||● with conductor cross-section = 0.5 mm² maximum|50 m||
||● with conductor cross-section = 1.5 mm² maximum|150 m||
||● with conductor cross-section = 2.5 mm² maximum|250 m||
||**Protective and monitoring functions**|||
||**product function**|||
||● asymmetrydetection|Yes||
||● blockingcurrent evaluation|Yes||
||●power factor monitoring|Yes||
||●ground fault detection|Yes||
||●ground-fault monitoring|No||
||●phase failure detection|Yes||
||●phase sequence recognition|Yes||
||● voltage detection|Yes||
||● monitoringof number of start operations|Yes||
||● overvoltage detection|Yes||
||● overcurrent detection 1phase|Yes||
||● undervoltage detection|Yes||
||● undercurrent detection 1phase|Yes||
||● activepower monitoring|Yes||
||**product function**|||
||● current detection|Yes||
||● overloadprotection|Yes||
||● evaluation of thermistor motorprotection|Yes||
||**total cold resistance number of sensors in series maximum**|1.5 kΩ||
||**response value of thermoresistor**|3 400 ... 3 800 Ω||
||● of the short-circuit control|9 Ω||
||**release value of thermoresistor**|1 500 ... 1 650 Ω||
||**Motor control functions**|||
||**product function**|||
||●parameterizable overload relay|Yes||
||● circuit breaker control|Yes||
||● direct start|Yes||
||● reverse starting|Yes||
||● star-delta circuit|Yes||
||● star-delta reversingcircuit|Yes||
||● Dahlander circuit|Yes||
||● Dahlander reversingcircuit|Yes||
||●pole-changingswitch circuit|Yes||
||●pole-changingswitch reversingcircuit|Yes||
||● slide control|Yes||
||● valve control|Yes||
||**Communication/ Protocol**|||
||**protocol is supported**|||
||● PROFIBUS DPprotocol|No||
||● PROFINET IOprotocol|No||
||● PROFIsafeprotocol|No||
||● Modbus RTU|No||
||● EtherNet/IP|Yes||
||● OPC UA Server|No||
||● LLDP|Yes||
||● Address Resolution Protocol(ARP)|Yes||
||● SNMP|Yes||
||● HTTPS|No||
||● NTP|Yes||
||● Media RedundancyProtocol(MRP)|No||
||**product function**|||
||● web server|Yes||



Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 3/7 

6/2/2026 

|● shared device|No|
|---|---|
|● at the Ethernet interface Autocrossover|Yes|
|● at the Ethernet interface Autonegotiation|Yes|
|● at the Ethernet interface Autosensing|Yes|
|● is supported Device Level Ring (DLR)|Yes|
|● is supported PROFINET system redundancy (S2)|No|
|● supports PROFIenergymeasured values|No|
|● supports PROFIenergyshutdown|No|
|**transfer rate maximum**|100 Mbit/s|
|**identification & maintenance function**||
|● I&M0 - device-specific information|No|
|● I&M1 - higher level designation/location designation|No|
|● I&M2 - installation date|No|
|● I&M3 - comment|No|
|type of electrical connection of the communication interface|2x RJ45|
|**Installation/ mounting/ dimensions**||
|**mounting position**|any|
|**fastening method**|screw and snap-on mounting|
|**height**|111 mm|
|**width**|45 mm|
|**depth**|124 mm|
|**required spacing**||
|● top|40 mm|
|● bottom|40 mm|
|● left|0 mm|
|● right|0 mm|
|**Connections/ Terminals**||
|**product component removable terminal for auxiliary and**<br>**control circuit**|Yes|
|**type of electrical connection**||
|● for auxiliaryand control circuit|screw-type terminals|
|**type of connectable conductor cross-sections**||
|● solid|1x(0.5 ... 4.0mm²), 2x(0.5 ... 2.5 mm²)|
|● finelystranded with core endprocessing|1x(0.5 ... 2.5 mm²), 2x(0.5 ... 1.5 mm²)|
|● for AWG cables solid|1x(20 ... 12), 2x(20 ... 14)|
|● for AWG cables stranded|1x(20 ... 14), 2x(20 ... 16)|
|tighteningtorque with screw-type terminals|0.8 ... 1.2 N·m|
|tighteningtorque [lbf·in] with screw-type terminals|7 ... 10.3 lbf·in|
|**Ambient conditions**||
|installation altitude at height above sea level maximum|2 000 m|
|● note|Restrictions apply to higher installation altitudes, see:<br>https://support.industry.siemens.com/cs/document/109995153|
|**ambient temperature**||
|● duringoperation|-25 ... +60 °C|
|● duringstorage|-40 ... +80 °C|
|● duringtransport|-40 ... +80 °C|
|**environmental category**||
|● during operation according to IEC 60721|3K6 (no formation of ice, no condensation, relative humidity 10 ... 95%), 3C3<br>(no salt mist), 3S2(sand must notget into the devices), 3M6|
|● during storage according to IEC 60721|1K6 (no condensation, relative humidity 10 ... 95%), 1C2 (no salt mist), 1S2<br>(sand must notget into the devices), 1M4|
|● duringtransport accordingto IEC 60721|2K2, 2C1, 2S1, 2M2|
|**relative humidity**||
|● duringoperation|5 ... 95 %|
|**contact rating of auxiliary contacts according to UL**|B300 / R300|
|**Short-circuit protection**||
|design of short-circuit protection per output|Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-<br>breaker C char.: 1.6 A(IEC 60947-5-1)or 6 A(I_K < 500 A)|
|Electrical Safety||
|**touch protection against electrical shock**|finger-safe|



Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 4/7 

6/2/2026 

|**ATEX**<br>~~SS~~|**ATEX**<br>~~SS~~|**ATEX**<br>~~SS~~|**ATEX**<br>~~SS~~|**ATEX**<br>~~SS~~|
|---|---|---|---|---|
|**certificate of suitability**|||||
|● IECEx||Yes; IECEx BVS 20.0020 / IECEx PTB 18.0004X|||
|● accordingto ATEX directive 2014/34/EU||BVS 06 ATEX F001, PTB 18 ATEX 5003 X|BVS 06 ATEX F001, PTB 18 ATEX 5003 X||
|● acc. to Equipment and Protective System Intended for||ITS21UKEX0464, ITS21UKEX0455X|||
|Use in Potentially Explosive Atmospheres Regulations|||||
|2016(S.I. 2016 No.1107)|||||
|● accordingto UKCA||ITS21UKEX0464, ITS21UKEX0455X|||
|**Galvanic isolation**<br>~~Pn~~|||||
|**(electrically) protective separation according to IEC 60947-1**||All circuits with protective separation (double creepage paths and clearances),|||
|||the information in the "Protective Separation" test report, No. A0258, must be|||
|||observed(link see further information)|||
|**design of the electrical isolation**||Protective separation in accordance with IEC 60947-1 for all circuits|aration in accordance with IEC 60947-1 for all circuits||
|● note||Test report No. A0258 must be observed|Test report No. A0258 must be observed||
|||(https://support.industry.siemens.com/cs/document/109748152)|||
|**Control circuit/ Control**<br>~~ES~~|||||
|**product function soft starter control**||Yes|||
|**type of voltage of the control supply voltage**||DC|||
|**control supply voltage at DC rated value**||24 V|||
|**control supply voltage 1 at DC rated value**||24 V|||
|**operating range factor control supply voltage rated value at**|**operating range factor control supply voltage rated value at**||||
|**DC**|||||
|● initial value||0.85|||
|● full-scale value||1.2|||
|**inrush currentpeak**|||||
|● at 24 V||17 A|||
|**duration of inrush currentpeak**|||||
|● at 24 V||1.1 ms|||
|**Approvals Certificates**<br>~~ES~~|||||
|**Environment**|**General Product Approval**||||
|Environmental Con-|||||
|firmations|||||
|**General Product Ap-**<br>**proval**<br>**EMV**||**For use in hazardous locations**|||
||||||
|**For use in hazardous locations**|**Test Certificates**|||**Maritime application**|
|Miscellaneous<br>=|Special Test Certific-<br>ate<br>Type Test Certific-<br>ates/Test Report<br>Special Test Certific-<br>ate<br>~~Ss~~Cr?||||
|**Maritime application**<br>**other**<br>Confirmation<br>Miscellaneous<br>~~=e—~~|||||
|**other**|||||



Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 5/7 

6/2/2026 

Confirmation 

**Further information Information on the packaging** https://support.industry.siemens.com/cs/ww/en/view/109813875 **Information for data generation and storage** https://support.industry.siemens.com/cs/ww/en/view/109995012 **Information- and Downloadcenter (Catalogs, Brochures,…)** https://www.siemens.com/ic10 **Industry Mall (Online ordering system)** https://mall.industry.siemens.com/mall/en/en/Catalog/product?mlfb=3UF7013-1AB00-0 **Cax online generator** https://support.automation.siemens.com/WW/CAXorder/default.aspx?lang=en&mlfb=3UF7013-1AB00-0 **Service&Support (Manuals, Certificates, Characteristics, FAQs,...)** https://support.industry.siemens.com/cs/ww/en/ps/3UF7013-1AB00-0 **Image database (product images, 2D dimension drawings, 3D models, device circuit diagrams, EPLAN macros, ...)** https://www.automation.siemens.com/bilddb/cax_de.aspx?mlfb=3UF7013-1AB00-0&lang=en 

**==> picture [203 x 225] intentionally omitted <==**

Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 6/7 

6/2/2026 

**==> picture [428 x 255] intentionally omitted <==**

**----- Start of picture text -----**<br>
-F SIEMENS |<br>| |<br>FR op DEVICE FR<br>BUS<br>U GEN. FAULT Logic |<br>l | |: | |<br>Port 1 SIMOCODE PRO<br>‘ Sy [a Port 2 ima<br>|<br>|<br>|<br>|£ B A B A<br>i 8 1 8 1<br>A1 9 10 4 5 8 1 6<br>IN1 IN2 IN3 IN4 24V OUT1/2 OUT3<br>PE OUT1 OUT2 OUT3<br>A2 SPE T1 T2 2 3 7 -Port1:PN -Port2:PN<br>**----- End of picture text -----**<br>


**last modified:** 4/4/2026 

Subject to change without notice © Copyright Siemens 

3UF70131AB000 Page 7/7 

6/2/2026