2KBP02M..

## **Bridge Rectifier** 

## **Features:** 

- In-line glass passivated single phase rectifier bridge 

- Surge overload rating: 60 Amperes peak 

- Ideal for printed circuit board 

- Reliable low cost construction utilizing moulded plastic technique 

## **Mechanical Data:** 

Terminals : Lead solderable per MIL-STD-202, Method 208 Mounting position : Any Weight : 0.06oz, 1.7g 

## **Maximum Ratings and Electrical Characteristics:** 

Ratings at 25°C ambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. 

|**Parameter**|**2KBP02M**|**2KBP08M**|**Units**|
|---|---|---|---|
|Maximum recurrent peak reverse voltage|200|800|V|
|Maximum RMS bridge input voltage|140|560||
|Maximum DC blocking voltage|200|800||
|Maximum average rectified output current at 25°C ambient|2||A|
|Peak one cycle surge overload current|60|||
|Maximum forward voltage drop per bridge element at 3.14A DC|1.1||V|
|Maximum (Total bridge) reverse leakage at rated DC blocking voltage|5||mA|
|Maximum (Total bridge) reverse leakage at rated DC blocking voltage and 100°C|0.5|||
|I2t Rating for fusing ( t <8.35ms)|15||A2Seconds|
|Typical junction capacitance per leg (Note 1) CJ|25||pF|
|Typical thermal resistance per leg (Note 2) RθJA<br>Typical thermal resistanceper leg (Note 2)RθJL|30<br>11||°C/W|
|Operating temperature range|-55 to +125||°C|
|Storage temperature range|-55 to +150|||



## **Notes:** 

1.   Measured at 1MHz and applied reverse voltage of 4V. 

2.    Thermal resistance from junction to ambient and from junction to lead mounted on PCB with 0.47" × 0.47" (12mm × 12mm) copper pads. 

www.element14.com www.farnell.com www.newark.com 

Page <1> 

31/10/12 V1.0 

## **Bridge Rectifier** 

## **Rating and Characteristics Curves** 

www.element14.com www.farnell.com www.newark.com 

Page <2> 

31/10/12 V1.0 

1. Pulse Test : Pulse Width = 300μs, Duty Cycle ≤2%. 

## **Bridge Rectifier** 

Dimensions : Inches (Millimetres) 

## **Part Number Table** 

|**Description**|**Vrrm**<br>**(V)**|**Maximum**<br>**Input Voltage**<br>**(V AC)**|**Id**<br>**at**<br>**Ifsm = 60A**|**Pin**<br>**Spacing**|**Current**<br>**Rating**<br>**(A)**|**Body**|**Body**|**Body**|**Part Number**|
|---|---|---|---|---|---|---|---|---|---|
|||||||**Height**|**Width**|**Depth**||
|Bridge Rectifier|200|140|2|4.1|2|12.7|15.24|5.08|2KBP02M|
||800|560|||||||2KBP08M|



Dimensions : Inches (Millimetres) 

**Important Notice :** This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012. 

www.element14.com www.farnell.com www.newark.com 

Page <3> 

31/10/12 V1.0