SPF240D25

**PCB Mount** _DataSheet_ 

## _**SPF Series**_ 

- SIP SSR 

- Ratings to 25A (forced air) @ 480VAC 

- SCR output for heavy industrial loads 

- AC or DC control 

- Zero turn-on (resistive loads) or instantaneous turn-on (inductive loads) output 

## **PRODUCT SELECTION** 

**==> picture [507 x 197] intentionally omitted <==**

**----- Start of picture text -----**<br>
Control Voltage 25A 25A 25A<br>3-15 VDC  SPF240D25<br>4-15 VDC  SPF380D25 SPF480D25<br>15-32 VDC  SPFE240D25 SPFE480D25<br>18-36 VAC  SPFE240A25<br>90-140 VAC  SPF240A25<br>AVAILABLE OPTIONS<br>Load Voltage<br>240:  12-280 VAC Operation Current<br>380:  48-530 VAC 25:  25 Amps<br>Series 480:  48-660 VAC<br>SPF E 240 D 25 R<br>Control Voltage Control Input Type Switching Type<br>Blank:  3-15 VDC (for 240) D:  DC Input Blank:  Zero Voltage Turn-On<br>Required for valid part number 4-15 VDC(for 380 /480) A:  AC Input R:  Instantaneous Turn-On<br>E:  15-32 VDC (for 240 / 480)<br>For options only and not required for valid part number<br>18-36 VAC (for 240 Only )<br>**----- End of picture text -----**<br>


## **AVAILABLE OPTIONS** 

## **OUTPUT SPECIFICATIONS[(1)]** 

|**Description**|**SPF(E)240**|**SPF380**|**SPF(E)480**|
|---|---|---|---|
|Operating Voltage (47-63Hz)  [Vrms]|12-280|48-530|48-660|
|Transient  Overvoltage [Vpk]|600|1200|1200|
|Maximum Off-State Leakage Current @ Rated Voltage [mArms]|0.1|0.1|0.1|
|Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec)**(2)**|500|500|500|
|Maximum Load Current (Convection Air) [Arms]**(3)**|10|10|10|
|Minimum Load Current (Forced air) [mArms]**(3)**|25|25|25|
|Minimum Load Current [mArms]|0.06|0.06|0.06|
|Maximum Surge Current (16.6msec) [Apk]|250|250|250|
|Maximum On-State Voltage Drop @ Rated Current [Vpk]|1.6|1.6|1.6|
|Maximum I²t for Fusing (8.3msec) [A²sec]|260|260|260|
|Minimum Power Factor (at Maximum load)|0.5|0.5|0.5|



## **INPUT SPECIFICATIONS[(1)]** 

|**Description**|**SPF240D25**|**SPF380D/480D**|**SPFExxxD25**|**SPF240A25**|**SPFE240A25**|
|---|---|---|---|---|---|
|Control Voltage Range|3-15 VDC|4-15 VDC|15-32 VDC|90-140 VAC|18-36 VAC|
|Maximum Turn-On Voltage|3.0 VDC|4.0 VDC|15 VDC|90 Vrms|18 Vrms|
|Minimum Turn-Off Voltage|1.0 VDC|1.0 VDC|1.0 VDC|10 Vrms|2 Vrms|
|Typical Input Current @ Nominal Voltage|15 mA|15 mA|15 mA|10 mA|10 mA|
|Nominal Input Impedance|300 Ohm|240 Ohm|1500 Ohm|14.1 k Ohm|2.1 k Ohm|
|Maximum Turn-On Time  [msec]**(4)**|1/2 Cycle|1/2 Cycle|1/2 Cycle|10|10|
|Maximum Turn-Off Time  [msec]|1/2 Cycle|1/2 Cycle|1/2 Cycle|40|40|



**Do not forget to visit us at:** _**www.crydom.com**_ 

Copyright © 2017 Crydom Inc. Specifications subject to change without notice. 

**PCB Mount** _DataSheet_ 

## **GENERAL SPECIFICATIONS[(1)]** 

|**Description**|**Parameters**|
|---|---|
|Dielectric Strength, Input/Output (50/60Hz)|4000 Vrms|
|Minimum Insulation Resistance(@ 500 VDC)|109Ohms|
|Maximum Capacitance, Input/Output|8 pF|
|Ambient Operating Temperature Range|-30 to 80°C|
|Ambient Storage Temperature Range|-30 to 125°C|
|Weight (typical)|0.85 oz (25 g)|
|Encapsulation|Thermally conductive Epoxy|



## **GENERAL NOTES** 

**(1)** 

**(2)** Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 

**(3)** Heatsink temperature 85°C Maximum 

**(4)** Turn-On Time for Instantaneous Turn-on versions 0.1 msec (DC Control Models) 

## **WIRING DIAGRAM** 

## **DC Control** 

**==> picture [230 x 153] intentionally omitted <==**

**----- Start of picture text -----**<br>
A<br>1 LOAD VAC<br>Load can be wired in position A or B<br>V2 LOAD VAC<br>TRIGGER B<br>CIRCUIT<br>3 +VDC<br>4 -VDC<br>**----- End of picture text -----**<br>


## **AC Control** 

**==> picture [231 x 154] intentionally omitted <==**

**----- Start of picture text -----**<br>
A<br>1 LOAD VAC<br>Load can be wired in position A or B<br>V2 LOAD VAC<br>TRIGGER B<br>CIRCUIT<br>3 VAC<br>  AC/DC<br>Converter<br>4 VAC<br>**----- End of picture text -----**<br>


**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2017 Crydom Inc. Specifications subject to change without notice. 

**PCB Mount** _DataSheet_ 

## **MECHANICAL SPECIFICATIONS** 

Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 

**==> picture [521 x 451] intentionally omitted <==**

**----- Start of picture text -----**<br>
1.60<br>[40.6]<br>fT<br>p puuuuL<br>1.35            000000<br>[34.2] | Nf00000Coooood |<br>0.30<br>0.05  4 3 2 1 [7.62]<br>[1.27] 0.20   0.72<br>[5.0] [18.2]<br>0.70   0.90<br>[17.7] [22.8]<br>1.10<br>+4 E<br>[27.9]<br>1.70<br>TE [43.1] L<br>.040 [1.0] DIA<br>( 4 PLACES)<br>Cee)<br>THERMAL DERATE INFORMATION<br>10 25<br>8 20<br>6 15<br>4 10<br>2 5<br>0 0<br>0 10 20 30 40 50 60 70 80 0 20 40 60 80 100 120 140<br>Ambient Temperature (ºC) Heatsink Temperature (ºC)<br>Figure 1 Convection Cooling Figure 2 Forced Air Cooling<br>Load Current (Amps) Load Current (Amps)<br>**----- End of picture text -----**<br>


## **THERMAL DERATE INFORMATION** 

## **AGENCY APPROVALS** 

**==> picture [28 x 7] intentionally omitted <==**

**----- Start of picture text -----**<br>
E116950<br>**----- End of picture text -----**<br>


Rev. 091015 

**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2017 Crydom Inc. Specifications subject to change without notice. 

**PCB Mount** _DataSheet_ 

## **DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO /** 危险 

**HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI** 存在电击、 **ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA** 爆炸或电弧 **SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O** 闪烁危险 **EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH.** • Desconectar • Eteindre **EXPLOSION.** • Spenga tutta • 在操作此设 • Disconnect all todos los toutes les • Stellen Sie l'alimentazione 备之前请先 power before suministros de sources jeglichen che fornisce 关闭电源。 installing or energia a este d'énergie de Strom ab, der questa working with equipo antes cet appareil dieses Gerät apparecchiatura this equipment. de trabajar avant de versorgt, bevor prima di lavorare 若不遵守这些说明， • Verify all connections • con este equipo.Verificar todas appareildessus de cet travailler Sie an dem Gerät Arbeiten durchführen a questa apparecchiatura 可能会导致严重的人身伤害甚至死亡。 and replace all las conexiones • Vor dem • Verificare tutti covers before y colocar todas • Vérifier tous Drehen auf i collegamenti turning on las tapas antes connections, et e sostituire Energie alle power. de energizer remettre tous Anschlüsse tutte le coperture el equipo. couverts en prima **Failure to follow** überprüfen olace avant de dell’accensione **these El** mettre sous und alle **instructions will incumplimiento** Abdeckungen **L'omissione di result in death de estas De non-suivi de** ersetzen. **queste istruzioni or serious injury. instrucciones ces instructions Unterlassung provocherà la puede provocar provoquera la dieser morte o la muerte o mort ou des Anweisungen lesioni serie lesiones serias. lésions sérieuses können zum sérieuses. Tode oder zu schweren Verletzungen führen.** 

**Failure to follow these instructions will result in death or serious injury.** 

## **WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA /** 警告 

## **RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE** 

- The product's side panels may be hot, allow 

- the product to cool before touching. 

- Follow proper mounting instructions including 

- torque values. 

- Do not allow liquids or foreign objects to enter 

- this product. 

**Failure to follow these instructions can result in serious injury, or equipment damage.** 

## **RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD** 

- Los paneles laterales del producto pueden 

- estar calientes. Esperar que el producto se enfríe antes de tocarlo. 

- Respetar las instrucciones de montaje, y en 

- particular los pares de apretado. 

- No dejar que penetren líquidos o cuerpos 

- extraños en el producto. 

**Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales.** 

## **GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG** 

## **RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER** 

- Les panneaux latéraux du produit peuvent être **•** Die Seitenwände können heiß sein. Lassen Sie 

- chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. toucher. **•** Beachten Sie die Montageanweisungen, **•** Respecter les consignes de montage, et **•** Führen Sie keine Flüssigkeiten oder notamment les couples de serrage. Fremdkörper in das Produkt ein. 

- Ne pas laisser pénétrer de liquide ni de corps 

- étrangers à l'intérieur du produit. 

**Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann des lésions corporelles graves ou des Körperverletzung oder Materialschäden dommages matériels. zur Folge haben.** 

**RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO** 

## 材料损坏和高温外壳的危险性 

• **•** I pannelli laterali dell'apparecchio possono 产品的一侧面板可能很热，在其冷却前请 不要触碰。 scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 prima di toccarlo. **•** Seguire le istruzioni di montaggio corrette. • 请勿让液体及其他异物进入本产品。 **•** Non far entrare liquidi o oggetti estranei in questo apparecchio. **La mancata osservanza di questa precauzione può** 如不能正确执行这些操作说明， **causare gravi rischi per l'incolumità personale o danni alle apparecchiature.** 极有可能造成严重人体伤害或者设备的损坏。 

**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2017 Crydom Inc. Specifications subject to change without notice. 

**PCB Mount** _DataSheet_ 

## **ANNEX - ENVIROMENTAL INFORMATION** 

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. 

|Part<br>Name|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|Toxic or hazardous Substance and Elements|
|---|---|---|---|---|---|---|
||Lead<br>(Pb)|Mercury<br>(Hg)|Cadmium<br>(Cd)|Hexavalent<br>Chromium<br>(Cr (VI))|Polybrominated<br>biphenyls<br>(PBB)|Polybrominated<br>diphenyl ethers<br>(PBDE)|
|Semiconductor die|||||||
|Solder|||||||



## 附件 - 环保信息 

此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 

|件<br>部<br>名称|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|有毒有害物质或元素|
|---|---|---|---|---|---|---|
||铅<br>(Pb)|汞<br>(Hg)|镉<br>(Cd)|六价铬<br>(Cr (VI))|多溴联苯<br>(PBB)|多溴二苯醚<br>(PBDE)|
|半导体芯片|||||||
|焊接点|||||||



**==> picture [96 x 94] intentionally omitted <==**

**----- Start of picture text -----**<br>
50<br>**----- End of picture text -----**<br>


**Do not forget to visit us at:** _**www.crydom.com**_ Copyright © 2017 Crydom Inc. Specifications subject to change without notice.