3UF7000-1AB00-0

**3UF7000-1AB00-0** 

**Data sheet** 

basic device SIMOCODE pro C, PROFIBUS DP interface 12 Mbps, RS-485, 4 I/3 O freely configurable, Us: 24 V DC, input for thermistor connection monostable relay outputs 

|Ga 63 3 cmeh<br>o<br>OoGarearey Ces|basic device SIMOCODE pro C, PROFIBUS DP interface 12 Mbps, RS-485, 4 I/3<br>O freely configurable, Us: 24 V DC, input for thermistor connection monostable<br>relay outputs|
|---|---|
|**product brand name**|SIMOCODE|
|**product designation**|Motor management system|
|**design of theproduct**|basic unit 1|
|**product type designation**|pro C|
|**General technical data**||
|**certificate of suitability**|CE / UL / CSA / CCC / C-Tick (RCM) / GOST / NOM / ATEX / NEPSI / ABS /<br>DNV / GL / LRS / RoHS|
|**product function**||
|● current measurement|No|
|● voltage measurement|No|
|● activepower measurement|No|
|● energymeasurement|No|
|● frequencymeasurement|No|
|● bus communication|Yes|
|● data acquisition function|Yes|
|● diagnostics function|Yes|
|●passwordprotection|Yes|
|● test function|Yes|
|● maintenance function|Yes|
|● MRRT redundancy procedure|No|
|**product component**||
|● input for thermistor connection|Yes|
|● digital input|Yes|
|● input for analogtemperature sensors|No|
|● input forground fault detection|No|
|● relayoutput|Yes|
|**product extension**||
|● temperature monitoringmodule|No|
|● current measuringmodule|Yes|
|● current/voltage measuringmodule|No|
|● fail-safe digital I/O module|No|
|●ground-fault monitoringmodule|No|
|● decouplingmodule|No|
|● analogI/O module|No|
|● digital I/O module with monostable outputs|No|
|● digital I/O module with bistable outputs|No|
|● control unit with display|No|
|● control unit|Yes|
|**consumed active power**|2.3 W|



Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 1/7 

6/4/2026 

|insulation voltage with degree ofpollution 3 at AC rated value|300 V|
|---|---|
|**surge voltage resistance rated value**|4 000 V|
|**shock resistance**||
|**● according to IEC 60068-2-27**|15g/ 11 ms|
|||
|**● vibration resistance**|1 … 6 Hz / 15 mm; 6 … 500 Hz / 2g|
|**switching capacity current of the NO contacts of the relay**<br>**outputs at AC-15**||
|● at 24 V|6 A|
|● at 120 V|6 A|
|● at 230 V|3 A|
|**switching capacity current of the NO contacts of the relay**<br>**outputs at DC-13**||
|● at 24 V|2 A|
|● at 60 V|0.55 A|
|● at 125 V|0.25 A|
|**mechanical service life(operating cycles) typical**|10 000 000|
|electrical endurance(operatingcycles)typical|100 000|
|**buffering time in the event ofpower failure**|0.05 s|
|**reference code according to IEC 81346-2**|F|
|continuous current of the NO contacts of the relayoutputs||
|● at 50 °C|6 A|
|● at 60 °C|5 A|
|**type of input characteristic**|Type 1 in accordance with EN 61131-2|
|**Substance Prohibitance(day/month/year)**|05/01/2012|
|**SVHC substance name**|Lead CAS-No. 7439-92-1<br>Lead monoxide (lead oxide) CAS-No. 1317-36-8<br>2-methyl-1-(4-methylthiophenyl)-2-morpholinopropan-1-one CAS-No. 71868-<br>10-5<br>Melamine CAS-No. 108-78-1|
|**Net Weight**|0.295g|
|**Electromagnetic compatibility**||
|EMC emitted interference accordingto IEC 60947-1|class A|
|EMC immunityaccordingto IEC 60947-1|corresponds to degree of severity3|
|**conducted interference**||
|● due to burst accordingto IEC 61000-4-4|2 kV(powerports)/ 1 kV(signalports)|
|● due to conductor-earth surge accordingto IEC 61000-4-5|2 kV|
|● due to conductor-conductor surge according to IEC<br>61000-4-5|1 kV|
|● due to high-frequency radiation according to IEC 61000-<br>4-6|10 V|
|**field-based interference according to IEC 61000-4-3**|10 V/m|
|**electrostatic discharge according to IEC 61000-4-2**|6 kV contact discharge / 8 kV air discharge|
|**conducted HF interference emissions according to**<br>**CISPR11**|corresponds to degree of severity A|
|**field-bound HF interference emission according to CISPR11**|corresponds to degree of severityA|
|**Inputs/ Outputs**||
|**product function**||
|●parameterizable inputs|Yes|
|●parameterizable outputs|Yes|
|**number of inputs**|4|
|● for thermistor connection|1|
|number of digital inputs with a common referencepotential|4|
|**digital input version**||
|● type 1 acc. to IEC 61131|Yes|
|**input voltage at digital input at DC**||
|● rated value|24 V|
|**number of outputs**|3|
|**number of semiconductor outputs**|0|
|**number of outputs as contact-affected switching element**|3|
|**switching behavior**|monostable|



Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 2/7 

6/4/2026 

||**number of relay outputs**|3||
|---|---|---|---|
||**type of relay outputs**|Monostable||
||**wire length for digital signals maximum**|300 m||
||**wire length for thermistor connection**|||
||● with conductor cross-section = 0.5 mm² maximum|50 m||
||● with conductor cross-section = 1.5 mm² maximum|150 m||
||● with conductor cross-section = 2.5 mm² maximum|250 m||
||**Protective and monitoring functions**|||
||**product function**|||
||● asymmetrydetection|Yes||
||● blockingcurrent evaluation|Yes||
||●power factor monitoring|No||
||●ground fault detection|Yes||
||●ground-fault monitoring|No||
||●phase failure detection|Yes||
||●phase sequence recognition|No||
||● voltage detection|No||
||● monitoringof number of start operations|Yes||
||● overvoltage detection|No||
||● overcurrent detection 1phase|Yes||
||● undervoltage detection|No||
||● undercurrent detection 1phase|Yes||
||● activepower monitoring|No||
||**product function**|||
||● current detection|Yes||
||● overloadprotection|Yes||
||● evaluation of thermistor motorprotection|Yes||
||**total cold resistance number of sensors in series maximum**|1.5 kΩ||
||**response value of thermoresistor**|3 400 ... 3 800 Ω||
||● of the short-circuit control|9 Ω||
||**release value of thermoresistor**|1 500 ... 1 650 Ω||
||**Motor control functions**|||
||**product function**|||
||●parameterizable overload relay|Yes||
||● circuit breaker control|Yes||
||● direct start|Yes||
||● reverse starting|Yes||
||● star-delta circuit|No||
||● star-delta reversingcircuit|No||
||● Dahlander circuit|No||
||● Dahlander reversingcircuit|No||
||●pole-changingswitch circuit|No||
||●pole-changingswitch reversingcircuit|No||
||● slide control|No||
||● valve control|No||
||**Communication/ Protocol**|||
||**protocol is supported**|||
||● PROFIBUS DPprotocol|Yes||
||● PROFINET IOprotocol|No||
||● PROFIsafeprotocol|No||
||● Modbus RTU|No||
||● EtherNet/IP|No||
||● OPC UA Server|No||
||● LLDP|No||
||● Address Resolution Protocol(ARP)|No||
||● SNMP|No||
||● HTTPS|No||
||● NTP|No||
||● Media Redundancy Protocol (MRP)|No||



Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 3/7 

6/4/2026 

|**product function**||
|---|---|
|● web server|No|
|● shared device|No|
|● at the Ethernet interface Autocrossover|No|
|● at the Ethernet interface Autonegotiation|No|
|● at the Ethernet interface Autosensing|No|
|● is supported Device Level Ring (DLR)|No|
|● is supported PROFINET system redundancy (S2)|No|
|● supports PROFIenergymeasured values|No|
|● supports PROFIenergyshutdown|No|
|**transfer rate maximum**|12 Mbit/s|
|**identification & maintenance function**||
|● I&M0 - device-specific information|Yes|
|● I&M1 - higher level designation/location designation|Yes|
|● I&M2 - installation date|Yes|
|● I&M3 - comment|Yes|
|type of electrical connection of the communication interface|9-pin SUB-D socket(12 Mbit)/ screw terminal(1.5 Mbit)|
|**Installation/ mounting/ dimensions**||
|**mounting position**|any|
|**fastening method**|screw and snap-on mounting|
|**height**|111 mm|
|**width**|45 mm|
|**depth**|95 mm|
|**required spacing**||
|● top|40 mm|
|● bottom|40 mm|
|● left|0 mm|
|● right|0 mm|
|**Connections/ Terminals**||
|**product component removable terminal for auxiliary and**<br>**control circuit**|Yes|
|**type of electrical connection**||
|● for auxiliaryand control circuit|screw-type terminals|
|**type of connectable conductor cross-sections**||
|● solid|1x(0.5 ... 4.0mm²), 2x(0.5 ... 2.5 mm²)|
|● finelystranded with core endprocessing|1x(0.5 ... 2.5 mm²), 2x(0.5 ... 1.5 mm²)|
|● for AWG cables solid|1x(20 ... 12), 2x(20 ... 14)|
|● for AWG cables stranded|1x(20 ... 14), 2x(20 ... 16)|
|tighteningtorque with screw-type terminals|0.8 ... 1.2 N·m|
|tighteningtorque[lbf·in]with screw-type terminals|7 ... 10.3 lbf·in|
|**type of connectable conductor cross-sections for**<br>**PROFIBUS wire**|2x 0.34 mm², AWG 22|
|**Ambient conditions**||
|installation altitude at height above sea level maximum|2 000 m|
|● note|Restrictions apply to higher installation altitudes, see:<br>https://support.industry.siemens.com/cs/document/109995153|
|**ambient temperature**||
|● duringoperation|-25 ... +60 °C|
|● duringstorage|-40 ... +80 °C|
|● duringtransport|-40 ... +80 °C|
|**environmental category**||
|● during operation according to IEC 60721|3K6 (no formation of ice, no condensation, relative humidity 10 ... 95%), 3C3<br>(no salt mist), 3S2(sand must notget into the devices), 3M6|
|● during storage according to IEC 60721|1K6 (no condensation, relative humidity 10 ... 95%), 1C2 (no salt mist), 1S2<br>(sand must notget into the devices), 1M4|
|● duringtransport accordingto IEC 60721|2K2, 2C1, 2S1, 2M2|
|**relative humidity**||
|● duringoperation|5 ... 95 %|
|**contact rating of auxiliary contacts according to UL**|B300 / R300|
|**Short-circuit protection**||



Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 4/7 

6/4/2026 

|design of short-circuit protection per output|||Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-|Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-|Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-|Fuse links: gG 6 A, quick-response 10 A (IEC 60947-5-1), miniature circuit-||
|---|---|---|---|---|---|---|---|
||||breaker C char.: 1.6 A(IEC 60947-5-1)or 6 A(I_K < 500 A|||K < 500 A)||
|Electrical Safety||||||||
|**touch protection against electrical shock**|||finger-safe|||||
|**ATEX**<br>~~a~~||||||||
|**certificate of suitability**||||||||
|● accordingto ATEX directive 2014/34/EU|||BVS 06 ATEX F001|||||
|● acc. to Equipment and Protective System Intended for|||ITS21UKEX0464, ITS21UKEX0455X|||||
|Use in Potentially Explosive Atmospheres Regulations||||||||
|2016(S.I. 2016 No.1107)||||||||
|● accordingto UKCA|||ITS21UKEX0464|||||
|**Galvanic isolation**<br>**(electrically) protective separation according to IEC 60947-1**<br>All circuits with protective separation (double creepage paths and clearances),<br>~~a~~||||||||
||||the information in the "Protective Separation" test report, No. A0258, must be|||||
||||observed(link see further information)|||||
|**design of the electrical isolation**|||Protective separation in accordance with IEC 60947-1 for all circuits, up to|||||
||||installation altitude of 2000 m|||||
|● note|||Test report No. A0258 must be observed|||||
||||(https://support.industry.siemens.com/cs/document/109748152)|||||
|**Control circuit/ Control**<br>**product function soft starter control**<br>No<br>~~ee~~||||||||
|**type of voltage of the control supply voltage**|||DC|||||
|**control supply voltage at DC rated value**|||24 V|||||
|**control supply voltage 1 at DC rated value**|||24 V|||||
|**operating range factor control supply voltage rated value at**|**operating range factor control supply voltage rated value at**|||||||
|**DC**||||||||
|● initial value|||0.8|||||
|● full-scale value|||1.2|||||
|**inrush currentpeak**<br>● at 24 V<br>~~ee~~|||14 A|||||
|**duration of inrush currentpeak**||||||||
|● at 24 V|||0.8 ms|||||
|**Approvals Certificates**||||||||
|**Environment**|**General Product Approval**||**General Product Approval**|||||
|Environmental Con-||||||||
|firmations||||||||
|**General Product Approval**|**EMV**|||**For use in hazardous locations**|**For use in hazardous locations**|||
|c<br>eg|kK||@|||€y)||
|**For use in hazardous locations**|**Test Certificates**|||**Maritime application**||||
|Miscellaneous<br>&) ~~~~ ~~|Type Test Certific-<br>ates/Test Report<br>Special Test Certific-<br>ate<br> ~~—~~~ ~~~~~~~|||©||||
|**Maritime application**|**other**|||||**Industrial Commu-**<br>**nication**||
|©|es)|es)|Confirmation<br>es)|Confirmation||||



Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 5/7 

6/4/2026 

## **Further information** 

## **Information on the packaging** 

https://support.industry.siemens.com/cs/ww/en/view/109813875 

**Information for data generation and storage** https://support.industry.siemens.com/cs/ww/en/view/109995012 **Information- and Downloadcenter (Catalogs, Brochures,…)** https://www.siemens.com/ic10 

**Industry Mall (Online ordering system)** https://mall.industry.siemens.com/mall/en/en/Catalog/product?mlfb=3UF7000-1AB00-0 **Cax online generator** https://support.automation.siemens.com/WW/CAXorder/default.aspx?lang=en&mlfb=3UF7000-1AB00-0 **Service&Support (Manuals, Certificates, Characteristics, FAQs,...)** https://support.industry.siemens.com/cs/ww/en/ps/3UF7000-1AB00-0 

**Image database (product images, 2D dimension drawings, 3D models, device circuit diagrams, EPLAN macros, ...)** https://www.automation.siemens.com/bilddb/cax_de.aspx?mlfb=3UF7000-1AB00-0&lang=en 

**==> picture [203 x 225] intentionally omitted <==**

Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 6/7 

6/4/2026 

**==> picture [428 x 239] intentionally omitted <==**

**----- Start of picture text -----**<br>
Jee Je Jee Je Je Je eee<br>-F ~ |------------------<br>SIEMENS<br>|| + IE 7<br>DEVICE . :<br>Logic<br>BUS<br>GEN. FAULT SIMOCODE PRO<br>i k A )<br>E at<br>PROFIBUS DP<br>PROFIBUS DP<br>se ee<br>A1 9 10 4 5 8 1 6<br>IN1 IN2 IN3 IN4 24V OUT1/2 OUT3<br>PE OUT1 OUT2 OUT3<br>A2 SPE T1 T2 2 3 7 A B DP<br>**----- End of picture text -----**<br>


**last modified:** 4/4/2026 

Subject to change without notice © Copyright Siemens 

3UF70001AB000 Page 7/7 

6/4/2026