3540290000

**3540 LI** Max. 10A Charger for Li-ion batteries - switch mode 

- 3-step charge control with current detection 

- Input voltage 198-264 VAC 

- Wake up and low current start-up of deeply discharged batteries 

- Error indication for reverse polarity, short circuit, charging of wrong (lower Voltage) battery pack, defect battery and safety timer run-out 

- Fixed mains cable, 2-pin IEC 60320 available 

- Mounting bracket included 

- With NTC input on request 

- Custom specifications on request 

- Approvals: 

- Home healthcare EN 60601-1-11 

- (fixed cord versions only) 

- Medically certified: 

Safety: EN 60601-1 ed. 3.1 

- UL approved 

For updates: see ~~a~~ www.mascot.no 

## TECHNICAL SPECIFICATIONS 

**==> picture [17 x 6] intentionally omitted <==**

**----- Start of picture text -----**<br>
MEDICAL<br>**----- End of picture text -----**<br>


## **GENERAL INPUT/OUTPUT** 

**Input voltage:** 198-264 VAC **Line Frequency:** 47 – 50Hz **Switch frequency, approx.:** 65 kHz **Leakage current from batt. with mains switched off:** <170µA@29.2V **Temperature range • Operating:** -25 °C - +40 °C **• Storage:** -25 °C - +65 °C **Derating:** Approx. - 30 % at 40°C **Ripple:** < 100 mV p-p **Dimensions (L×W×H):** 210 × 113 × 53 mm **Weight:** With mains cable 1400g With IEC60320 1150g 

## **SAFETY PROTECTION EMC** 

Short circuit proof and protected against reversed polarity and thermal run-off. Prevents sparking. Charge timer: (step 2): 1h Safety timer: 72h Class II (Double insulated) 

**Protection:** 

**Insulation class: Insulation voltage Primary – secondary: Electrical safety std: EMC standards Input terminal:** 

4000VAC / 5700VDC EN/IEC/ANSI 60601 EN 60601-1-2: 2015 (Edition 4) Fixed mains cable, 2-pin IEC 60320 available Cord with open ends IP44 (IP40 w IEC 60320) 

**Output terminals: IP-code:** 

VERSIONS Step 0 < 10min Step 0 > 10min Step 1 Step 2 Step 3 (yellow) (Red: 4 blinks) (yellow) (Flash yellow) (green) ~~es~~ Cells Max outputpower (W) ~~Sy~~ Low Current start-up for deeply discharged batt. Battery voltage too low Charge Current Charge Voltage when current is:Charge term Restart CC 1A±0.4A < 1A 3 252W 20A +0.2/-0.3A 12.6V ±0.2V 12.3V ±0.1V when batt volt < 9V or max. 2 hr. CC 1A±0.2A < 1A 4 294W 17.5A +0.2/-0.3A 16.8V ±0.2V 16.4V ±0.1V when batt volt < 12V or max. 2 hr. ~~re pe~~ CC 0.8A±0.4A < 0.8A 7 294W 0A/0V 10A +0/-0.3A 29.4V ±0.2V 28.7V ±0.1V when batt volt < 21V or max. 1 hr. ~~e~~ ~~**e** ae r ee~~ CC 5A±0.2A < 0.5A 8 293W 8.7A +0.1/-0.3A 33.6V ±0.2V 32.8V ±0.1V when batt volt < 24V or max. 1 hr. CC 0.5A±0.1A < 0.5A 10 294W 7A +0/-0.3A 42.0V ±0.2V 41.0V ±0.1V when batt volt < 30V or max. 1 hr. ~~**r** t. ft.e~~ ~~**e** e eee~~ 

**TS100321** 

**Mascot AS Headquarters • PO Box 177 • 1601 Fredrikstad NORWAY • +47 69 36 43 00 • sales@mascot.no • www.mascot.no** 

## Charging characteristics and LED indication * 

**==> picture [428 x 311] intentionally omitted <==**

**----- Start of picture text -----**<br>
INDICATOR:<br>INDICATOR: YELLOW  INDICATOR: GREEN<br>FLASHING YELLOW<br>Charge Voltage Battery Voltage<br>No voltage,<br>Battery Voltage no current<br>from charger!<br>Charge Current<br>Start Current Cut-Off Current  No current (0A)<br>Low Current Start-Up at Vbatt <3V/cell<br>Error Mode if <3V/cell after 10 minutes<br>Step 0 Step 1 Step 2 Step 3<br>EET Start Timer(10 min) CC Charge CV Charge (max1 h) Charge complete<br>Safety Timer (72 hours)<br>| [—i‘(i‘(acésé‘(aéaé‘é(aa;y()N(C(wlllLLlLlLlU7—>—>—>———e]<br>**----- End of picture text -----**<br>


- _an animated video of this charging progress is available on our website_ 

## BATTERY NOT CONNECTED INDICATIONS 

Battery not connected is indicated by FLASHING GREEN. In this mode charger will apply short pulses attempting to wake up deeply discharged batteries. 

## ERROR INDICATIONS 

2 red blinks: Battery is connected to charger with wrong polarity! 

3 red blinks: Charger output is shorted. Check output cable connection! 

4 red blinks: Battery voltage is low. Check battery status or voltage. 

5 red blinks: Safety timer has run out. Check battery status or capacity. LED off: Battery voltage is too high. Check battery voltage. 

WAIT MODE INDICATIONS (For NTC versions only) Yellow with 1 red blink: Battery temperature is too low (<0°C) Yellow with 2 red blink: Battery temperature is too high (>45°C) 

**TS100321** 

**Mascot AS Headquarters • PO Box 177 • 1601 Fredrikstad NORWAY • +47 69 36 43 00 • sales@mascot.no • www.mascot.no** 

**==> picture [388 x 549] intentionally omitted <==**

**----- Start of picture text -----**<br>
53 mm<br>|<br>© | \<br>113 mm<br>ks<br>210 mm<br>(& Y<br>53 mm<br>113 mm<br>210 mm<br>141,48 mm<br>70 mm<br>104 mm<br>140 mm<br>**----- End of picture text -----**<br>


Mounting bracket, part no. 205800 

**TS100321** 

**Mascot AS Headquarters • PO Box 177 • 1601 Fredrikstad NORWAY • +47 69 36 43 00 • sales@mascot.no • www.mascot.no**